Add initial DTSI for RZ/G2{L,LC} SoC's.
File structure:
r9a07g044.dtsi => RZ/G2L family SoC common parts
r9a07g044l1.dtsi => RZ/G2L R9A07G044L1 SoC specific parts
r9a07g044l2.dtsi => RZ/G2L R9A07G044L2 SoC specific parts
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Although the schematics of Pine A64-LTS and SoPine Baseboard shows both
the RX and TX internal delay are enabled, they're using the same broken
RTL8211E chip batch with Pine A64+, so they should use TXID instead, not
ID.
In addition, by checking the real components soldered on both a SoPine
Baseboard and a Pine A64-LTS, RX delay is not enabled (GR69 soldered and
GR70 NC) despite the schematics says it's enabled. It's a common
situation for Pine64 boards that the NC information on schematics is not
the same with the board.
So the RGMII delay mode should be TXID on these boards.
Fixes: c2b111e59a ("arm64: dts: allwinner: A64 Sopine: phy-mode rgmii-id")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210609083843.463750-1-icenowy@aosc.io
Add a basic GPU node for mt8183, as well as OPP table.
Note that with the current panfrost driver, devfreq is not
actually functional, as the we do not have platform-specific
support for >1 supplies. Also, we are missing code to handle
frequency change, as the GPU frequency needs to be switched
away to a stable 26Mhz clock during the transition.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20210521200038.v14.1.I9f45f5c1f975422d58b5904d11546349e9ccdc94@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add tboard thermal zones.
The tboard thermal sensors are a kind of NTC sensors which are located
on PCB board to correlate the temperature of the case (Tskin).
pull-up voltage: 1800 mv
pull-up resistor: 75K
Vsense = pull-up voltage * Rntc / ( pull-up resistor + Rntc )
AuxIn = Vsense * 4096 / 1500
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Ben Tseng <ben.tseng@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210604093755.13288-1-ben.tseng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a 'cbas' device node for supporting tablet mode switch in
kukui devices.
Kukui platforms with detacheable base have an additional input
device under cros-ec, which reports SW_TABLET_MODE regarding
its base state (e.g. base flipped or detached).
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210609032554.2443675-1-ikjn@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds a reference to the dts of the Raspberry Pi 400,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://lore.kernel.org/r/1622981777-5023-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
AM642-SK has no PCIe slot. Disable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-6-kishon@ti.com
AM642 EVM has a x4 lane PCIe connector. Enable PCIe in RC mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-4-kishon@ti.com
AM64 has one PCIe instance which can be configured in either
host mode (RC) or device mode (EP). Add PCIe DT node for host
mode and device mode here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-3-kishon@ti.com
AM64 has one SERDES 10G instance. Add SERDES DT node for it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603142251.14563-2-kishon@ti.com
Commit 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board:
Configure the PCIe instances") and
commit 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed
support for USB0") added PHY DT nodes with node name as "link"
However nodes with #phy-cells should be named 'phy' as discussed in [1].
Re-name subnodes of serdes in J721E to 'phy'.
[1] -> http://lore.kernel.org/r/20200909203631.GA3026331@bogus
Fixes: 66db854b1f ("arm64: dts: ti: k3-j721e-common-proc-board: Configure the PCIe instances")
Fixes: 02c35dca2b ("arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-5-kishon@ti.com
Use external clock for all the SERDES used by PCIe controller. This will
make the same clock used by the local SERDES as well as the clock
provided to the PCIe connector.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-4-kishon@ti.com
Add #clock-cells property to serdes DT node since the serdes is also now
modeled as a clock provider and include the input clocks "pll0_refclk"
and "pll1_refclk" which are parents to the clocks modeled by serdes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-3-kishon@ti.com
Rename the external refclk inputs to the SERDES from
dummy_cmn_refclk/dummy_cmn_refclk1 to cmn_refclk/cmn_refclk1
respectively. Also move the external refclk DT nodes outside the
cbass_main DT node. Since in j721e common processor board, only the
cmn_refclk1 is connected to 100MHz clock, fix the clock frequency.
Fixes: afd094ebe6 ("arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210603143427.28735-2-kishon@ti.com
Enable support for audio-graph based sound card on Jetson Xavier NX.
Following I/O interfaces are enabled.
- I2S3 and I2S5
- DMIC1, DMIC2 and DMIC4
- DSPK1 and DSPK2
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This enables the adreno-specific SMMU path that sets HUPCF so
(user-managed) page faults don't wedge the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-2-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
The ICSSGs on K3 J721E SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-j721e-main.dtsi
file by default, and disabled in the existing J721E board dts
file. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-3-s-anna@ti.com
The ICSSGs on K3 AM65x SoCs contain an MDIO controller that can
be used to control external PHYs associated with the Industrial
Ethernet peripherals within each ICSSG instance. The MDIO module
used within the ICSSG is similar to the MDIO Controller used
in TI Davinci SoCs. A bus frequency of 1 MHz is chosen for the
MDIO operations.
The nodes are added and enabled in the common k3-am65-main.dtsi
file by default, and disabled in the existing AM65 board dts
files. These nodes need pinctrl lines, and so should be enabled
only on boards where they are actually wired and pinned out for
ICSSG Ethernet. Any new board dts file should disable these if
they are not sure.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[s-anna@ti.com: move the disabled status to board dts files]
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210601150032.11432-2-s-anna@ti.com
UHS-I speed modes are supported in AM65 S.R. 2.0 SoC[1].
Add support by removing the no-1-8-v tag and including the voltage
regulator device tree nodes for power cycling.
However, the 4 bit interface of AM65 SR 1.0 cannot be supported at 3.3 V or
1.8 V because of erratas i2025 and i2026 [2]. As the SD card is the primary
boot mode for development usecases, continue to enable SD card and disable
UHS-I modes in it to minimize any ageing issues happening because of
erratas.
k3-am6528-iot2050-basic and k3-am6548-iot2050-advanced boards use S.R. 1.0
version of AM65 SoC. Therefore, add no-1-8-v in sdhci1 device tree node of
the common iot2050 device tree file.
[1] - https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf, section 12.3.6.1.1
[2] - https://www.ti.com/lit/er/sprz452e/sprz452e.pdf
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210529033749.6250-1-a-govindraju@ti.com
"make dtbs_check":
arm64/boot/dts/renesas/r8a779a0-falcon.dt.yaml: interrupt-controller@f1000000: 'power-domains' does not match any of the regexes: '^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$', '^gic-its@', '^interrupt-controller@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml
Remove the "power-domains" property, as the GIC on R-Car V3U is
always-on, and not part of a clock domain.
Fixes: 834c310f54 ("arm64: dts: renesas: Add Renesas R8A779A0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/a9ae5cbc7c586bf2c6b18ddc665ad7051bd1d206.1622560236.git.geert+renesas@glider.be
Microsoft Surface Duo is based on SM8150 chipset. This new Device Tree
is a copy of sm8150-mtp with a the addition of the volume up key and
relevant i2c nodes.
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210603122923.1919624-1-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some SC7180 based boards do not have external pull-up for cd-gpio.
