Starting with the v1.2 definition of namespace labels, the isetcookie
field is populated and validated for blk-aperture namespaces. This adds
some safety against inadvertent copying of namespace labels from one
DIMM-device to another.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The type_guid refers to the "Address Range Type GUID" for the region
backing a namespace as defined the ACPI NFIT (NVDIMM Firmware Interface
Table). This 'type' identifier specifies an access mechanism for the
given namespace. This capability replaces the confusing usage of the
'NSLABEL_FLAG_LOCAL' flag to indicate a block-aperture-mode namespace.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previously we only honored the lba size for blk-aperture mode
namespaces. For pmem namespaces the lba size was just assumed to be 512.
With the new v1.2 label definition and compatibility with other
operating environments, the ->lbasize property is now respected for pmem
namespaces.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The interleave-set-cookie algorithm is extended to incorporate all the
same components that are used to generate an nvdimm unique-id. For
backwards compatibility we still maintain the old v1.1 definition.
Reported-by: Nicholas Moulin <nicholas.w.moulin@intel.com>
Reported-by: Kaushik Kanetkar <kaushik.a.kanetkar@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In support of improved interoperability between operating systems and pre-boot
environments the Intel proposed NVDIMM Namespace Specification [1], has been
adopted and modified to the the UEFI 2.7 NVDIMM Label Protocol [2].
Update the definitions of the namespace label data structures so that the new
format can be supported alongside the existing label format.
The new specification changes the default label size to 256 bytes, so
everywhere that relied on sizeof(struct nd_namespace_label) must now use the
sizeof_namespace_label() helper.
There should be no functional differences from these changes as the
default is still the v1.1 128-byte format. Future patches will move the
default to the v1.2 definition.
[1]: http://pmem.io/documents/NVDIMM_Namespace_Spec.pdf
[2]: http://www.uefi.org/sites/default/files/resources/UEFI_Spec_2_7.pdf
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The pmem driver has a need to transfer data with a persistent memory
destination and be able to rely on the fact that the destination writes are not
cached. It is sufficient for the writes to be flushed to a cpu-store-buffer
(non-temporal / "movnt" in x86 terms), as we expect userspace to call fsync()
to ensure data-writes have reached a power-fail-safe zone in the platform. The
fsync() triggers a REQ_FUA or REQ_FLUSH to the pmem driver which will turn
around and fence previous writes with an "sfence".
Implement a __copy_from_user_inatomic_flushcache, memcpy_page_flushcache, and
memcpy_flushcache, that guarantee that the destination buffer is not dirty in
the cpu cache on completion. The new copy_from_iter_flushcache and sub-routines
will be used to replace the "pmem api" (include/linux/pmem.h +
arch/x86/include/asm/pmem.h). The availability of copy_from_iter_flushcache()
and memcpy_flushcache() are gated by the CONFIG_ARCH_HAS_UACCESS_FLUSHCACHE
config symbol, and fallback to copy_from_iter_nocache() and plain memcpy()
otherwise.
This is meant to satisfy the concern from Linus that if a driver wants to do
something beyond the normal nocache semantics it should be something private to
that driver [1], and Al's concern that anything uaccess related belongs with
the rest of the uaccess code [2].
The first consumer of this interface is a new 'copy_from_iter' dax operation so
that pmem can inject cache maintenance operations without imposing this
overhead on other dax-capable drivers.
[1]: https://lists.01.org/pipermail/linux-nvdimm/2017-January/008364.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2017-April/009942.html
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Hoist the libnvdimm helper as an inline helper to linux/uuid.h
using an auxiliary const variable uuid_null in lib/uuid.c.
[hch: also add the guid variant. Both do the same but I'd like
to keep casts to a minimum]
The common helper uses the new abstract type uuid_t * instead of
u8 *.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
[hch: added guid_is_null]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
If we had badblocks/poison in the metadata area of a BTT, recreating the
BTT would not clear the poison in all cases, notably the flog area. This
is because rw_bytes will only clear errors if the request being sent
down is 512B aligned and sized.
Make sure that when writing the map and info blocks, the rw_bytes being
sent are of the correct size/alignment. For the flog, instead of doing
the smaller log_entry writes only, first do a 'wipe' of the entire area
by writing zeroes in large enough chunks so that errors get cleared.
Cc: Andy Rudoff <andy.rudoff@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nsio_rw_bytes can clear media errors, but this cannot be done while we
are in an atomic context due to locking within ACPI. From the BTT,
->rw_bytes may be called either from atomic or process context depending
on whether the calls happen during initialization or during IO.
During init, we want to ensure error clearing happens, and the flag
marking process context allows nsio_rw_bytes to do that. When called
during IO, we're in atomic context, and error clearing can be skipped.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Region media error reporting: A libnvdimm region device is the parent
to one or more namespaces. To date, media errors have been reported via
the "badblocks" attribute attached to pmem block devices for namespaces
in "raw" or "memory" mode. Given that namespaces can be in "device-dax"
or "btt-sector" mode this new interface reports media errors
generically, i.e. independent of namespace modes or state. This
subsequently allows userspace tooling to craft "ACPI 6.1 Section
9.20.7.6 Function Index 4 - Clear Uncorrectable Error" requests and
submit them via the ioctl path for NVDIMM root bus devices.
* Introduce 'struct dax_device' and 'struct dax_operations': Prompted by
a request from Linus and feedback from Christoph this allows for dax
capable drivers to publish their own custom dax operations. This fixes
the broken assumption that all dax operations are related to a
persistent memory device, and makes it easier for other architectures
and platforms to add customized persistent memory support.
* 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger memory
controllers to drain write-pending buffers that would otherwise be
flushed automatically by the platform ADR (asynchronous-DRAM-refresh)
mechanism at a power loss event. Support for "locked" DIMMs is included
to prevent namespaces from surfacing when the namespace label data area
is locked. Finally, fixes for various reported deadlocks and crashes,
also tagged for -stable.
* ACPI / nfit driver updates: General updates of the nfit driver to add
DSM command overrides, ACPI 6.1 health state flags support, DSM payload
debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
commmit 565851c972 "device-dax: fix sysfs attribute deadlock"
Tested-by: Yi Zhang <yizhan@redhat.com>
commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=Ox0s
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
Fix failures to create namespaces due to the vmem_altmap not advertising
enough free space to store the memmap.
WARNING: CPU: 15 PID: 8022 at arch/x86/mm/init_64.c:656 arch_add_memory+0xde/0xf0
[..]
Call Trace:
dump_stack+0x63/0x83
__warn+0xcb/0xf0
warn_slowpath_null+0x1d/0x20
arch_add_memory+0xde/0xf0
devm_memremap_pages+0x244/0x440
pmem_attach_disk+0x37e/0x490 [nd_pmem]
nd_pmem_probe+0x7e/0xa0 [nd_pmem]
nvdimm_bus_probe+0x71/0x120 [libnvdimm]
driver_probe_device+0x2bb/0x460
bind_store+0x114/0x160
drv_attr_store+0x25/0x30
In commit 658922e57b "libnvdimm, pfn: fix memmap reservation sizing"
we arranged for the capacity to be allocated, but failed to also update
the 'npfns' parameter. This leads to cases where there is enough
capacity reserved to hold all the allocated sections, but
vmemmap_populate_hugepages() still encounters -ENOMEM from
altmap_alloc_block_buf().
This fix is a stop-gap until we can teach the core memory hotplug
implementation to permit sub-section hotplug.
Cc: <stable@vger.kernel.org>
Fixes: 658922e57b ("libnvdimm, pfn: fix memmap reservation sizing")
Reported-by: Anisha Allada <anisha.allada@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per the latest version of the "NVDIMM DSM Interface Example" [1], the
label data retrieval routine can report a "locked" status. In this case
all regions associated with that DIMM are disabled until the label area
is unlocked. Provide generic libnvdimm enabling for NVDIMMs with label
data area locking capabilities.
[1]: http://pmem.io/documents/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a preparation patch for handling locked nvdimm label regions, a
new concept as introduced by the latest DSM document on pmem.io [1]. A
future patch will leverage nvdimm_set_locked() at DIMM probe time to
flag regions that can not be enabled. There should be no functional
difference resulting from this change.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example-V1.3.pdf
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull x86 mm updates from Ingo Molnar:
"The main x86 MM changes in this cycle were:
- continued native kernel PCID support preparation patches to the TLB
flushing code (Andy Lutomirski)
- various fixes related to 32-bit compat syscall returning address
over 4Gb in applications, launched from 64-bit binaries - motivated
by C/R frameworks such as Virtuozzo. (Dmitry Safonov)
- continued Intel 5-level paging enablement: in particular the
conversion of x86 GUP to the generic GUP code. (Kirill A. Shutemov)
- x86/mpx ABI corner case fixes/enhancements (Joerg Roedel)
- ... plus misc updates, fixes and cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
mm, zone_device: Replace {get, put}_zone_device_page() with a single reference to fix pmem crash
x86/mm: Fix flush_tlb_page() on Xen
x86/mm: Make flush_tlb_mm_range() more predictable
x86/mm: Remove flush_tlb() and flush_tlb_current_task()
x86/vm86/32: Switch to flush_tlb_mm_range() in mark_screen_rdonly()
x86/mm/64: Fix crash in remove_pagetable()
Revert "x86/mm/gup: Switch GUP to the generic get_user_page_fast() implementation"
x86/boot/e820: Remove a redundant self assignment
x86/mm: Fix dump pagetables for 4 levels of page tables
x86/mpx, selftests: Only check bounds-vs-shadow when we keep shadow
x86/mpx: Correctly report do_mpx_bt_fault() failures to user-space
Revert "x86/mm/numa: Remove numa_nodemask_from_meminfo()"
x86/espfix: Add support for 5-level paging
x86/kasan: Extend KASAN to support 5-level paging
x86/mm: Add basic defines/helpers for CONFIG_X86_5LEVEL=y
x86/paravirt: Add 5-level support to the paravirt code
x86/mm: Define virtual memory map for 5-level paging
x86/asm: Remove __VIRTUAL_MASK_SHIFT==47 assert
x86/boot: Detect 5-level paging support
x86/mm/numa: Remove numa_nodemask_from_meminfo()
...
