VLV/CHV have similar DSPARB registers as older platforms, just more of
them due to more planes. Add a bit of code to read out the current FIFO
split from the registers. Will be useful later when we improve the WM
calculations.
v2: Add display_mmio_offset to DSPARB
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the DDL precision handling into vlv_compute_drain_latency() so the
callers don't have to duplicate the same code to deal with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Kill the silly DRAIN_LATENCY_PRECISION_* defines and just use the raw
number instead.
v2: Move the sprite 32/16 -> 16/8 preision multiplier
change to another patch (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we must yet halve the DDL drain latency from what we're
using currently. This little nugget is not in any spec, but came
down through the grapevine.
This makes the displays a bit more stable. Not quite fully stable but at
least they don't fall over immediately on driver load.
v2: Update high_precision in valleyview_update_sprite_wm() too (Jesse)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Change 'mutliple' to 'multiple'
Change 'mutlipler' to 'multiplier'
Change 'Haswel' to 'Haswell'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Definition of VLV RR switch bit and corresponding toggling in
set_drrs function.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When one EU is disabled in a particular subslice, we can tune how the
work is spread between subslices to improve EU utilization.
v2: - Use a bitfield to record which subslice(s) has(have) 7 EUs. That
will also make the machinery work if several sublices have 7 EUs.
(Jeff Mcgee)
- Only apply the different hashing algorithm if the slice is
effectively unbalanced by checking there's a single subslice with
7 EUs. (Jeff Mcgee)
v3: Fix typo in comment (Jeff Mcgee)
Issue: VIZ-3845
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Reviewed-by: Jeff Mcgee <jeff.mcgee@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen9 the render power gating can leave slice/subslice/EU in
a partially enabled state. We must make an explicit request for
full SSEU enablement through the Render Power Clock State
register when resuming render work. This register is save/
restored in the logical ring context image for execlist
submission mode. Initialize its value in each LRC image to
request full enablement according to the device SSEU config.
Thanks to Sharma Ankitprasad and Akash Goel for highlighting the
issue and proposing the initial fix on which this patch is based.
v2: Adjusted the names of the power gating support flags to fit
update of an earlier patch.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: "Akash Goel <akash.goel@intel.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new section to the 'i915_sseu_status' debugfs entry to
report the currently enabled counts of slice, subslice, and
execution units on the device. The count of enabled subslice
per slice represents the most enabled subslice on any one
slice for devices where imbalances may exist. Similarly, the
count of enabled EU per subslice represents the most enabled
EU on any one subslice.
Collect this device status for Skylake by reading the Gen9
power gate control ack message registers. Power gate control
operates on EU in pairs, therefore our reported counts of
enabled EU can be overestimated by one for each pair in which
one EU is fused-off.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read fuse registers to determine the available slice total,
subslice total, subslice per slice, EU total, and EU per subslice
counts of the SKL device. The EU per subslice attribute is more
precisely defined as the maximum EU available on any one subslice,
since available EU counts may vary across subslices due to fusing.
Set flags indicating the SKL device's slice/subslice/EU (SSEU)
power gating capability. Make all values available via debugfs
entry 'i915_sseu_status'.
v2: Several small clean-ups suggested by Damien. Most notably,
used smaller types for the new device info fields to reduce
memory usage and improved the clarity/readability of the
method used to extract attribute values from the fuse
registers.
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added new PHY register definitions to control TDC buffer calibration and
digital lock threshold.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This W/A is put in a gen9 specific function because it may well be
needed on other gen9 platforms.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's also take the opportunity the remove the comment telling it's a
pre-prod W/A, it should be obvious from the stepping test.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we compare the whole EDRAM_PRESENT/EDRAMCAP register value
to 1 while EDRAM_PRESENT is only bit 0 (the rest may be used to describe
eDRAM capabilities).
To be more future proof, only look at bit 0 to detect eDRAM presence.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This one doesn't have one of these nice cryptic names unfortunately.
v2: Added missing register bitmap
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements core logic of SKL display power well.
v2: Addressed Imre's comments
- Added respective DDIs under power well #1 and #2
- Simplified repetitive code in power well programming
v3: Implemented Imre's comments
- Further simplified power well programming
- Made sure that PW 1 is enabled prior to PW 2
v4: Fix minor conflict with the the cherryview support (Damien)
v5: Add the PLL power domain to the always on power well (Damien)
v6: Disable BIOS power well (Imre)
Use power well data for comparison (Imre)
Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh,
Damien)
v7: Addressed Imre's comments
- Lowered the time out to 1ms
- Added parantheses in macro
- Moved debug message and fixed wait_for interval
v8:
- Add a WARN() when swiching on an unknown power well (Imre, done by Damien)
- Whitespace fixes (spaces instead of tabs) (Damien)
v9: (Imre, done by Damien)
- Merge the register definitions with this patch
- Merge the MISC IO power well in this patch
v10: (Imre, done by Damien)
- Define the Misc I/O power domains to be the power well 1 ones as Misc I/O
needs to be enabled with PW1
- Added Transcoder A and VGA domains to PW 2
- Remove the MISC_IO power domains as well in the the always on
domains definition
- Move Misc I/O power well at the top of the power well list so it's turned
on right after PW1.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.
v2: introduce EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable coarse power gating for Gen9. This feature allows render and
media engine to enter RC6 independently. Policies are configured
together with RC6. This feature will only be enabled when RC6 is
enabled.
v2: Rebase after Chris'/Mika's forcewake change (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.
v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)
v3: add break in switch conditions (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Cherryview, devices may have a varying number of EU for
a given ID due to creative fusing. Punit support different frequency for
different fuse data. We use this patch to help get total eu enabled and
read the right offset to get RP0
Based upon a patch from Jeff, but reworked to only store eu_total and
avoid sending info to userspace
v2: Format register definitions (Jani)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Found by reading the HIZ_CHICKEN documentation.
Improves performance in a HiZ microbenchmark by around 50%.
Improves performance in OglZBuffer by around 18%.
Thanks to Chris Wilson for helping me figure out where to put this.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Haswell significantly improved the performance of sampler_c messages,
but the optimization appears to be off by default. Later platforms
remove this bit, and apparently always enable the optimization.
Improves performance in "Counter Strike: Global Offensive" by 18%
at default settings on Iris Pro.
This may break sampling of paletted formats (P8/A8P8/P8A8). It's
unclear whether it affects sampling of paletted formats in general,
or just the sample_c message (which is never used).
While libva does have support for using paletted formats (primarily
for OSDs), that support appears to have been broken for at least a
year, so I couldn't observe a regression from this:
I tried to get libva-intel to use paletted formats, and observe a
regression...but the only thing I found that used it was mplayer's OSD
(on screen display). Even without my patch, the colors were totally
wrong with that, and it's according to a few distro wikis, that's been
the case for over a year.
If libva's code for paletted formats /is/ broken, they could always
add code to disable this bit using the command validator when fixing
it.
Further investigation from Haihao shows that libva mplayer OSD seems
to work at least on his setup (still unclear what's wron with Ken's),
and that it's not affected by this patch. Quoting the discussion
between Haihao and Ken:
> > > If you use "-vo gl" or "-vo xv", the OSD is solid white text with a black
> > > border around it. I presume that it's supposed to be white with vaapi as
> > > well, but I guess I'm not entirely sure.
> > >
> > > It's possible that the optimization doesn't affect the palette as long as
> > > you never use sample_c with the paletted textures.
> >
> > I verified the palette takes effect in the following way:
> >
> > 1. Only support P8A8 format in the driver
> >
> > 2. ran the above command and I saw white OSD text
> >
> > 3. Only support P4A4 format in the driver and don't use
> > 3DSTATE_SAMPLER_PALETTE_LOAD0 to load the value to the texture palette,
> > so the palette keeps unchanged.
> >
> > 4. ran the above command and I saw black OSD text.
> >
> > 5. Load the right value to the texture palette and ran the above command
> > again, I saw white OSD text.
> >
> > Hence I think sample_c with the paletted textures is used in the driver.
>
> That sounds like the palette is actually working, then. Great :)
>
> I doubt that libva would use sample_c - sampling with a shadow comparison?
> It looks like it just uses sample and sample+killpix.
You are right, libva driver doesn't use sample_c message.
> I'm pretty sure the sample_c optimization just uses the palette memory as
> storage for some stuff, so it's quite possible it just works if you're
> only using sample and sample+killpix.