Set this pin to internal pull-up for sleep config to avoid frequent
regulator toggle events.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210602121313.v3.2.I52f30ddfe62041b7e6c3c362f0ad8f695ac28224@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have a Samsung S3FWRN5 NFC chip that
works quite well with the s3fwrn5 driver in the Linux NFC subsystem.
The clock setup for the NFC chip is a bit special (although this
seems to be a common approach used for Qualcomm devices with NFC):
The NFC chip has an output GPIO that is asserted whenever the clock
is needed to function properly. On the A3/A5 this is wired up to
PM8916 GPIO2, which is then configured with a special function
(NFC_CLK_REQ or BB_CLK2_REQ).
Enabling the rpmcc RPM_SMD_BB_CLK2_PIN clock will then instruct
PM8916 to automatically enable the clock whenever the NFC chip
requests it. The advantage is that the clock is only enabled when
needed and we don't need to manage it ourselves from the NFC driver.
Note that for some reason Samsung decided to connect the I2C pins
to GPIOs where no hardware I2C bus is available, so we need to
fall back to software bit-banging with i2c-gpio.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 use a Richtek RT5033 PMIC as battery
fuel gauge, charger, flash LED and for some regulators. For now,
only add the fuel gauge/battery device to the device tree,
so we can check the remaining battery percentage.
The other RT5033 drivers need some more work first before
they can be used properly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On the Samsung Galaxy A5 the touch key is supplied by a single fixed
regulator (enabled via GPIO 97) that supplies both MCU and LED.
Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The touch key MCU and LED is supplied by two separate fixed regulators
that can be enabled through GPIO 86 and 60. Add them to the device tree.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
[stephan: extend commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Samsung Galaxy A3/A5 both have two capacitive touch keys,
connected to an ABOV MCU. It implements the same interface as
implemented by the tm2-touchkey driver and works just fine with
the coreriver,tc360-touchkey compatible. It's probably actually some
Samsung-specific interface that they implement with different MCUs.
Note that for some reason Samsung decided to connect this to GPIOs
where no hardware I2C bus is available, so we need to fall back
to software bit-banging using i2c-gpio.
The vdd/vcc-supply is board-specific and will be added separately
for a3u/a5u.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a thermal zone for the pm6150 on-die temperature. The system should
try to shut down orderly when the temperature reaches the critical trip
point at 115°C, otherwise the PMIC will perform a HW power off at 145°C.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210603081215.v2.1.Id4510e9e4baaa3f6c9fdd5cdf4d8606e63c262e3@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
-----BEGIN PGP SIGNATURE-----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=veTm
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux into arm/fixes
Devicetree fixes for TI K3 platforms for v5.13 merge window:
These minor fixes include:
* Fixups for device tree discovered during yaml conversion
* Fixups for missing dma-coherent property in j7200
* Removal of camera sensor node from am65 evm dts to overlay
as camera sensor boards are variable.
* tag 'ti-k3-dt-fixes-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
arm64: dts: ti: k3*: Introduce reg definition for interrupt routers
arm64: dts: ti: k3-am65|j721e|am64: Map the dma / navigator subsystem via explicit ranges
arm64: dts: ti: k3-*: Rename the TI-SCI node
arm64: dts: ti: k3-am65-wakeup: Drop un-necessary properties from dmsc node
arm64: dts: ti: k3-am65-wakeup: Add debug region to TI-SCI node
arm64: dts: ti: k3-*: Rename the TI-SCI clocks node name
arm64: dts: ti: j7200-main: Mark Main NAVSS as dma-coherent
arm64: dts: ti: k3-am654-base-board: remove ov5640
Link: https://lore.kernel.org/r/20210518115634.467vgpbzplal5kou@obituary
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmCu8p4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7k+Qf9Ek/atJBjaaVzhbGFQ8HRnDOk4U5J
dR0GbXKSN1zXjDLSBOBRyNcVn2T6lp4LwwYoleC2qG6MNoe6+y7fk1oRdvjkGjRO
ZYfZT/JJl187IN6JsxR8VhRmmcI5/C3bihMbpKoLdHcPGbwC4relfSy99Io94Xfk
CVn3PTxBA4KfoDq/+EiA9HkQ/HwQh/y7KD5yVd6OtLkt9awT1hYW1ttVefp95nAK
5+zTm0Z14U8aGm+wo8jywvSyeXiuMeWDUrweo05XcaHWfcv3T0Wni7tgS2pluxqa
lCMsNQBsZDTk6fUWxqPjjAEl6ks8N1H9L7YIGpq1dOCSYFUqI3jCmkhrFQ==
=5vQk
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.13:
- Fix missing-prototypes warning of 'imx27_pm_init' in i.MX27 platform
pm code.
- A couple of patches from Fabio Estevam to fix 'tuning-step' property
in imx7d-meerkat96 and imx7d-pico DT.
- Fix '#gpio-cells' of nxp,pca8574 device in imx6qdl-emcon-avari DT.
- A couple of patches from Lucas Stach to fix regulator and voltage for
imx8mq-zii-ultra board.
- Add missing regulators for imx6q-dhcom to avoid possible instability
issues.
- Fix memory-controller settings for fsl-ls1028a DT.
- Fix RGMII clock and voltage for a couple of fsl-ls1028a-kontron-sl28
boards.
- Fix RGMII connection to QCA8334 switch for imx6dl-yapp4 board.
* tag 'imx-fixes-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cells
ARM: dts: imx7d-pico: Fix the 'tuning-step' property
ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' property
arm64: dts: freescale: sl28: var1: fix RGMII clock and voltage
arm64: dts: freescale: sl28: var4: fix RGMII clock and voltage
ARM: imx: pm-imx27: Include "common.h"
arm64: dts: zii-ultra: fix 12V_MAIN voltage
arm64: dts: zii-ultra: remove second GEN_3V3 regulator instance
arm64: dts: ls1028a: fix memory node
ARM: dts: imx6q-dhcom: Add PU,VDD1P1,VDD2P5 regulators
ARM: dts: imx6dl-yapp4: Fix RGMII connection to QCA8334 switch
Link: https://lore.kernel.org/r/20210527011758.GD8194@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
The Rockchip RK3308 features an integrated USB 2.0 phy, an USB OTG
controller and OHCI/EHCI interfaces.
This patch adds all of those to the RK3308 dtsi and thereby enables USB
support on the RK3308.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pattern: "^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$"
in phy-provider.yaml has required "#phy-cells" for phy nodes.
The "phy-cells" in rockchip-inno-usb2 nodes are located in subnodes.
Rename the nodename to pattern "usb2phy@[0-9a-f]+$" to prevent
notifications.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210601164800.7670-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the new rk817 codec driver to the Odroid Go Advance.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20210519203754.27184-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We don't need to register smi_common as syscon. Also add required
property power-domains for this node.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210601040014.2970805-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Adds label for MI2S secondary block to allow follower projects to override
for the four speaker support which uses I2S SD1 line on gpio52 pin.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20210601022117.4071117-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The first UART controller in "Everything-Else" power domain, usually used
for Bluetooth HCI has 128bytes FIFO depth.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-4-narmstrong@baylibre.com
The sc7280 IDP board is also called senor in the Chrome OS builds.
