Originators of cmd IO typically hold the rtnl or conf_mutex to protect
against a concurrent teardown.
Since qeth_set_offline() already holds the conf_mutex, the main reason
why we still care about cancelling pending cmds is so that they release
the rtnl when we need it ourselves.
So move this step a little earlier into the teardown sequence.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The programming of ucast IPs via qeth_l3_modify_ip() is driven
independently from any of our typical locking mechanisms (eg. detaching
the netdevice, or holding the conf_mutex).
So when we inspect the card state to check whether the required cmd IO
should be deferred, there is no protection against concurrent state
changes.
But by slightly re-ordering the teardown sequence, we can rely on the
ip_lock to sufficiently serialize things:
1. when running concurrently to qeth_l3_set_online(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_recover_ip() will observe the state as CARD_STATE_SOFTSETUP
and not defer the IO.
2. when running concurrently to qeth_l3_set_offline(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_clear_ip_htable() will observe the state as CARD_STATE_DOWN
and defer the IO.
These guarantees in mind, we can now drop the conf_mutex from the
qeth_l3_modify_rxip_vipa() wrapper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the remaining occurences in sysfs code to kstrtouint().
While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate the max number of to-be-parsed characters, and avoid copying
the address sub-string.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
card->ipato is currently protected by the conf_mutex. But most users
also hold the ip_lock - in particular qeth_l3_add_ip().
So slightly expand the sections under ip_lock in a few places (to
effectively cover a few error & no-op cases), and then drop the
conf_mutex where it's no longer needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mcast IP objects are allocated within qeth_l3_add_mcast_rtnl(),
with .ref_counter already set to 1 via qeth_l3_init_ipaddr().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/microchip/lan743x_main.c: In function lan743x_pm_suspend:
`ret` is set but not used. In fact, `pci_prepare_to_sleep` function value should
be the right value of `lan743x_pm_suspend` function, therefore, fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multi packet TX descriptor support for SKBs.
This series introduces some refactoring of the regular TX data path in
mlx5 and adds the Enhanced TX MPWQE feature support. MPWQE stands for
multi-packet work queue element, and it can serve multiple packets,
reducing the PCI bandwidth spent on control traffic. It should improve
performance in scenarios where PCI is the bottleneck, and xmit_more is
signaled by the kernel. The refactoring done in this series also
improves the packet rate on its own.
MPWQE is already implemented in the XDP tx path, this series adds the
support of MPWQE for regular kernel SKB tx path.
MPWQE is supported from ConnectX-5 and onward, for legacy devices we need
to keep backward compatibility for regular (Single packet) WQE descriptor.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE per SKB.
Prior to the final patch "net/mlx5e: Enhanced TX MPWQE for SKBs" that adds
the actual support, Maxim did some refactoring to the tx data path to
split it into stages and smaller helper functions that can be utilized and
reused for both legacy and new MPWQE feature.
Performance testing:
UDP performance is improved in a single stream pktgen test:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 434 -> 329
Cycles per packet: 158 -> 123
Instructions per cycle: 2.75 -> 2.67
TCP and XDP_TX single stream tests show no performance difference.
MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
MPWQE can also reduce CPU load, increasing the packet rate in case of
CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl9pZE0ACgkQSD+KveBX
+j5V/Qf+M0PI/ZyTsOlHbl78Mz7acgGSZTjFBPo0MQ7U0ReY8C25YVDycKazlwwZ
XL8Ip1gV08uDbROB92ozQcDekIyiTyae04ACXa+oCl/lxJydxN5ZDAiJV+bUhb0E
Ti4rBrgPH46FMbKso2XPFxdk9f9krqOLA2Jl7Am+R+W1nYgdBkqumTRXGkDEV8oi
p1YeFb/ldBXS6En/QQAZ89FbHaoV+V4Z2uHhdoWjLPhumgplk14BwRMT0UCRn3IK
6Q8jk55gW7lE9vdhQuOHZeU3SRr2+VcyYii2/htfvdQjsGrBVrAm1gWcF2KrUa6C
VxuDQ1oXh3r/eibnTq/XReadRiGSVg==
=ouzY
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-09-21
Multi packet TX descriptor support for SKBs.
This series introduces some refactoring of the regular TX data path in
mlx5 and adds the Enhanced TX MPWQE feature support. MPWQE stands for
multi-packet work queue element, and it can serve multiple packets,
reducing the PCI bandwidth spent on control traffic. It should improve
performance in scenarios where PCI is the bottleneck, and xmit_more is
signaled by the kernel. The refactoring done in this series also
improves the packet rate on its own.