Thanks for the explanation, it makes sense to me.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add wa name from Ville's review to the comment and copypaste
the explanation why we don't care about libva (already broken) from
Ken. Also add conclusion from libva devs that&why this is all fine.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Xiang, Haihao" <haihao.xiang@intel.com>
Cc: libva@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There exists a current workaround to prevent a hang on context switch
should the ring go to sleep in the middle of the restore,
WaProgramMiArbOnOffAroundMiSetContext (applicable to all gen7+). In
spite of disabling arbitration (which prevents the ring from powering
down during the critical section) we were still hitting hangs that had
the hallmarks of the known erratum. That is we are still seeing hangs
"on the last instruction in the context restore". By comparing -nightly
(broken) with requests (working), we were able to deduce that it was the
semaphore LRI cross-talk that reproduced the original failure. The key
was that requests implemented deferred semaphore signalling, and
disabling that, i.e. emitting the semaphore signal to every other ring
after every batch restored the frequent hang. Explicitly disabling PSMI
sleep on the RCS ring was insufficient, all the rings had to be awake to
prevent the hangs. Fortunately, we can reduce the wakelock to the
MI_SET_CONTEXT operation itself, and so should be able to limit the extra
power implications.
Since the MI_ARB_ON_OFF workaround is listed for all gen7 and above
products, we should apply this extra hammer for all of the same
platforms despite so far that we have only been able to reproduce the
hang on certain ivb and hsw models. The last question is whether we want
to always use the extra hammer or only when we know semaphores are in
operation. At the moment, we only use LRI on non-RCS rings for
semaphores, but that may change in the future with the possibility of
reintroducing this bug under subtle conditions.
v2: Make it explicit that the PSMI LRI are an extension to the original
workaround for the other rings.
v3: Bikeshedding variable names and whitespacing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80660
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83677
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Peter Frühberger <fritsch@xbmc.org>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the gen7 pipe control there is an extra bit to flush the media
caches, so let's set it during cache invalidation flushes.
v2: Rename to MEDIA_STATE_CLEAR to be more inline with spec.
Cc: Simon Farnsworth <simon@farnz.org.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This will allow us to read the number of dispatched compute threads
for GL_ARB_pipeline_statistics_query.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Nikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To get stable CRCs from the DP CRC source we need to reset the
scrambler for each frame. Enable the reset feature when grabbing
CRCs for pipe C on CHV. Pipes A and B were already covered due
sharing the code with VLV.
We can safely extend PIPE_SCRAMBLE_RESET_MASK to deal with CHV since
the extra bit was MBZ on the older platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Was missing.
Issue: VIZ-4701
Signed-off-by: Michael H. Nguyen <michael.h.nguyen@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.
v2: Used for_each_dsi_port macro instead of for loop
v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check
v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_DWORD_IMM length has been the same ever since gen4. Rename
the define to avoid potential confusion if someone tries to use this
on pre-gen8.
Also correct the comment on MI_MEM_VIRTUAL bit. It's present on 945,g33
and 965 only.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add USE_GGTT define for g4x+ too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Baytrail (Valleyview) and Braswell (Cherryview) uses a complete different
implementation of PSR that we currently have supported for
Haswell and Broadwell. So let's start by adding registers definitions.
I usually don't like commit that adds just registers without using,
but after I put all in one commit I realized that no one would want
to take the AR to review it so I decided to split in order to make
reviewer's life easier. Only last commit in this series will actually
enable the PSR on intel enable panel path.
But as it happens currently with HSW/BDW the plan is to let it
disabled by default (protected by kernel parameter)
while we are able to fully validate it.
v2: Remove a unused bit definition that isn't used on vlv and
reserved on chv as pointed out by Durgadoss.
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg the reset bit directly controls the reset signal. We must
assert it for >=20usec and then deassert it. Bit 1 is a RO status bit
which should also go down when the reset is no longer asserted.
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's just throw in the towel on this one and take the cheap way out.
Based on a patch from Chris Wilson, but checking for a different bit.
Chris' patch checked for even bank layout, this one here for a magic
bit. Given the evidence we've gathered (not much) both work I think,
but checking for the magic bit might be more accurate.
Anyway, works on my gm45 here.
For paranoi restrict to gen4 (and mobile), since we've only ever seen
this on gm45 and i965gm.
Also add some debugfs output so that we can skip the tiled swapping
tests properly in these cases.
v2: Clean up the quirk'ed pin count in free_object to avoid upsetting
the WARN_ON. Spotted by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28813
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45092
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits [18:16] of GEN6_GT_THREAD_STATUS_REG have always had the same
meaning since SNB. So treating them as something special for HSW doesn't
make sense to me.
Also the bits *seem* to work exactly the same way on IVB, HSW GT2 and
HSW GT3. At least intel_reg_read gives the identical results on all
platforms with and without forcewake.
Also the HSW PM guide rev 0.99 (ww05 2013) doesn't say anything about
those bits. It just says to poll for bits [2:0]. As does the more recent
BDW PM guide.
So just drop the HSW special case and treat all platforms the same way.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new AUX port irq bits where needed.
v2: Rebase on top of upstream changes
v3: Rebase on top of Oscar change to write IIR as soon as possible (Damien)
v4: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This moved around on SKL, so we need to make sure we read/write the
correct regs.
v2: fixup WIN_POS offsets (Paulo)
zero out WIN_POS reg at disable time (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuougseek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few bits have changed in MI_DISPLAY_FLIP to accomodate the new planes.
DE_RRMR seems to have kept its plane flip bits backward compatible.
v2: Rebase on top of nightly
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Remove code that is now part of intel_crtc_page_flip()
Don't use BUG() in default:
Use intel_crtc->unpin_work->gtt_offset
(Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fixup compilation due to the removal of the intel_ddi_dpll_id enum.
And add a fixme about the abuse of pipe_config here.
v3: Rebase on top of the hsw_ddi_clock_get() rename (Damien)
v4: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines the necessary SKL registers for implementing the
new clocking mechanism.
v2: Addressed review comments by Damien
- Added code comment
- Introduced enum for WRPLL values
v3: Rebase on top of nightly (minor conflict in i915_reg.h)
v4: Use 0x, not 0X (Ville)
v5: Modified as per review comments from Paulo
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3,v4)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The predicate source registers are needed to implement conditional
rendering without stalling. The two source registers are used to load
the previous values of the PS_DEPTH_COUNT register saved from
PIPE_CONTROL commands. These can then be compared and used to set the
predicate enable bit via the MI_PREDICATE command.
The command parser version number is increased to 2 to make it easier
to detect the new functionality in user space.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com> (v1)
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next so that I can keep merging patches. Specifically I
want:
- atomic stuff, yay!
- eld parsing patch from Jani.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Implement common forcewake functions shared by Gen9 features.
v2: Make the focewake_{get,put} functions static (Mika)
Small coding style fix in the function definition (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Adapt to the planes/cursor split
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines SKL specific PLANE_WM Watermark registers. It also
defines macros to get the addresses of different LP levels within a pipe.
v2: Reworked the register definitions and associated macros to make it more
generic and be able to use for_each_pipe in values computation.
Incorporated Damien's review comments and indentation.
v3: Added default values for lines and blocks. Provided mask for blocks.
v4: Prefix intermedidate (internal-only) macros with _ (Ville)
v5: Remove the lines and block defaults value (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just various stuff all over from a bunch of people. Shortlog gives a beter
overview, it's really all misc drm patches.
* tag 'topic/core-stuff-2014-11-05' of git://anongit.freedesktop.org/drm-intel:
drm/edid: add #defines and helpers for ELD
drm/dp: Add counters in the drm_dp_aux struct for I2C NACKs and DEFERs
drm: Remove compiler BUG_ON() test
drm: Fix DRM_FORCE_ON_DIGITAL use
drm/gma500: Don't destroy DRM properties in the driver
drm/i915: Don't destroy DRM properties in the driver
drm: Add a note to drm_property_create() about property lifetime
gpu: drm: Fix warning caused by a parameter description in drm_crtc.c
drm/dp-helper: Move the legacy helpers to gma500
drm/crtc: Remove duplicated ioctl code
drm/crtc: Fix two typos
gpu:drm: Fix typo in Documentation/DocBook/drm.xml
gpu: drm: drm_dp_mst_topology.c: Fix improper use of strncat
drm: drm_err: Remove unnecessary __func__ argument
drm: Implement O_NONBLOCK support on /dev/dri/cardN
CHV has a programmable CSC unit on the pipe B sprites. Program the unit
appropriately for BT.601 limited range YCbCr to full range RGB color
conversion. This matches the programming we currently do for sprites
on the other pipes and on other platforms.
It seems the CSC only works when the input data is YCbCr. For RGB
pixel formats it doesn't matter what we program into the CSC registers.