This continues the 4.11 status quo of disabling of error clearing from
the BTT I/O path. Toshi found that even though we have eliminated all
the libnvdimm sources of sleeping-while-atomic triggers, we still have
sleeping operations that will occur in the path to send the ACPI DSM to
the DIMM to clear the error:
BUG: sleeping function called from invalid context at mm/slab.h:432
in_atomic(): 1, irqs_disabled(): 0, pid: 13353, name: dd
Call Trace:
dump_stack+0x86/0xc3
___might_sleep+0x17d/0x250
__might_sleep+0x4a/0x80
__kmalloc+0x1c0/0x2e0
acpi_os_allocate_zeroed+0x2d/0x2f
acpi_evaluate_object+0x59/0x3b1
acpi_evaluate_dsm+0xbd/0x10c
acpi_nfit_ctl+0x1ef/0x7c0 [nfit]
? nsio_rw_bytes+0x152/0x280
nvdimm_clear_poison+0x77/0x140
nsio_rw_bytes+0x18f/0x280
btt_write_pg+0x1d4/0x3d0 [nd_btt]
btt_make_request+0x119/0x2d0 [nd_btt]
A solution for tracking and handling media errors natively in the BTT is
needed.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A debug patch to turn the standard device_lock() into something that
lockdep can analyze yielded the following:
======================================================
[ INFO: possible circular locking dependency detected ]
4.11.0-rc4+ #106 Tainted: G O
-------------------------------------------------------
lt-libndctl/1898 is trying to acquire lock:
(&dev->nvdimm_mutex/3){+.+.+.}, at: [<ffffffffc023c948>] nd_attach_ndns+0x178/0x1b0 [libnvdimm]
but task is already holding lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffc022e0b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
lock_acquire+0xf6/0x1f0
__mutex_lock+0x88/0x980
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_namespace_capacity+0x1b/0x40 [libnvdimm]
nvdimm_namespace_common_probe+0x230/0x510 [libnvdimm]
nd_pmem_probe+0x14/0x180 [nd_pmem]
nvdimm_bus_probe+0xa9/0x260 [libnvdimm]
-> #0 (&dev->nvdimm_mutex/3){+.+.+.}:
__lock_acquire+0x1107/0x1280
lock_acquire+0xf6/0x1f0
__mutex_lock+0x88/0x980
mutex_lock_nested+0x1b/0x20
nd_attach_ndns+0x178/0x1b0 [libnvdimm]
nd_namespace_store+0x308/0x3c0 [libnvdimm]
namespace_store+0x87/0x220 [libnvdimm]
In this case '&dev->nvdimm_mutex/3' mirrors '&dev->mutex'.
Fix this by replacing the use of device_lock() with nvdimm_bus_lock() to protect
nd_{attach,detach}_ndns() operations.
Cc: <stable@vger.kernel.org>
Fixes: 8c2f7e8658 ("libnvdimm: infrastructure for btt devices")
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The x86 conversion to the generic GUP code included a small change which causes
crashes and data corruption in the pmem code - not good.
The root cause is that the /dev/pmem driver code implicitly relies on the x86
get_user_pages() implementation doing a get_page() on the page refcount, because
get_page() does a get_zone_device_page() which properly refcounts pmem's separate
page struct arrays that are not present in the regular page struct structures.
(The pmem driver does this because it can cover huge memory areas.)
But the x86 conversion to the generic GUP code changed the get_page() to
page_cache_get_speculative() which is faster but doesn't do the
get_zone_device_page() call the pmem code relies on.
One way to solve the regression would be to change the generic GUP code to use
get_page(), but that would slow things down a bit and punish other generic-GUP
using architectures for an x86-ism they did not care about. (Arguably the pmem
driver was probably not working reliably for them: but nvdimm is an Intel
feature, so non-x86 exposure is probably still limited.)
So restructure the pmem code's interface with the MM instead: get rid of the
get/put_zone_device_page() distinction, integrate put_zone_device_page() into
__put_page() and and restructure the pmem completion-wait and teardown machinery:
Kirill points out that the calls to {get,put}_dev_pagemap() can be
removed from the mm fast path if we take a single get_dev_pagemap()
reference to signify that the page is alive and use the final put of the
page to drop that reference.
This does require some care to make sure that any waits for the
percpu_ref to drop to zero occur *after* devm_memremap_page_release(),
since it now maintains its own elevated reference.
This speeds up things while also making the pmem refcounting more robust going
forward.
Suggested-by: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/149339998297.24933.1129582806028305912.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Toshi noticed that the new support for a region-level badblocks missed
the case where errors are cleared due to BTT I/O.
An initial attempt to fix this ran into a "sleeping while atomic"
warning due to taking the nvdimm_bus_lock() in the BTT I/O path to
satisfy the locking requirements of __nvdimm_bus_badblocks_clear().
However, that lock is not needed since we are not acting on any data that
is subject to change under that lock. The badblocks instance has its own
internal lock to handle mutations of the error list.
So, in order to make it clear that we are just acting on region devices,
rename __nvdimm_bus_badblocks_clear() to nvdimm_clear_badblocks_regions().
Eliminate the lock and consolidate all support routines for the new
nvdimm_account_cleared_poison() in drivers/nvdimm/bus.c. Finally, to the
opportunity to cleanup to some unnecessary casts, make the calling
convention of nvdimm_clear_badblocks_regions() clearer by replacing struct
resource with the minimal struct clear_badblocks_context, and use the
DEVICE_ATTR macro.
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ND_CMD_CLEAR_ERROR command returns 'clear_err.cleared', the length
of error actually cleared, which may be smaller than its requested
'len'.
Change nvdimm_clear_poison() to call nvdimm_forget_poison() with
'clear_err.cleared' when this value is valid.
Cc: <stable@vger.kernel.org>
Fixes: e046114af5 ("libnvdimm: clear the internal poison_list when clearing badblocks")
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following BUG was observed when nd_pmem_notify() was called
for a BTT device. The use of a pmem_device pointer is not valid
with BTT.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: nd_pmem_notify+0x30/0xf0 [nd_pmem]
Call Trace:
nd_device_notify+0x40/0x50
child_notify+0x10/0x20
device_for_each_child+0x50/0x90
nd_region_notify+0x20/0x30
nd_device_notify+0x40/0x50
nvdimm_region_notify+0x27/0x30
acpi_nfit_scrub+0x341/0x590 [nfit]
process_one_work+0x197/0x450
worker_thread+0x4e/0x4a0
kthread+0x109/0x140
Fix nd_pmem_notify() by setting nd_region and badblocks pointers
properly for BTT.
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 719994660c ("libnvdimm: async notification support")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The nvdimm_flush() mechanism helps to reduce the impact of an ADR
(asynchronous-dimm-refresh) failure. The ADR mechanism handles flushing
platform WPQ (write-pending-queue) buffers when power is removed. The
nvdimm_flush() mechanism performs that same function on-demand.
When a pmem namespace is associated with a block device, an
nvdimm_flush() is triggered with every block-layer REQ_FUA, or REQ_FLUSH
request. These requests are typically associated with filesystem
metadata updates. However, when a namespace is in device-dax mode,
userspace (think database metadata) needs another path to perform the
same flushing. In other words this is not required to make data
persistent, but in the case of metadata it allows for a smaller failure
domain in the unlikely event of an ADR failure.
The new 'deep_flush' attribute is visible when the individual DIMMs
backing a given interleave-set are described by platform firmware. In
ACPI terms this is "NVDIMM Region Mapping Structures" and associated
"Flush Hint Address Structures". Reads return "1" if the region supports
triggering WPQ flushes on all DIMMs. Reads return "0" the flush
operation is a platform nop, and in that case the attribute is
read-only.
Why sysfs and not an ioctl? An ioctl requires establishing a new
ioctl function number space for device-dax. Given that this would be
called on a device-dax fd an application could be forgiven for
accidentally calling this on a filesystem-dax fd. Placing this interface
in libnvdimm sysfs removes that potential for collision with a
filesystem ioctl, and it keeps ioctls out of the generic device-dax
implementation.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nvdimm_clear_poison() expects a physical address, not an offset.
Fix nsio_rw_bytes() to call nvdimm_clear_poison() with a physical
address.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
memcpy_from_pmem() maps directly to memcpy_mcsafe(). The wrapper
serves no real benefit aside from affording a more generic function name
than the x86-specific 'mcsafe'. However this would not be the first time
that x86 terminology leaked into the global namespace. For lack of
better name, just use memcpy_mcsafe() directly.
This conversion also catches a place where we should have been using
plain memcpy, acpi_nfit_blk_single_io().
