When trying to read any MC13892 ADC channel on a imx51-babbage board:
The MC13892 PMIC shutdowns completely.
After debugging this issue and comparing the MC13892 and MC13783
initializations done in the vendor kernel, it was noticed that the
CHRGRAWDIV bit of the ADC0 register was not being set.
This bit is set by default after power on, but the driver was
clearing it.
After setting this bit it is possible to read the ADC values correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
While polling for BOOT_DONE the chip could NAK a read because it is
still booting, which would terminate the regmap_read_poll_timeout()
with an error.
Instead implement a polling loop that ignores read errors so we
always poll until the chip signals boot or the loop times out.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't call runtime_put_sync when clk32k_ref is ARIZONA_32KZ_MCLK2
as there is no corresponding runtime_get_sync call.
MCLK1 is not in the AoD power domain so if it is used as 32kHz clock
source we need to hold a runtime PM reference to keep the device from
going into low power mode.
Fixes: cdd8da8cc6 ("mfd: arizona: Add gating of external MCLKn clocks")
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently on every resume we check for mkbp events and notify the
clients. This helps in identifying the wakeup sources. But on devices
that do not support mkbp protocol, we might end up querying key state of
the keyboard in a loop which blocks the resume. Instead check for events
only if mkbp is supported.
Signed-off-by: RaviChandra Sadineni <ravisadineni@chromium.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The main MFD driver for Samsung PMICs (S2MPSXX, S5M876X) used with
Exynos SoCs can be compiled and used as a module. The dependent clock,
regulator and RTC drivers already can be built as a module.
Building entire set of drivers as modules might require using initial
ramdisk and can make booting process longer (due to probe deferrals).
However adding such option is useful for testing and for multi-platform
configurations.
This also add required module authors to sec-irq.c file based on recent
main contributors.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The indentation should be a tab followed by two spaces.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace GPL v2.0+ license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the GPIO
descriptor API, there's a small addition to the GPIO API plus a bunch of
updates to board files to implement it. This is some really welcome
work from Linus Walleij that's had a bunch of review and has been
sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNyl0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DubB/4nWL/XSUb7qIm2fjjMUffelfk4/viB
MZg3JPEMr7ahK+QC1RQ5nOmkuACSU3Uij8RE1omLp5isfCiSa+e17f9uQx4Cn/pw
9DsIeJUEC4LvZ9gA9pDf0313B/0BIYfOMJToyLgwTNmJl+T+0e59RcS4TTCEqxwD
PmpPakOvCTD6YuVI7HhYL/HXJK1buvrAiENSjCyfyJTDaMSzJl6WMn+eibFaZbDn
NXwj2W+QyuiFCdl/7/4NWaqhlyOvM05ivnnLM/SPMBj+Iu4gSZ0PX81z98eZ3M66
YSPhF2o5SkhhffFx5xjpgR3VquXDVb0oefzhvJmZYHXi7ZKKMruoYaGB
=Ztu3
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest chunk of the regulator changes for this release outside of
the new drivers is the conversion of the fixed regulator to use the
GPIO descriptor API, there's a small addition to the GPIO API plus a
bunch of updates to board files to implement it. This is some really
welcome work from Linus Walleij that's had a bunch of review and has
been sitting in -next for a while so I'm fairly happy there's no major
issues.
- Helpers for overlapping linear ranges.
- Display opmode and consumer requested load in the regualtor_summary
file in debugfs, plus a fix there.
- Support for the fun and entertaining power off mechanism that the
pfuze100 hardware implements.
- Conversion of the fixed regulator API to use GPIO descriptors,
including pulling in a bunch of patches to a bunch of board files.
- New drivers for Cirrus Logic Lochnagar, Qualcomm PMS405, Rohm
BD71847, ST PMIC1, and TI LM363x devices"
* tag 'regulator-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: lochnagar: Use a consisent comment style for SPDX header
regulator: bd718x7: Remove struct bd718xx_pmic
regulator: Fetch enable gpiods nonexclusive
regulator/gpio: Allow nonexclusive GPIO access
regulator: lochnagar: Add support for the Cirrus Logic Lochnagar
regulator: stpmic1: Return REGULATOR_MODE_INVALID for invalid mode
regulator: stpmic1: add stpmic1 regulator driver
dt-bindings: regulator: document stpmic1 pmic regulators
regulator: axp20x: Mark expected switch fall-throughs
regulator: bd718xx: fix build warning on x86_64
regulator: fixed: Default enable high on DT regulators
regulator: bd718xx: rename bd71837 to 718xx
regulator: bd718XX use pickable ranges
regulator/mfd: bd718xx: rename bd71837/bd71847 common instances
regulator: Support regulators where voltage ranges are selectable
mfd: dt bindings: add BD71847 device-tree binding documentation
regulator: dt bindings: add BD71847 device-tree binding documentation
regulator/mfd: Support ROHM BD71847 power management IC
regulator: da905{2,5}: Remove unnecessary array check
regulator: qcom: Add PMS405 regulators
...
If a child device like touchscreen is wakeup capable, then keep ADC
interface on, so that a touching resistive screen will generate wakeup
event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently tscadc MFD is marked as wakeup capable which incorrect
because, its actually touch event by child TSC device that wakes up the
system. Therefore, remove device_init_wakeup() call that marks TSCADC
device as wakeup capable in favor of moving to mark TSC input device as
wakeup capable later.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Casting address to unsigned int causes a warning on some 64 bit
architectures. Fix the cast.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename parts of code that support both BD71837 and BD71847 to BD718XX.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BD71847 is reduced version of BD71837. DVS bucks 3 and 4 are
removed as is LDO7. Voltage ranges of some regulators are
expanded.
Add initial support for BD71847 with BD71837 driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It currently only works if the parent bus uses "simple-bus". We
currently try to probe children with non-existing compatible values.