Doesn't make much sense to me especially since the register names give
the impression that RGB input data would also work. But that's how
it behaves here.
In the review discussions there's been some nice math to explain the
values obtained here. First about the YCbCr->RGB matrix:
"I had the RGB->YCbCr matrix, inverted it and the values came out. But they
should match the wikipedia article. Also keep in mind that the coefficients
are in .12 in fixed point format, hence we need a 1<<12 factor. So let's
try it:
Kb=.114
Kr=.299
(1<<12) * 255/219 ~= 4769
-(1<<12) * 255/112*(1-Kb)*Kb/(1-Kb-Kr) ~= -1605
-(1<<12) * 255/112*(1-Kr)*Kr/(1-Kb-Kr) ~= -3330
(1<<12) * 255/112*(1-Kr) ~= 6537
(1<<12) * 255/112*(1-Kb) ~= 8263
"Looks like the same values to me."
And then about the limits used for clamping:
"> where did you get these min/max?
"The hardware apparently deals in 10bit values, so we need to multiply everything
by 4 when we start with the 8bit min/max values.
Y = [16:235] * 4 = [64:940]
CbCr = ([16:240] - 128) * 4 = [-112:112] * 4 = [-448:448]
"The -128 being the -0.5 bias that the hardware already applied before
the data entered the CSC unit."
Raw data is also supplied in 10bpc in the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Copypaste explanations&math from the review discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV adds a bunch of new registers for primary plane size/position and
pipe blender setup. Initialize all those registers to avoid nasty
surprises. PRIMSIZE is especially important as without programming it
the outout will be garbled whenever the primary plane size would not
match what the BIOS set up.
Also program the sprite constant alpha register to disable the constant
alpha blending factor. This applies to vlv as well as chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor plane also supports 180 degree rotation. Add a new
"cursor-rotation" property on the crtc which controls this.
Unlike sprites, the cursor has a fixed size, so if you have a small
cursor image with the rest of the bo filled by transparent pixels,
simply flipping the rotation property will cause the visible part
of the cursor to shift. This is something to keep in mind when
using cursor rotation.
v2: Fix gen4/vlv by offsetting the base address appropriately
v3: Removing cursor-rotation property and using rotation property on cursor
plane.
v4: Changing the author name back to Ville.
v5 (by Matt Roper): Slight tweaking to apply against latest di-nightly
codebase.
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by (IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current chv spec teels we can only use either 16 or 32 bits as precision.
Although in the past VLV went from 16/32 to 32/64 and spec might not be updated,
these precision values brings stability and fixes some issues Wayne was facing.
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Wayne Boyer <wayne.boyer@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Sprinkle const as requested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I managed to fumble the per spline PCS DW11 register defines in:
commit 570e2a747b
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Aug 18 14:42:46 2014 +0300
drm/i915: Clear TX FIFO reset master override bits on chv
Fortunately the bit in DW0 that was cleared due to this didn't have
any effect as long as the bit we meant to clear was already zero.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Fix commit ref as pointed out by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for 180 degree rotation for primary and sprite planes
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This patch fix spelling typos found in drm.xml.
It is because the file is generated from comments in
source codes, I have to fix the typos within source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the override bits to make sure the hardware manages
the TX FIFO reset master on its own.
v2: Squash with the earlier attempt at forcing the override bits
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register can house two different swing marging/deemph settings at
once. However only one gets used based on some other bits. Make sure we
set those bits correctly to make the hardware use the settings we
provided.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use pack_aux() to construct the PSR exit DPMS D0 AUX message,
and use the defines from dp_dp_helper.h to populate the message
contents.
v2: Use sizeof() for message size (Jani)
Use a generic loop to write EDP_PSR_AUX_DATA registers
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell and later silicon has added a new pixel replication register
to the pipe timings for each transcoder. Now in addition to the
DPLL_A_MD register for the pixel clock double, we also need to write
to the TRANS_MULT_n (0x6002c) register to double the pixel data. Writing
to the DPLL only double the pixel clock.
ver2: Macro name change from MULTIPLY to PIPE_MULTI. (Daniel)
ver3: Do not set pixel multiplier if transcoder is eDP (Ville)
ver4: Macro name change to PIPE_MULT and default else pixel_multiplier
Cc: Ville =?iso-8859-1?Q?Syrj=E4l=E4?= <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease checkpatch and move one hunk back into the right
place that git am misplace!?]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit c76bb61a71.
It's apparently too broken so that Rodrigo submitted a patch to add a
config option for it. Given that the design is also ... suboptimal and
that I've only merged this to get lead engineers and managers off my
back for one second let's just revert this.
/me puts on combat gear again
It was worth a shot ...
References: http://mid.mail-archive.com/1411686380-1953-1-git-send-email-rodrigo.vivi@intel.com
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daisy Sun <daisy.sun@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
SKL Uses the same hardware for all planes now, so called "universal"
planes. Ie both the primary planes and sprite planes share the same
logic. This patch implements the drm_plane vfuncs for "sprites" ie
planes that aren't the primary plane.
v2: Couple of fixes:
- Actually enabled the planes and fix the plane number
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To accomodate the extra planes, the bit definitions were shuffled around
a bit.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v3: Rebase after yet another change int that area (done with wiggle)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake doesn't use the pre-charge field now, but, instead, we need to
specify the total number of SYNC pulses for the SYNC phase (pre-charge +
SYNC pattern pules). Let's use the default value (32) for that.
v3: increase DP AUX TX timeout as 400us is not to be used on SKL
apparently (Jesse).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake makes primary planes the same as sprite planes and call the
result "universal planes".
This commit emulates a primary plane with plane 0, taking the
opportunity to redefine primary and sprite registers to be identical now
that the underlying hardware is. It also makes sense as plenty of fields
have changed.
v2: Rebase on top of the vma code.
v3: Follow upstream evolution:
- Drop return values.
- Remove pipe checks since redudant and BUG instead.
- Remove tiling checks and BUG instead.
- Drop commented out DISP_MODIFY usage.
v4: s/plane/primary_plane/
v5: Misc fixes:
- Fix the fields we need to clear up
- Disable trickle feed
- Correctly use PLANE_OFFSET for the panning
v6: (Jesse)
Use pipe src size when programming plane size. This makes cloned configs
work correctly w/o the use of a panel fitter.
v7: Rebase on top of Ville's rmw elimination series
v8: Remove clearing the trickle feed bit now that we don't do a RMW (Rodrigo,
Damien)
Add a comment about the stride unit (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1,5,6,7)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2,3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based upon a patch from Deepak, but reworked to only apply on gen7+
and with the logic a bit clarified.
v2: Fix s/SHIFT/MASK/ fumble that Ville spotted.
Cc: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
Running igt, I was encountering the invalid TLB bug on my 845g, despite
that it was using the CS workaround. Examining the w/a buffer in the
error state, showed that the copy from the user batch into the
workaround itself was suffering from the invalid TLB bug (the first
cacheline was broken with the first two words reversed). Time to try a
fresh approach. This extends the workaround to write into each page of
our scratch buffer in order to overflow the TLB and evict the invalid
entries. This could be refined to only do so after we update the GTT,
but for simplicity, we do it before each batch.
I suspect this supersedes our current workaround, but for safety keep
doing both.
v2: The magic number shall be 2.
This doesn't conclusively prove that it is the mythical TLB bug we've
been trying to workaround for so long, that it requires touching a number
of pages to prevent the corruption indicates to me that it is TLB
related, but the corruption (the reversed cacheline) is more subtle than
a TLB bug, where we would expect it to read the wrong page entirely.
Oh well, it prevents a reliable hang for me and so probably for others
as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
gen2/3 platforms have a boatload of rings we're not using. On my 830
the BIOS/hw can leave some of those "active" after resume which will
prevent c3 entry. The ring is apparently considered active whenever
head != tail even if the ring is disabled.
Disable and clear all such unused ringbuffers on init/resume.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My 830 is unhappy with trickle feed enabled. The symptom is that
the image on the screen shifts a bit to right occasionally.
The BIOS initially disables trickle feed, but it gets reset during
suspend, so we need to re-disable it ourselves. Juse disable it
always.
Also disable it for all other gen2/3 platforms since we disable it
for all more recent platforms as well (until HSW that is). At least
my 855 doesn't seem to mind us doing this. I don't have gen3
hardware to test that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW supports GT C0 residency reporting in constant time unit. Driver
calculates GT utilization based on C0 residency and adjusts RP
frequency up/down accordingly. For offscreen workload specificly,
set frequency to RP0.