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all the producers and consumers of dax interfaces have been
converted to using dax_operations on a dax_device, remove the block
device direct_access enabling.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case where a dimm does not have any associated flush hints the
ndrd->flush_wpq array may be uninitialized leading to crashes with the
following signature:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: region_visible+0x10f/0x160 [libnvdimm]
Call Trace:
internal_create_group+0xbe/0x2f0
sysfs_create_groups+0x40/0x80
device_add+0x2d8/0x650
nd_async_device_register+0x12/0x40 [libnvdimm]
async_run_entry_fn+0x39/0x170
process_one_work+0x212/0x6c0
? process_one_work+0x197/0x6c0
worker_thread+0x4e/0x4a0
kthread+0x10c/0x140
? process_one_work+0x6c0/0x6c0
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x31/0x40
Cc: <stable@vger.kernel.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Fixes: f284a4f237 ("libnvdimm: introduce nvdimm_flush() and nvdimm_has_flush()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Setup a dax_device to have the same lifetime as the pmem block device
and add a ->direct_access() method that is equivalent to
pmem_direct_access(). Once fs/dax.c has been converted to use
dax_operations the old pmem_direct_access() will be removed.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit 4aa5615e08 "libnvdimm: band aid btt vs clear
poison locking".
Now that poison list locking has been converted to a spinlock and poison
list entry allocation during i/o has been converted to GFP_NOWAIT,
revert the band-aid that disabled error clearing from btt i/o.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.
c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
A spinlock is introduced to protect the poison list. This allows us to not
having to acquire the reconfig_mutex for touching the poison list. The
add_poison() function has been broken out into two helper functions. One to
allocate the poison entry and the other to apppend the entry. This allows us
to unlock the poison_lock in non-I/O path and continue to be able to allocate
the poison entry with GFP_KERNEL. We will use GFP_NOWAIT in the I/O path in
order to satisfy being in atomic context.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Providing mechanism to clear poison list via the ndctl ND_CMD_CLEAR_ERROR
call. We will update the poison list and also the badblocks at region level
if the region is in dax mode or in pmem mode and not active. In other
words we force badblocks to be cleared through write requests if the
address is currently accessed through a block device, otherwise it can
only be done via the ioctl+dsm path.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding sysfs attribute in order to export the physical address of the
region. This is for supporting of user app poison clear via
ND_IOCTL_CLEAR_ERROR.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
badblocks sysfs file will be export at region level. When nvdimm event
notifier happens for NVDIMM_REVALIATE_POISON, the badblocks in the
region will be updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
As a minimal fix, disable error clearing when the BTT is enabled for the
namespace. For the final fix a larger rework of the poison list locking
is needed.
Note that this is not a problem in the blk case since that path never
calls nvdimm_clear_poison().
Cc: <stable@vger.kernel.org>
Fixes: 82bf1037f2 ("libnvdimm: check and clear poison before writing to pmem")
Cc: Dave Jiang <dave.jiang@intel.com>
[jeff: dynamically disable error clearing in the btt case]
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Holding the reconfig_mutex over a potential userspace fault sets up a
lockdep dependency chain between filesystem-DAX and the libnvdimm ioctl
path. Move the user access outside of the lock.
[ INFO: possible circular locking dependency detected ]
4.11.0-rc3+ #13 Tainted: G W O
-------------------------------------------------------
fallocate/16656 is trying to acquire lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffa00080b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff813b4944>] start_this_handle+0x104/0x460
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (jbd2_handle){++++..}:
lock_acquire+0xbd/0x200
start_this_handle+0x16a/0x460
jbd2__journal_start+0xe9/0x2d0
__ext4_journal_start_sb+0x89/0x1c0
ext4_dirty_inode+0x32/0x70
__mark_inode_dirty+0x235/0x670
generic_update_time+0x87/0xd0
touch_atime+0xa9/0xd0
ext4_file_mmap+0x90/0xb0
mmap_region+0x370/0x5b0
do_mmap+0x415/0x4f0
vm_mmap_pgoff+0xd7/0x120
SyS_mmap_pgoff+0x1c5/0x290
SyS_mmap+0x22/0x30
entry_SYSCALL_64_fastpath+0x1f/0xc2
-> #1 (&mm->mmap_sem){++++++}:
lock_acquire+0xbd/0x200
__might_fault+0x70/0xa0
__nd_ioctl+0x683/0x720 [libnvdimm]
nvdimm_ioctl+0x8b/0xe0 [libnvdimm]
do_vfs_ioctl+0xa8/0x740
SyS_ioctl+0x79/0x90
do_syscall_64+0x6c/0x200
return_from_SYSCALL_64+0x0/0x7a
-> #0 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
__lock_acquire+0x16b6/0x1730
lock_acquire+0xbd/0x200
__mutex_lock+0x88/0x9b0
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
pmem_do_bvec+0x1c2/0x2b0 [nd_pmem]
pmem_make_request+0xf9/0x270 [nd_pmem]
generic_make_request+0x118/0x3b0
submit_bio+0x75/0x150
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit a1f3e4d6a0 "libnvdimm, region: update nd_region_available_dpa()
for multi-pmem support" reworked blk dpa (DIMM Physical Address)
accounting to comprehend multiple pmem namespace allocations aliasing
with a given blk-dpa range.
The following call trace is a result of failing to account for allocated
blk capacity.
WARNING: CPU: 1 PID: 2433 at tools/testing/nvdimm/../../../drivers/nvdimm/names
4 size_store+0x6f3/0x930 [libnvdimm]
nd_region region5: allocation underrun: 0x0 of 0x1000000 bytes
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_fmt+0x5f/0x80
size_store+0x6f3/0x930 [libnvdimm]
dev_attr_store+0x18/0x30
If a given blk-dpa allocation does not alias with any pmem ranges then
the full allocation should be accounted as busy space, not the size of
the current pmem contribution to the region.
The thinkos that led to this confusion was not realizing that the struct
resource management is already guaranteeing no collisions between pmem
allocations and blk allocations on the same dimm. Also, we do not try to
support blk allocations in aliased pmem holes.
This patch also fixes a case where the available blk goes negative.
Cc: <stable@vger.kernel.org>
Fixes: a1f3e4d6a0 ("libnvdimm, region: update nd_region_available_dpa() for multi-pmem support").
Reported-by: Dariusz Dokupil <dariusz.dokupil@intel.com>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The interleave-set cookie is a sum that sanity checks the composition of
an interleave set has not changed from when the namespace was initially
created. The checksum is calculated by sorting the DIMMs by their
location in the interleave-set. The comparison for the sort must be
64-bit wide, not byte-by-byte as performed by memcmp() in the broken
case.
Fix the implementation to accept correct cookie values in addition to
the Linux "memcmp" order cookies, but only allow correct cookies to be
generated going forward. It does mean that namespaces created by
third-party-tooling, or created by newer kernels with this fix, will not
validate on older kernels. However, there are a couple mitigating
conditions:
1/ platforms with namespace-label capable NVDIMMs are not widely
available.
2/ interleave-sets with a single-dimm are by definition not affected
(nothing to sort). This covers the QEMU-KVM NVDIMM emulation case.
The cookie stored in the namespace label will be fixed by any write the
namespace label, the most straightforward way to achieve this is to
write to the "alt_name" attribute of a namespace in sysfs.
Cc: <stable@vger.kernel.org>
Fixes: eaf961536e ("libnvdimm, nfit: add interleave-set state-tracking infrastructure")
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When vmemmap_populate() allocates space for the memmap it does so in 2MB
sized chunks. The libnvdimm-pfn driver incorrectly accounts for this
when the alignment of the device is set to 4K. When this happens we
trigger memory allocation failures in altmap_alloc_block_buf() and
trigger warnings of the form:
WARNING: CPU: 0 PID: 3376 at arch/x86/mm/init_64.c:656 arch_add_memory+0xe4/0xf0
[..]
Call Trace:
dump_stack+0x86/0xc3
__warn+0xcb/0xf0
warn_slowpath_null+0x1d/0x20
arch_add_memory+0xe4/0xf0
devm_memremap_pages+0x29b/0x4e0
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute, default to HPAGE_SIZE")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given that the naming of pmem devices changes from the pmemX form to the
pmemX.Y form when namespace id is greater than 0, arrange for namespaces
with id-0 to be exempt from deletion. Otherwise a simple reconfiguration
of an existing namespace to a new mode results in a name change of the
resulting block device:
# ndctl list --namespace=namespace1.0
{
"dev":"namespace1.0",
"mode":"raw",
"size":2147483648,
"uuid":"3dadf3dc-89b9-4b24-b20e-abc8a4707ce3",
"blockdev":"pmem1"
}
# ndctl create-namespace --reconfig=namespace1.0 --mode=memory --force
{
"dev":"namespace1.1",
"mode":"memory",
"size":2111832064,
"uuid":"7b4a6341-7318-4219-a02c-fb57c0bbf613",
"blockdev":"pmem1.1"
}
This change does require tooling changes to explicitly look for
namespaceX.0 if the seed has already advanced to another namespace.
Cc: <stable@vger.kernel.org>
Fixes: 98a29c39dc ("libnvdimm, namespace: allow creation of multiple pmem-namespaces per region")
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to declaration of device_type structure.
File size before:
text data bss dec hex filename
19278 3199 16 22493 57dd nvdimm/namespace_devs.o
File size after:
text data bss dec hex filename
19929 3160 16 23105 5a41 nvdimm/namespace_devs.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 98a29c39dc ("libnvdimm, namespace: allow creation of multiple
pmem-namespaces per region") added support for establishing additional
pmem namespace beyond the seed device, similar to blk namespaces.
However, it neglected to delete the namespace when the size is set to
zero.
Fixes: 98a29c39dc ("libnvdimm, namespace: allow creation of multiple pmem-namespaces per region")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The read_pmem() function uses memcpy_mcsafe() on x86 where an EFAULT
error code indicates a failed read. Block I/O should use EIO to
indicate failure. Other pmem code paths (like bad blocks) already use
EIO so let's be consistent.