Add the "google,senor" compatible so coreboot/depthcharge knows what
device tree blob to pick
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1619674827-26650-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move rmtfs memory region so that it does not overlap with system
RAM (kernel data) when KAsan is enabled. This puts rmtfs right
after mba_mem which is not supposed to increase beyond 0x94600000
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Link: https://lore.kernel.org/r/20210514113430.1.Ic2d032cd80424af229bb95e2c67dd4de1a70cb0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the video, gpu, display, lpass clock controller
device nodes for SC7280 SoC.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1618020280-5470-3-git-send-email-tdas@codeaurora.org
[bjorn: Dropped includes, as they are not present in v5.13-rc1]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add ADC and thermal monitor configuration for skin temperature,
plus a thermal zone that monitors the skin temperature and uses
the big cores as cooling devices.
CoachZ rev1 is stuffed with an incompatible thermistor for the
skin temperature, disable the thermal zone for rev1 to avoid
the use of bogus temperature values.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210414111007.v1.1.I1a438604a79025307f177347d45815987b105cb5@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As per Dmitry Baryshkov [1]:
a) The 2nd "reg" should be 0x3c because "Offset 0x38 is
USB3_DP_COM_REVISION_ID3 (not used by the current driver though)."
b) The 3rd "reg" "is a serdes region and qmp_v3_dp_serdes_tbl contains
registers 0x148 and 0x154."
I think because the 3rd "reg" is a serdes region we should just use
the same size as the 1st "reg"?
[1] https://lore.kernel.org/r/ee5695bb-a603-0dd5-7a7f-695e919b1af1@linaro.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Fixes: 58fd7ae621 ("arm64: dts: qcom: sc7180: Update dts for DP phy inside QMP phy")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210315103836.1.I9a97120319d43b42353aeac4d348624d60687df7@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use sm8250 compatibles instead of sdm845 compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210329120051.3401567-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be enabling HPD
when it isn't supposed to be used. Presumably this board isn't using hpd
on the bridge.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Steev Klimaszewski <steev@kali.org>
Fixes: 956e9c85f4 ("arm64: dts: qcom: c630: Define eDP bridge and panel")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324231424.2890039-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210324204836.29668-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715, 5f8d3ab136, which is needed to allow angler to boot after
3edfb7bd76 ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac7 ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the compatible to make the driver probe and tell the
driver where to look for the "xo" clock to make sure everything
works.
Then we get a happy (eh, happier) 8996:
somainline-sdcard:/home/konrad# cat /sys/kernel/debug/clk/pwrcl_pll/clk_rate
1152000000
Don't backport without "arm64: dts: qcom: msm8996: Add CPU opps", as
the system fails to boot without consumers for these clocks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527192958.775434-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the operating points capabilities of the kryo CPUs, that can be
used for frequency scaling. There are two differents operating point
tables, one for the big cluster and one for the LITTLE cluster.
This frequency scaling support can then be used as a passive cooling
device (cpufreq cooling device).
Only add nominal fmax for now, since there is no dynamic control of
VDD APC (s11..) which is statically set at its nominal value.
Original patch link: https://patchwork.kernel.org/project/linux-arm-msm/patch/1595253740-29466-6-git-send-email-loic.poulain@linaro.org/
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[konrad: drop the thermals part, rebase and remove spaces within <>]
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
CoachZ rev3 uses a 100k NTC thermistor for the charger temperatures,
instead of the 47k NTC that is stuffed in earlier revisions. Add .dts
files for rev3.
The 47k NTC currently isn't supported by the PM6150 ADC driver.
Disable the charger thermal zone for rev1 and rev2 to avoid the use
of bogus temperature values.
This also gets rid of the explicit DT files for rev2 and handles
rev2 in the rev1 .dts instead. There was some back and forth
downstream involving the 'dmic_clk_en' pin, after that was sorted
out the DT for rev1 and rev2 is the same.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.3.I95b8a63103b77cab6a7cf9c150f0541db57fda98@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only kernel visible change with respect to rev2 is that pompom
rev3 changed the charger thermistor from a 47k to a 100k NTC to use
a thermistor which is supported by the PM6150 ADC driver.
Disable the charger thermal zone for pompom rev1 and rev2 to avoid
the use of bogus temperature values from the unsupported thermistor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.2.I4138c3edee23d1efa637eef51e841d9d2e266659@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit f73558cc83d1 ("arm64: dts: qcom: sc7180: Disable charger
thermal zone for lazor") disables the charger thermal zone for
specific lazor revisions due to an unsupported thermistor type.
The initial idea was to disable the thermal zone for older
revisions and leave it enabled for newer ones that use a
supported thermistor. Finally the thermistor won't be changed
on newer revisions, hence the thermal zone should be disabled
for all lazor (and limozeen) revisions. Instead of disabling
it per revision do it once in the shared .dtsi for lazor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.1.I6d587e7ae72a5a47253bb95dfdc3158f8cc8a157@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We had introduced the QUP-CORE ICC path to put proxy votes from
QUP wrapper on behalf of earlycon, if other users of QUP-CORE turn
off this clock before the real console is probed, unclocked access
to HW was seen from earlycon.
With ICC sync state support proxy votes are no longer need as ICC
will ensure that the default bootloader votes are not removed until
all it's consumer are probed.
We can safely remove ICC path for QUP-CORE clock from QUP wrapper
device.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210324101836.25272-3-rojay@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1
arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
Fix by correcting to the correct address as given in reg node
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210513060733.382420-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With this patch, DMA has a chance of probing and doing something
useful.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210417061951.2105530-3-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The speedbin value blown in the efuse is used to determine is used to
determine the voltage and frequency value for different IPs, including
GPU, CPUs... So it's really not a gpu specific information.
This patch simply renames 'gpu_speed_bin' node to 'speedbin'.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the QUSB USB PHY-s has been left enabled by
default, this is probably just a mistake as other
USB PHY-s are disabled by default.
It makes no sense to have it enabled by default as
not all board implement USB ports, so disable it.
Reviewed-by: Kathiravan T <kathirav@codeaurora.org>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20210526150125.1816335-1-robimarko@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.
Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Enable work around feature built into the controller to address issue with
RX Sensitivity for USB2 PHY.
Fixes: 6197d7139d ("arm64: dts: ti: k3-j7200-main: Add USB controller")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210512153308.5840-1-a-govindraju@ti.com
The current scheme for audio card names is suboptimal because it causes
the automatically generated names (for ID and driver) to be truncated,
which in turn can cause conflicts.
Introduce a new scheme which reuses the board model for the names and
appends the "HDA" and "APE" suffixes for the HDA and APE, respectively.
As a side-effect these suffixes end up being used as the ID of the SoC
sound cards which makes it easy for users to select them when using the
ALSA command-line utilities, for example.
As a separate measure, the driver name for the cards is now set by the
corresponding audio driver (either tegra-hda or tegra-ape), making it a
more useful identifier than the currently normalized card name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the device-tree node for the PMU device on Tegra194. This also
fixes the following warning that is observed on booting Tegra194.
ERR KERN kvm: pmu event creation failed -2
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable audio capture frontends and a tdm decoder.
This makes it possible to loopback the audio played on the hdmi codec,
which is the only output interface at the moment.