And we're missing .probe.
I noticed this while testing devices configured to probe using ti-sysc
interconnect target module driver. For that we also may want to rebind
the driver, so let's remove __init and __exit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IRQ work is added before the struct rtc is allocated and registered,
but this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before calling menelaus_add_irq_work.
Also, this solves a possible leak as the RTC is never released.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This MFD driver is just a wrapper over atmel_serial driver and
spi-at91-usart driver. Selection of one of the drivers is based on a
property from device tree. If the property is not specified, the default
driver is atmel_serial.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cros-ec includes inside the MFD subsystem, specially the file
cros_ec_commands.h, has been modified several times and it has grown a
lot, unfortunately, we didn't have care too much about the documentation.
This patch tries to improve the documentation and also fixes all the
issues reported by kerneldoc script.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
ROHM BD71837 PMIC MFD driver providing interrupts and support
for three subsystems:
- clk
- Regulators
- input/power-key
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of Device Tree platforms, even though the Samsung PMIC sec
device is instantiated from DT, the driver is still matched through I2C
module alias. That is because I2C core always reports an I2C module
alias instead of DT one.
This could change in the future so export DT module alias.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On ams AS3722, power on when AC OK is enabled by default.
Making this option as disable by default and enable only
when platform need this explicitly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
Tested-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Pine64 H64 board uses an AXP806 PMIC in I2C and self-working mode.
The H64 SoC does not have the usual RSB controller.
This patch adds AXP806 to the list of devices supported in I2C mode.
In theory, all RSB-based PMICs can also be used in I2C mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 can operate in a standalone "self-working" mode, in which it
is also responsible for power control of the overall system. This mode
is similar to the master mode, but the EN/PWRON pin functions as a power
button, instead of a level-triggered enable switch.
This patch adds code checking for the new "x-powers,self-working-mode"
property, and a separate mfd_cell list that includes the power button
(PEK) sub-device.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For designs where CS/ADDR pin is floating, it is useful to
allow dts to define whether to keep internal pull down or not.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Configuring Speaker Mode Pullup was already supported in pdata, but not
in the dts.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CMD_GET_STATUS is not supported by some devices implementing
RDU2-compatible ICD as well as "legacy" devices. To account for that
fact, add code that obtains the same information (app/bootloader FW
version) using several different commands.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-wdt driver to properly ping the
watchdog on "legacy" firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed to make rave-sp-eeprom driver work on "legacy"
firmware.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Relying on serial port defaults for flow control and parity can result
in complete breakdown of communication with RAVE SP on some platforms
where defaults are not what we need them to be. One such case is
VF610-base ZII SPU3 board (not supported upstream). To avoid this
problem in the future, add code to explicitly configure both.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove unusded defines that are a leftover from earlier iterations of
the driver.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes https://bugs.linaro.org/show_bug.cgi?id=3903
LTP Functional tests have caused a bad paging request when triggering
the regmap_read_debugfs() logic of the device PMIC Hi6553 (reading
regmap/f8000000.pmic/registers file during read_all test):
Unable to handle kernel paging request at virtual address ffff0
[ffff00000984e000] pgd=0000000077ffe803, pud=0000000077ffd803,0
Internal error: Oops: 96000007 [#1] SMP
...
Hardware name: HiKey Development Board (DT)
...
Call trace:
regmap_mmio_read8+0x24/0x40
regmap_mmio_read+0x48/0x70
_regmap_bus_reg_read+0x38/0x48
_regmap_read+0x68/0x170
regmap_read+0x50/0x78
regmap_read_debugfs+0x1a0/0x308
regmap_map_read_file+0x48/0x58
full_proxy_read+0x68/0x98
__vfs_read+0x48/0x80
vfs_read+0x94/0x150
SyS_read+0x6c/0xd8
el0_svc_naked+0x30/0x34
Code: aa1e03e0 d503201f f9400280 8b334000 (39400000)
Investigations have showed that, when triggered by debugfs read()
handler, the mmio regmap logic was reading a bigger (16k) register area
than the one mapped by devm_ioremap_resource() during hi655x-pmic probe
time (4k).
This commit changes hi655x's max register, according to HW specs, to be
the same as the one declared in the pmic device in hi6220's dts, fixing
the issue.
Cc: <stable@vger.kernel.org> #v4.9 #v4.14 #v4.16 #v4.17
Signed-off-by: Rafael David Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona CODECs have a small timing window where they will
NAK an I2C transaction if it happens before the boot done bit is
set. This can cause the read of the register containing the boot
done bit to fail until it is set. Since regmap_read_poll_timeout
will abort polling if a read fails it can't be reliably used to
poll the boot done bit over I2C.
Do a partial revert of ef84f885e0 ("mfd: arizona: Refactor
arizona_poll_reg"), removing the regmap_read_poll_timeout but
leaving the refactoring to make the arizona_poll_reg take more
sensible arguments.
Fixes: ef84f885e0 ("mfd: arizona: Refactor arizona_poll_reg")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Ice Lake has the same LPSS than Intel Cannon Lake. Add the new IDs
to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For some errors, the wm8994_device_init function was returning or
jumping to the wrong point in the error path.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add const to the declaration of various local variables of type
kempld_platform_data for which the referenced value is always only
dereferenced or passed to a const parameter, to record the fact that
kempld_platform_data_generic is declared as const.
The semantic match that finds this issue is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,j;
@@
const struct i j = { ... };
@ok@
identifier r.i;
position p;
@@
const struct i@p *
@@
identifier r.i;
position p != ok.p;
@@
* struct i@p *
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----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=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
The EC can expose a CEC bus, thus add the cros-ec-cec MFD sub-device
when the CEC feature bit is present.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DA9063L, which is a reduced variant of the DA9063
with less regulators and without RTC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not contain RTC block, unlike the full DA9063.