This fixes compatibility with consumers like btrfs that try to parse the
specific error code rather than treat all errors the same.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* Dynamic label support: To date namespace label support has been
limited to disambiguating cases where PMEM (direct load/store) and BLK
(mmio aperture) accessed-capacity alias on the same DIMM. Since 4.9 added
support for multiple namespaces per PMEM-region there is value to
support namespace labels even in the non-aliasing case. The presence of
a valid namespace index block force-enables label support when the
kernel would otherwise rely on region boundaries, and permits the region
to be sub-divided.
* Handle media errors in namespace metadata: Complement the error
handling for media errors in namespace data areas with support for
clearing errors on writes, and downgrading potential machine-check
exceptions to simple i/o errors on read.
* Device-DAX region attributes: Add 'align', 'id', and 'size' as
attributes for device-dax regions. In particular this enables userspace
tooling to generically size memory mapping and i/o operations. Prevent
userspace from growing assumptions / dependencies about the parent
device topology for a dax region. A libnvdimm namespace may not always
be the parent device of a dax region.
* Various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=YWfP
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The libnvdimm pull request is relatively small this time around due to
some development topics being deferred to 4.11.
As for this pull request the bulk of it has been in -next for several
releases leading to one late fix being added (commit 868f036fee
("libnvdimm: fix mishandled nvdimm_clear_poison() return value")). It
has received a build success notification from the 0day-kbuild robot
and passes the latest libnvdimm unit tests.
Summary:
- Dynamic label support: To date namespace label support has been
limited to disambiguating cases where PMEM (direct load/store) and
BLK (mmio aperture) accessed-capacity alias on the same DIMM. Since
4.9 added support for multiple namespaces per PMEM-region there is
value to support namespace labels even in the non-aliasing case.
The presence of a valid namespace index block force-enables label
support when the kernel would otherwise rely on region boundaries,
and permits the region to be sub-divided.
- Handle media errors in namespace metadata: Complement the error
handling for media errors in namespace data areas with support for
clearing errors on writes, and downgrading potential machine-check
exceptions to simple i/o errors on read.
- Device-DAX region attributes: Add 'align', 'id', and 'size' as
attributes for device-dax regions. In particular this enables
userspace tooling to generically size memory mapping and i/o
operations. Prevent userspace from growing assumptions /
dependencies about the parent device topology for a dax region. A
libnvdimm namespace may not always be the parent device of a dax
region.
- Various cleanups and small fixes"
* tag 'libnvdimm-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: add region 'id', 'size', and 'align' attributes
libnvdimm: fix mishandled nvdimm_clear_poison() return value
libnvdimm: replace mutex_is_locked() warnings with lockdep_assert_held
libnvdimm, pfn: fix align attribute
libnvdimm, e820: use module_platform_driver
libnvdimm, namespace: use octal for permissions
libnvdimm, namespace: avoid multiple sector calculations
libnvdimm: remove else after return in nsio_rw_bytes()
libnvdimm, namespace: fix the type of name variable
libnvdimm: use consistent naming for request_mem_region()
nvdimm: use the right length of "pmem"
libnvdimm: check and clear poison before writing to pmem
tools/testing/nvdimm: dynamic label support
libnvdimm: allow a platform to force enable label support
libnvdimm: use generic iostat interfaces
Colin, via static analysis, reports that the length could be negative
from nvdimm_clear_poison() in the error case. There was a similar
problem with commit 0a3f27b9a6 "libnvdimm, namespace: avoid multiple
sector calculations" that I noticed when merging the for-4.10/libnvdimm
topic branch into libnvdimm-for-next, but I missed this one. Fix both of
them to the following procedure:
* if we clear a block's worth of media, clear that many blocks in
badblocks
* if we clear less than the requested size of the transfer return an
error
* always invalidate cache after any non-error / non-zero
nvdimm_clear_poison result
Fixes: 82bf1037f2 ("libnvdimm: check and clear poison before writing to pmem")
Fixes: 0a3f27b9a6 ("libnvdimm, namespace: avoid multiple sector calculations")
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For warnings that should only ever trigger during development and
testing replace WARN statements with lockdep_assert_held. The lockdep
pattern is prevalent, and these paths are are well covered by libnvdimm
unit tests.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
Fix the format specifier so that the attribute can be parsed correctly.
Currently it returns decimal 1000 for a 4096-byte alignment.
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute, default to HPAGE_SIZE")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given ambiguities in the ACPI 6.1 definition of the "Output (Size)"
field of the ARS (Address Range Scrub) Status command, a firmware
implementation may in practice return 0, 4, or 8 to indicate that there
is no output payload to process.
The specification states "Size of Output Buffer in bytes, including this
field.". However, 'Output Buffer' is also the name of the entire
payload, and earlier in the specification it states "Max Query ARS
Status Output Buffer Size: Maximum size of buffer (including the Status
and Extended Status fields)".
Without this fix if the BIOS happens to return 0 it causes memory
corruption as evidenced by this result from the acpi_nfit_ctl() unit
test.
ars_status00000000: 00020000 00000000 ........
BUG: stack guard page was hit at ffffc90001750000 (stack is ffffc9000174c000..ffffc9000174ffff)
kernel stack overflow (page fault): 0000 [#1] SMP DEBUG_PAGEALLOC
task: ffff8803332d2ec0 task.stack: ffffc9000174c000
RIP: 0010:[<ffffffff814cfe72>] [<ffffffff814cfe72>] __memcpy+0x12/0x20
RSP: 0018:ffffc9000174f9a8 EFLAGS: 00010246
RAX: ffffc9000174fab8 RBX: 0000000000000000 RCX: 000000001fffff56
RDX: 0000000000000000 RSI: ffff8803231f5a08 RDI: ffffc90001750000
RBP: ffffc9000174fa88 R08: ffffc9000174fab0 R09: ffff8803231f54b8
R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000003 R15: ffff8803231f54a0
FS: 00007f3a611af640(0000) GS:ffff88033ed00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc90001750000 CR3: 0000000325b20000 CR4: 00000000000406e0
Stack:
ffffffffa00bc60d 0000000000000008 ffffc90000000001 ffffc9000174faac
0000000000000292 ffffffffa00c24e4 ffffffffa00c2914 0000000000000000
0000000000000000 ffffffff00000003 ffff880331ae8ad0 0000000800000246
Call Trace:
[<ffffffffa00bc60d>] ? acpi_nfit_ctl+0x49d/0x750 [nfit]
[<ffffffffa01f4fe0>] nfit_test_probe+0x670/0xb1b [nfit_test]
Cc: <stable@vger.kernel.org>
Fixes: 747ffe11b4 ("libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use module_platform_driver for the e820 driver instead of open-coding it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
According to commit f90774e1fd
("checkpatch: look for symbolic permissions and suggest octal instead")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use sector_t for cleared
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
else after return is not needed.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
[djbw: removed some now unnecessary newlines]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In create_namespace_blk(), the local variable "name" is defined as an
array of NSLABEL_NAME_LEN pointers:
char *name[NSLABEL_NAME_LEN];
This variable is then used in calls to memcpy() and kmemdup() as if it
were char[NSLABEL_NAME_LEN]. Remove the star in the variable definition
to makes it look right.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Here is an example /proc/iomem listing for a system with 2 namespaces,
one in "sector" mode and one in "memory" mode:
1fc000000-2fbffffff : Persistent Memory (legacy)
1fc000000-2fbffffff : namespace1.0
340000000-34fffffff : Persistent Memory
340000000-34fffffff : btt0.1
Here is the corresponding ndctl listing:
# ndctl list
[
{
"dev":"namespace1.0",
"mode":"memory",
"size":4294967296,
"blockdev":"pmem1"
},
{
"dev":"namespace0.0",
"mode":"sector",
"size":267091968,
"uuid":"f7594f86-badb-4592-875f-ded577da2eaf",
"sector_size":4096,
"blockdev":"pmem0s"
}
]
Notice that the ndctl listing is purely in terms of namespace devices,
while the iomem listing leaks the internal "btt0.1" implementation
detail. Given that ndctl requires the namespace device name to change
the mode, for example:
# ndctl create-namespace --reconfig=namespace0.0 --mode=raw --force
...use the namespace name in the iomem listing to keep the claiming
device name consistent across different mode settings.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
In order to test that the name of a resource begins with "pmem", call
strncmp() with 4 as length instead of 3 to match the whole prefix.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We need to clear any poison when we are writing to pmem. The granularity
will be sector size. If it's less then we can't do anything about it
barring corruption.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
[djbw: fixup 0-length write request to succeed]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A bugfix just tried to address a randconfig build problem and introduced
a variant of the same problem: with CONFIG_LIBNVDIMM=y and
CONFIG_NVDIMM_DAX=m, the nvdimm module now fails to link:
drivers/nvdimm/built-in.o: In function `to_nd_device_type':
bus.c:(.text+0x1b5d): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nd_region_notify_driver_action.constprop.2':
region_devs.c:(.text+0x6b6c): undefined reference to `is_nd_dax'
region_devs.c:(.text+0x6b8c): undefined reference to `to_nd_dax'
drivers/nvdimm/built-in.o: In function `nd_region_probe':
region.c:(.text+0x70f3): undefined reference to `nd_dax_create'
drivers/nvdimm/built-in.o: In function `mode_show':
namespace_devs.c:(.text+0xa196): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nvdimm_namespace_common_probe':
(.text+0xa55f): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nvdimm_namespace_common_probe':
(.text+0xa56e): undefined reference to `to_nd_dax'
This reverts the earlier fix, making NVDIMM_DAX a 'bool' option again
as it should be (it gets linked into the libnvdimm module). To fix
the original problem, I'm adding a dependency on LIBNVDIMM to
DEV_DAX_PMEM, which ensures we can't have that one built-in if the
rest is a module.