Of course, one TODDR device would be enough to do that but since
the 3 FRDDRs are enabled on the playback side, let's do the same on the
capture side.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429084253.59692-1-jbrunet@baylibre.com
As the name implies, the USB2 controller should only operate at
USB2 speeds. Make sure it does just that by pinning it to USB
High-Speed (USB2) mode.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210525200246.118323-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add channel nodes for the on die temperatures of PMICS
pmk8350, pm8350, pmr735a and pmr735b.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1621937466-1502-11-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-9-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-7-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add gpio ranges and correct the compatible to add
"qcom,spmi-gpio" as this pmic is on spmi bus.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Link: https://lore.kernel.org/r/1621937466-1502-5-git-send-email-skakit@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable Venus by default to allow booting without closed firmware and
enable it on the boards that didn't previously disable it. This commit
brings no functional difference.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-7-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Disable them by default to allow for booting without a display
and proprietary firmware. Then, enable them on boards that didn't
previously disable them. Hence, this commit brings no functional
difference.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-6-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Set the tcsr_mutex_regs size to 0x40000 to allow for accessing
all required registers that will be needed to support modem.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-3-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QUP and UART names start from 1. There are 6 QUPs and 2 UARTs
per BLSP. Let's not further confuse programmers by stating
otherwise.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to prepare for feature development, the DTs
have to be workable with.. To achieve that:
- Rename msmgpio to tlmm (consistency with newer DTs)
- Rid msm8996-pins.dtsi and add the contents to msm8996.dtsi
- Modernize the pin nodes, make them more concise
- Add generic pin configuration for some hardware
- Fix up some names in preparation for BLSP/UART name cleaning..
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210228130831.203765-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qcom camera driver allocates the ICP firmware memory
dynamically, so the carveout region is unnecessary.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://lore.kernel.org/r/20210525133242.188603-1-senozhatsky@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds audio support for Xiaomi Poco F1 phone. Phone's primary
Mic and 3.5mm Headphone jack are handled through the SDM845 sound card
and WCD9340 codec.
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
Link: https://lore.kernel.org/r/BN6PR2001MB17966ED1D787FA3F4B90A1A7D95B9@BN6PR2001MB1796.namprd20.prod.outlook.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The rmtfs_mem region is a weird one, downstream allocates it
dynamically, and supports a "qcom,guard-memory" property which when set
will reserve 4k above and below the rmtfs memory.
A common from qcom 4.9 kernel msm_sharedmem driver:
/*
* If guard_memory is set, then the shared memory region
* will be guarded by SZ_4K at the start and at the end.
* This is needed to overcome the XPU limitation on few
* MSM HW, so as to make this memory not contiguous with
* other allocations that may possibly happen from other
* clients in the system.
*/
When the kernel tries to touch memory that is too close the
rmtfs region it may cause an XPU violation. Such is the case on the
OnePlus 6 where random crashes would occur usually after boot.
Reserve 4k above and below the rmtfs_mem to avoid hitting these XPU
Violations.
This doesn't entirely solve the random crashes on the OnePlus 6/6T but
it does seem to prevent the ones which happen shortly after modem
bringup.
Fixes: 288ef8a426 ("arm64: dts: sdm845: add oneplus6/6t devices")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210502014146.85642-4-caleb@connolly.tech
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The RZ/G2 boards expect there to be an external clock reference for
USB2 EHCI controllers. For the Beacon boards, this reference clock
is controlled by a programmable versaclock. Because the RZ/G2
family has a special clock driver when using an external clock,
the third clock reference in the EHCI node needs to point to this
special clock, called usb2_clksel.
Since the usb2_clksel does not keep the usb_extal clock enabled,
the 4th clock entry for the EHCI nodes needs to reference it to
keep the clock running and make USB functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The USB extal clock reference isn't associated to a crystal, it's
associated to a programmable clock, so remove the extal reference,
add the usb2_clksel. Since usb_extal is referenced by the versaclock,
reference it here so the usb2_clksel can get the proper clock speed
of 50MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210513114617.30191-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Condor, the VCC is connected to
3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux
to match the bus, which is always operating in 1.8V mode.
While at it, deduplicate the pinmux entries, which are now the same for
both default and UHS modes. We still need the two pinctrl entries to
match the bindings though.
Thanks to Marek Vasut for this description from commit 5f65328df3
("arm64: dts: renesas: Switch eMMC bus to 1V8 on Salvator-X and ULCB").
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210419143858.39401-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The AVB reference clock assumes an external clock that runs
automatically. Because the Versaclock is wired to provide the
AVB refclock, the device tree needs to reference it in order for the
driver to start the clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210224115146.9131-5-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The bindings have been updated to support two clocks.
Add a clock-names list in the device tree with fck in it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224115146.9131-3-aford173@gmail.com
[geert: Update new r8a779a0.dtsi]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the "PinePhone" name to the sound card: this will make
upstreaming an ALSA UCM config easier as we can use a unique name.
It also avoids an issue where the default card name is truncated.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: Split out change, updated commit message]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-8-samuel@sholland.org
During hardware validation it was noticed that the clock isn't
continuously enabled when there is no link. This is because the 125MHz
clock is derived from the internal PLL which seems to go into some kind
of power-down mode every once in a while. The LS1028A expects a contiuous
clock. Thus enable the PLL all the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
This fix is for the freescale/fsl-ls1028a-kontron-sl28-var1.dts.
Fixes: 642856097c ("arm64: dts: freescale: sl28: add variant 1")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
During hardware validation it was noticed that the clock isn't
continuously enabled when there is no link. This is because the 125MHz
clock is derived from the internal PLL which seems to go into some kind
of power-down mode every once in a while. The LS1028A expects a contiuous
clock. Thus enable the PLL all the time.
Also, the RGMII pad voltage is wrong. It was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
This fix is for the freescale/fsl-ls1028a-kontron-sl28-var4.dts.
Fixes: 815364d042 ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As this is a fixed regulator on the board there was no harm in the wrong
voltage being specified, apart from a confusing reporting to userspace.
Fixes: 4a13b3bec3 ("arm64: dts: imx: add Zii Ultra board support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When adding the sound support a second instance of the GEN_3V3 regulator was
added by accident. Remove it and point the consumers to the first instance.
Fixes: 663a5b5efa ("arm64: dts: zii-ultra: add sound support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While enabling EDAC support for the LS1028A it was discovered that the
memory node has a wrong endianness setting as well as a wrong interrupt
assignment. Fix both.
This was tested on a sl28 board. To force ECC errors, you can use the
error injection supported by the controller in hardware (with
CONFIG_EDAC_DEBUG enabled):
# enable error injection
$ echo 0x100 > /sys/devices/system/edac/mc/mc0/inject_ctrl
# flip lowest bit of the data
$ echo 0x1 > /sys/devices/system/edac/mc/mc0/inject_data_lo
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are no sub-mailbox devices defined currently for both the
IOT2050 boards. These are usually dictated by the firmwares running
on the R5F remote processors and the applications they provide.
Defining the actual sub-mailboxes will also dictate the interrupts
the clusters will use for interrupts on the Cortex-A53 cores.