Split the RTC block into separate mfd cell and register it only
on DA9063.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom IRQ map for DA9063L to
ignore the Alarm and Tick IRQs from the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DA9063L does not have an RTC. Add custom regmap for DA9063L to
prevent access into that register block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model number stored in the struct da9063 is the same for all
variants of the da9063 since it is the chip ID, which is always
the same. Replace that with a separate identifier instead, which
allows us to discern the DA9063 variants by setting the type
based on either DT match or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC_DA9063 is a complete misnomer, it denotes the value of the
DA9063 chip ID register, so rename it as such. It is also the value
of chip ID register of DA9063L though, so drop the enum as all the
DA9063 "models" share the same chip ID and thus the distinction will
have to be made using DT or otherwise.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace DA9063_NUM_IRQ macro which is not used anywhere with
plain ARRAY_SIZE().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use PLATFORM_DEVID_NONE instead of -1 in mfd_add_devices.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the regmap_irq table to use REGMAP_IRQ_REG().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the regmap_range tables to use regmap_reg_range() macro.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_mfd_add_devices() instead of plain mfd_add_devices(), which
removes the need for da9063_device_exit() altogether and also for the
.remove callback in da9063-i2c.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use devm_regmap_add_irq_chip() instead of plain regmap_add_irq_chip(),
which removes the need for da9063_irq_exit() altogether and also
fixes a bug in da9063_device_init() where the da9063_irq_exit() was
not called in a failpath.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Check whether this EC instance has USBPD host command support and
instatiate the cros_usbpd-charger driver as a subdevice in such case.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some cros-ec transport drivers (I2C, SPI) living in MFD, while
others (LPC) living in drivers/platform. The transport drivers are more
platform specific. So, move the I2C and SPI transport drivers to the
platform/chrome directory. The patch also removes the MFD_ prefix of
their Kconfig symbols.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull i2c updates from Wolfram Sang:
- mainly feature additions to drivers (stm32f7, qup, xlp9xx, mlxcpld, ...)
- conversion to use the i2c_8bit_addr_from_msg macro consistently
- move includes to platform_data
- core updates to allow the (still in review) I3C subsystem to connect
- and the regular share of smaller driver updates
* 'i2c/for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (68 commits)
i2c: qup: fix building without CONFIG_ACPI
i2c: tegra: Remove suspend-resume
i2c: imx-lpi2c: Switch to SPDX identifier
i2c: mxs: Switch to SPDX identifier
i2c: busses: make use of i2c_8bit_addr_from_msg
i2c: algos: make use of i2c_8bit_addr_from_msg
i2c: rcar: document R8A77980 bindings
i2c: qup: Add command-line parameter to override SCL frequency
i2c: qup: Correct duty cycle for FM and FM+
i2c: qup: Add support for Fast Mode Plus
i2c: qup: add probe path for Centriq ACPI devices
i2c: robotfuzz-osif: drop pointless test
i2c: robotfuzz-osif: remove pointless local variable
i2c: rk3x: Don't print visible virtual mapping MMIO address
i2c: opal: don't check number of messages in the driver
i2c: ibm_iic: don't check number of messages in the driver
i2c: imx: Switch to SPDX identifier
i2c: mux: pca954x: merge calls to of_match_device and of_device_get_match_data
i2c: mux: demux-pinctrl: use proper parent device for demux adapter
i2c: mux: improve error message for failed symlink
...
This function is no longer called, so we get a harmless
warning until it is removed as well:
drivers/mfd/cros_ec_dev.c:265:13: error: '__remove' defined but not used [-Werror=unused-function]
Fixes: 3aa2177e47 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is not mandatory that platform data is passed along the ac97
codec. Actually there are configuration without a battery connected to
the ADC of the codec.
This is for example the case for the PXA zylonite platform, so fix the
NULL dereferencing by adding a test.
Fixes: a5c6951c49 ("mfd: wm97xx-core: core support for wm97xx Codec")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned out
to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from Maciej
Purski, unfortunately there are further problems there so the last
couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW regulators
on Qualcomm SPMI and dropped support for some preproduction chips
that never made it to market from the AB8500 driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlsarcETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B4HB/9MFV/MK7Hw2hsVCX3qWTiH4tJ/X0MG
tGz1PfmbH0CJ9ly5g+rvCoT+1/s7BydKzi1cd1RHnimBv2U1XagwSny3LNEcJs2Q
pmhpGViakkQI/Y2h+u/j0Jk1nE+jTiKk+1ozUB7YnPekrGyQlf7TMhvKOLTvLKyX
56jdNxcW0MgSnXV2N6y4NpWhgvrQwvKjacTxV5iX7WP2rnK2WNFeG7Q859buhtI0
znRi+tO5hZsw5T44ickdPfotZn+i5o7MYLCkkaA2h1EwtpbYwVINfUjp3KtuyFhH
3B9GmCsjjN2Z2eInnkpzWfVXK2S1Vlp6+ka2FSs+U/4rVdd3Bw2KkblS
=Ftua
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned
out to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from
Maciej Purski, unfortunately there are further problems there so the
last couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW
regulators on Qualcomm SPMI and dropped support for some preproduction
chips that never made it to market from the AB8500 driver"
* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
regulator: gpio: Revert
ARM: pxa, regulator: fix building ezx e680
regulator: Revert coupled regulator support again
regulator: wm8994: Fix shared GPIOs
regulator: max77686: Fix shared GPIOs
regulator: bd71837: BD71837 PMIC regulator driver
regulator: bd71837: Devicetree bindings for BD71837 regulators
regulator: gpio: Get enable GPIO using GPIO descriptor
regulator: fixed: Convert to use GPIO descriptor only
regulator: s2mps11: Fix boot on Odroid XU3
dt-bindings: qcom_spmi: Document SAW support
regulator: qcom_spmi: Add support for SAW
regulator: tps65090: Pass descriptor instead of GPIO number
regulator: s5m8767: Pass descriptor instead of GPIO number
regulator: pfuze100: Delete reference to ena_gpio
regulator: max8952: Pass descriptor instead of GPIO number
regulator: lp8788-ldo: Pass descriptor instead of GPIO number
regulator: lm363x: Pass descriptor instead of GPIO number
regulator: max8973: Pass descriptor instead of GPIO number
regulator: mc13xxx-core: Switch to SPDX identifier
...
cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with.