Fixes: 4e65e9381c ("/dev/dax: fix Kconfig dependency build breakage")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ACPI Clear Uncorrectable Error DSM function may fail or may be
unsupported on a platform. pmem_clear_poison() returns without clearing
badblocks in such cases. This failure is detected at the next read
(-EIO).
This behavior can lead to an issue when user keeps writing but does not
read immediately. For instance, flight recorder file may be only read
when it is necessary for troubleshooting.
Change pmem_do_bvec() and pmem_clear_poison() to return -EIO so that
filesystem can log an error message on a write error.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If the kcalloc() fails then "devs" can be NULL and we dereference it
checking "devs[i]".
Fixes: 1b40e09a12 ('libnvdimm: blk labels and namespace instantiation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Platforms like QEMU-KVM implement an NFIT table and label DSMs.
However, since that environment does not define an aliased
configuration, the labels are currently ignored and the kernel registers
a single full-sized pmem-namespace per region. Now that the kernel
supports sub-divisions of pmem regions the labels have a purpose.
Arrange for the labels to be honored when we find an existing / valid
namespace index block.
Cc: <qemu-devel@nongnu.org>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nd_iostat_start() and nd_iostat_end() implement the same functionality
that generic_start_io_acct() and generic_end_io_acct() already provide.
Change nd_iostat_start() and nd_iostat_end() to call the generic iostat
interfaces. There is no change in the nd interfaces.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The function dax_pmem_probe() in drivers/dax/pmem.c is compiled under the
CONFIG_DEV_DAX_PMEM tri-state config option. This config option currently
only depends on CONFIG_NVDIMM_DAX, a bool, which means that the following
configuration is possible:
CONFIG_LIBNVDIMM=m
...
CONFIG_NVDIMM_DAX=y
CONFIG_DEV_DAX=y
CONFIG_DEV_DAX_PMEM=y
With this config LIBNVDIMM is compiled as a module with NVDIMM_DAX=y just
meaning that we will compile drivers/nvdimm/dax_devs.c into that module.
However, dax_pmem_probe() depends on several symbols defined in
drivers/nvdimm/dax_devs.c, which results in the following build errors:
drivers/built-in.o: In function `dax_pmem_probe':
linux/drivers/dax/pmem.c:70: undefined reference to `to_nd_dax'
linux/drivers/dax/pmem.c:74: undefined reference to
`nvdimm_namespace_common_probe'
linux/drivers/dax/pmem.c:80: undefined reference to `devm_nsio_enable'
linux/drivers/dax/pmem.c:81: undefined reference to `nvdimm_setup_pfn'
linux/drivers/dax/pmem.c:84: undefined reference to `devm_nsio_disable'
linux/drivers/dax/pmem.c:122: undefined reference to `to_nd_region'
drivers/built-in.o: In function `dax_pmem_init':
linux/drivers/dax/pmem.c:147: undefined reference to `__nd_driver_register'
Fix this by making NVDIMM_DAX a tristate. DEV_DAX_PMEM depends on
NVDIMM_DAX which depends on LIBNVDIMM. Since they are all now tristates,
if LIBNVDIMM is built as a kernel module DEV_DAX_PMEM will be as well.
This prevents dax_devs.c from being built as a built-in while its
dependencies are in the libnvdimm.ko module.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to BLK regions, publish new seed namespace devices to allow
unused PMEM region capacity to be consumed by additional namespaces.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the rest of the infrastructure has been converted to handle
multi-pmem configurations, lift the artificial barrier at scan time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Short-circuit doomed-to-fail label validation attempts by skipping
labels that are outside the given region. For example a DIMM that has
multiple PMEM regions will waste time attempting to create namespaces
only to find that the interleave-set-cookie does not validate, e.g.:
nd_region region6: invalid cookie in label: 73e608dc-47b9-4b2a-b5c7-2d55a32e0c2
Similar to how we skip BLK labels when performing PMEM validation we can
skip out-of-range labels early.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that we have nd_region_available_dpa() able to handle the presence
of multiple PMEM allocations in aliased PMEM regions, reuse that same
infrastructure to track allocations from free space. In particular
handle allocating from an aliased PMEM region in the case where there
are dis-contiguous holes. The allocation for BLK and PMEM are
documented in the space_valid() helper:
BLK-space is valid as long as it does not precede a PMEM
allocation in a given region. PMEM-space must be contiguous
and adjacent to an existing existing allocation (if one
exists).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instead of assuming that there will only ever be one allocated range at
the start of the region, account for additional namespaces that might
start at an offset from the region base.
After this change pmem namespaces now have a reason to carry an array of
resources similar to blk. Unifying the resource tracking infrastructure
in nd_namespace_common is a future cleanup candidate.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pmem devices are currently named /dev/pmem<region-index>. Preserve the
naming of the 0th device, but add a ".<namespace-index>" for other
devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The free dpa (dimm-physical-address) space calculation reports how much
free space is available with consideration for aliased BLK + PMEM
regions. Recall that BLK capacity is allocated from high addresses and
PMEM is allocated from low addresses in their respective regions.
nd_region_available_dpa() accounts for the fact that the largest
encroachment (lowest starting address) into PMEM capacity by a BLK
allocation limits the available capacity to that point, regardless if
there is BLK allocation hole at a higher address. Similarly, for the
multi-pmem case we need to track the largest encroachment (highest
ending address) of a PMEM allocation in BLK capacity regardless of
whether there is an allocation hole that a BLK allocation could fill at
a lower address.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add more determinism to initial namespace device-name assignments by
sorting the namespaces by starting dpa.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If label scanning finds multiple valid pmem namespaces allow them to be
surfaced rather than fail namespace scanning. Support for creating
multiple namespaces per region is saved for a later patch.
Note that this adds some new error messages to clarify which of the pmem
namespaces in the set are potentially impacted by invalid labels.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for allowing multiple namespace per pmem region, unify
blk and pmem label scanning. Given that blk regions already support
multiple namespaces, teaching that path how to do pmem namespace
scanning is an incremental step towards multiple pmem namespace support.
This should be functionally equivalent to the previous state in that
stops after finding the first valid pmem label set.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ability to translate a generic struct device pointer into a
namespace uuid is a useful utility as we go to unify the blk and pmem
label scanning paths.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for enabling multiple namespaces per pmem region, convert
the label tracking to use a linked list. In particular this will allow
select_pmem_id() to move labels from the unvalidated state to the
validated state. Currently we only track one validated set per-region.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Before we add more libnvdimm-private fields to nd_mapping make it clear
which parameters are input vs libnvdimm internals. Use struct
nd_mapping_desc instead of struct nd_mapping in nd_region_desc and make
struct nd_mapping private to libnvdimm.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Existing implemenetation writes to all the flush hint addresses for a
given ND region. This is not necessary as the flushes are per imc and
not per DIMM. Search the mappings and clear out the duplicates at init
to avoid multiple flush to the same imc.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nvdimm_clear_poison cleared the user-visible badblocks, and sent
commands to the NVDIMM to clear the areas marked as 'poison', but it
neglected to clear the same areas from the internal poison_list which is
used to marshal ARS results before sorting them by namespace. As a
result, once on-demand ARS functionality was added:
37b137f nfit, libnvdimm: allow an ARS scrub to be triggered on demand
A scrub triggered from either sysfs or an MCE was found to be adding
stale entries that had been cleared from gendisk->badblocks, but were
still present in nvdimm_bus->poison_list. Additionally, the stale entries
could be triggered into producing stale disk->badblocks by simply disabling
and re-enabling the namespace or region.
This adds the missing step of clearing poison_list entries when clearing
poison, so that it is always in sync with badblocks.
Fixes: 37b137f ("nfit, libnvdimm: allow an ARS scrub to be triggered on demand")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pmem_do_bvec used to kmap_atomic at the begin, and only unmap at the
end. Things like nvdimm_clear_poison may want to do nvdimm subsystem
bookkeeping operations that may involve taking locks or doing memory
allocations, and we can't do that from the atomic context. Reduce the
atomic context to just what needs it - the memcpy to/from pmem.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The definition of the flush hint table as:
void __iomem *flush_wpq[0][0];
...passed the unit test, but is broken as flush_wpq[0][1] and
flush_wpq[1][0] refer to the same entry. Fix this to use a helper that
calculates a slot in the table based on the geometry of flush hints in
the region. This is important to get right since virtualization
solutions use this mechanism to trigger hypervisor flushes to platform
persistence.
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If platform firmware fails to populate unique / non-zero serial number
data for each nvdimm in an interleave-set it may cause pmem region
initialization to fail. Add a debug message for this case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The internal alloc_nvdimm_map() helper might fail, particularly if the
memory region is already busy. Report request_mem_region() failures and
check for the failure.
Reported-by: Ryan Chen <ryan.chan105@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nd_activate_region() iomaps any hint addresses required when activating
a region. To prevent duplicate mappings it checks the PFN of the hint to
be mapped against the PFNs of the already mapped hints. Unfortunately it
doesn't convert the PFN back into a physical address before passing it
to devm_nvdimm_ioremap(). Instead it applies PHYS_PFN a second time
which ends about as well as you would imagine.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
'ndctl list --buses --dimms' does not list any NVDIMM-Ns since
they are considered as idle. ndctl checks if any driver is
attached to nmem device. nvdimm_probe() always fails in
nvdimm_init_nsarea() since NVDIMM-Ns do not implement optinal
ND_CMD_GET_CONFIG_DATA command.
Change nvdimm_probe() to accept the case that the CONFIG_DATA
command is not implemented for NVDIMM-Ns. The driver attaches
without ndd, which keeps it no-op to the device.