Disable all of the Mailbox clusters until the sub-mailboxes are
defined and used. This fixes the warnings around the missing
interrupts with the upcoming conversion of the OMAP Mailbox binding
to YAML format.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210514212016.3153-1-s-anna@ti.com
Only a small number of fixes so far, including some that I had applied
during the merge window, so this is based on the original merge of the
other branches.
- The largest change is a fix for a reference counting bug in
the AMD TEE driver.
- Neil Armstrong now co-maintains Amlogic SoC support
- Two build warning fixes for renesas device tree files
- A sign expansion bug for optee
- A DT binding fix for a mismerge
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=w6Zu
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a small number of fixes so far, including some that I had applied
during the merge window, so this is based on the original merge of the
other branches.
- The largest change is a fix for a reference counting bug in the AMD
TEE driver.
- Neil Armstrong now co-maintains Amlogic SoC support
- Two build warning fixes for renesas device tree files
- A sign expansion bug for optee
- A DT binding fix for a mismerge"
* tag 'arm-soc-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: npcm: wpcm450: select interrupt controller driver
MAINTAINERS: ARM/Amlogic SoCs: add Neil as primary maintainer
tee: amdtee: unload TA only when its refcount becomes 0
dt-bindings: nvmem: mediatek: remove duplicate mt8192 line
firmware: arm_scmi: Remove duplicate declaration of struct scmi_protocol_handle
firmware: arm_scpi: Prevent the ternary sign expansion bug
arm64: dts: renesas: Add port@0 node for all CSI-2 nodes to dtsi
arm64: dts: renesas: aistarvision-mipi-adapter-2.1: Fix CSI40 ports
Change the node name of the UART devices to match
"^serial(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:
- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210516163523.9484-2-amadeus@jmu.edu.cn
The RK3308 SoC has a gmac with only the RMII interface exposed. This
commit adds it to the RK3308 dtsi.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt routers are memory mapped peripherals, that are organized
in our dts bus hierarchy to closely represents the actual hardware
behavior.
However, without explicitly calling out the reg property, using
2021.03+ dt-schema package, this exposes the following problem with
dtbs_check:
/arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000:
interrupt-controller0: {'type': 'object'} is not allowed for
{'compatible': ['ti,sci-intr'], .....
Even though we don't use interrupt router directly via memory mapped
registers and have to use it via the system controller, the hardware
block is memory mapped, so describe the base address in device tree.
This is a valid, comprehensive description of hardware and permitted
by the existing ti,sci-intr schema.
Reviewed-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210511194821.13919-1-nm@ti.com
Instead of using empty ranges property, lets map explicitly the address
range that is mapped onto the dma / navigator subsystems (navss/dmss).
This is also exposed via the dtbs_check with dt-schema newer than
2021.03 version by throwing out following:
arch/arm64/boot/dts/ti/k3-am654-base-board.dt.yaml: bus@100000: main-navss:
{'type': 'object'} is not allowed for
{'compatible': ['simple-mfd'], '#address-cells': [[2]], .....
This has already been correctly done for J7200, however was missed for
other k3 SoCs. Fix that oversight.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210510145429.8752-1-nm@ti.com
Lets rename the node name of TI-SCI node to be system-controller as it
is a better standardized name for the function that TI-SCI plays in the
SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-5-nm@ti.com
The DMSC node does'nt require any of "#address-cells", "#size-cells"
or "ranges" property as the child nodes are representations of SoC's
system controller itself, so align it with the bindings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-4-nm@ti.com
We currently use clocks as the node name for the node representing
TI-SCI clock nodes. This is better renamed to being clock-controller
as that is a better representative of the system controller function
as a clock controller for the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210510145033.7426-2-nm@ti.com
Traffic through main NAVSS interconnect is coherent wrt ARM caches on
J7200 SoC. Add missing dma-coherent property to main_navss node.
Also add dma-ranges to be consistent with mcu_navss node
and with AM65/J721e main_navss and mcu_navss nodes.
Fixes: d361ed8845 ("arm64: dts: ti: Add support for J7200 SoC")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210510180601.19458-1-vigneshr@ti.com
AM654 EVM boards are not shipped with OV5640 sensor module, it is a
separate purchase. OV5640 module is also just one of the possible
sensors or capture boards you can connect.
However, for some reason, OV5640 has been added to the board dts file,
making it cumbersome to use other sensors.
Remove the OV5640 from the dts file so that it is easy to use other
sensors via DT overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210423083120.73476-1-tomi.valkeinen@ideasonboard.com
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: syscon@ff100000:
grf-gpio: {'compatible': ['rockchip,rk3328-grf-gpio'],
'gpio-controller': True, '#gpio-cells': [[2]], 'phandle': [[68]]} is not
of type 'array'
Due to the regex "(?<!,nr)-gpios?$" anything that ends on
'-gpio', '-gpios' gives a match.
Rename 'grf-gpio' nodename to generic 'gpio'
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/gpio/gpio-consumer.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210512122346.9463-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is enough to make the SATA controller visible:
# lspci
00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd RK3399 PCI Express Root Port
01:00.0 SATA controller: JMicron Technology Corp. JMB58x AHCI SATA controller
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210510090932.970447-1-uwe@kleine-koenig.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On the helios64 board the two connectors P6 and P7 are supposed to
power two fans. Add the corresponding pwm-fan devices.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210510090607.970145-1-uwe@kleine-koenig.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long
dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fennel is known as Lenovo IdeaPad Flex 3 Chromebook.
Fennel14 is known as Lenovo IdeaPad 3 Chromebook.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210421090601.730744-11-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kenzo is known as Acer Chromebook 311.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-10-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Burnet is known as HP Chromebook x360 11MK G3 EE
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-9-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Willow is known as Acer Chromebook 311 (C722/C722T)
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-8-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Kappa is known as HP Chromebook 11a
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210421090601.730744-7-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add larb nodes for MT8167:
* larb0 is used for display (dsi and hdmi)
* larb1 is used for camera (csi)
* larb2 is used for the video hardware decoder
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Link: https://lore.kernel.org/r/20210406113631.2675029-1-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are two separate hardware encoder blocks inside MT8173.
Split the current mtk-vcodec-enc node to match the hardware architecture.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Link: https://lore.kernel.org/r/20210325122625.15100-2-irui.wang@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The PinePhone has a Bluetooth chip with its PCM interface connected to
AIF3. Add the DAI link so headeset audio can be routed in hardware.
Even though the link is 16 bit PCM, configuring the link a 32-bit slot
is required for compatibility with AIF2, which also uses a 32-bit slot,
and which shares clock dividers with AIF3. Using equal clock frequencies
allows the modem and headset to be used at the same time.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-7-samuel@sholland.org
simple-audio-card supports either a single DAI link at the top level, or
subnodes with one or more DAI links. To use the secondary AIFs on the
codec, we need to add additional DAI links to the same sound card, so we
need to use the other binding.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-6-samuel@sholland.org
Now that the sun8i-codec driver supports AIF2 and AIF3, boards can use
them in DAI links. Add the necessary pinmux nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-5-samuel@sholland.org
Increase #sound-dai-cells on the digital codec to allow using the other
DAIs provided by the codec for AIF2 and AIF3.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210430035859.3487-4-samuel@sholland.org
For a CPU to enter an idle state, some timer must be available to
trigger an IRQ and wake it back up. The local ARM architectural timer is
not sufficient, because that timer stops when the CPU is powered down.