Kudos to Laura Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare
dwapb driver.
Misc:
- Random cleanups, right header files in the drivers, some
size optimizations etc.
-----BEGIN PGP SIGNATURE-----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=Ly/0
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.18 development cycle.
Core changes:
- We have killed off VLA from the core library and all drivers.
The background should be clear for everyone at this point:
https://lwn.net/Articles/749064/
Also I just don't like VLA's, kernel developers hate it when
compilers do things behind their back. It's as simple as that.
I'm sorry that they even slipped in to begin with. Kudos to Laura
Abbott for exorcising them.
- Support GPIO hogs in machines/board files.
New drivers and chip support:
- R-Car r8a77470 (RZ/G1C)
- R-Car r8a77965 (M3-N)
- R-Car r8a77990 (E3)
- PCA953x driver improvements to accomodate more variants.
Improvements and new features:
- Support one interrupt per line on port A in the DesignWare dwapb
driver.
Misc:
- Random cleanups, right header files in the drivers, some size
optimizations etc"
* tag 'gpio-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpio: davinci: fix build warning when !CONFIG_OF
gpio: dwapb: Fix rework support for 1 interrupt per port A GPIO
gpio: pxa: Include the right header
gpio: pl061: Include the right header
gpio: pch: Include the right header
gpio: pcf857x: Include the right header
gpio: pca953x: Include the right header
gpio: palmas: Include the right header
gpio: omap: Include the right header
gpio: octeon: Include the right header
gpio: mxs: Switch to SPDX identifier
gpio: Remove VLA from stmpe driver
gpio: mxc: Switch to SPDX identifier
gpio: mxc: add clock operation
gpio: Remove VLA from gpiolib
gpio: aspeed: Use a cache of output data registers
gpio: aspeed: Set output latch before changing direction
gpio: pca953x: fix address calculation for pcal6524
gpio: pca953x: define masks for addressing common and extended registers
gpio: pca953x: set the PCA_PCAL flag also when matching by DT
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAlsYJ1gWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJlCTEACwdEeriAd2VwxknnsstojGD/3g
8TTFA19vSu4Gxa6WiDkjGoSmIlfhXTlZo1Nlmencv16ytSvIVDNLUIB3uDxUIv1J
2+dyHML9JpXYHHR7zLXXnGFJL0wazqjbsD3NYQgXqmun7EVVYnOsAlBZ7h/Lwiej
jzEJd8DaHT3TA586uD3uggiFvQU0yVyvkDCDONIytmQx+BdtGdg9TYCzkBJaXuDZ
YIthyKDvxIw5nh/UaG3L+SKo73tUr371uAWgAfqoaGQQCWe+mxnWL4HkCKsjFzZL
u9ouxxF/n6pij3E8n6rb0i2fCzlsTDdDF+aqV1rQ4I4hVXCFPpHUZgjDPvBWbj7A
m6AfRHVNnOgI8HGKqBGOfViV+2kCHlYeQh3pPW33dWzy/4d/uq9NIHKxE63LH+S4
bY3oO2ela8oxRyvEgXLjqmRYGW1LB/ZU7FS6Rkx2gRzo4k8Rv+8K/KzUHfFVRX61
jEbiPLzko0xL9D53kcEn0c+BhofK5jgeSWxItdmfuKjLTW4jWhLRlU+bcUXb6kSS
S3G6aF+L+foSUwoq63AS8QxCuabuhreJSB+BmcGUyjthCbK/0WjXYC6W/IJiRfBa
3ZTxBC/2vP3uq/AGRNh5YZoxHL8mSxDfn62F+2cqlJTTKR/O+KyDb1cusyvk3H04
KCDVLYPxwQQqK1Mqig==
=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
Pull input updates from Dmitry Torokhov:
- a new driver to ChipOne icn8505 based touchscreens
- on certain systems with Elan touch controllers they will be switched
away form PS/2 emulation and over to native SMbus mode
- assorted driver fixups and improvements
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: elan_i2c - add ELAN0612 (Lenovo v330 14IKB) ACPI ID
Input: goodix - add new ACPI id for GPD Win 2 touch screen
Input: xpad - add GPD Win 2 Controller USB IDs
Input: ti_am335x_tsc - prevent system suspend when TSC is in use
Input: ti_am335x_tsc - ack pending IRQs at probe and before suspend
Input: cros_ec_keyb - mark cros_ec_keyb driver as wake enabled device.
Input: mk712 - update documentation web link
Input: atmel_mxt_ts - fix reset-gpio for level based irqs
Input: atmel_mxt_ts - require device properties present when probing
Input: psmouse-smbus - allow to control psmouse_deactivate
Input: elantech - detect new ICs and setup Host Notify for them
Input: elantech - add support for SMBus devices
Input: elantech - query the resolution in query_info
Input: elantech - split device info into a separate structure
Input: elan_i2c - add trackstick report
Input: usbtouchscreen - add sysfs attribute for 3M MTouch firmware rev
Input: ati_remote2 - fix typo 'can by' to 'can be'
Input: replace hard coded string with __func__ in pr_err()
Input: add support for ChipOne icn8505 based touchscreens
Input: gamecon - avoid using __set_bit() for capabilities
...
Regmap configuration tables for Cirrus Logic CS47L90 and CS47L91 codecs.
Signed-off-by: Nikesh Oswal <nikesh@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap configuration tables for Cirrus Logic CS47L85 codecs.
Signed-off-by: Nariman Poushin <nariman@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regmap configuration tables for Cirrus Logic CS47L35 codecs.
Signed-off-by: Piotr Stankiewicz <piotrs@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds the generic core support for Cirrus Logic "Madera" class codecs.
These are complex audio codec SoCs with a variety of digital and analogue
I/O, onboard audio processing and DSPs, and other features.
These codecs are all based off a common set of hardware IP so can be
supported by a core of common code (with a few minor device-to-device
variations).
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- asus_atk0110 driver modified to use new API
- k10temp supports new CPUs and reports both Tctl and Tdie
- minor fixes in gpio-fan, ltc2990, fschmd, and mc13783 drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3w3p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- asus_atk0110 driver modified to use new API
- k10temp supports new CPUs and reports both Tctl and Tdie
- minor fixes in gpio-fan, ltc2990, fschmd, and mc13783 drivers
* tag 'hwmon-for-linus-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (asus_atk0110) Make use of device managed memory
hwmon: (asus_atk0110) Replace deprecated device register call
hwmon: (k10temp) Make function get_raw_temp static
hwmon: (gpio-fan) Fix "#cooling-cells" property name in bindings
MAINTAINERS: hwmon: Add Documentation/devicetree/bindings/hwmon
hwmon: (ltc2990) support all measurement modes
hwmon: (ltc2990) add devicetree binding
hwmon: (ltc2990) Fix incorrect conversion of negative temperatures
hwmon: (core) check parent dev != NULL when chip != NULL
hwmon: (fschmd) fix typo 'can by' to 'can be'
hwmon: (k10temp) Display both Tctl and Tdie
hwmon: (k10temp) Add support for Stoney Ridge and Bristol Ridge CPUs
hwmon: MC13783: Add uid and die temperature sensor inputs
If the feature query fails during this driver's probe, we memset the
features bits to 0, but then we continue to overwrite that with whatever
junk we read back when the feature probing failed. In the case of a SPI
device, it may be complete junk, causing the caller of this function to
think certain features are present when they aren't. Don't copy over the
bad message on failure so we can fail more gracefully.
Fixes: e4244ebdda ("platform/chrome: Introduce a new function to check EC features.")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C.
This incorrect input clock rate results too high I2C bus clock in case
ACPI doesn't provide tuned I2C timing parameters since I2C host
controller driver calculates them from input clock rate.
Fix this by using the correct rate. We still share the same 230 ns SDA
hold time value than Sunrisepoint.
Cc: stable@vger.kernel.org
Fixes: b418bbff36 ("mfd: intel-lpss: Add Intel Cannonlake PCI IDs")
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reported-by: Chris Chiu <chiu@endlessm.com>
Reported-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MMC framework requires the ocr_mask to be provided. Without it, the
SD card is not detected, especially on the hx4700 platform.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial fix to spelling mistake in dev_err message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to documentation the function has 2 bits for reset
while iDMA 64-bit has only one.
Rename it accordingly. Note, there is no functional change since
we always handle them together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the compatibles and PMIC ids for the pm8005, pm8998, and pmi8998
PMICS found on MSM8998 and SDM845 based platforms.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Mark cros_ec_keyb has wake enabled by default. If we see a MKBP event
related to keyboard, call pm_wakeup_event() to make sure wakeup
triggers are accounted to keyb during suspend resume path.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 3c6b38d45f "regulator: wm8994: Pass
descriptor instead of GPIO number" as it has problems with shared
GPIOs similar to that on s2mps11.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to documentation REMAP register has to be programmed in
either DMA or PIO mode of the slice.
Move the DMA capability check below to let REMAP register be programmed
in PIO mode.
Cc: stable@vger.kernel.org # 4.3+
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec_i2c driver is still active after it had suspended or before it
resumes. Besides that, it also tried to transfer data even after the I2C
host had been suspended. This will lead the system to crash.
During the test, we also observe that the EC needs to be resumed earlier
due to some status polling from the EC FW (e.g. battery status). So we
move the PM ops to late stage to make it work normally.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reboot or shutdown during delayed works could corrupt communication with
EC and certain I2C controller may not be able to recover from the error
state.
This patch registers a shutdown callback used to cancel the debugfs log
worker thread.
Signed-off-by: Daniel Hung-yu Wu <hywu@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Check whether this EC instance has RTC host command support and instatiate
the RTC driver as a subdevice in such case.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should stop our worker thread while we're suspended. If we don't
then we'll get messages like:
cros-ec-spi spi5.0: spi transfer failed: -108
cros-ec-spi spi5.0: cs-deassert spi transfer failed: -108
cros-ec-ctl cros-ec-ctl.0.auto: EC communication failed
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Free the IRQ we might have requested when removing the cros_ec device,
so we can unload and reload the driver properly.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The string.h header file is needed for the memset() definition. The RT
build fails because it is not pulled in via other header files.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 001dde9400 ("mfd: cros ec: spi: Fix "in progress" error
signaling") pointed out some bad code, but its analysis and conclusion
was not 100% correct.
It *is* correct that we should not propagate result==EC_RES_IN_PROGRESS
for transport errors, because this has a special meaning -- that we
should follow up with EC_CMD_GET_COMMS_STATUS until the EC is no longer
busy. This is definitely the wrong thing for many commands, because
among other problems, EC_CMD_GET_COMMS_STATUS doesn't actually retrieve
any RX data from the EC, so commands that expected some data back will
instead start processing junk.