Reported-by: Brian Boylston <brian.boylston@hpe.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per "ACPI 6.1 Section 9.20.3" NVDIMM devices, children of the ACPI0012
NVDIMM Root device, can receive health event notifications.
Given that these devices are precluded from registering a notification
handler via acpi_driver.acpi_device_ops (due to no _HID), we use
acpi_install_notify_handler() directly. The registered handler,
acpi_nvdimm_notify(), triggers a poll(2) event on the nmemX/nfit/flags
sysfs attribute when a health event notification is received.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To be consistent with other namespaces, expose a 'size' attribute for
BTT devices also.
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit abf545484d changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a8 ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
The __nd_device_register() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Normally, an ARS (Address Range Scrub) only happens at
boot/initialization time. There can however arise situations where a
bus-wide rescan is needed - notably, in the case of discovering a latent
media error, we should do a full rescan to figure out what other sectors
are bad, and thus potentially avoid triggering an mce on them in the
future. Also provide a sysfs trigger to start a bus-wide scrub.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent effort to add a new nvdimm bus provider attribute highlighted a
race between interrogating nvdimm_bus->nd_desc and nvdimm_bus tear down.
The typical way to handle these races is to take the device_lock() in
the attribute method and validate that the device is still active. In
order for a device to be 'active' it needs to be associated with a
driver. So, we create the small boilerplate for a driver and register
nvdimm_bus devices on the 'nvdimm_bus_type' bus.
A result of this change is that ndbusX devices now appear under
/sys/bus/nd/devices. In fact this makes /sys/class/nd somewhat
redundant, but removing that will need to take a long deprecation period
given its use by ndctl binaries in the field.
This change naturally pulls code from drivers/nvdimm/core.c to
drivers/nvdimm/bus.c, so it is a nice code organization clean-up as
well.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prefix the sector number being cleared with a '0x' to make it clear that
this is a hex value.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Let the provider module be explicitly passed in rather than implicitly
assumed by the module that calls nvdimm_bus_register(). This is in
preparation for unifying the nfit and nfit_test driver teardown paths.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently, presence of direct_access() in block_device_operations
indicates support of DAX on its block device. Because
block_device_operations is instantiated with 'const', this DAX
capablity may not be enabled conditinally.
In preparation for supporting DAX to device-mapper devices, add
QUEUE_FLAG_DAX to request_queue flags to advertise their DAX
support. This will allow to set the DAX capability based on how
mapped device is composed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
The __pmem address space was meant to annotate codepaths that touch
persistent memory and need to coordinate a call to wmb_pmem(). Now that
wmb_pmem() is gone, there is little need to keep this annotation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nsio_rw_bytes() is used to write info block metadata to the namespace,
so it should trigger a flush after every write. Replace wmb_pmem() with
nvdimm_flush() in this path.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given that nvdimm_flush() has higher overhead than wmb_pmem() (pointer
chasing through nd_region), and that we otherwise assume a platform has
ADR capability when flush hints are not present, move nvdimm_flush() to
REQ_FLUSH context.
Note that we still arrange for nvdimm_flush() to be called even in the
ADR case. We need at least once wmb() fence to push buffered writes in
the cpu out to the ADR protected domain.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the NFIT provides multiple flush hint addresses per-dimm it is
expressing that the platform is capable of processing multiple flush
requests in parallel. There is some fixed cost per flush request, let
the cost be shared in parallel on multiple cpus.
Since there may not be enough flush hint addresses for each cpu to have
one, keep a per-cpu index of the last used hint, hash it with current
pid, and assume that access pattern and scheduler randomness will keep
the flush-hint usage somewhat staggered across cpus.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nvdimm_flush() is a replacement for the x86 'pcommit' instruction. It is
an optional write flushing mechanism that an nvdimm bus can provide for
the pmem driver to consume. In the case of the NFIT nvdimm-bus-provider
nvdimm_flush() is implemented as a series of flush-hint-address [1]
writes to each dimm in the interleave set (region) that backs the
namespace.
The nvdimm_has_flush() routine relies on platform firmware to describe
the flushing capabilities of a platform. It uses the heuristic of
whether an nvdimm bus provider provides flush address data to return a
ternary result:
1: flush addresses defined
0: dimm topology described without flush addresses (assume ADR)
-errno: no topology information, unable to determine flush mechanism
The pmem driver is expected to take the following actions on this ternary
result:
1: nvdimm_flush() in response to REQ_FUA / REQ_FLUSH and shutdown
0: do not set, WC or FUA on the queue, take no further action
-errno: warn and then operate as if nvdimm_has_flush() returned '0'
The caveat of this heuristic is that it can not distinguish the "dimm
does not have flush address" case from the "platform firmware is broken
and failed to describe a flush address". Given we are already
explicitly trusting the NFIT there's not much more we can do beyond
blacklisting broken firmwares if they are ever encountered.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
nd_region device driver data will be used in the namespace i/o path.
Re-order nd_region_remove() to ensure this data stays live across
namespace device removal
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for triggering flushes of a DIMM's writes-posted-queue
(WPQ) via the pmem driver move mapping of flush hint addresses to the
region driver. Since this uses devm_nvdimm_memremap() the flush
addresses will remain mapped while any region to which the dimm belongs
is active.
We need to communicate more information to the nvdimm core to facilitate
this mapping, namely each dimm object now carries an array of flush hint
address resources.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all shared mappings are handled by devm_nvdimm_memremap() we no
longer need nfit_spa_map() nor do we need to trigger a callback to the
bus provider at region disable time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for generically mapping flush hint addresses for both the
BLK and PMEM use case, provide a generic / reference counted mapping
api. Given the fact that a dimm may belong to multiple regions (PMEM
and BLK), the flush hint addresses need to be held valid as long as any
region associated with the dimm is active. This is similar to the
existing BLK-region case where multiple BLK-regions may share an
aperture mapping. Up-level this shared / reference-counted mapping
capability from the nfit driver to a core nvdimm capability.
This eliminates the need for the nd_blk_region.disable() callback. Note
that the removal of nfit_spa_map() and related infrastructure is
deferred to a later patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Initialize struct blk_integrity with 0 as blk_integrity_register() takes the
then unitialized struct blk_integrity::flags and ORs it to the resulting block
integrity structure.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all drivers that specify a ->driverfs_dev have been converted
to device_add_disk(), the pointer can be removed from struct gendisk.
Cc: Jens Axboe <axboe@fb.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently phys_to_pfn_t() is an exported symbol to allow nfit_test to
override it and indicate that nfit_test-pmem is not device-mapped. Now,
we want to enable nfit_test to operate without DMA_CMA and the pmem it
provides will no longer be physically contiguous, i.e. won't be capable
of supporting direct_access requests larger than a page. Make
pmem_direct_access() a weak symbol so that it can be replaced by the
tools/testing/nvdimm/ version, and move phys_to_pfn_t() to a static
inline now that it no longer needs to be overridden.
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The updated ndctl unit tests discovered that if a pfn configuration with
a 4K alignment is read from the namespace, that alignment will be
ignored in favor of the default 2M alignment. The result is that the
configuration will fail initialization with a message like:
dax6.1: bad offset: 0x22000 dax disabled align: 0x200000
Fix this by allowing the alignment read from the info block to override
the default which is 2M not 0 in the autodetect path. This also fixes a
similar problem with the mode and alignment settings silently being
overwritten by the kernel when userspace has changed it. We now will
either overwrite the info block if userspace changes the uuid or fail
and warn if a live setting disagrees with the info block.
Cc: <stable@vger.kernel.org>
Cc: Micah Parrish <micah.parrish@hpe.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prompted by commit 287980e49f "remove lots of IS_ERR_VALUE abuses", I
ran make coccicheck against drivers/nvdimm/ and found that:
if (IS_ERR(x))
return PTR_ERR(x);
return 0;
...can be replaced with PTR_ERR_OR_ZERO().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Clean up needless calls to the action routine by letting
devm_add_action_or_reset() call it automatically. This does cause the
disk to registered and immediately unregistered when a memory allocation
fails, but the block layer should be prepared for such an event.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Until now, dax has been disabled if media errors were found on
any device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition
is page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent reads/writes
would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX related to
zeroing, writeback, and some size checks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6Of
-----END PGP SIGNATURE-----
Merge tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
The ndctl unit tests discovered that the dax enabling omitted updates to
nd_detach_and_reset(). This routine clears device the configuration
when the namespace is detached. Without this clearing userspace may
assume that the device is in the process of being configured by another
agent in the system.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Testing the dax-device autodetect support revealed a probe failure with
the following result:
dax0.1: bad offset: 0x8200000 dax disabled
The original pfn-device implementation inferred the alignment from
ilog2(offset), now that the alignment is explicit the is_power_of_2()
needs replacing with a real sanity check against the recorded alignment.
Otherwise the alignment check is useless in the implicit case and only
the minimum size of the offset matters.
This self-consistency check is further validated by the probe path that
will re-check that the offset is large enough to contain all the
metadata required to enable the device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For autodetecting a previously established dax configuration we need the
info block to indicate block-device vs device-dax mode, and we need to
have the default namespace probe hand-off the configuration to the
dax_pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ida instances allocate some internal memory for ->free_bitmap in
addition to the base 'struct ida'. Use ida_destroy() to release that
memory at module_exit().
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ If a mapping overlaps a bad sector fail the request.
2/ Do not opportunistically report more dax-capable capacity than is
requested when errors present.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[vishal: fix a conflict with system RAM collision patches]
[vishal: add a 'size' parameter to ->direct_access]
[vishal: fix a conflict with DAX alignment check patches]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
The dax_pmem driver was implementing an empty ->remove() method to
satisfy the nvdimm bus driver that unconditionally calls ->remove().