MPWQE is already implemented in the XDP tx path, this series adds the
support of MPWQE for regular kernel SKB tx path.
MPWQE is supported from ConnectX-5 and onward, for legacy devices we need
to keep backward compatibility for regular (Single packet) WQE descriptor.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE per SKB.
Prior to the final patch "net/mlx5e: Enhanced TX MPWQE for SKBs" that adds
the actual support, Maxim did some refactoring to the tx data path to
split it into stages and smaller helper functions that can be utilized and
reused for both legacy and new MPWQE feature.
Performance testing:
UDP performance is improved in a single stream pktgen test:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 434 -> 329
Cycles per packet: 158 -> 123
Instructions per cycle: 2.75 -> 2.67
TCP and XDP_TX single stream tests show no performance difference.
MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
MPWQE can also reduce CPU load, increasing the packet rate in case of
CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit says:
====================
devlink: Use nla_policy to validate range
This two small patches uses nla_policy to validate user specified
fields are in valid range or not.
Patch summary:
Patch-1 checks the range of eswitch mode field
Patch-2 checks for the port type field. It eliminates a check in
code by using nla policy infrastructure.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use range checking facility of nla_policy to validate port type
attribute input value is valid or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use range checking facility of nla_policy to validate eswitch mode input
attribute value is valid or not.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"No common topic, just assorted fixes"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fuse: fix the ->direct_IO() treatment of iov_iter
fs: fix cast in fsparam_u32hex() macro
vboxsf: Fix the check for the old binary mount-arguments struct
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
-----BEGIN PGP SIGNATURE-----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=ImBG
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes - most of them regression fixes from this cycle, but also
a few stable heading fixes, and a build fix for the included demo tool
since some systems now actually have gettid() available"
* tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
io_uring: fix openat/openat2 unified prep handling
io_uring: mark statx/files_update/epoll_ctl as non-SQPOLL
tools/io_uring: fix compile breakage
io_uring: don't use retry based buffered reads for non-async bdev
io_uring: don't re-setup vecs/iter in io_resumit_prep() is already there
io_uring: don't run task work on an exiting task
io_uring: drop 'ctx' ref on task work cancelation
io_uring: grab any needed state during defer prep
-----BEGIN PGP SIGNATURE-----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=zT03
-----END PGP SIGNATURE-----
Merge tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
- Check kprobe is enabled before unregistering from ftrace as it isn't
registered when disabled.
- Remove kprobes enabled via command-line that is on init text when freed.
- Add missing RCU synchronization for ftrace trampoline symbols removed
from kallsyms.
- Free trampoline on error path if ftrace_startup() fails.
- Give more space for the longer PID numbers in trace output.
- Fix a possible double free in the histogram code.
- A couple of fixes that were discovered by sparse.
-----BEGIN PGP SIGNATURE-----
iIkEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCX2lEchQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qokAAQDphHFTOlgjKi7lF7bc5V1bl/MT1bVo
bJRHV8w2agtXMgD49ElFOl6znXqid3X++0dYZ5/AQgOZXf1rsYS05Pj0Dw==
=+cVX
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Check kprobe is enabled before unregistering from ftrace as it isn't
registered when disabled.
- Remove kprobes enabled via command-line that is on init text when
freed.
- Add missing RCU synchronization for ftrace trampoline symbols removed
from kallsyms.
- Free trampoline on error path if ftrace_startup() fails.
- Give more space for the longer PID numbers in trace output.
- Fix a possible double free in the histogram code.
- A couple of fixes that were discovered by sparse.
* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: init: make xbc_namebuf static
kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
tracing: fix double free
ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
tracing: Make the space reserved for the pid wider
ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
ftrace: Free the trampoline when ftrace_startup() fails
kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()
This commit adds support for Enhanced TX MPWQE feature in the regular
(SKB) data path. A MPWQE (multi-packet work queue element) can serve
multiple packets, reducing the PCI bandwidth on control traffic.
Two new stats (tx*_mpwqe_blks and tx*_mpwqe_pkts) are added. The feature
is on by default and controlled by the skb_tx_mpwqe private flag.
In a MPWQE, eseg is shared among all packets, so eseg-based offloads
(IPSEC, GENEVE, checksum) run on a separate eseg that is compared to the
eseg of the current MPWQE session to decide if the new packet can be
added to the same session.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
UDP pktgen, 64-byte packets, single stream, MPWQE off:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 17.01 Mpps (±0.20 Mpps)
Instructions per packet: 421 -> 429
Cycles per packet: 156 -> 161
Instructions per cycle: 2.70 -> 2.67
UDP pktgen, 64-byte packets, single stream, MPWQE on:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 421 -> 329
Cycles per packet: 156 -> 123
Instructions per cycle: 2.70 -> 2.67
Enabling MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
Enabling MPWQE can also reduce CPU load, increasing the packet rate in
case of CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
Burst size in all pktgen tests is 32.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_txwqe_complete performs some actions that can be taken to separate
functions:
1. Update the flags needed for hardware timestamping.
2. Stop the TX queue if it's full.
Take these actions into separate functions to be reused by the MPWQE
code in the following commit and to maintain clear responsibilities of
functions.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As preparation for the upcoming TX MPWQE support for SKBs, rename struct
mlx5e_xdp_mpwqe to mlx5e_tx_mpwqe and move it above struct mlx5e_txqsq.
This structure will be reused in the regular SQ and in the regular TX
data path. Also rename mlx5e_xdp_xmit_data to mlx5e_xmit_data - it will
be used in the upcoming TX MPWQE flow.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As preparation for the upcoming TX MPWQE for SKBs, create a function
(mlx5e_tx_mpwqe_is_full) to check whether an MPWQE session is full. This
function will be shared by MPWQE code for XDP and for SKBs. Defines are
renamed and moved to make them not XDP-specific.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
TX MPWQE support for SKBs is coming in one of the following patches, and
a single MPWQE can send multiple SKBs. This commit prepares the TX path
code to handle such cases:
1. An additional FIFO for SKBs is added, just like the FIFO for DMA
chunks.
2. struct mlx5e_tx_wqe_info will contain num_fifo_pkts. If a given WQE
contains only one packet, num_fifo_pkts will be zero, and the SKB will
be stored in mlx5e_tx_wqe_info, as usual. If num_fifo_pkts > 0, the SKB
pointer will be NULL, and the SKBs will be stored in the FIFO.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.95 Mpps (±0.15 Mpps) -> 16.96 Mpps (±0.12 Mpps)
Instructions per packet: 429 -> 421
Cycles per packet: 160 -> 156
Instructions per cycle: 2.69 -> 2.70
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Before this patch, mlx5e_ktls_tx_handle_resync_dump_comp checked for
resync_dump_frag_page. It happened for all WQEs without an SKB,
including padding WQEs, and required a function call. Normally, padding
WQEs happen more often than TLS resyncs. Take this check out of the
function and put it to an inline function to save a call on all padding
WQEs.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A constant for the number of DS in an empty WQE (i.e. a WQE without data
segments) is needed in multiple places (normal TX data path, MPWQE in
XDP), but currently we have a constant for XDP and an inline formula in
normal TX. This patch introduces a common constant.
Additionally, mlx5e_xdp_mpwqe_session_start is converted to use struct
assignment, because the code nearby is touched.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Use MLX5E_XDP_MPW_MAX_WQEBBS to reserve space for a MPWQE, because it's
actually the maximal size a MPWQE can take.
Reorganize the logic that checks when to close the MPWQE session:
1. Put all checks into a single function.
2. When inline is on, make only one comparison - if it's false, the less
strict one will also be false. The compiler probably optimized it out
anyway, but it's clearer to also reflect it in the code.
The MLX5E_XDP_INLINE_WQE_* defines are also changed to make the
calculations more correct from the logical point of view. Though
MLX5E_XDP_INLINE_WQE_MAX_DS_CNT used to be 16 and didn't change its
value, the calculation used to be DIV_ROUND_UP(max inline packet size,
MLX5_SEND_WQE_DS), and the numerator should have included sizeof(struct
mlx5_wqe_inline_seg).
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
A huge function mlx5e_sq_xmit was split into several to achieve multiple
goals:
1. Reuse the code in IPoIB.
2. Better intergrate with TLS, IPSEC, GENEVE and checksum offloads. Now
it's possible to reserve space in the WQ before running eseg-based
offloads, so:
2.1. It's not needed to copy cseg and eseg after mlx5e_fill_sq_frag_edge
anymore.
2.2. mlx5e_txqsq_get_next_pi will be used instead of the legacy
mlx5e_fill_sq_frag_edge for better code maintainability and reuse.
3. Prepare for the upcoming TX MPWQE for SKBs. It will intervene after
mlx5e_sq_calc_wqe_attr to check if it's possible to use MPWQE, and the
code flow will split into two paths: MPWQE and non-MPWQE.
Two high-level functions are provided to send packets:
* mlx5e_xmit is called by the networking stack, runs offloads and sends
the packet. In one of the following patches, MPWQE support will be added
to this flow.
* mlx5e_sq_xmit_simple is called by the TLS offload, runs only the
checksum offload and sends the packet.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 16.95 Mpps (±0.15 Mpps)
Instructions per packet: 434 -> 429
Cycles per packet: 158 -> 160
Instructions per cycle: 2.75 -> 2.69
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz (x86_64)
NIC: Mellanox ConnectX-6 Dx
GCC 10.2.0
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move mlx5e_tx_wqe_inline_mode from en/txrx.h to en_tx.c as it's only
used there.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Struct assignment guarantees that all fields of the structure are
initialized (those that are not mentioned are zeroed). It makes code
mode robust and reduces chances for unpredictable behavior when one
forgets to reset some field and it holds an old value from previous
iterations of using the structure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As preparation for the next patch, don't increase ihs to calculate
ds_cnt and then decrease it, but rather calculate the intermediate value
temporarily. This code has the same amount of arithmetic operations, but
now allows to split out ds_cnt calculation, which will be performed in
the next patch.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Vladimir Oltean says:
====================
Fix broken tc-flower rules for mscc_ocelot switches
All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl9pQ8EACgkQSD+KveBX
+j7I2wf/cu9W3mC8sNeJaZKIbJ+H6KhgZsGbeLud5tFscjcf5IaCpR97hyeZPfEG
doNRtcsT9Pj5YJn458L/p+zTVeWOuaOGPMsV8pdP/8OlFzjJW/rGXnBrEUt0ehkS
Sa//xGD6V8+nW9Z34fwQqrrqJeZik3H9V/RkriZUTsJ/zR/otLF3fVOQFwrS9Ka2
/dl1ERFepjBWupY39PSMFS2S2BZ6LYY8G/ewgHKeexbqLykxU27P3+mFz46YPmP6
jdIMmvo+fuPqyu9Tjtg6pGjYpCWttnBBtDmeSg+ewf61qW4mSemJzfGcbZYY2XT6
CxRsm4aTJ5COTEx05JFOqIhpP5LuAA==
=Hcsv
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-09-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.
Cc: Steven Liu <steven.liu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock only needed when accessing the channel's icosq, grab the lock
after the buf allocation in resync_post_get_progress_params() to avoid
kzalloc(GFP_KERNEL) in atomic context.
Fixes: 0419d8c9d8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Using synchronize_rcu() is sufficient to wait until running NAPI quits.
See similar upstream fix with detailed explanation:
("net/mlx5e: Use synchronize_rcu to sync with NAPI")
This change also fixes a possible use-after-free as the NAPI
might be already released at this stage.
Fixes: 0419d8c9d8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The set of TLS TX global SW counters in mlx5e_tls_sw_stats_desc
is updated from all rings by using atomic ops.
This set of stats is used only in the FPGA TLS use case, not in
the Connect-X TLS one, where regular per-ring counters are used.
Do not expose them in the Connect-X use case, as this would cause
counter duplication. For example, tx_tls_drop_no_sync_data would
appear twice in the ethtool stats.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".
Fix it to work with the correct group by extracting it from the caller's
profile.
Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.
Fixes: 8a236b1514 ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.
Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".
Fixes: f62b8bb8f2 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.
Fixes: 88f30bbcba ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.
Fix by adding FW capability check before creating peer groups/rule.
Fixes: ac004b8321 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add missing mapping remove call when removing ct rule,
as the mapping was allocated when ct rule was adding with ct_label.
Also there is a missing mapping remove call in error flow.
Fixes: 54b154ecfb ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When deleting vxlan flow rule under multipath, tun_info in parse_attr is
not freed when the rule is not ready.
Fixes: ef06c9ee89 ("net/mlx5e: Allow one failure when offloading tc encap rules under multipath")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As described in the previous commit, napi_synchronize doesn't quite fit
the purpose when we just need to wait until the currently running NAPI
quits. Its implementation waits until NAPI is not running by polling and
waiting for 1ms in between. In cases where we need to deactivate one
queue (e.g., recovery flows) or where we deactivate them one-by-one
(deactivate channel flow), we may get stuck in napi_synchronize forever
if other queues keep NAPI active, causing a soft lockup. Depending on
kernel configuration (CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC), it may result
in a kernel panic.
To fix the issue, use synchronize_rcu to wait for NAPI to quit, and wrap
the whole NAPI in rcu_read_lock.
Fixes: acc6c5953a ("net/mlx5e: Split open/close channels to stages")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Julian Wiedmann