The ARM architectural timer from some other CPU can be used, but doing
so prevents that other CPU from entering an idle state. For all CPUs to
power down at the same time, Linux needs a timer which is not tied to
any CPU.
Hook up the "sun4i" timer so it can be used for this purpose. It runs at
24 MHz, which balances resolution and power consumption.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210322044707.19479-5-samuel@sholland.org
Nodes should be sorted by unit address. Move the watchdog node to the
correct place, so it will be next to the timer node when that is added.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210322044707.19479-4-samuel@sholland.org
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
optee node was disabled by default, enabling it for ls1028a-rdb.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sahil Malhotra <sahil.malhotra@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx8mp-evk uses an PCA9450C as PMIC that supplies various
regulators.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #power-domain-cells to power domain nodes, because they
are required by power-domain.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-9-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-8-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-7-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The max link speed supported by the rk3399 is already set in the
rk3399.dtsi file so don't set unsupported link speeds in device
specific DTs. This is the same fix as 642fb27.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210413141709.845592-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Turns out the fephy pins are already claimed in the phy node, which is
rightfully where they should be claimed.
Drop the pinctrl properties from the gmac2phy node for the ROCK Pi E.
Fixes: b918e81f21 ("arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210426095916.14574-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
However "sys" is not a valid function, and it is always on.
Let's keep existing functions.
Fixes: db792e9adb ("rockchip: rk3399: Add support for FriendlyARM NanoPi R4S")
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20210426114652.29542-1-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R2S has a Realtek RTL8153B USB 3.0 Ethernet chip connected
to the USB 3.0 pins of the RK3328 SoC. Power to the chip is controlled
by a GPIO line toggled transistor switch, which is not a full-blown
voltage regulator.
At least in Linux, the USB 3.0 XHCI controller has two ports: the first
port is for legacy USB 2.0 and slower, while the second port is for USB
3.0. Since the Ethernet chip supports USB 3.0, it should be described
as connected to the second port.
Add the device nodes for the power switch and Ethernet chip, and enable
the USB 3.0 controller. The USB device node follows the standard USB
device binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210504083616.9654-5-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB3 nodes for the Rock Pi E board.
The VBUS regulator device node was added when the board was first
introduced.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210504083616.9654-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB3 nodes for the ROC-RK3328-CC board.
The separate power regulator is not added as it is controlled by the
same GPIO line as the existing VBUS regulators, so it is already
enabled. Also there is no port representation to tie the regulator to.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210504083616.9654-3-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB3 nodes for the rk3328-based PINE Rock64 board.
The separate power regulator is not added as it is controlled by the
same GPIO line as the existing VBUS regulators, so it is already
enabled. Also there is no port representation to tie the regulator to.
[wens@csie.org: Rebased onto v5.12]
Signed-off-by: Cameron Nemo <cnemo@tutanota.com>
[wens@csie.org: Rewrote commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210504083616.9654-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This set of changes adds support for the PWM controller found on Toshiba
Visconti SoCs and converts a couple of drivers to the atomic API.
There's also a bunch of cleanups and minor fixes across the board.
-----BEGIN PGP SIGNATURE-----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=d0HN
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This adds support for the PWM controller found on Toshiba Visconti
SoCs and converts a couple of drivers to the atomic API.
There's also a bunch of cleanups and minor fixes across the board"
* tag 'pwm/for-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (35 commits)
pwm: Reword docs about pwm_apply_state()
pwm: atmel: Improve duty cycle calculation in .apply()
pwm: atmel: Fix duty cycle calculation in .get_state()
pwm: visconti: Add Toshiba Visconti SoC PWM support
dt-bindings: pwm: Add bindings for Toshiba Visconti PWM Controller
arm64: dts: rockchip: Remove clock-names from PWM nodes
ARM: dts: rockchip: Remove clock-names from PWM nodes
dt-bindings: pwm: rockchip: Add more compatible strings
dt-bindings: pwm: Convert pwm-rockchip.txt to YAML
pwm: mediatek: Remove unused function
pwm: pca9685: Improve runtime PM behavior
pwm: pca9685: Support hardware readout
pwm: pca9685: Switch to atomic API
pwm: lpss: Don't modify HW state in .remove callback
pwm: sti: Free resources only after pwmchip_remove()
pwm: sti: Don't modify HW state in .remove callback
pwm: lpc3200: Don't modify HW state in .remove callback
pwm: lpc18xx-sct: Free resources only after pwmchip_remove()
pwm: bcm-kona: Don't modify HW state in .remove callback
pwm: bcm2835: Free resources only after pwmchip_remove()
...
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
The port@0 is a mandatory port, add or move the declaration to the CSI-2
nodes top declared in dtsi files instead of depending on dts files
adding them when describing the external connection.
This fixes validation warnings for DTB outputs that do not connect all
CSI-2 receivers to transmitters and thus declaring all port@0 nodes in
dts files.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210421150221.3202955-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix the DTS schema by explicitly stating that the input is port@0. This
fixes a schema validation error but has no runtime effect as the default
port number is 0 if not specified.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210421150221.3202955-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rockchip DWMAC glue driver uses the phy node (phy-handle)
reset specifier, and not a "mac-phy" reset specifier.
Remove it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the merge commit
and on the AsahiLinux wiki.
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pBZy
-----END PGP SIGNATURE-----
Merge tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Apple M1 platform support from Arnd Bergmann:
"The Apple M1 is the processor used it all current generation Apple
Macintosh computers. Support for this platform so far is rudimentary,
but it boots and can use framebuffer and serial console over a special
USB cable.
Support for several essential on-chip devices (USB, PCIe, IOMMU, NVMe)
is work in progress but was not ready in time.
A very detailed description of what works is in the commit message of
commit 1bb2fd3880 ("Merge tag 'm1-soc-bringup-v5' [..]") and on the
AsahiLinux wiki"
Link: https://lore.kernel.org/linux-arm-kernel/bdb18e9f-fcd7-1e31-2224-19c0e5090706@marcan.st/
* tag 'arm-apple-m1-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
asm-generic/io.h: Unbork ioremap_np() declaration
arm64: apple: Add initial Apple Mac mini (M1, 2020) devicetree
dt-bindings: display: Add apple,simple-framebuffer
arm64: Kconfig: Introduce CONFIG_ARCH_APPLE
irqchip/apple-aic: Add support for the Apple Interrupt Controller
dt-bindings: interrupt-controller: Add DT bindings for apple-aic
arm64: Move ICH_ sysreg bits from arm-gic-v3.h to sysreg.h
of/address: Add infrastructure to declare MMIO as non-posted
asm-generic/io.h: implement pci_remap_cfgspace using ioremap_np
arm64: Implement ioremap_np() to map MMIO as nGnRnE
docs: driver-api: device-io: Document ioremap() variants & access funcs
docs: driver-api: device-io: Document I/O access functions
asm-generic/io.h: Add a non-posted variant of ioremap()
arm64: arch_timer: Implement support for interrupt-names
dt-bindings: timer: arm,arch_timer: Add interrupt-names support
arm64: cputype: Add CPU implementor & types for the Apple M1 cores
dt-bindings: arm: cpus: Add apple,firestorm & icestorm compatibles
dt-bindings: arm: apple: Add bindings for Apple ARM platforms
dt-bindings: vendor-prefixes: Add apple prefix
There are six new SoCs added this time. Apple M1 and Nuvoton WPCM450
have separate branches because they are new SoC families that require
changes outside of device tree files. The other four are variations of
already supported chips and get merged through this branch:
- STMicroelectronics STM32H750 is one of many variants of STM32
microcontrollers based on the Cortex-M7 core. This is particularly
notable since we rarely add support for new MMU-less chips
these days. In this case, the board that gets added along with
the platform is not a SoC reference platform but the "Art Pi"
(https://art-pi.gitee.io/website/) machine that was originally design
for the RT-Thread RTOS.