Teach the core bus driver to check if ->remove() is NULL to remove that
requirement.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We want to use the alignment as the allocation and mapping unit.
Previously this information was only useful for establishing the data
offset, but now it is important to remember the granularity for the
later use.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We may want to subdivide a device-dax range into multiple devices so
that each can have separate permissions or naming. Reserve 128K of
label space by default so we have the capability of making allocation
decisions persistent. This reservation is not something we can add
later since it would result in the default size of a device-dax range
changing between kernel versions.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Device DAX is the device-centric analogue of Filesystem DAX
(CONFIG_FS_DAX). It allows persistent memory ranges to be allocated and
mapped without need of an intervening file system. This initial
infrastructure arranges for a libnvdimm pfn-device to be represented as
a different device-type so that it can be attached to a driver other
than the pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I had relied on the kbuild robot for cross build coverage, however it
only builds alpha_defconfig. Switch from HPAGE_SIZE to PMD_SIZE, which
is more widely defined.
Fixes: 658922e57b ("libnvdimm, pfn: fix memmap reservation sizing")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <guenter@roeck-us.net>
Tested-by: Guenter Roeck <guenter@roeck-us.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When configuring a pfn-device instance to allocate the memmap array it
needs to account for the fact that vmemmap_populate_hugepages()
allocates struct page blocks in HPAGE_SIZE chunks. We need to align the
reserved area size to 2MB otherwise arch_add_memory() runs out of memory
while establishing the memmap:
WARNING: CPU: 0 PID: 496 at arch/x86/mm/init_64.c:704 arch_add_memory+0xe7/0xf0
[..]
Call Trace:
[<ffffffff8148bdb3>] dump_stack+0x85/0xc2
[<ffffffff810a749b>] __warn+0xcb/0xf0
[<ffffffff810a75cd>] warn_slowpath_null+0x1d/0x20
[<ffffffff8106a497>] arch_add_memory+0xe7/0xf0
[<ffffffff811d2097>] devm_memremap_pages+0x287/0x450
[<ffffffff811d1ffa>] ? devm_memremap_pages+0x1ea/0x450
[<ffffffffa0000298>] __wrap_devm_memremap_pages+0x58/0x70 [nfit_test_iomap]
[<ffffffffa0047a58>] pmem_attach_disk+0x318/0x420 [nd_pmem]
[<ffffffffa0047bcf>] nd_pmem_probe+0x6f/0x90 [nd_pmem]
[<ffffffffa0009469>] nvdimm_bus_probe+0x69/0x110 [libnvdimm]
[..]
ndbus0: nd_pmem.probe(pfn3.0) = -12
nd_pmem: probe of pfn3.0 failed with error -12
libndctl: ndctl_pfn_enable: pfn3.0: failed to enable
Reported-by: Namratha Kothapalli <namratha.n.kothapalli@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are currently 4 known similar but incompatible definitions of the
command sets that can be sent to an NVDIMM through ACPI. It is also
clear that future platform generations (ACPI or not) will continue to
revise and extend the DIMM command set as new devices and use cases
arrive.
It is obviously untenable to continue to proliferate divergence
of these command definitions, and to that end a standardization process
has begun to provide for a unified specification. However, that leaves a
problem about what to do with this first generation where vendors are
already shipping divergence.
The Linux kernel can support these initial diverged platforms without
giving platform-firmware free reign to continue to diverge and compound
kernel maintenance overhead. The kernel implementation can encourage
standardization in two ways:
1/ Require that any function code that userspace wants to send be
explicitly white-listed in the implementation. For ACPI this means
function codes marked as supported by acpi_check_dsm() may
only be invoked if they appear in the white-list. A function must be
publicly documented before it is added to the white-list.
2/ The above restrictions can be trivially bypassed by using the
"vendor-specific" payload command. However, since vendor-specific
commands are by definition not publicly documented and have the
potential to corrupt the kernel's view of the dimm state, we provide a
toggle to disable vendor-specific operations. Enabling undefined
behavior is a policy decision that can be made by the platform owner
and encourages firmware implementations to choose public over
private command implementations.
Based on an initial patch from Jerry Hoemann
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Clarify the distinction between "commands", the ioctls userspace calls
to request the kernel take some action on a given dimm device, and
"_DSMs", the actual function numbers used in the firmware interface to
the DIMM. _DSMs are ACPI specific whereas commands are Linux kernel
generic.
This is in preparation for breaking the 1:1 implicit relationship
between the kernel ioctl number space and the firmware specific function
numbers.
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The 'host' variable can be killed as it is always the same as the passed
in device.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The devm conversion obviates the need to continue to remember the queue
and disk locally in the driver.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that pmem internals have been disentangled from pfn setup, that code
can move to the core. This is in preparation for adding another user of
the pfn-device capabilities.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for providing an alternative (to block device) access
mechanism to persistent memory, convert pmem_rw_bytes() to
nsio_rw_bytes(). This allows ->rw_bytes() functionality without
requiring a 'struct pmem_device' to be instantiated.
In other words, when ->rw_bytes() is in use i/o is driven through
'struct nd_namespace_io', otherwise it is driven through 'struct
pmem_device' and the block layer. This consolidates the disjoint calls
to devm_exit_badblocks() and devm_memunmap() into a common
devm_nsio_disable() and cleans up the init path to use a unified
pmem_attach_disk() implementation.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The leading '0x' in front of %pa is redundant, also we can just use %pR
to simplify the print statement. The request parameters can be directly
taken from the resource as well.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Register a callback to clean up the request_queue and put the gendisk at
driver disable time.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate the information for issuing i/o to a blk-namespace, and
eliminate some pointer chasing.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I/O errors events have the potential to be a high frequency and a log
message for each event can swamp the system. This message is also
redundant with upper layer error reporting.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Save a pointer chase by storing the driver private data in the
request_queue rather than the gendisk.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Save a pointer chase by storing the driver private data in the
request_queue rather than the gendisk.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Register a callback to clean up the request_queue and put the gendisk at
driver disable time.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pass the device performing the probe so we can use a devm allocation for
the btt superblock.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pass the device performing the probe so we can use a devm allocation for
the pfn superblock.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can derive the common namespace from other information. We also do
not need to cache it because all the usages are in slow paths.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ACPI specification does not specify the state of data after a clear
poison operation. Potential future libnvdimm bus implementations for
other architectures also might not specify or disagree on the state of
data after clear poison. Clarify why we write twice.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Provide simulated SMART data to enable the ndctl implementation of SMART
data retrieval and parsing.
The payload is defined here, "Section 4.1 SMART and Health Info
(Function Index 1)":
http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull libnvdimm fixes from Dan Williams:
"Three fixes, the first two are tagged for -stable:
- The ndctl utility/library gained expanded unit tests illuminating a
long standing bug in the libnvdimm SMART data retrieval
implementation.
It has been broken since its initial implementation, now fixed.
- Another one line fix for the detection of stale info blocks.
Without this change userspace can get into a situation where it is
unable to reconfigure a namespace.
- Fix the badblock initialization path in the presence of the new (in
v4.6-rc1) section alignment workarounds.
Without this change badblocks will be reported at the wrong offset.
These have received a build success report from the kbuild robot and
have appeared in -next with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pfn: fix nvdimm_namespace_add_poison() vs section alignment
libnvdimm, pfn: fix uuid validation
libnvdimm: fix smart data retrieval
When section alignment padding is in effect we need to shift / truncate
the range that is queried for poison by the 'start_pad' or 'end_trunc'
reservations.
It's easiest if we just pass in an adjusted resource range rather than
deriving it from the passed in namespace. With the resource range
resolution pushed out to the caller we can also push the
namespace-to-region lookup to the caller and drop the implicit pmem-type
assumption about the passed in namespace object.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we detect a namespace has a stale info block in the init path, we
should overwrite with the latest configuration. In fact, we already
return -ENODEV when the parent uuid is invalid, the same should be done
for the 'self' uuid. Otherwise we can get into a condition where
userspace is unable to reconfigure the pfn-device without directly /
manually invalidating the info block.
Cc: <stable@vger.kernel.org>
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It appears that smart data retrieval has been broken the since the
initial implementation. Fix the payload size to be 128-bytes per the
specification.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the definition of memcpy_from_pmem() to return 0 or a negative
error code. Implement x86/arch_memcpy_from_pmem() with memcpy_mcsafe().
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull ARM updates from Russell King:
"Another mixture of changes this time around:
- Split XIP linker file from main linker file to make it more
maintainable, and various XIP fixes, and clean up a resulting
macro.
- Decompressor cleanups from Masahiro Yamada
- Avoid printing an error for a missing L2 cache
- Remove some duplicated symbols in System.map, and move
vectors/stubs back into kernel VMA
- Various low priority fixes from Arnd
- Updates to allow bus match functions to return negative errno
values, touching some drivers and the driver core. Greg has acked
these changes.
- Virtualisation platform udpates form Jean-Philippe Brucker.
- Security enhancements from Kees Cook
- Rework some Kconfig dependencies and move PSCI idle management code
out of arch/arm into drivers/firmware/psci.c
- ARM DMA mapping updates, touching media, acked by Mauro.
- Fix places in ARM code which should be using virt_to_idmap() so
that Keystone2 can work.
- Fix Marvell Tauros2 to work again with non-DT boots.