Offscreen task is not restricted by frame rate, it can be
executed as soon as possible. Transcoding and serilized workload
between CPU and GPU both need high GT performance, RP0 is a good
option in this case. RC6 will kick in to compensate power
consumption when GT is not active.
v2: Rebase on recent drm-intel-nightly
v3: Add flip timerout monitor, when no flip is deteced within
100ms, set frequency to RP0.
Signed-off-by: Daisy Sun <daisy.sun@intel.com>
[torourke: rebased on latest and resolved conflict]
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
init_clock_gating() is too late to read out the mem_freq. We already
want to print out the GPU MHz numbers before it's called. Move the
mem_freq setup to init_gt_powersave().
v2: Also kill the CHV_CZ_CLOCK_FREQ_MODE_* defines
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Renaming the HSW-specific macros for ddi buffer translation slot to denote the
slot and not the vswing/pre-emph values as they are platform-dependent.
This patch is based on top of the patch series for renaming the DP training
vswing/pre-emph defines:
http://lists.freedesktop.org/archives/intel-gfx/2014-August/050407.html
v2: Creating single macro with argument for slot number (Damien)
v3: Adding macro for num of translation entries (Damien)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the port as a parameter to PANEL_PORT_SELECT_VLV results in
neater code. Sadly the PCH port select bits aren't suitable for the
same treatment and the resulting macro would be much uglier, so
leave those defines as is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Primary planes support 180 degree rotation. Expose the feature
through rotation drm property.
v2: Calculating linear/tiled offsets based on pipe source width and
height. Added 180 degree rotation support in ironlake_update_plane.
v3: Checking if CRTC is active before issueing update_plane. Added
wait for vblank to make sure we dont overtake page flips. Disabling
FBC since it does not work with rotated planes.
v4: Updated rotation checks for pending flips, fbc disable. Creating
rotation property only for Gen4 onwards. Property resetting as part
of lastclose.
v5: Resetting property in i915_driver_lastclose properly for planes
and crtcs. Fixed linear offset calculation that was off by 1 w.r.t
width in i9xx_update_plane and ironlake_update_plane. Removed tab
based indentation and unnecessary braces in intel_crtc_set_property
and intel_update_fbc. FBC and flip related checks should be done only
for valid crtcs.
v6: Minor nits in FBC disable checks for comments in intel_crtc_set_property
and positioning the disable code in intel_update_fbc.
v7: In case rotation property on inactive crtc is updated, we return
successfully printing debug log as crtc is inactive and only property change
is preserved.
v8: update_plane is changed to update_primary_plane, crtc->fb is changed to
crtc->primary->fb and return value of update_primary_plane is ignored.
v9: added rotation property to primary plane instead of crtc. Removing reset
of rotation property from lastclose. rotation_property is moved to
drm_mode_config, so drm layer will take care of resetting. Adding updation of
fbc when rotation is set to 0. Allowing rotation only if value is
different than old one.
v10: Calling intel_primary_plane_setplane instead of update_primary_plane in
set_property(Daniel).
v11: Using same set_property function for both primary and sprite, Adding
primary plane specific code in the same function (Matt).
v12: Removing disabling/ enabling of fbc from set_property because it is done
from intel_pipe_set_base. Other formatting
v13: we need to call disable_fbc before changing the rotation to 180,
disable_fbc from intel_pipe_set_base gets called very late, that will
be used to re-enable fbc if rotation is set to 0 (Ville).
Testcase: igt/kms_rotation_crc
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
[danvet: Add FIXME to explain why we need the open-coded update_fbc
hunk to disable fbc when rotated 180 degree. And make checkpatch
happier.]
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
845/865 support different cursor sizes as well, albeit a bit differently
than later platforms. Add the necessary code to make them work.
Untested due to lack of hardware.
v2: Warn but accept invalid stride (Chris)
Rewrite the cursor size checks for other platforms (Chris)
v3: More polish and magic to the cursor size checks (Chris)
v4: Moar polish and a comment (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to attend context switch interrupts from all rings. Also, fixed writing
IMR/IER and added HWSTAM at ring init time.
Notice that, if added to irq_enable_mask, the context switch interrupts would
be incorrectly masked out when the user interrupts are due to no users waiting
on a sequence number. Therefore, this commit adds a bitmask of interrupts to
be kept unmasked at all times.
v2: Disable HWSTAM, as suggested by Damien (nobody listens to these interrupts,
anyway).
v3: Add new get/put_irq functions.
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com> (v2 & v3)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Drop the GEN8_ prefix from the context switch interrupt
define and move it to its brethren.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Very similar to the legacy add_request, only modified to account for
logical ringbuffer.
v2: Use MI_GLOBAL_GTT, as suggested by Brad Volkin.
v3: Unify render and non-render in the same function, as noticed by
Brad Volkin.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For the most part, logical ring context objects are similar to hardware
contexts in that the backing object is meant to be opaque. There are
some exceptions where we need to poke certain offsets of the object for
initialization, updating the tail pointer or updating the PDPs.
For our basic execlist implementation we'll only need our PPGTT PDs,
and ringbuffer addresses in order to set up the context. With previous
patches, we have both, so start prepping the context to be load.
Before running a context for the first time you must populate some
fields in the context object. These fields begin 1 PAGE + LRCA, ie. the
first page (in 0 based counting) of the context image. These same
fields will be read and written to as contexts are saved and restored
once the system is up and running.
Many of these fields are completely reused from previous global
registers: ringbuffer head/tail/control, context control matches some
previous MI_SET_CONTEXT flags, and page directories. There are other
fields which we don't touch which we may want in the future.
v2: CTX_LRI_HEADER_0 is MI_LOAD_REGISTER_IMM(14) for render and (11)
for other engines.
v3: Several rebases and general changes to the code.
v4: Squash with "Extract LR context object populating"
Also, Damien's review comments:
- Set the Force Posted bit on the LRI header, as the BSpec suggest we do.
- Prevent warning when compiling a 32-bits kernel without HIGHMEM64.
- Add a clarifying comment to the context population code.
v5: Damien's review comments:
- The third MI_LOAD_REGISTER_IMM in the context does not set Force Posted.
- Remove dead code.
v6: Add a note about the (presumed) differences between BDW and CHV state
contexts. Also, Brad's review comments:
- Use the _MASKED_BIT_ENABLE, upper_32_bits and lower_32_bits macros.
- Be less magical about how we set the ring size in the context.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com> (v2)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program DDL register as part of sprite watermark programming for CHV and VLV.
v2: Rename DRAIN_LATENCY_MAX by DRAIN_LATENCY_MASK
v3: Addressed review comments by Ville
- Changed Sprite DDL definitions to more generic to avoid multiple if-else
- Changed bit masking to customary form
- Changed to bitwise shorthand operator for sprite_dl assignment
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modify drain latency computation to use it for any plane. Same function can be
used for primary, cursor and sprite planes.
v2: Adressed review comments by Imre and Ville.
- Moved clock round up in separate patch
- Added WARN check for clock and pixel size
- Simplified bit masking
- Use cursor_base instead of reg read
v3: Changed to bitwise shorthand operator for plane_dl assignment.
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the semi-funky cmnlane assert/deassert macros with something a
bit more conventional. Also protect the macro arguments properly (also
for PHY_POWERGOOD()).
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The VLV/CHV DDL registers are uniform, and neatly enough the register
offsets are sane so we can easily unify them to a single set of defines
and just pass the pipe as the parameter to compute the register offset.
Note that we now fill out the drain latency for pipe C on CHV which we
didn't do before. The rest of the pipe C watermarks are still untouched
but that will be remedied later by adding a proper cherryview_update_wm()
function.
v2: Add a note about CHV pipe C changes (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add defines for all the watermark registers on modernish gmch platforms.
VLV has increased the number of bits available for certain watermaks so
expand the masks appropriately. Also vlv and chv have added some extra
FW registers.
Not sure what happened on chv because a new register called FW9 is now
at the offset where FW7 was on vlv, while FW7 and FW8 (another new
register) have been moved off somewhere else. Oh well, well just need
two defines for FW7 then.
v2: Fix DSPHOWM1 offset (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sprite planes (in fact all display planes starting from gen4)
support 180 degree rotation. Add the relevant low level bits to the
sprite code to make use of that feature.
The upper layers are not yet plugged in.
v2: HSW handles the rotated buffer offset automagically
v3: BDW also handles the rotated buffer offset automagically
Testcase: igt/kms_rotation_crc
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this bit enabled, HW changes the color when compressing frames for
debug purposes.
