* Don't set write-only ide_task_t.hobRegister[6] and ide_task_t.hobRegister[7]
in idedisk_set_max_address_ext().
* Add struct ide_taskfile and use it in ide_task_t instead of tfRegister[]
and hobRegister[].
* Remove no longer needed IDE_CONTROL_OFFSET_HOB define.
* Add #ifndef/#endif __KERNEL__ around definitions of {task,hob}_struct_t.
While at it:
* Use ATA_LBA define for LBA bit (0x40) as suggested by Tejun Heo.
v2:
* Add missing newlines. (Noticed by Sergei)
* Use ~ATA_LBA instead of 0xBF. (Noticed by Sergei)
* Use unnamed unions for error/feature and status/command.
(Suggested by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_xfer_verbose() fixups:
- beautify returned mode names
- fix PIO5 reporting
- make it return 'const char *'
* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().
* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
DMA info in identify block.
* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().
As a result DMA won't be tuned or will be disabled after tuning if device
reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
same checks while the IDE device is probed by ide-{cd,disk} device driver).
* Remove no longer needed ide_dma_verbose().
This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
skipping word 93 validity check
, UDMA(66)
and later debugged by Mark Lord to be caused by:
ide_dma_verbose()
printk( ... "2048kB Cache");
eighty_ninty_three()
printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
ide_dma_verbose()
printk(", UDMA(66)"
Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.
v2:
* fixes suggested by Randy:
- use KERN_CONT for printk()-s in ide-{cd,disk}.c
- don't remove argument name from ide_xfer_verbose() declaration
v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
(spotted by Sergei).
* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).
* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
limited by 'req_mode').
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check. All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.
v2:
* Fix pmac_ide_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_rate_filter() calls from host drivers to IDE core.
* Make ide_rate_filter() static.
* Make 'speed' argument of ->speedproc const.
v2:
* Fix it8213_tune_chipset() comment.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add an extra argument to ide_max_dma_mode() for passing requested transfer
mode. Use it as an upper limit when finding the best DMA for device/host.
* Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add
ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to
ide_find_dma_mode(). Also add inline ide_find_dma_mode() version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask()
to avoid false warning from eighty_ninty_three().
* Use ide_find_dma_mode() to limit the user requested transfer mode in
ide_rate_filter(). Also limit the requested mode by host max PIO mode.
Above changes make ide_rate_filter() to:
* Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19
and 0x25-0x39, values > 0x46 were already clipped down, same for values
0x25-0x39 but iff UDMA was not supported by the host).
* Clip desired transfer mode down if it is currently unsupported by IDE core
(PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was
not supported by the host).
* Clip desired transfer mode down according to the host capabilities
(UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't,
also ->atapi_dma flag was not respected).
* Clip desired transfer mode down according to the device capabilities
(except PIO modes for now which require mode work) - shouldn't be a
problem since ide_set_xfer_rate() is called _after_ device has accepted
given transfer mode.
and also result in a number of host driver specific bugfixes:
* icside
- clip unsupported PIO5 mode down
- fix unsupported/invalid modes being set in drive->current_speed
* ide-cris
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix BUG() on unsupported/invalid modes
* au1xxx-ide
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2
(if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down
* aec62xx
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
- fix 0x00 being programmed as PIO timing for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* alim15x3
- clip DMA modes down for ATAPI devices (chipset revision == 0x20 only)
- fix theoretical OOPS for 0x0F mode
- fix unsupported/invalid modes being set on the device
* amd74xx
- clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* atiixp
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix cached MWDMA mode being cleared for unsupported/invalid modes
- fix PIO{0,2} timings being programmed for unsupported/invalid modes
- fix theoretical OOPS for PIO5-6 and 0x0F modes
- fix unsupported/invalid modes being set on the device
* cmd64x
- clip unsupported SWDMA0-2 modes down
* cs5530
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* cs5535
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix theoretical OOPS for PIO5-6 and 0x0F modes
* hpt34x
- clip DMA modes down for ATAPI devices
- fix invalid timings being programmed for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* hpt366
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for unsupported/invalid modes
- fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* it8213
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* it821x
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices
(chipset in smart mode and revision 0x10 in pass-through mode)
* jmicron
- clip unsupported SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_new
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
* pdc202xx_old
- clip unsupported PIO5 mode down
- fix incorrect timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* piix
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* sc1200
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix unsupported/invalid modes being set on the device
- fix BUG() on unsupported/invalid modes
(which happened if the device accepted the setting)
* scc_pata
- clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down
* serverworks
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* siimage
- clip unsupported PIO5 and SWDMA0-2 modes down
- clip DMA modes down for ATAPI devices (SATA chipsets)
* sis5513
- clip unsupported PIO5 mode down
- fix BUG() on unsupported/invalid modes
* sl82c105
- clip unsupported SWDMA0-2 modes down
* slc90e66
- clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down
* tc86c001
- clip unsupported PIO5 and SWDMA0-2 modes down
- fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes
- fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes
- fix unsupported/invalid modes being set on the device
* triflex
- clip unsupported PIO5 mode down
* via82cxxx
- fix random PIO timings being set for unsupported/invalid modes
- fix unsupported/invalid modes being set on the device
* pmac
- clip unsupported PIO5 and SWDMA0-2 modes down
* cmd640/ht6560b
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n)
* opti621
- clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y)
- clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n)
While at it:
* Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset().
* Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->host_flags to ide_hwif_t to store ide_pci_device_t.host_flags,
assign it in setup-pci.c:ide_pci_setup_ports().
* Add IDE_HFLAG_PIO_NO_{BLACKLIST,DOWNGRADE} to ide_pci_device_t.host_flags
and teach ide_get_best_pio_mode() about them. Also remove needless
!drive->id check while at it (drive->id is always present).
* Convert amd74xx, via82cxxx and ide-timing.h to use ide_get_best_pio_mode()
and then remove no longer needed ide_find_best_pio_mode().
There should be no functionality changes caused by this patch.
Acked-by: Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
and convert all users accordingly.
* Remove no longer needed ide_pio_data_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pio_cycle_time() helper.
* Use it in ali14xx/ht6560b/qd65xx/cmd64{0,x}/sl82c105 and pmac host drivers
(previously cycle time given by the device was only used for "pio" == 255).
* Remove no longer needed ide_pio_data_t.cycle_time field.
v2:
* Fix "ata_" prefix (Noticed by Jeff).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Print info about overriding PIO mode in ide_get_best_pio_mode().
* Remove info about overriding PIO mode from cmd64{0,x} host drivers.
* Remove no longer needed ide_pio_data_t.overridden field.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...
* print user-friendly warning about limiting the maximum transfer speed
to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
also while at it cleanup eighty_ninty_three() a bit
* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
- bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
(please see FIXME comment in eighty_ninty_three() for more details)
- CONFIG_IDEDMA_IVB=y/n cases were interchanged
- check for SATA devices was missing
* remove private cable warnings from pdc_202xx{old,new} drivers now that core
code provides this functionality (plus, in pdc202xx_new case the test could
give false warnings for ATAPI devices because pdc202xx_new driver doesn't
even support ATAPI DMA)
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.
* add ide_hwif_t.udma_filter hook for filtering UDMA mask
(use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
(loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()
v2:
* rename ->filter_udma_mask to ->udma_filter
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly
Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).
v2:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dma_speed() fails to actually honor the IDE drivers' mode support
masks) because of the bogus checks -- thus, selecting the DMA transfer mode
that the driver explicitly refuses to support is possible. Additionally,
there is no check for validity of the UltraDMA mode data in the drive ID,
and the function is misdocumented.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Michal Piotrowski reported the following validator assert:
hdd: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hdd: set_drive_speed_status: error=0xb4 { AbortedCommand LastFailedSense=0x0b }
============================
[ BUG: illegal lock usage! ]
----------------------------
illegal {in-hardirq-W} -> {hardirq-on-W} usage.
hdparm/1821 [HC0[0]:SC0[0]:HE1:SE1] takes:
(ide_lock){++..}, at: [<c0268388>] ide_dump_opcode+0x13/0x9b
[...]
stack backtrace:
[<c0104513>] show_trace+0x1b/0x20
[<c01045f1>] dump_stack+0x1f/0x24
[<c013976c>] print_usage_bug+0x1a5/0x1b1
[<c0139e90>] mark_lock+0x2ca/0x4f7
[<c013aa96>] __lockdep_acquire+0x47e/0xaa4
[<c013b536>] lockdep_acquire+0x67/0x7f
[<c030552d>] _spin_lock+0x24/0x32
[<c0268388>] ide_dump_opcode+0x13/0x9b
[<c02688b6>] ide_dump_status+0x4a6/0x4cc
[<c0267ae6>] ide_config_drive_speed+0x32a/0x33a
[<c0262dc5>] piix_tune_chipset+0x2ed/0x2f8
[<c0262e31>] piix_config_drive_xfer_rate+0x61/0xb5
[<c0263a82>] set_using_dma+0x2f/0x60
[<c0263bee>] ide_write_setting+0x4a/0xc3
[<c02647ca>] generic_ide_ioctl+0x8a/0x47f
[<f886003a>] idecd_ioctl+0xfd/0x133 [ide_cd]
[<c01f1fff>] blkdev_driver_ioctl+0x4b/0x5f
[<c01f2783>] blkdev_ioctl+0x770/0x7bd
[<c017dc0d>] block_ioctl+0x1f/0x21
[<c0189353>] do_ioctl+0x27/0x6e
[<c0189604>] vfs_ioctl+0x26a/0x280
[<c0189667>] sys_ioctl+0x4d/0x7e
[<c0305ed2>] sysenter_past_esp+0x63/0xa1
in ide_dump_opcode() takes the ide_lock in an irq-unsafe manner, i.e. this
function expects to be called with irqs disabled. But
ide_dump_ata[pi]_status() doesnt do that - it enables interrupts specifically.
That is a no-no - what guarantees that another IDE port couldnt generate an
IDE interrupt while we are dumping this error? The fix is to turn the
irq-enabling in these functions into irq-disabling.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Denis Vlasenko <vda@ilport.com.ua>
* printk("\n") is misplaced, resulting in stray empty line in kernel log
* cleanups nerby: some back-to-back printks are combined, etc
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Bartlomiej Zolnierkiewicz