- Provide a delay timer for ARM Orion platforms"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (45 commits)
ARM: 8546/1: dma-mapping: refactor to fix coherent+cma+gfp=0
ARM: 8547/1: dma-mapping: store buffer information
ARM: 8543/1: decompressor: rename suffix_y to compress-y
ARM: 8542/1: decompressor: merge piggy.*.S and simplify Makefile
ARM: 8541/1: decompressor: drop redundant FORCE in Makefile
ARM: 8540/1: decompressor: use clean-files instead of extra-y to clean files
ARM: 8539/1: decompressor: drop more unneeded assignments to "targets"
ARM: 8538/1: decompressor: drop unneeded assignments to "targets"
ARM: 8532/1: uncompress: mark putc as inline
ARM: 8531/1: turn init_new_context into an inline function
ARM: 8530/1: remove VIRT_TO_BUS
ARM: 8537/1: drop unused DEBUG_RODATA from XIP_KERNEL
ARM: 8536/1: mm: hide __start_rodata_section_aligned for non-debug builds
ARM: 8535/1: mm: DEBUG_RODATA makes no sense with XIP_KERNEL
ARM: 8534/1: virt: fix hyp-stub build for pre-ARMv7 CPUs
ARM: make the physical-relative calculation more obvious
ARM: 8512/1: proc-v7.S: Adjust stack address when XIP_KERNEL
ARM: 8411/1: Add default SPARSEMEM settings
ARM: 8503/1: clk_register_clkdev: remove format string interface
ARM: 8529/1: remove 'i' and 'zi' targets
...
If a write is directed at a known bad block perform the following:
1/ write the data
2/ send a clear poison command
3/ invalidate the poison out of the cache hierarchy
Cc: <x86@kernel.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When we enounter a bad block we need to kunmap_atomic() before
returning.
Cc: <stable@vger.kernel.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
alloc_disk(0) does not require or use a ->major number,
all devices are allocated with a major of BLOCK_EXT_MAJOR.
So don't allocate btt_major.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When alloc_disk(0) is used ->major is completely ignored, all devices
are allocated with a "major" of BLOCK_EXT_MAJOR.
So don't allocate nd_blk_major
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When alloc_disk(0) or alloc_disk-node(0, XX) is used, the ->major
number is completely ignored: all devices are allocated with a
major of BLOCK_EXT_MAJOR.
So there is no point allocating pmem_major.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/nvdimm/pmem.c: In function 'nvdimm_namespace_attach_pfn':
drivers/nvdimm/pmem.c:367:3: error: implicit declaration of function
'__phys_to_pfn' [-Werror=implicit-function-declaration]
.base_pfn = __phys_to_pfn(nsio->res.start),
ia64 does not provide __phys_to_pfn(), just use the PHYS_PFN() alias.
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add the boiler-plate for a 'clear error' command based on section
9.20.7.6 "Function Index 4 - Clear Uncorrectable Error" from the ACPI
6.1 specification, and add a reference implementation in nfit_test.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currenty with a raw mode pmem namespace the physical memory address range for
the device can be obtained via /sys/block/pmemX/device/{resource|size}. Add
similar attributes for pfn instances that takes the struct page memmap and
section padding into account.
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
On a platform where 'Persistent Memory' and 'System RAM' are mixed
within a given sparsemem section, trim the namespace and notify about the
sub-optimal alignment.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The altmap for a section-misaligned namespace needs to arrange for the
base_pfn to be section-aligned. As a result the 'reserve' region (pfns
from base that do not have a struct page) must be increased. Otherwise
we trip the altmap validation check in __add_pages:
if (altmap->base_pfn != phys_start_pfn
|| vmem_altmap_offset(altmap) > nr_pages) {
pr_warn_once("memory add fail, invalid altmap\n");
return -EINVAL;
}
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Code attempts to prevent certain IOCTL DSM from being called
when device is opened read only. This security feature can
be trivially overcome by changing the size portion of the
ioctl_command which isn't used.
Check only the _IOC_NR (i.e. the command).
Cc: <stable@vger.kernel.org>
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Change nd_ioctl and nvdimm_ioctl access mode check to use O_RDONLY.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While the nfit driver is issuing address range scrub commands and
reaping the results do not permit an ars_start command issued from
userspace. The scrub thread assumes that all ars completions are for
scrubs initiated by platform firmware at boot, or by the nfit driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Introduce a workqueue that will be used to run address range scrub
asynchronously with the rest of nvdimm device probing.
Userspace still wants notification when probing operations complete, so
introduce a new callback to flush this workqueue when userspace is
awaiting probe completion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for asynchronous address range scrub support add an
ability for the pmem driver to dynamically consume address range scrub
results.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for making poison list retrieval asynchronus to region
registration, add protection for walking and mutating the bus-level
poison list.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The return value from an 'ndctl_fn' reports the command execution
status, i.e. was the command properly formatted and was it successfully
submitted to the bus provider. The new 'cmd_rc' parameter allows the bus
provider to communicate command specific results, translated into
common error codes.
Convert the ARS commands to this scheme to:
1/ Consolidate status reporting
2/ Prepare for for expanding ars unit test cases
3/ Make the implementation more generic
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent bugfix changed pfn_t to always be 64-bit wide, but did not
change the code in pmem.c, which is now broken on 32-bit architectures
as reported by gcc:
In file included from ../drivers/nvdimm/pmem.c:28:0:
drivers/nvdimm/pmem.c: In function 'pmem_alloc':
include/linux/pfn_t.h:15:17: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PFN_DEV (1ULL << (BITS_PER_LONG_LONG - 3))
This changes the intermediate pfn_flags in struct pmem_device to
be 64 bit wide as well, so they can store the flags correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db78c22230 ("mm: fix pfn_t vs highmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The original format of these commands from the "NVDIMM DSM Interface
Example" [1] are superseded by the ACPI 6.1 definition of the "NVDIMM Root
Device _DSMs" [2].
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
[2]: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
"9.20.7 NVDIMM Root Device _DSMs"
Changes include:
1/ New 'restart' fields in ars_status, unfortunately these are
implemented in the middle of the existing definition so this change
is not backwards compatible. The expectation is that shipping
platforms will only ever support the ACPI 6.1 definition.
2/ New status values for ars_start ('busy') and ars_status ('overflow').
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the output length specified in the command to size the receive
buffer rather than the arbitrary 4K limit.
This bug was hiding the fact that the ndctl implementation of
ndctl_bus_cmd_new_ars_status() was not specifying an output buffer size.
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch ensures that existing bus match callbacks don't return
negative values (which might be interpreted as potential errors in the
future) in case of positive match.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the callers of walk_iomem_res() scanning for the
following resources by name to use walk_iomem_res_desc()
instead.
"ACPI Tables"
"ACPI Non-volatile Storage"
"Persistent Memory (legacy)"
"Crash kernel"
Note, the caller of walk_iomem_res() with "GART" will be removed
in a later patch.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Young <dyoung@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chun-Yi <joeyli.kernel@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Lee, Chun-Yi <joeyli.kernel@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Minfei Huang <mnfhuang@gmail.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Takao Indoh <indou.takao@jp.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: kexec@lists.infradead.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/1453841853-11383-15-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This path was missed when turning on the memmap in pmem support. Permit
'pmem' as a valid location for the map.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Correctly display "safe" mode when a btt is established on a e820/memmap
defined pmem namespace.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
get_dev_page() enables paths like get_user_pages() to pin a dynamically
mapped pfn-range (devm_memremap_pages()) while the resulting struct page
objects are in use. Unlike get_page() it may fail if the device is, or
is in the process of being, disabled. While the initial lookup of the
range may be an expensive list walk, the result is cached to speed up
subsequent lookups which are likely to be in the same mapped range.
devm_memremap_pages() now requires a reference counter to be specified
at init time. For pmem this means moving request_queue allocation into
pmem_alloc() so the existing queue usage counter can track "device
pages".
ZONE_DEVICE pages always have an elevated count and will never be on an
lru reclaim list. That space in 'struct page' can be redirected for
other uses, but for safety introduce a poison value that will always
trip __list_add() to assert. This allows half of the struct list_head
storage to be reclaimed with some assurance to back up the assumption
that the page count never goes to zero and a list_add() is never
attempted.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the dynamically allocated struct pages from devm_memremap_pages()
can be put to use outside the driver, we need a mechanism to track
whether they are still in use at teardown. Towards that goal reorder
the initialization sequence to allow the 'q_usage_counter' from the
request_queue to be used by the devm_memremap_pages() implementation (in
subsequent patches).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new vmem_altmap capability to enable the pmem driver to arrange
for a struct page memmap to be established in persistent memory.
[linux@roeck-us.net: mn10300: declare __pfn_to_phys() to fix build error]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In support of providing struct page for large persistent memory
capacities, use struct vmem_altmap to change the default policy for
allocating memory for the memmap array. The default vmemmap_populate()
allocates page table storage area from the page allocator. Given
persistent memory capacities relative to DRAM it may not be feasible to
store the memmap in 'System Memory'. Instead vmem_altmap represents
pre-allocated "device pages" to satisfy vmemmap_alloc_block_buf()
requests.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several scenarios where we need to retrieve and update
metadata associated with a given devm_memremap_pages() mapping, and the
only lookup key available is a pfn in the range:
1/ We want to augment vmemmap_populate() (called via arch_add_memory())
to allocate memmap storage from pre-allocated pages reserved by the
device driver. At vmemmap_alloc_block_buf() time it grabs device pages
rather than page allocator pages. This is in support of
devm_memremap_pages() mappings where the memmap is too large to fit in
main memory (i.e. large persistent memory devices).
2/ Taking a reference against the mapping when inserting device pages
into the address_space radix of a given inode. This facilitates
unmap_mapping_range() and truncate_inode_pages() operations when the
driver is tearing down the mapping.
3/ get_user_pages() operations on ZONE_DEVICE memory require taking a
reference against the mapping so that the driver teardown path can
revoke and drain usage of device pages.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams