bna & bfa firmware version 3.2.5.1 was submitted to linux-firmware on
Feb 17 19:10:20 2015 -0500 in 0ab54ff1dc ("linux-firmware: Add QLogic BR
Series Adapter Firmware").
bna was updated to use the newer firmware on Feb 19 16:02:32 2015 -0500 in
3f307c3d70 ("bna: Update the Driver and Firmware Version")
bfa was not updated. I presume this was an oversight but it broke support
for bfa+bna cards such as the following
04:00.0 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.1 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.2 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.3 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
Currently, if the bfa module is loaded first, bna fails to probe the
respective devices with
[ 215.026787] bna: QLogic BR-series 10G Ethernet driver - version: 3.2.25.1
[ 215.043707] bna 0000:04:00.2: bar0 mapped to ffffc90001fc0000, len 262144
[ 215.060656] bna 0000:04:00.2: initialization failed err=1
[ 215.073893] bna 0000:04:00.3: bar0 mapped to ffffc90002040000, len 262144
[ 215.090644] bna 0000:04:00.3: initialization failed err=1
Whereas if bna is loaded first, bfa fails with
[ 249.592109] QLogic BR-series BFA FC/FCOE SCSI driver - version: 3.2.25.0
[ 249.610738] bfa 0000:04:00.0: Running firmware version is incompatible with the driver version
[ 249.833513] bfa 0000:04:00.0: bfa init failed
[ 249.833919] scsi host6: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.0 driver: 3.2.25.0
[ 249.841446] bfa 0000:04:00.1: Running firmware version is incompatible with the driver version
[ 250.045449] bfa 0000:04:00.1: bfa init failed
[ 250.045962] scsi host7: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.1 driver: 3.2.25.0
Increase bfa's requested firmware version. Also increase the driver
version. I only tested that all of the devices probe without error.
Reported-by: Tim Ehlers <tehlers@gwdg.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Patch includes changes to upgrade bfa driver version to 3.2.23.0 and use
firmware version 3.2.3.0
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch addresses the issue of port not being registered with SCSI
layer on bfa or firmware initialization failure and subsequently failure
in collecting driver traces for debugging port init failures. Also it
has minor changes related to bfad state machine clean up.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update bfa driver version to 3.2.21.1
Update bfa to use firmware image versions 3.2.1.0
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added few missing endian swap changes to support BFA on PowerPC.
- Added PCIE AER support to BFA:
a) Implemented the PCI error handler entry points.
b) Made changes to FCS state machine to handle STOP event from the
PCI error detected entry point.
c) Made changes to the IO Controller state machine to handle SUSPEND
event from the PCI error detected entry point.
d) Made changes to restart the BFA operations on a slot_reset completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch re-implements LUN Masking feature using SCSI Slave Callouts. With
the new design in the slave_alloc entry point; for each new LUN discovered we
check with our internal LUN Masking config whether to expose or to mask this
particular LUN. We return -ENXIO (No such device or address) from slave_alloc
for the LUNs we don't want to be exposed. We also notify the SCSI mid-layer
to do a sequential LUN scan rather than REPORT_LUNS based scan if LUN masking
is enabled on our HBA port, since a -ENXIO from any LUN in REPORT_LUNS based
scan translates to a scan abort. This patch also handles the dynamic lun
masking config change from enable to disable or vice-versa by resetting
sdev_bflags of LUN 0 appropriately.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Added support to post vendor unique events on fc_host.
- Supports adapter, port, ioc, flash and remote port based AEN events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added a new module parameter max_xfer_size to
set the max_sectors in the scsi_host template.
- Added logic to handle request_irq() failure so
that msix vector resource is de-allocated immediately
when failure happens.
- BSG enhancements to collect vHBA releated info and port log.
- Removed the workaround of incrementing the module refcnt on bsg request.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to collect driver/fw stats.
- Added support to perform adapter/ioc enable, disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added logic to initiate a PLOGI to the target, while processing a LOGO
from the same target in Direct attach mode.
- Added logic to generate a FCCT Reject indicating unsupported command,
upon receiving FCCT/FCGS requests.
- Added logic to set the fcpim in offline state and avoid any PRLI retries
if a PRLI response is a reject with a reason Command Not Supported.
- Updated the FDMI Supported/Current speeds.
- Added logic to wait for the response from the firmware before sending
ACC to PLOGI and transitioning to subsequent states - while processing an
Incoming PLOGI in online state.
- Added a wait state in the fcs_vport state machine - For case where
FDISC is in progress and we get a vport delete request we wait for
fdisc response and will transition to the appropriate state based on
rsp status, else its causing both driver/fw resources to be not
freed.
- Remove the fc_credit_recovery module param.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Modified the design such that each BFA sub-module will provide
the amount of DMA and KVA memory needed by it and queues the
same request to the global dma and kva info queues.
- During the memory allocation we iterate over this queue to allocate
the dma and kva memory requested by sub-modules.
- The change is needed to avoid requesting the aggregate amount of memory
needed by all the BFA sub-modules as one contiguous chunk.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added BSG interface support to BFA driver
- Adds support to send ELS/CT FC passthru commands and
few vendor specific BSG requests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove OS wrapper functions/macros, and as a result remove bfa_os_inc.h.
Signed-off-by: Maggie Zhang <xmzhang@brocade.com>
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch addresses the comments from Randy Dunlap (Randy.Dunlap@oracle.com)
regarding comment blocks that begining with "/**". bfa driver comments
currently do not follow kernel-doc convention, we hence replace all
/** with /* and **/ with */.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix compile warning for frame size over 1024 in gcc 4.4.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add debugfs support to obtain firmware trace, driver trace
and read/write to registers.
- debugfs hierarchy:
/sys/kernel/debug/bfa/host#
where the host number corresponds to the one under /sys/class/scsi_host/host#
- Following are the new debugfs entries added:
drvtrc: collect current driver trace
fwtrc: collect current firmware trace.
fwsave: collect last saved fw trace as a result of firmware crash.
regwr: write one word to chip register
regrd: read one or more words from chip register.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes 3 bugs in vport create/delete.
1) Replace scsi_add_host() with scsi_add_host_with_dma()
2) Fix rmmod hang when there are vports configured. This is due to a race
condition between the workqueue destroy in pci remove context and the vport
delete works being handled. The fix is to use a counter to track the
vport delete work, so that workqueue destroy will not be called until all
configured vports are deleted from workqueue.
3) Fix rmmmod crash when there are PBC vport configured. PBC is not allowed
to be deleted dynamically. However, if someone try to delete it, it leaves the
vport is wrong state. The fix is to restore the vport back to original state
when the attempt to delete pbc vport delete is failed.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added time stamp for fcport stats reset
- Added new fileds to the statistics data structures.
- Typo removal and minor cleanup.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables creating PBC vport.
During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb
callback to add the pbc vport entries into a list. The pbc vport list will be
traversed in the subsequent pci probe process and vport will be created using
fc transport provided vport create function.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
idr is a global resource, protect it with global bfad_mutex.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use pci_iomap() and pci_iounmap() to simplify the code. Remove uncessary #ifdef
check for ia64 (it was added as a workaound for some RHEL 5.x release which
doesn't export iounmap function)
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use duplicate fc transport template for physical and vitual port. Add
vport create/delete/disalbe functions in the transport template of physical
port. Changes to make the vport create/delete function to work under this
framework.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Upgrade the upstream driver from 2.0.0.0 to 2.1.2.1.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfa_ioc_attr_s is a big structure and some times could cause
stack overflow if defined locally, so add specific APIs that
are needed to replace the use of ioc_attr local var.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace enum types with int and rearrange the fields to fix some
alignment issue.
Local var ioc_attr is causing the stack to overflow, so removed the
usage of the local ioc_attr var and now invoking an API to return the
ioc_type.
Fix some AEN issues.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bfad.c & bfad_drv.h:
* Created a kernel thread from pci_probe that does the bfad start
operations after BFA init done on a firmware mismatch.
* The kernel thread on a fw mismatch waits for an event from IOC
call back and is woken up from bfa_cb_init() on BFA init success.
* In normal cases of no firmware mismatch this thread is terminated
in pci_probe.
bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
* Split the lport init to attach time and init time code, so that
proper config attributes are set after firmware mismatch.
bfa_iocfc.c:
* Handle an IOC timer issue, where the IOC timer would expire before
the init completion and send Init fail event to the driver,
however IOC init continues and completes successfully at the later
stage. The bfa and driver were not handling this kind of deferred
init completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kees Cook