- NXP i.MX8QuadMax is a variant of the growing i.MX8 embedded/industrial
SoC family, using two Cortex-A72 and four Cortex-A53 cores. It
gets added along with its reference board, the "NXP i.MX8QuadMax
Multisensory Enablement Kit".
- Qualcomm SC7280 is a Laptop SoC following the SC7180 (Snapdragon 7c)
that is used in some Chromebooks and Windows laptops. Only a reference
board is added for the moment.
- TI AM64x Sita4ra is a new version of the K3 SoC family for industrial
control, motor control, remote IO, IoT gateway etc., similar to the
older AM65x family. Two reference machines are added alongside.
Among the newly added machines, there is a very clear skew towards 64-bit
machines now, with 12 32-bit machines compared to 23 64-bit machines. The
full list sorted by SoC is:
- ASpeed AST2500 BMC: ASRock E3C246D4I Xeon server board
- Allwinner A10: Topwise A721 Tablet
- Amlogic GXL: MeCool KII TV box
- Amlogic GXM: Mecool KIII, Minix Neo U9-H TV boxes
- Broadcom BCM4908: TP-Link Archer C2300 V1 router
- MStar SSD202D: M5Stack UnitV2 camera
- Marvell Armada 38x: ATL-x530 ethernet switch
- Mediatek MT8183 Chromebooks: Lenovo 10e, Acer Spin 311,
Asus Flip CM3, Asus Detachable CM3
- Mediatek MT8516/MT8183: OLogic Pumpkin Board
- NXP i.MX7: reMarkable Tablet
- NXP i.MX8M: Kontron pitx-imx8m, Engicam i.Core MX8M Mini
- Nuvoton NPCM730: Quanta GBS BMC
- Qualcomm X55: Telit FN980 TLB SoM, Thundercomm TurboX T55 SoM
- Qualcomm MSM8998: OnePlus 5/5T phones
- Qualcomm SM8350: Snapdragon 888 Mobile Hardware Development Kit
- Rockchip RK3399: NanoPi R4S board
- STM32MP1: Engicam MicroGEA STM32MP1 MicroDev 2.0 and SOM,
EDIMM2.2 Starter Kit, Carrier, SOM
- TI AM65: Siemens SIMATIC IOT2050 gateway
There is notable work going into extending already supported machines
and SoCs:
- ASpeed AST2500
- Allwinner A23, A83t, A31, A64, H6
- Amlogic G12B
- Broadcom BCM4908
- Marvell Armada 7K/8K/CN91xx
- Mediatek MT6589, MT7622, MT8173, MT8183, MT8195
- NXP i.MX8Q, i.MX8MM, i.MX8MP
- Qualcomm MSM8916, SC7180, SDM845, SDX55, SM8350
- Renesas R-Car M3, V3U
- Rockchip RK3328, RK3399
- STEricsson U8500
- STMicroelectronics STM32MP141
- Samsung Exynos 4412
- TI K3-AM65, K3-J7200
- TI OMAP3
Among the treewide cleanups and bug fixes, two parts stand out:
- There are a number of cleanups for issues pointed out by 'make
dtbs_check' this time, and I expect more to come in the future as we
increasingly check for regressions.
- After a change to the MMC subsystem that can lead to unpredictable
device numbers, several platforms add 'aliases' properties for these
to give each MMC controller a fixed number.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=SpTo
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"There are six new SoCs added this time.
Apple M1 and Nuvoton WPCM450 have separate branches because they are
new SoC families that require changes outside of device tree files.
The other four are variations of already supported chips and get
merged through this branch:
- STMicroelectronics STM32H750 is one of many variants of STM32
microcontrollers based on the Cortex-M7 core.
This is particularly notable since we rarely add support for new
MMU-less chips these days. In this case, the board that gets added
along with the platform is not a SoC reference platform but the
"Art Pi" (https://art-pi.gitee.io/website/) machine that was
originally design for the RT-Thread RTOS.
- NXP i.MX8QuadMax is a variant of the growing i.MX8
embedded/industrial SoC family, using two Cortex-A72 and four
Cortex-A53 cores.
It gets added along with its reference board, the "NXP i.MX8QuadMax
Multisensory Enablement Kit".
- Qualcomm SC7280 is a Laptop SoC following the SC7180 (Snapdragon
7c) that is used in some Chromebooks and Windows laptops.
Only a reference board is added for the moment.
- TI AM64x Sita4ra is a new version of the K3 SoC family for
industrial control, motor control, remote IO, IoT gateway etc.,
similar to the older AM65x family.
Two reference machines are added alongside.
Among the newly added machines, there is a very clear skew towards
64-bit machines now, with 12 32-bit machines compared to 23 64-bit
machines. The full list sorted by SoC is:
- ASpeed AST2500 BMC: ASRock E3C246D4I Xeon server board
- Allwinner A10: Topwise A721 Tablet
- Amlogic GXL: MeCool KII TV box
- Amlogic GXM: Mecool KIII, Minix Neo U9-H TV boxes
- Broadcom BCM4908: TP-Link Archer C2300 V1 router
- MStar SSD202D: M5Stack UnitV2 camera
- Marvell Armada 38x: ATL-x530 ethernet switch
- Mediatek MT8183 Chromebooks: Lenovo 10e, Acer Spin 311, Asus Flip
CM3, Asus Detachable CM3
- Mediatek MT8516/MT8183: OLogic Pumpkin Board
- NXP i.MX7: reMarkable Tablet
- NXP i.MX8M: Kontron pitx-imx8m, Engicam i.Core MX8M Mini
- Nuvoton NPCM730: Quanta GBS BMC
- Qualcomm X55: Telit FN980 TLB SoM, Thundercomm TurboX T55 SoM
- Qualcomm MSM8998: OnePlus 5/5T phones
- Qualcomm SM8350: Snapdragon 888 Mobile Hardware Development Kit
- Rockchip RK3399: NanoPi R4S board
- STM32MP1: Engicam MicroGEA STM32MP1 MicroDev 2.0 and SOM, EDIMM2.2
Starter Kit, Carrier, SOM
- TI AM65: Siemens SIMATIC IOT2050 gateway
There is notable work going into extending already supported machines
and SoCs:
- ASpeed AST2500
- Allwinner A23, A83t, A31, A64, H6
- Amlogic G12B
- Broadcom BCM4908
- Marvell Armada 7K/8K/CN91xx
- Mediatek MT6589, MT7622, MT8173, MT8183, MT8195
- NXP i.MX8Q, i.MX8MM, i.MX8MP
- Qualcomm MSM8916, SC7180, SDM845, SDX55, SM8350
- Renesas R-Car M3, V3U
- Rockchip RK3328, RK3399
- STEricsson U8500
- STMicroelectronics STM32MP141
- Samsung Exynos 4412
- TI K3-AM65, K3-J7200
- TI OMAP3
Among the treewide cleanups and bug fixes, two parts stand out:
- There are a number of cleanups for issues pointed out by 'make
dtbs_check' this time, and I expect more to come in the future as
we increasingly check for regressions.