ALthough the simple way to enable a single bit is over intel_reg_write,
this value is overwriten on next update_fbc so depending on the workload
it is not possible to set this bit with intel-gpu-tools. So this patch
introduces a persistent way to enable false color over debugfs.
v2: Use DEFINE_SIMPLE_ATTRIBUTE as Daniel suggested
v3: (Ville) only do false color for IVB+ since according to spec bit is
MBZ before IVB.
v4: We don't have FBC on valleyview nor on cherryview (Ben)
v5: s/!HAS_PCH_SPLIT/!HAS_FBC (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV display PHY registes have two swing margin/deemph settings. Make it
clear which ones we're using.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like the Punit is supposed to support the 400MHz cdclk directly on
chv, so we don't need the vlv tricks.
FIXME: Punit doesn't seem ready for this yet on current hw
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the TX wells for port D. The Punit subsystem numbers are a total
guess at this time. Also I'm not sure these even exist. Certainly the
Punit in current hardware doesn't deal with these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a power well for each pipe. Add the code to deal with them.
The Punit in current hardware doesn't seem ready for this yet, so
leave it iffed out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has two display PHYs so there are also two cmnlane power wells. Add
the approriate code to power the wells up/down.
Like on VLV we do the cmnreset assert/deassert and the DPLL refclock
enabling at approriate times.
This code actually works on my bsw.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register to read cz count is different from vlv. Also
the counts returned from CCK_CTL1 for BSW are (ticks in 30ns - 1).
czcount_30ns of value 1 is a special case for 320Mhz.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80703
Suggested-by: Deepak S <deepak.s@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need mem_freq or cz clock for freq/opcode conversion
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still tacked onto the side, but slowly getting there.
v2: Don't forget the debugfs file.
v3 (from Paulo): Don't forget to check the power domains.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Luckily the bit definitions match, but it's still confusing
to use one when handling the other. So sprinkle some OCD over
the #defines to make them match and use the right version in
each place.
Maybe we should unify these definitions completely, but that
can always be done sometime in the future.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On most gen2-4 platforms the GTT can be (or maybe always is?)
inside the stolen memory region. If that's the case, reduce the
size of the stolen memory appropriately to make make sure we
don't clobber the GTT.
v2: Deal with gen4 36 bit physical address
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With RC6 enabled, BYT has an HW issue in determining the right
Gfx busyness.
WA for Turbo + RC6: Use SW based Gfx busy-ness detection to decide
on increasing/decreasing the freq. This logic will monitor C0
counters of render/media power-wells over EI period and takes
necessary action based on these values
v2: Refactor duplicate code. (Ville)
v3: Reformat the comments. (Ville)
v4: Enable required counters and remove unwanted code (Ville)
v5: Added frequency change acceleration support and remove kernel-doc
style comments. (Ville)
v6: Updated comment section and Fix w/a comment. (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore waits use a new instruction, MI_SEMAPHORE_WAIT. The seqno to
wait on is all well defined by the table in the previous patch. There is
nothing else different from previous GEN's semaphore synchronization
code.
v2: Update macros to not require the other ring's ring->id (Chris)
v3: Add missing VCS2 gen8_ring_wait init besides
s/ring_buffer/engine_cs (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Semaphore signalling works similarly to previous GENs with the exception
that the per ring mailboxes no longer exist. Instead you must define
your own space, somewhere in the GTT.
The comments in the code define the layout I've opted for, which should
be fairly future proof. Ie. I tried to define offsets in abstract terms
(NUM_RINGS, seqno size, etc).
NOTE: If one wanted to move this to the HWSP they could. I've decided
one 4k object would be easier to deal with, and provide potential wins
with cache locality, but that's all speculative.
v2: Update the macro to not need the other ring's ring->id (Chris)
Update the comment to use the correct formula (Chris)
v3: Move the macros the ringbuffer.h to prevent churn in next patch
(Ville)
v4: Fixed compilation rebase conflict
commit 1ec9e26dda
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Feb 14 14:01:11 2014 +0100
drm/i915: Consolidate binding parameters into flags
v5: VCS2 rebase
Replace hweight_long with hweight32
v6 (Rodrigo): * Add missed VC2 gen8 ring signal init
* fixing conflicst on rebase
* minor fixes on address table
* remove WARN_ON
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid using magic values for CCK frequency bits. Also the mask we were
using for the requested frequency was one bit too short. Fix it up.
Note: This also fixes the #define for a mask (spotted by Jesse in his
review).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add note about mask change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Beignet needs these in order to program the L3 cache config for
OpenCL workloads, particularly when using SLM.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two BSpec updates changed the recommended values for BDW eDP and DP
DDI buffer translations. Now the signal levels also match the HSW signal
levels, which simplify things a little bit.
It seems some DP sinks don't work properly without voltage level 0 and
pre-emphasis level 3, so this patch may fix some bugs on
panels/monitors that happen on BDW but not on HSW.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When link is in stand by and PSR exit is triggered by a primary or sprite
plane flip this mode allows only one single updated frame to be send to
display than get back to PSR immediately.
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For no reason at all the public docs lack them, and Dave needs them
for his hpd interrupt rework.
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conceptually, the MIPI registers are addressed by the MIPI transcoder
index, not the pipe. It doesn't matter right now, because there's a
1:1 relationship between pipes and MIPI transcoders, but that change
allows us to break that link in the future
V1: Created new patch to address Damien's review comment.
Replacing _PIPE calls to _TRANSCODER calls
V2: Re-basing on patch 2
V3: Re-basing on patch 2
V4: Re-basing on patch 2
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Re-define MIPI register definitions in such a way that most of
the existing DSI code can be re-used for future platforms. Register
definitions are re-written using MMIO offset variable, so that without
changing the existing sequence, same code can be generically applied.
V4: Addressing review comments by Damien and Ville, splitting into two patches
This patch removes all the un-necessary formatting changes from previous patch.
V5: Removed 80 char limit formatting for existing MIPI regs
V6: Removed extra space, change one definition
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DIP registers are a mess on VLV and CHV. The register block on pipe
A is different than the register block on pipes B and C. In order to
handle that using the pipe offsets, we'd need a new pipe offset per
register, which seems wasteful. So instead just use the _PIPE3() macro
to handle these registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are just single registers so wasting space for the pipe offsets
seems a bit pointless. So just use the _PIPE3() macro instead.
Also rewrite the _PIPE3() macro to be more obvious, and protect the
arguments properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Disable media turbo and Add DOWN_IDLE_AVG support (Ville)
v3: Mass rename of the dev_priv->rps variables in upstream.
v4: Rebase against latest code. (Deepak)
v5: Rebase against latest nightly code. (Deepak)
v6: Rename the variables to match the spec (Mika)
v7: change min/max freq variable naming to match spec (Mika)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Configure PCBR if BIOS fails allocate pcbr (deepak)
v3: Fix PCBR condition check during CHV RC6 Enable flag set
v4: Fixup PCBR comment msg. (Chris)
Rebase against latest code (Deak)
Fixup Spurious hunk (Ben)
v5: Fix PCBR and commentis msg (mika)
v6: Rebase patch on latest nightly (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
85x also has a similar AGPBUSY# bit as gen3. Enable it to make
sure vblank interrupts don't get dealyed during C3 state.
There's also another bit which controls whether AGPBUSY# is asserted
based on pending cacheable cycles and interrupts, or just based on
pending commands in the ring and interrupts. Select the cacheable
cycles mode since that seems to be the new way of doing things in
85x, and it does give slightly better C3 residency numbers with
glxgears running.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My Gen3 Bspec lists the AGPBUSY# bit in INSTPM as an enable bit rather
than a disable bit. Our code has the opposite idea. Make the code match
the spec.
Might fix some gen3 C3 related interrupt delivery problems. Untested
due to lack of hardware.
v2: call it AGPBUSY_INT_EN to make it clearer it has to do with interrupts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we need to disable VCP unit clock gating around media reset
on g4x.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Gen4+ platforms (except BDW), Render Cache Operational flush
cannot be enabled.
This WA is apparently required for all Gen4+ platforms,except BDW.
In BDW, the bit has been repurposed otherwise.
This has been tested only on vlv.
v2: Corrected the code regarding the wrong usage of
MASKED_BIT_DISABLE (Chris)
v3: Enhancing the scope of WA to Gen4+ platforms except BDW (Ville)
v4: Adding WA for g4x, crestline, broadwater (Ville)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The framecount register was still using the old PIPE macro instead
of the new PIPE2 macro
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For error state, like the recent modification to ACTHD, FADD also gets
an upper dword. This is useful for debug to make sure the fetch address
and head are similar.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mesa needs to be able to write OACONTROL in order to expose the
Observability Architecture's performance counters via OpenGL.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add comment that this is just a temporary work-around and
that we need to check more things before we can allow OACONTROL writes
for real everywhere.]
