Now that the platform driver is registered with the cpu_dai's device we
can use the same name for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the platform driver is registered with the cpu_dai's device we
can use the same name for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the platform driver is registered with the cpu_dai's device we
can use the same name for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the platform driver is registered with the cpu_dai's device we
can use the same name/node for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the platform driver is registered with the cpu_dai's device we
can use the same node for it instead of the hardwired name.
We can also remove the cpu_dai_name and platform_name from the dai_link
struct since we only support DT boot on OMAP4/5
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the same device for the platform driver when registering as the dai
driver. This will enable us to clean up some DT booted cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the same device for the platform driver when registering as the dai
driver. This will enable us to clean up some DT booted cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Assign the dai dma data at dai driver probe time, not in startup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the same device for the platform driver when registering as the dai
driver. This will enable us to clean up some DT booted cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Assign the dai dma data at dai driver probe time, not in startup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the same device for the platform driver when registering as the dai
driver. This will enable us to clean up some DT booted cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Assign the dai dma data at dai driver probe time, not in startup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the new calls it is going to be possible to bind the platform driver
to a dai device which makes it easier for us in a long run to handle DT
boots, and opens the possibility to move machine driver to generic simple
card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes.
This on one hand makes the code a bit shorter and cleaner and on the other
hand the board level DAPM elements get registered in the card's DAPM context
rather than in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Machine level DAPM widgets and routes should be registered in the card's DAPM
context, rather than in the CODEC's context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_mutex_unlock() wants a pointer to the DAPM context, not the CODEC.
Fixes: 03510ca07 ("ASoC: ams-delta: Update locking around use of DAPM pin API")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since 3.14-rc1 only DT boot has been supported on N810, so this
file fails to init. Make a minimal fix to retain functionality.
This file should be properly converted to DT in longer term.
There seems to be still other unresolved issues with N810 audio support,
but this patch is needed at minimum as otherwise the machine driver
probing would completely fail.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pin updates in this driver look like they are intended to be done
atomically, update to do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pin updates in this driver look like they are intended to be done
atomically, update to do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pin updates in this driver look like they are intended to be done
atomically, update to do so. It looks like these were originally locked
with the CODEC mutex and not updated since the patch "ASoC: dapm: Use
DAPM mutex for DAPM ops instead of codec mutex", so remove the original
CODEC mutex locking as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The name "max" in struct soc_enum is rather confusing since it
actually takes the number of items. With "max", one might try to
assign (nitems - 1) value.
Rename the field to a more appropriate one, "items", which is also
used in struct snd_ctl_elem_info, too.
This patch also rewrites some code like "if (x > e->nitems - 1)" with
"if (x >= e->nitems)". Not only the latter improves the readability,
it also fixes a potential bug when e->items is zero.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the GPIO jacks are only supported if gpiolib is built and fail to
compile otherwise add a build depedency. This is unlikely to have any
practical impact outside of coverage testing.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
N810 audio driver has stopped working at some point. Probably when
OMAP2 was converted to common clock framework since now call to clk_enable
dumps the stack trace in drivers/clk/clk.c: __clk_enable() due
clk->prepare_count is zero.
Fix this by converting clk_enable/_disable calls to those that take care
of clock prepare/unprepare.
I'm not queueing this to linux-stable since OMAP2 common clock framework
conversion in commit ed1ebc4948 ("ARM: OMAP2: clock: Convert to common clk")
happened before N810 was really usable in mainline and user base for N810 is
anyway small. Potential linux-stable candidates are only those after
commit 3d3a6d18ab ("watchdog: introduce retu_wdt driver").
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Use WARN_ON() and handle the error cases accordingly.
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This code sequence is unsafe in modules:
static u64 mask = DMA_BIT_MASK(something);
...
if (!dev->dma_mask)
dev->dma_mask = &mask;
as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses. Moreover, they
all follow this with:
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = mask;
where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.
Fix these issues by using the new dma_coerce_coherent_and_mask()
function.
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b0e0a4d ("ASoC: omap: Enable COMPILE_TEST build for DT platforms")
added two incorrect CONFIG_ARCH_ARM dependencies making impossible to select
audio support for Nokia RX-51. Fix this by using correct CONFIG_ARM.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_snd_soc_register_component makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
In the case of omap-dmic.c, the error-handling code of
devm_ioremap_resource is also corrected to include releasing the clock.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Peter Ujfalusi