- After a change to the MMC subsystem that can lead to unpredictable
device numbers, several platforms add 'aliases' properties for
these to give each MMC controller a fixed number"
* tag 'arm-dt-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (516 commits)
dt-bindings: mali-bifrost: add dma-coherent
arm64: dts: amlogic: misc DT schema fixups
arm64: dts: qcom: sc7180: Update iommu property for simultaneous playback
arm64: dts: qcom: sc7180: pompom: Add "dmic_clk_en" + sound model
arm64: dts: qcom: sc7180: coachz: Add "dmic_clk_en"
ARM: dts: mstar: Add a dts for M5Stack UnitV2
dt-bindings: arm: mstar: Add compatible for M5Stack UnitV2
dt-bindings: vendor-prefixes: Add vendor prefix for M5Stack
arm64: dts: mt8183: fix dtbs_check warning
arm64: dts: mt8183-pumpkin: fix dtbs_check warning
ARM: dts: aspeed: tiogapass: add hotplug controller
ARM: dts: aspeed: amd-ethanolx: Enable all used I2C busses
ARM: dts: aspeed: Rainier: Update to pass 2 hardware
ARM: dts: aspeed: Rainier 1S4U: Fix fan nodes
ARM: dts: aspeed: Rainier: Fix humidity sensor bus address
ARM: dts: aspeed: Rainier: Fix PCA9552 on bus 8
ARM: dts: qcom: sdx55: add IPA information
ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55
dt-bindings: arm: qcom: Add binding for Thundercomm T55 kit
ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
Here is the big set of USB and Thunderbolt driver updates for 5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work
with (something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa42A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymMEACgkQBzLb5W/IocS+oq7+D7P3V581sAn1Dcy2Qq
Yz370/X2hrjXAyIm7/Cz
=5dj/
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.13-rc1.
Lots of little things in here, with loads of tiny fixes and cleanups
over these drivers, as well as these "larger" changes:
- thunderbolt updates and new features added
- xhci driver updates and split out of a mediatek-specific xhci
driver from the main xhci module to make it easier to work with
(something that I have been wanting for a while).
- loads of typec feature additions and updates
- dwc2 driver updates
- dwc3 driver updates
- gadget driver fixes and minor updates
- loads of usb-serial cleanups and fixes and updates
- usbip documentation updates and fixes
- lots of other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (371 commits)
usb: Fix up movement of USB core kerneldoc location
usb: dwc3: gadget: Handle DEV_TXF_FLUSH_BYPASS capability
usb: dwc3: Capture new capability register GHWPARAMS9
usb: gadget: prevent a ternary sign expansion bug
usb: dwc3: core: Do core softreset when switch mode
usb: dwc2: Get rid of useless error checks in suspend interrupt
usb: dwc2: Update dwc2_handle_usb_suspend_intr function.
usb: dwc2: Add exit hibernation mode before removing drive
usb: dwc2: Add hibernation exiting flow by system resume
usb: dwc2: Add hibernation entering flow by system suspend
usb: dwc2: Allow exit hibernation in urb enqueue
usb: dwc2: Move exit hibernation to dwc2_port_resume() function
usb: dwc2: Move enter hibernation to dwc2_port_suspend() function
usb: dwc2: Clear GINTSTS_RESTOREDONE bit after restore is generated.
usb: dwc2: Clear fifo_map when resetting core.
usb: dwc2: Allow exiting hibernation from gpwrdn rst detect
usb: dwc2: Fix hibernation between host and device modes.
usb: dwc2: Fix host mode hibernation exit with remote wakeup flow.
usb: dwc2: Reset DEVADDR after exiting gadget hibernation.
usb: dwc2: Update exit hibernation when port reset is asserted
...
These should be the final fixes for v5.12. There is one fix for SD card
detection on one Allwinner board, and a few fixes for the Tegra
platform that I had already queued up for v5.13 due to a communication
problem. This addresses MMC device ordering on multiple machines,
audio support on Jetson AGX Xavier and suspend/resume on Jetson TX2.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=kooC
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These should be the final fixes for v5.12.
There is one fix for SD card detection on one Allwinner board, and a
few fixes for the Tegra platform that I had already queued up for
v5.13 due to a communication problem. This addresses MMC device
ordering on multiple machines, audio support on Jetson AGX Xavier and
suspend/resume on Jetson TX2"
* tag 'arm-fixes-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: allwinner: Revert SD card CD GPIO for Pine64-LTS
arm64: tegra: Move clocks from RT5658 endpoint to device node
arm64: tegra: Fix mmc0 alias for Jetson Xavier NX
arm64: tegra: Set fw_devlink=on for Jetson TX2
arm64: tegra: Add unit-address for ACONNECT on Tegra186
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3368-evb-act8846.dt.yaml:
pwm@ff680030: clock-names: ['pwm'] is too short
Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
arm64: tegra: Device tree fixes for v5.12-rc6
This contains a couple of device tree fixes for the v5.12 release cycle.
These are needed for proper audio support on Jetson AGX Xavier, to boot
the Jetson Xavier NX from an SD card and to be able to suspend/resume
the Jetson TX2.
* tegra/dt64:
arm64: tegra: Move clocks from RT5658 endpoint to device node
arm64: tegra: Fix mmc0 alias for Jetson Xavier NX
arm64: tegra: Set fw_devlink=on for Jetson TX2
arm64: tegra: Add unit-address for ACONNECT on Tegra186
Link: https://lore.kernel.org/linux-arm-kernel/YILD4yyPXuiYbHW1@orome.fritz.box/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take a pass at cleaning up a bunch of warnings
from 'make dtbs_check' that have crept in.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210421204833.18523-1-khilman@baylibre.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYIEprQAKCRDj7w1vZxhR
xSnLAQDInWpOUh1W1ovIe0lHOWYDvByozCh4zQcssKHJhwp25QD/RPTVbwIJI0KV
pOaf8QuqaP74K7KVpbEPBhJG0d6GtwM=
=AaDi
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
One fix for the MMC card detect on the Pine H64 board
* tag 'sunxi-fixes-for-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: Revert SD card CD GPIO for Pine64-LTS
Link: https://lore.kernel.org/r/45fc5e4d-ef48-4729-a869-79a8f288bb83.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 941432d007 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.
After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
virtue of an explicit inverter circuit, as shown in the schematic.
To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.
Fixes: 941432d007 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Reported-by: Daniel Kulesz <kuleszdl@posteo.org>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com
Lad Prabhakar