[danvet 2: Squash in fixup to avoid a DRM_ERROR due to unsorted reg
list, spotted by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL and MI_FLUSH_DW have bits that would write to the
hardware status page. The driver stores request tracking info
there, so don't let userspace overwrite it.
v2: trailing comma fix, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Various commands that access memory have a bit to determine whether
the graphics address specified in the command should use the GGTT or
PPGTT for translation. These checks ensure that the bit indicates
PPGTT translation.
Most of these checks use the existing bit-checking infrastructure.
The PIPE_CONTROL and MI_FLUSH_DW commands, however, are multi-function
commands. The GGTT/PPGTT bit is only relevant for certain uses of the
command. As such, this change also extends the bit-checking code to
include a "condition" mask and offset. If the condition mask is non-zero
then the parser only performs the bit check when the bits specified by
the condition mask/offset are also non-zero.
NOTE: At this point in the series PPGTT must be enabled for the parser
to work correctly. If it's not enabled, userspace will not be setting
the PPGTT bits the way the parser requires. VLV is the only platform
where this is a problem, so at this point, we disable parsing for VLV.
v2: whitespace and trailing commas fixes, rebased
OTC-Tracker: AXIA-4631
Change-Id: I3f4c76b6734f1956ec47e698230f97d0998ff92b
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver leaves most interrupts masked during normal operation,
so there would have to be additional work to enable userspace to
safely request/receive an interrupt.
v2: trailing commas, rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
MI_STORE_REGISTER_MEM, MI_LOAD_REGISTER_MEM, and MI_LOAD_REGISTER_IMM
commands allow userspace access to registers. Only certain registers
should be allowed for such access, so enable checking for those commands.
Each ring gets its own register whitelist.
MI_LOAD_REGISTER_REG on HSW also allows register access but is currently
unused by userspace components. Leave it rejected.
PIPE_CONTROL and MEDIA_VFE_STATE allow register access based on certain
bits being set. Reject those as well.
v2: trailing commas, rebased
OTC-Tracker: AXIA-4631
Change-Id: Ie614a2f0eb2e5917de809e5a17957175d24cc44f
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are used to implement scanline waits in the X server.
v2: Use #defines instead of magic numbers
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These registers are currently used by mesa for blitting,
transform feedback extensions, and performance monitoring
extensions.
v2: REG64 macro
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec defines most of these commands as privileged. A few others,
like the semaphore mbox command and some display commands, are also
reserved for the driver's use. Subsequent patches relax some of
these restrictions.
v2: Rebased
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add command tables defining irregular length commands for each ring.
This requires a few new command opcode definitions.
v2: Whitespace adjustment in command definitions, sparse fix for !F
OTC-Tracker: AXIA-4631
Change-Id: I064bceb457e15f46928058352afe76d918c58ef5
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently not an issue since we don't emit sempahores, but better
not forget about those.
As a little prep work extract the ipehr decoding for cleaner control
flow. And apply a bit of polish.
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The documentation calls this GFX_MODE bit "Flush TLB invalidate Mode".
However, that is not a good name for an enable bit as it doesn't make it
clear what is enabled. An even worse name is GFX_TLB_INVALIDATE_ALWAYS
as enabling that bit actually prevents the TLB from being invalidated at
every flush. This leads to great confusion when reading code and
proposed patches. To get around this try to bake in what is enabled by
setting the bit and call it GFX_TLB_INVALIDATE_EXPLICIT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gupta, Sourab" <sourab.gupta@intel.com>
Acked-by: "Gupta, Sourab" <sourab.gupta@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As Broadwell has an increased virtual address size, it requires more
than 32 bits to store offsets into its address space. This includes the
debug registers to track the current HEAD of the individual rings, which
may be anywhere within the per-process address spaces. In order to find
the full location, we need to read the high bits from a second register.
We then also need to expand our storage to keep track of the larger
address.
v2: Carefully read the two registers to catch wraparound between
the reads.
v3: Use a WARN_ON rather than loop indefinitely on an unstable
register read.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk which conflicted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not implementing this W/A can lead to hangs.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch we allow larger cursor planes of sizes 128x128
and 256x256.
v2: Added more precise check on size while setting cursor plane.
v3: Changes related to restructuring cursor size restrictions
and DRM_DEBUG usage.
v4: Indentation related changes for setting cursor control and
implementing DRM_CAP_CURSOR_WIDTH and DRM_CAP_CURSOR_HEIGHT
Testcase: igt/kms_cursor_crc
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: G, Pallavi <pallavi.g@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
make sure we wait for rings to become idle once they are
disabled. In case of timeout print an error message
Signed-off-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
[danvet: Frob patch as suggested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command parser scans batch buffers submitted via execbuffer ioctls before
the driver submits them to hardware. At a high level, it looks for several
things:
1) Commands which are explicitly defined as privileged or which should only be
used by the kernel driver. The parser generally rejects such commands, with
the provision that it may allow some from the drm master process.
2) Commands which access registers. To support correct/enhanced userspace
functionality, particularly certain OpenGL extensions, the parser provides a
whitelist of registers which userspace may safely access (for both normal and
drm master processes).
3) Commands which access privileged memory (i.e. GGTT, HWS page, etc). The
parser always rejects such commands.
See the overview comment in the source for more details.
This patch only implements the logic. Subsequent patches will build the tables
that drive the parser.
v2: Don't set the secure bit if the parser succeeds
Fail harder during init
Makefile cleanup
Kerneldoc cleanup
Clarify module param description
Convert ints to bools in a few places
Move client/subclient defs to i915_reg.h
Remove the bits_count field
OTC-Tracker: AXIA-4631
Change-Id: I50b98c71c6655893291c78a2d1b8954577b37a30
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we'll need to access the rest of the fields in
the punit power gating register, so prepare for that.
v2:
- add doc reference for the power well subsystem IDs (Jesse)
- remove IDs for non-existant DPIO_RX[23] subsystems (Jesse)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two names for the same register CHICKEN_PIPESL_1 and
HSW_PIPE_SLICE_CHICKEN_1. Unify it to just one.
Also rename the FBCQ disable bit to resemble the name we've
given to a similar bit on earlier platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec we need to always set this magic bit in ring buffer
mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben and I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Shuffle lines to group all ROW_CHICKEN writes and add a
cautious comment that this might not be needed on production hw.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fix whitespace fail spotted by checkpatch. Also add missing
:bdw w/a tag that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit e4e0c058a1
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Wed Feb 8 12:53:50 2012 -0800
drm/i915: gen7: Implement an L3 caching workaround.
the L3 cache aging was disabled. This was part of a shotgun response
to a number of GPU hang bugs, but there appears to be no documentation
to suggest that disabling the L3 cache age was ever required (to prevent
the GPU hangs).
Restoring the L3 cache age is a minor performance win of around 2%
on IVB:GT2. (Note that this value seems to be consistent across a number
of tests and so appears to be above the usual noise.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec recommends using 8x4 hashing mode when MSAA is used. But in
practice 16x4 seems to have a slight edge in performance (on IVB and
HSW at least). So just use 16x4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB we set up WaSetupGtModeTdRowDispatch:snb early in
gen6_init_clock_gating(). That sets a bit in the GEN6_GT_MODE register.
However later we go and disable all the bits in the same register. And
then we go on to set some other bit. So apparently we never actually
implemented this workaround since the "disable all bits" part was there
already before the w/a got supposedly implemented.
These are the relevant commits:
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
commit f8f2ac9a76
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Wed Oct 3 19:34:24 2012 -0700
drm/i915: Fix GT_MODE default value
So, let's drop the "disable all bits" part, move both writes to
closer proxomity to each other, and name the WIZ hashing bits
appropriately. BSpec is still a bit confused how the bits should
actually be interpreted, but I took the the description for the
high bit since the low bit part only lists values for a single bit.
Also add a comment about our choice of WIZ hashing mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a couple of switch cases to compute the port value for the
VIDEO_DIP_CTL register. Replace them with a simple macro.
We do lose a few BUG() calls, but many people may consider that
an improvement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a bit of polish which I hope will help me with massaging some
internal patches to use Imre's reworked pipestat handling:
- Don't check for underrun reporting or enable pipestat interrupts
twice.
- Frob the comments a bit.
- Do the iir PIPE_EVENT to pipe mapping explicitly with a switch. We
only have one place which does this, so better to make it explicit.
v2: Ville noticed that I've broken the logic a bit with trying to
avoid checking whether we're interested in a given pipe twice. push
the PIPESTAT read down after we've computed the mask of interesting
bits first to avoid that duplication properly.
v3: Squash in fixups from Imre on irc.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FUSE_STRAP has a bit to inform us that the display has been fused off.
Use it to setup the definitive number of pipes at run-time.
v2: actually tweak num_pipes, not num_planes
v3: also tests SFUSE_STRAP bit 7
v4: rebase on top of drm-nightly
use DRM_INFO() for the message telling display is fused off
try to read the FUSE_LOCK bit to determine if PCH display is disabled
v5: Don't read SFUSE_STRAP (register on the PCH) if num_pipes is already 0
from the initial device info struct (to prevent hangs) (Daniel Vetter)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v3)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v3)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call the handlers for pending pipestat interrupt events even if
they aren't explicitly enabled by i915_enable_pipestat(). This isn't an
issue for events other than the vblank start event, since those are
always enabled anyways. Otoh, we enable the vblank start event
on-demand, so we'll end up calling the vblank handler at times when they
are disabled.
I haven't checked if this causes any real problem, but for consistency
and to remove some overhead we should still fix this by clearing /
handling only the enabled interrupt events. Also this is a dependency
for the upcoming VLV power domain patchset where we need to disable all
the pipestat interrupts whenever the display power well is off.
v2:
- inline the status->enable mask mapping (Ville)
- don't check for invalid PSR bit on platforms other than VLV (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob conflict due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV we can't get at the pipestat status bits by simply right
shifting the corresponding enable bits. The mapping between enable and
status bits for the sprite0,1 flip done and the PSR events don't follow
this rule, so we need to map them separately.
The PSR enable for pipe A is DPFLIPSTAT[22], but I haven't added support
for this, since there is no user of it atm. Until support is added WARN
if someone tries to enable PSR interrupts, or tries to enable the same
(1 << 6) bit on pipe B, which MBZ.
v2:
- inline the status->enable mask mapping (Ville)
- fix bogus use of status bits in enable mask (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There isn't any PSR interrupt enable bit for pipe A, so we couldn't
enable it through the current API. Passing the corresponding status bits
solves this and also makes the mapping between enable and status bits
simpler on VLV (addressed in an upcoming patch).
Except of checking for invalid status bit arguments, no functional
change.
v2: split out the low level parts of i915_enable_pipestat accepting
separate enabled and status masks, to make the non-standard mapping
between those masks stand out more (added in the next patch)
(Jesse,Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had 2 set of defines for the same register, so make it one.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out it'd be nice to change some device information at run-time or simply
have some code to fill in the info struct instead of having to declare the
values in 30+ structures.
What prompted this change is handling fused out display/pipe and tweaking
num_pipes at run-time, but I'm quite sure we'll find other flags/limits to
stick into dev_priv->info.
Most of the changes were done with a sed:
sed -i -e 's/dev_priv->info->/dev_priv->info./g' drivers/gpu/drm/i915/*[ch]
with a few tweaks to make it all work:
- Change the field definition in struct drm_i915_private
- adjust i915_dump_device_info()
- adjust i915_driver_load()
- adjust the INTEL_INFO() macro
v2: cast the info pointer returned by INTEL_INFO() to be const to catch
uses that would modify the structure post-initialization.
(Ville Syrjälä)
v3: Redo the patch onto latest drm-nightly,
Keep the info field const to catch post initialization writes
instead of the v2 solution,
Use a direct structure copy for the initial info initialization to
use the compiler type safety (Ville Syrjälä)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (for v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (for v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to Bspec we need to disable SF pipelined attribute fetch
whenever SF outputs exceed 16 and normal clip mode is used. A quick
glance at Mesa suggests that these conditions could happen. So let's
just always set the magic bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
s/FLIPDONE/FLIP_DONE/ to make all FLIP_DONE macro names consistent.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The optimization is available on Ivy Bridge and later, and is disabled by
default. Enabling it helps certain workloads such as GLBenchmark TRex test.
No piglit regression.
v2
- no need to save the register before suspend as init_clock_gating can
correctly program it after resume
- split IVB change to another commit
Signed-off-by: Chia-I Wu <olv@lunarg.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least I couldn't find it in the Haswell Bspec any more and we've
tried to test-boot a Haswell machine with num_pipes forced to 0 (i.e.
hit the PCH_NOP path) and the unclaimed register logic complained.
So restrict this dance to just ivb platforms.
v2: Art pointed out that the bits simply moved on hsw+
v3: Buy code terseneness with a notch of sublety as suggested by
Chris.
v4: Frob the right bit, spotted by Art.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Having a 4 byte register at 0x321b seems unlikely as that's not
4 byte aligned. Since later platforms have more or less the same FBC
registers with new names, assume that FBC_FENCE_OFF is at 0x3218 just
like DPFC_FENCE_YOFF.
This feels like a simple typo in BSpec. 321Bh looks a lot like 3218h
after all.
Should still be tested on real hardware of course. But I don't have
any mobile gen4 systems.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the FBC plane macros take the plane as a parameter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out and calculate the port and pixel clocks on DDI configs as well.
This means we have to grab the DP divider values and look at the port
mapping to figure out which clock select reg to read out.
v2: do the work from ddi_get_config (Ville)
v3: check WRPLL reference clock (Ville)
add additional SPLL freqs (Ville)
clean up port/crtc clock calc (Ville)
fix up crtc_clock conditionals (Ville)
drop superfluous dp_get_m_n from get_config (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was forgotten in
commit 565ee3897f
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 13 12:56:29 2013 +0200
drm/i915: do not save/restore backlight registers in KMS
Since the confusion was likely due to the duplicated definition for
this pci config register, let's unify that, too.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 446f254566.
I've left the masking in the pageflip code since that seems to be some
useful piece of preemptive robustness.
Iirc I've merged this patch under the assumption that the BIOS leaves
some random gunk in the lower bits and gets unhappy if we trample on
them. We have quite a few case like this, so this made sense.
Now I've just learned that there's actual hardware features bits in
the low 12 bits, and the kernel needs to preserve them to allow a
userspace blob to do its job. Given Dave Airlie's clear stance on
userspace blob drivers I've quickly chatted with him and he doesn't
seem too happy. So let's revert this.
If there are indeed bits that we must preserve in this range then we
can ressurrect this patch, but with proper documentation for those
bits supplied. And we probably also need to think a bit about
interactions with our driver.
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix typo possibly leading to timed out DP aux transactions on ports C,D.
Introduced in:
Commmit 4aeebd7443
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 31 09:53:36 2013 +0100
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72210
Signed off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many of the fields from Gen6 have gone away for vlv. Strip all those
fields that are not relevent and try to update fields that we care
about. This patch give information about current RP & RC status and
individual Wells.
v2: Move Render & Media Well status to separate lines (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On IVB the display data buffer partitioning control lives in the
DISP_ARB_CTL2 register. Add the relevant defines/code for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few command were out of numerical order and had different spacing. Put
them back in numerical order, with proper spacing.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaVSRefCountFullforceMissDisable and
WaDSRefCountFullforceMissDisable
VS is a carry-over from HSW, and DS is likely not used by anyone yet.
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Line of 106 chars is too long. Really.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I stumbled on to some unimplemented errata. To be honest, I am not
really sure of the impact, just that the docs say to do.
No w/a name for this one.
v2: v1 was a stale thing which should have never seen the light of day.
(Haihao)
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every ring seems to have a BB_ADDR registers, so include them all in the
error state.
v2: Also include the _UDW on BDW
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilons <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setting this bit restores all ring contexts in parallel rather than
serially. Matches current BWG recommendations.
Tested-by: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Deepak S <deepak.s@inel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV the GTFIFOCTL register has other bits besides the number of free
entries in the GT wake FIFO. Apply a mask when we read th register to
make sure we don't misinterpret the number of free FIFO entries.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: There's some unclarity about hsw, but brushed off as todays'
Bspec just acting up a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV GTFIFODBG has more bits. Just report them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We send the primary and cursor plane data through the gamma unit.
In order to get matching output from sprites, also send the sprite
data through the gamma unit.
In the future we should add some properties to control this
explicitly, and also add properties for the per-sprite gamma ramps
what have you, but for now this seems like a reasonable thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec tells us that we need to emit an SRM after the LRI
to MSG_FBC_REND_STATE.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we have this everywhere. Next up would be to wire up the DP
hotplug pin to speed up panel power sequencing for eDP panels ...