For such commands, the right answer is to either propagate the error
(and return that error to the caller) or resend the original command
(*not* EC_CMD_GET_COMMS_STATUS).
Unfortunately, commit 001dde9400 forgets a crucial point: that for
some long-running operations, the EC physically cannot respond to
commands any more. For example, with EC_CMD_FLASH_ERASE, the EC may be
re-flashing its own code regions, so it can't respond to SPI interrupts.
Instead, the EC prepares us ahead of time for being busy for a "long"
time, and fills its hardware buffer with EC_SPI_PAST_END. Thus, we
expect to see several "transport" errors (or, messages filled with
EC_SPI_PAST_END). So we should really translate that to a retryable
error (-EAGAIN) and continue sending EC_CMD_GET_COMMS_STATUS until we
get a ready status.
IOW, it is actually important to treat some of these "junk" values as
retryable errors.
Together with commit 001dde9400, this resolves bugs like the
following:
1. EC_CMD_FLASH_ERASE now works again (with commit 001dde9400, we
would abort the first time we saw EC_SPI_PAST_END)
2. Before commit 001dde9400, transport errors (e.g.,
EC_SPI_RX_BAD_DATA) seen in other commands (e.g.,
EC_CMD_RTC_GET_VALUE) used to yield junk data in the RX buffer; they
will now yield -EAGAIN return values, and tools like 'hwclock' will
simply fail instead of retrieving and re-programming undefined time
values
Fixes: 001dde9400 ("mfd: cros ec: spi: Fix "in progress" error signaling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
This header only contains platform_data. Move it to the proper directory.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DesignWare GPIO IP can be configured for either 1 interrupt or 1
per GPIO in port A, but the driver currently only supports 1 interrupt.
See the DesignWare DW_apb_gpio Databook description of the
'GPIO_INTR_IO' parameter.
This change allows the driver to work with up to 32 interrupts, it will
get as many interrupts as specified in the DT 'interrupts' property.
It doesn't do anything clever with the different interrupts, it just calls
the same handler used for single interrupt hardware.
ACPI companion code provided by Hoan Tran <hotran@apm.com>. This was tested
on X-Gene by Hoan.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The COMP1 and COMP2 elements are in 0 and 1 respectively so this code is
accessing the wrong elements and one space beyond the end of the array.
The "id" variable is never COMP (0) so that code can be removed.
Fixes: 6851ad3ab3 ("TPS65911: Comparator: Add comparator driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As part of the effort to remove VLAs from the kernel[1], this creates
constants for the checksum lengths of CCITT and 8B2C and changes
crc_calculated to be the maximum size of a checksum.
https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Kyle Spiers <ksspiers@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In 2012, we changed the tps65910 API and fixed most drivers but forgot
to update this one.
Fixes: 3f7e82759c ("mfd: Commonize tps65910 regmap access through header")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When looking up the clock we must use the client->dev as device since that
is the one which is probed via DT.
Cc: stable@vger.kernel.org # 4.16+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When AXP806 support was added, POK was incorrectly expanded to PWROK.
However, the datasheet lists them as POK[LSNP], which is the same as
on the AXP288. Furthermore, the registers associated with POK functions
are the same as the PEK on the other AXP PMICs. This suggests that
"POK" means "Power On Key", much like "PEK" means "Power Enable Key",
instead of "Power OK".
This patch changes the "PWROK" prefix to "POK" for these interrupts.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Previously we were open coding the interrupts for the various mfd
cells. This made the code somewhat long due to pretty-formatting.
This patch convert those into one-line declarations with DEFINE_RES_IRQ,
making the code shorter and easier to read.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x driver has lots of mfd_cell and resource structs.
These can all be const-ified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace multi-line entries in the regmap_range arrays with single
line macros: regmap_reg_range(). This will leave the static structure
array entries for regmap_range unaltered. It will significantly reduce
the line count in the DA9062/61 core file.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now GPIOD has support for both pdata systems and for non-standard DT
bindings the Arizona reset GPIO can be converted to use it. Worth
noting gpiod_set_raw_value_cansleep is used to match the behaviour
of the old GPIOs. This is because the part is fairly widely used and
it is unknown how many DTs are correctly setting active low through
device tree, so to avoid breaking any existing users it is best to
match the previous behaviour.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are some global registers in Spreadtrum sc27xx PMICs, which will
be accessed by other drivers. So this patch adds one syscon cell to
help to access the PMIC's global registers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If a 'platform_device_alloc()' call fails, we still need to release the
resources that have already been allocated before returning.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the assignment for the local variable "dev" so that its setting
will be performed after a configuration check by this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The local variable "dev" will be reassigned by a following statement.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace the specification of data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace the specification of two data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Check received frame length _before_ accepting next byte in order to
avoid incorrectly rejecting payloads that are RAVE_SP_RX_BUFFER_SIZE
long.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert print_hex_dump() to print_hex_dump_debug() to be able to
leverage CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add code that would query and print out bootloader and application
firmware version info.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use kasprintf instead of combination of kmalloc and sprintf.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As axp20x-battery-power-supply now supports AXP813, add a cell for it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes the axp20x_adc driver probe with platform device id
"axp813-adc".
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This makes AXP209 and AXP22x ADCs probe first via DT and then by
fallback via platform.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit e04653a9dc.
It is no longer needed to install Chrome EC GPE handler to have
GPE enabled in suspend to idle path. It is found that with this
handler installed, EC wake up doesn't work because default EC
event handler that can wake up system is not getting called.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the GPL v2 license boilerplate and update with
the SPDX license identifier.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This sets the regmap name to the device tree node name. This is useful
for debugging.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allocating memory to store clk array together with driver
data simplifies error unwinding and allows deleting memory
allocation failure message as there is now only single point
of failure already covered by allocation failure report.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Markus Elfring: simplified error unwinding, error message removal]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=r+0D
-----END PGP SIGNATURE-----
mergetag object 55d1d1547a
type commit
tag ib-mfd-input-rtc-v4.18
tagger Lee Jones <lee.jones@linaro.org> 1523888198 +0100
Immutable branch between MFD, Input and RTC due for the v4.18 merge window
-----BEGIN PGP SIGNATURE-----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=O7G8
-----END PGP SIGNATURE-----
mergetag object ab3a897847
type commit
tag ib-mfd-pwm-v4.18
tagger Lee Jones <lee.jones@linaro.org> 1526458673 +0100
Immutable branch between MFD and PWM due for the v4.18 merge window
-----BEGIN PGP SIGNATURE-----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=SU5E
-----END PGP SIGNATURE-----
Merge tags 'ib-mfd-hwmon-v4.18', 'ib-mfd-input-rtc-v4.18' and 'ib-mfd-pwm-v4.18' into ibs-for-mfd-merged
Immutable branch between MFD and HWMON due for the v4.18 merge window
Immutable branch between MFD, Input and RTC due for the v4.18 merge window
Immutable branch between MFD and PWM due for the v4.18 merge window
STM32 Timers can support up to 7 DMA requests:
- 4 channels, update, compare and trigger.
Optionally request part, or all DMAs from stm32-timers MFD core.
Also add routine to implement burst reads using DMA from timer registers.
This is exported. So, it can be used by child drivers, PWM capture
for instance (but not limited to).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enable read/write access to the BD9571MWV_BKUP_MODE_CNT register, which
is amongst others used to configure DDR Backup Power.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds compatible strings and interrupts for pmic keys
which serves as child device of MFD.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The core driver should create and manage irq mappings instead of
leaf drivers. This patch change to pass irq domain to
devm_mfd_add_devices() and it will create mapping for irq resources
automatically. And remove irq mapping in rtc driver since this has
been done in core driver.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a sysfs attribute (/sys/class/chromeos/cros_ec/kb_wake_angle)
used to set and get the keyboard wake lid angle. This attribute is
present only if 2 accelerometers are controlled by the EC.
This patch also moves the cros_ec features check before the device is
added so the features map obtained from the EC is ready on time.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DEFINE_SHOW_ATTRIBUTE() helper macro would be useful for current
users, which are many of them, and for new comers to decrease code
duplication.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
A very busy release for regmap, all fairly specialist stuff but useful:
- Support for disabling locking from Bartosz Golaszewski, allowing
users that handle their own locking to save some overhead.
- Support for hwspinlocks in syscons in MFD from Baolin Wang, this is
going through the regmap tree since the first users turned up some
some cases that needed interface tweaks with 0 being used as a syscon
identifier.
- Support for devices with no read or write flag from Andrew F. Davis.
- Basic support for devices on SoundWire buses from Vinod Koul.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlpvTfYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Cd8B/4zeYHL73moxvAxAH/99HGVCHQHcR4k
hdLaGHs8JN5ZLoNCqixFdkffsdBM2H06JPOnBZMHHcb5Pf7KL3OEgPNeiMUpzxUL
0EcXoZiJz0HzRVwi6M9nt3Bv41rD5+v9nS6oolsqbU1b6w5ofZQ7ENeN+nhxLk54
Wy8avQ3VDmiKsSAAXDMEA6i58Zz7dT1ibyyOcYGyEdt7iFOL8d0aM4c3cAGHfL+E
Ss9/dyeY/8glLDy+rxp5hZHkLY7FKFDQcD1/FSR26DHslc0Swa9mn/0SmhF0pQWe
RVEn63b4B5iT0E8brlWHwNh466jT6+fyJKzYDzEM+v1RP4qUmluFubjK
=X/P5
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A very busy release for regmap, all fairly specialist stuff but
useful:
- Support for disabling locking from Bartosz Golaszewski, allowing
users that handle their own locking to save some overhead.
- Support for hwspinlocks in syscons in MFD from Baolin Wang, this is
going through the regmap tree since the first users turned up some
some cases that needed interface tweaks with 0 being used as a
syscon identifier.
- Support for devices with no read or write flag from Andrew F.
Davis.
- Basic support for devices on SoundWire buses from Vinod Koul"
* tag 'regmap-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
mfd: syscon: Add hardware spinlock support
regmap: Allow empty read/write_flag_mask
regcache: flat: Un-inline index lookup from cache access
regmap: Add SoundWire bus support
regmap: Add one flag to indicate if a hwlock should be used
regmap: debugfs: document why we don't create the debugfs entries
regmap: debugfs: emit a debug message when locking is disabled
regmap: use proper part of work_buf for storing val
regmap: potentially duplicate the name string stored in regmap
regmap: Disable debugfs when locking is disabled
regmap: rename regmap_lock_unlock_empty() to regmap_lock_unlock_none()
regmap: allow to disable all locking mechanisms
regmap: Remove the redundant config to select hwspinlock
* pm-core: (29 commits)
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
PM: i2c-designware-platdrv: Optimize power management
PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
PM / core: Assign the wakeup_path status flag in __device_prepare()
PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
PM / core: Add helpers for subsystem callback selection
PM / wakeup: Drop redundant check from device_init_wakeup()
PM / wakeup: Drop redundant check from device_set_wakeup_enable()
PM / wakeup: only recommend "call"ing device_init_wakeup() once
...
Some system control registers need hardware spinlock to synchronize
between the multiple subsystems, so we should add hardware spinlock
support for syscon.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the intel-lpss driver set DPM_FLAG_SMART_SUSPEND for its
devices which will allow them to stay in runtime suspend during
system suspend unless they need to be reconfigured for some reason.
Also make it avoid resuming its child devices if they have
DPM_FLAG_SMART_SUSPEND set to allow them to remain in runtime
suspend during system suspend.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Just to be on the safe side, don't touch the bit. If write access to the
flash chip is needed, the BIOS needs to enable it explicitly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The input current limit bits get updated by the charger detection logic,
so we should not cache the contents of this register.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This macro deduplicates a lot of similar code in the ab8500-debugfs.c module.
Targeting to be moved to seq_file.h eventually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The controller used by a flexcom module is configured at boot, and left
alone after this. In the suspend mode called "backup with self-refresh"
available on SAMA5D2, the chip will resume with most of its registers
reset. In this case, we need to restore the state of the flexcom driver
on resume.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add SPDX identifier
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As GPIO/pinctrl driver now supports AXP813, add a cell for it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This should be enabled so that we get full compile coverage
of the PM8xxx MFD core with the different subdrivers.
Tested on the build servers.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These registers are only used in drivers/mfd/tmio_core.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The EC SPI driver prevents SPI transfers being to rapidly by keeping
track of the time the last transfer was issued via the
'last_transfer_ns' variable. Previously, if the 'last_transfer_ns'
variable was zero, this indicated that no previous transfer had been
sent and that no delay was needed. However, the EC SPI driver has
been updated to always initialise the 'last_transfer_ns' variable
during probe and therefore, it is no longer necessary to test if it
is zero. Remove the code that checks if this variable is zero.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The powerhold mask for TPS65917 is different when comapred to
the other palmas versions. Hence assign the right mask that enables
power off of tps65917 pmic correctly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add jump targets so that two error messages are stored only once
at the end of this function implementation.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Node is being initialized a value that is never read, it is
being written over a few statements into the function with
the return value from call to of_get_child_by_name. Hence
this initialization can be removed. Cleans up clang warning:
drivers/mfd/ti_am335x_tscadc.c:127:22: warning: Value stored
to 'node' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial fix to spelling mistakes in 'pcf50633_client_dev_register'.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver for RAVE Supervisory Processor, an MCU implementing
various bits of housekeeping functionality (watchdoging, backlight
control, LED control, etc) on RAVE family of products by Zodiac
Inflight Innovations.
This driver implementes core MFD/serdev device as well as
communication subroutines necessary for commanding the device.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'Commit cc27b735ad ("PCI/portdrv: Turn off PCIe services during
shutdown")' revealed a resource leak in rtsx_pci driver during shutdown.
Issue shows up as a warning during shutdown as follows:
remove_proc_entry: removing non-empty directory 'irq/17', leaking at least
'rtsx_pci'
WARNING: CPU: 0 PID: 1578 at fs/proc/generic.c:572
remove_proc_entry+0x11d/0x130
Modules linked in <long list but none that are out-of-tree>
...
Call Trace:
unregister_irq_proc
free_desc
irq_free_descs
mp_unmap_irq
acpi_unregister_gsi_apic
acpi_pci_irq_disable
do_pci_disable_device
pci_disable_device
device_shutdown
kernel_restart
Sys_reboot
Even though rtsx_pci driver implements a shutdown callback, it is not
releasing the interrupt that it registered during probe. This is causing
the ACPI layer to complain that the shared IRQ is in use while freeing
IRQ.
This code releases the IRQ to prevent resource leak and eliminate the
warning.
Fixes: cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198141
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec_dev module is responsible for registering the MFD devices
attached to the ChromeOS EC. This patch moves this module to drivers/mfd
so calls to mfd_add_devices() are not done from outside the MFD subtree
anymore.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch splits the cros_ec_devs module in two parts with a
cros_ec_dev module responsible for handling MFD devices registration and
a cros_ec_ctl module responsible for handling the various user-space
interfaces.
For consistency purpose, the driver name for the cros_ec_dev module is
now cros-ec-dev instead of cros-ec-ctl.
In the next commit, the new cros_ec_dev module will be moved to the MFD
subtree so mfd_add_devices() calls are not done from outside MFD.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For host commands that take a long time to process, cros ec can return
early by signaling a EC_RES_IN_PROGRESS result. The host must then poll
status with EC_CMD_GET_COMMS_STATUS until completion of the command.
None of the above applies when data link errors are encountered. When
errors such as EC_SPI_PAST_END are encountered during command
transmission, it usually means the command was not received by the EC.
Treating such errors as if they were 'EC_RES_IN_PROGRESS' results is
almost always the wrong decision, and can result in host commands
silently being lost.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Note that the CONFIG_OF compile guard can be removed as
of_get_child_by_name() provides a !CONFIG_OF implementation which always
fails.
Cc: stable <stable@vger.kernel.org> # 3.5
Fixes: 37e13cecaa ("mfd: Add support for Device Tree to twl6040")
Fixes: ca2cad6ae3 ("mfd: Fix twl6040 build failure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while leaking any matching node.
To make things worse, any matching node would not even necessarily be a
child node as the whole device tree was searched depth-first starting at
the parent.
Fixes: 019a7e6b7b ("mfd: twl4030-audio: Add DT support")
Cc: stable <stable@vger.kernel.org> # 3.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the Tegra124 Nyan-Big chromebook the very first SPI message sent to
the EC is failing.
The Tegra SPI driver configures the SPI chip-selects to be active-high
by default (and always has for many years). The EC SPI requires an
active-low chip-select and so the Tegra chip-select is reconfigured to
be active-low when the EC SPI driver calls spi_setup(). The problem is
that if the first SPI message to the EC is sent too soon after
reconfiguring the SPI chip-select, it fails.
The EC SPI driver prevents back-to-back SPI messages being sent too
soon by keeping track of the time the last transfer was sent via the
variable 'last_transfer_ns'. To prevent the very first transfer being
sent too soon, initialise the 'last_transfer_ns' variable after calling
spi_setup() and before sending the first SPI message.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fabio Estevam