I've decided to leave the has_aux_irq logic in the code, it should
come handy for hw bringup.
For testing/fail-safety the dp aux code already has a timeout when
waiting for interrupts to signal completion and screams rather loud if
they don't arrive in time. Given that we need a real piece of hw to
talk to anyway this is probably as good as it gets.
v2: Don't check the dp aux channel bits on i965 machines, they have a
different meaning there. Yay for reusing bits at will! Spotted by
Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!
For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.
The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.
v2: Drop the _HOTPLUG, it isn't (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Pipe underrun can't just be enabled, we need some support code like
on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
adjust the output.
v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a per-pipe bit in the master irq control register, so use it.
This allows us to drop the masks for aggregate interrupt bits and be a
bit more explicit in the code. It also removes one indentation level.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hold vertex data in cache until last reference
BDW-A workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW-A workaround
BDW Bug #1899532
v2: WARN on when not using preliminary HW support
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This implements a workaround for PSR dealing with some vblank issue.
WaPsrDPAMaskVBlankInSRD && WaPsrDPRSUnmaskVBlankInSRD
v2: forgot to git add bogus whitespace fix
v3: Update with workaround names.
Use for_each_pipe() and CHICKEN_PIPESL_1(pipe) macro (Ville)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Kill redundant IS_BDW check and remove the copious amount of
uneeded lines added.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fixup from Ben to synchronize the GT mailbox commands.
CC: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has bigger display FIFOs than Haswell. Otherwise the
two are very similar.
v2: Fix FBC WM_LP shift for BDW
v3: Rebase on top of the big Haswell wm rework.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not the same as the Haswell ones.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased onto Paulo's MHz->kHz change.
v3: Rebased on top of the Haswell pc8+ adjustements.
v4: Use the exact 337.5MHz clock, should have been done as part of v2.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And it inherits some bits from the previous TRANS_CONF (aka PIPE_CONF
on previous gens).
v2: Rebase on to of the pipe config bpp handling rework.
v3: Rebased on top of the pipe_config->dither refactoring.
v4: Drop the read-modify-write cycle for PIPEMISC, similarly to how we
now also build up PIPECONF completely ourselves - keeping around
random stuff set by the BIOS just isn't a good idea. I've checked BDW
BSpec and we already set all relevant bits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Legacy PPGTT on GEN8 requires programming 4 PDP registers per ring.
Since all rings are using the same address space with the current code
the logic is simply to program all the tables we've setup for the PPGTT.
v2: Turn on PPGTT in GFX_MODE
v3: v2 was the wrong patch
v4: Resolve conflicts due to patch series reordering.
v5: Squash in fixup from Ben: Use LRI to write PDPs
The docs (and simulator seems to back up) suggest that we can only
program legacy PPGTT PDPs with LRI commands.
v6: Rebase around context differences conflicts.
v7: Use #defines for per ring PDPs. (Damien)
v8: Don't use typede'f private_t.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (up to v3 and v7)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW caching works differently than the previous generations. Instead of
having bits in the PTE which directly control how the page is cached,
the 3 PTE bits PWT PCD and PAT provide an index into a PAT defined by
register 0x40e0. This style of caching is functionally equivalent to how
it works on HSW and before.
v2: Tiny bikeshed as discussed on internal irc.
v3: Squash in patch from Ville to mirror the x86 PAT setup more like
in arch/x86/mm/pat.c. Primarily, the 0th index will be WB, and not
uncached.
v4: Comment for reason to not use a 64b write on the PPAT.
v5: Add a FIXME comment that the caching bits in the PAT registers
might be wrong due to doc confusion.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.
Now the second dword in the command has the upper 16b of the address of
the batchbuffer.
v2: Remove duplicated vfun assignment.
v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>
v4: Make checkpatch happy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
Just enough to make the code not barf...
Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW context sizes varies a bit.
v2: Squash in fixup for the hw context size from Ben.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the connector and pipe passed around, we can now set the backlight
on the right pipe on VLV/BYT.
v2: drop combination mode check for VLV (Jani)
add save/restore code for VLV backlight regs (Jani)
check for existing modulation freq when initializing backlight regs (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67245
Tested-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive. Lowering it can save power, while
raising it is necessary to support high resolution.
Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.
v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
use shifts by 1 for fixed point (Ville)
drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
clock data (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch defines HD-Audio configuration registers and enables display audio
from HDA controller for Valleyview2.
v2: fix missing offset VLV_DISPLAY_BASE
v3: rename patch from 'enable HDMI audio' to 'enable HDA display audio', since
it's for both HDMI and DP audio
v4: use enc_to_dig_port() to get port number, instead of using Haswell specific
function intel_ddi_get_encoder_port()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.
Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).
v2: Apply the suggestions from Damien's review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incorrect definition DPIO_TX3_SWING_CTL4.
From Ville's review: "Based on the specs, the typo meant that HDMI B
ended up using "incorrect" de-emphasis for the TMDS data lanes."
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add comment from Ville's review about the impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
ivb display interrupt handler.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.
v2: Only record BB_STATE for gen4+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Production HSW does not need it. I confirmed this with Art.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All our registers which are written through the MCHBAR are defined
descriptively as an offset to the MCHBAR. We had 3 outliers here.
Convert these as well so all registers which are offsets are MCHBAR can
be easily identified/found within the code.
With this, convert DCLK to also follow this format.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Really simple, and we don't even have working frame numbers.
v2: Actually enable it ...
v3: Review from Ville:
- Unconditionally enable the border in the CRC checksum for
consistency with gen3+.
- Handle the "none" source to be able to disable the CRC machinery
again.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPE_B #define was missing the display mmio offset. Use the
_PIPE_INC macro instead, it's simpler.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit a mess, since with DP/TV outputs we can't use the pipe CRC.
Also, no plane CRCs, so we need to update the basic testcases.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should work down to gen2. The #defines for the interrupt sources are
already there in PIPESTAT and are the same on all gmch platforms for
gen2 up to vlv.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once the machine gets to a certain point in the suspend process, we
expect the GPU to be idle. If it is not, we might corrupt memory.
Empirically (with an early version of this patch) we have seen this is
not the case. We cannot currently explain why the latent GPU writes
occur.
In the technical sense, this patch is a workaround in that we have an
issue we can't explain, and the patch indirectly solves the issue.
However, it's really better than a workaround because we understand why
it works, and it really should be a safe thing to do in all cases.
The noticeable effect other than the debug messages would be an increase
in the suspend time. I have not measure how expensive it actually is.
I think it would be good to spend further time to root cause why we're
seeing these latent writes, but it shouldn't preclude preventing the
fallout.
NOTE: It should be safe (and makes some sense IMO) to also keep the
VALID bit unset on resume when we clear_range(). I've opted not to do
this as properly clearing those bits at some later point would be extra
work.
v2: Fix bugzilla link
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=65496
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59321
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Tested-By: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hw designers decided to change the CRC registers and coalesce them all
into one. Otherwise nothing changed. I've opted for a new hsw_ version
to grab the crc sample since hsw+1 will have the same crc registers,
but different interrupt source registers. So this little helper
function will come handy there.
Also refactor the display error handler with a neat pipe loop.
v2: Use for_each_pipe.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We enable the interrupt unconditionally and only control it
through the enable bit in the CRC control register.
v2: Extract per-platform helpers to compute the register values.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add a new _PIPE_INC macro which takes an base plus increment.
Much less likely to botch the job by missing an s/A/B/ somewhere.
v2: They've moved the bitfield. Argh!
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The HDMI audio expects HDMI pixel clock to be set in the audio
configuration. We've currently just set 0, using 25.2 / 1.001 kHz
frequency, which fails with some modes.
v2: Now with a commit message.
Reference: http://mid.gmane.org/CAGpEb3Ep1LRZETPxHGRfBDqr5Ts2tAc8gCukWwugUf1U5NYv1g@mail.gmail.com
Reference: http://mid.gmane.org/20130206213533.GA16367@hardeman.nu
Reported-by: David Härdeman <david@hardeman.nu>
Reported-by: Jasper Smet <josbeir@gmail.com>
Tested-by: Jasper Smet <josbeir@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are several points in the display pipeline where CRCs can be
computed on the bits flowing there. For instance, it's usually possible
to compute the CRCs of the primary plane, the sprite plane or the CRCs
of the bits after the panel fitter (collectively called pipe CRCs).
v2: Quite a bit of rework here and there (Damien)
Signed-off-by: Shuang He <shuang.he@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Fix intermediate compile file reported by Wu Fengguang's
kernel builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä