dev_set_drvdata can no longer fail, so it could return void.
All callers have hopefully been updated to no longer check for the
return value.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Analog Devices ADAU1381 and ADAU1781 audio
CODECs. The device is a low-power, 24-bit stereo audio CODEC with multiple
analog inputs and outputs, two digital microphone inputs and an I2S interface.
The device can be controlled either using I2C or SPI. The main difference
between the two variants is that the ADAU1781 has a freely programmable SigmaDSP
processor, while the ADAU1381 has a fixed function wind noise reduction filter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1361 and ADAU1761 CODECs.
The device is a a low-power, 24-bit stereo audio CODEC with multiple analog
input and outputs, one digital microphone input and an I2S interface. The device
can be controlled either via I2C or SPI. The main difference between the two
variants is that the ADAU1761 has a built-in SigmaDSP, while the ADAU1361 has
not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1X61 and ADAU1X81 are very similar in the digital domain, but are quite
different in the analog domain. This patch adds support for the common parts of
the ADAU1X61 and ADAU1X81 CODECs.
The patch also restores some of the alphabetical order in the Makfile and
Kconfig.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Having to allocate memory as part of dev_set_drvdata() is a problem
because that memory may never get freed if the device itself is not
created. So move driver_data back to struct device.
This is a partial revert of commit b4028437.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper function to check a device's header type for PCI bridge or
CardBus bridge.
Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Drivers currently have to figure this out on their own, and they
are missing information to do it properly. The ones that did
attempt to do it, do it wrong.
So just pass in the suggested node directly to the alloc
function.
Signed-off-by: Jens Axboe <axboe@fb.com>
Notify a PCI device driver when its device's access is about to be disabled
for an impending reset attempt, then after the attempt completes and device
access is restored. The notification is via the pci_error_handlers
interface.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* dma-api:
iommu/exynos: Remove unnecessary "&" from function pointers
DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
DMA-API: Capitalize "CPU" consistently
sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
DMA-API: Clarify physical/bus address distinction
* pci/virtualization:
PCI: Mark RTL8110SC INTx masking as broken
* pci/msi:
PCI/MSI: Remove pci_enable_msi_block()
* pci/misc:
PCI: Remove pcibios_add_platform_entries()
s390/pci: use pdev->dev.groups for attribute creation
PCI: Move Open Firmware devspec attribute to PCI common code
* pci/resource:
PCI: Add resource allocation comments
PCI: Simplify __pci_assign_resource() coding style
PCI: Change pbus_size_mem() return values to be more conventional
PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
PCI: Support BAR sizes up to 8GB
resources: Clarify sanity check message
PCI: Don't add disabled subtractive decode bus resources
PCI: Don't print anything while decoding is disabled
PCI: Don't set BAR to zero if dma_addr_t is too small
PCI: Don't convert BAR address to resource if dma_addr_t is too small
PCI: Reject BAR above 4GB if dma_addr_t is too small
PCI: Fail safely if we can't handle BARs larger than 4GB
x86/gart: Tidy messages and add bridge device info
x86/gart: Replace printk() with pr_info()
x86/PCI: Move pcibios_assign_resources() annotation to definition
x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
x86/PCI: Fix Broadcom CNB20LE unintended sign extension
Some firmware drivers, ie acpi-video want to get themselves out of the
way (in some cases) when their also is a raw backlight device available.
Due to module loading ordering being unknown, acpi-video cannot be certain
that the backlight_device_registered(BACKLIGHT_RAW) it does for this is
the final verdict wrt there being a BACKLIGHT_RAW device.
By adding notification acpi-video can listen for backlight devices showing
up after it has loaded, and unregister its backlight device if desired.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
information available within the IP instead
of reading it from platform data or DT. Some
other useful clean-ups are included too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=AWLc
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
Merge "DaVinci EDMA clean-up for v3.16" from Sekhar Nori:
This series makes edma use configuration information available within
the IP instead of reading it from platform data or DT. Some other useful
clean-ups are included too.
* tag 'davinci-for-v3.16/edma' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (34 commits)
ARM: edma: Remove redundant/unused parameters from edma_soc_info
ARM: davinci: Remove redundant/unused parameters for edma
ARM: dts: am4372: Remove obsolete properties from edma node
ARM: dts: am33xx: Remove obsolete properties from edma node
dt/bindings: ti,edma: Remove redundant properties from documentation
ARM: edma: Get IP configuration from HW (number of channels, tc, etc)
ARM: edma: Save number of regions from pdata to struct edma
ARM: edma: Remove num_cc member from struct edma
ARM: edma: Remove queue_tc_mapping data from edma_soc_info
ARM: davinci: Remove eDMA3 queue_tc_mapping data from edma_soc_info
ARM: edma: Do not change TC -> Queue mapping, leave it to default.
ARM: edma: Take the number of tc from edma_soc_info (pdata)
ARM: edma: No need to clean the pdata in edma_of_parse_dt()
ARM: edma: Clean up and simplify the code around irq request
dmaengine: edma: update DMA memcpy to use new param element
dmaengine: edma: Document variables used for residue accounting
dmaengine: edma: Provide granular accounting
dmaengine: edma: Make reading the position of active channels work
dmaengine: edma: Store transfer data in edma_desc and edma_pset
dmaengine: edma: Create private pset struct
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge a fix from Philipp Zabel:
This patch fixes an erroneous revert that slipped in with commit
b424080a9e reset: Add optional resets and
stubs.
* 'reset/fixes' of git://git.pengutronix.de/git/pza/linux:
reset: Add of_reset_control_get to reset.h
Signed-off-by: Olof Johansson <olof@lixom.net>
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 1a699476e2 ("ACPI / hotplug / PCI: Hotplug notifications
from acpi_bus_notify()") added debug messages for a few common
events. These debug messages are unconditionally enabled if
CONFIG_DYNAMIC_DEBUG is defined, contrary to the documented
meaning, making the ACPI system spew lots of unwanted noise on
any kernel with dynamic debugging.
The bug was introduced by commit fbfddae696 ("ACPI: Add
acpi_handle_<level>() interfaces"), which added the
CONFIG_DYNAMIC_DEBUG dependency without respecting its meaning.
Fix by adding real support for dynamic_debug.
Fixes: fbfddae696 ("ACPI: Add acpi_handle_<level>() interfaces")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In post commit, a quirk of this firmware about transactions is reported.
This commit apply a workaround for this quirk.
They often fail transactions due to gap_count mismatch. This state is changed
by generating bus reset.
The fw_schedule_bus_reset() is an exported symbol in firewire-core. But there
are no header for public. This commit moves its prototype from
drivers/firewire/core.h to include/linux/firewire.h.
This mismatch still affects bus management before generating this bus reset.
It still takes a time to call driver's probe() because transactions are still
often failed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds Qualcomm amba vendor Id to the list. This ID is used in mmci driver. The ID selected in same lines like 0x41 is "A" for ARM, 0x51 is "Q" for Qualcomm.
As there are no physical register on Qcom SOC for amba vendor id, this is a fake ID assigned based on "Q" prefix from Qualcomm.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch add resource-managed function for devfreq opp as following
functions. The devm_devfreq_register_opp_notifier() manages automatically
the registration of devfreq opp using device resource management.
- devm_devfreq_register_opp_notifier
- devm_devfreq_unregister_opp_notifier()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add resource-managed function for devfreq device as following
functions. The devm_devfreq_add_device() manages automatically the memory
of devfreq device using device resource management.
- devm_devfreq_add_device()
- devm_devfreq_remove_device()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
1/ async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
2/ mv_xor: register write ordering fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XFIL
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
"Two fixes for -stable:
- async_mult() sometimes maps less buffers than initially requested.
We end up freeing dmaengine_unmap_data on an invalid pool.
- mv_xor: register write ordering fix"
* tag 'dmaengine-fixes-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
dmaengine: fix dmaengine_unmap failure
dma: mv_xor: Flush descriptors before activating a channel
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
Export the blk-mq in-flight tag iterator for driver consumption.
This is particularly useful in exception paths or SRSI where
in-flight IOs need to be cancelled and/or reissued. The NVMe driver
conversion will use this.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
devm_get_free_pages() and devm_free_pages() are the managed counterparts
for __get_free_pages() and free_pages().
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull scheduler fixes from Ingo Molnar:
"The biggest commit is an irqtime accounting loop latency fix, the rest
are misc fixes all over the place: deadline scheduling, docs, numa,
balancer and a bad to-idle latency fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Initialize newidle balance stats in sd_numa_init()
sched: Fix updating rq->max_idle_balance_cost and rq->next_balance in idle_balance()
sched: Skip double execution of pick_next_task_fair()
sched: Use CPUPRI_NR_PRIORITIES instead of MAX_RT_PRIO in cpupri check
sched/deadline: Fix memory leak
sched/deadline: Fix sched_yield() behavior
sched: Sanitize irq accounting madness
sched/docbook: Fix 'make htmldocs' warnings caused by missing description
Pull perf fixes from Ingo Molnar:
"The biggest changes are fixes for races that kept triggering Trinity
crashes, plus liblockdep build fixes and smaller misc fixes.
The liblockdep bits in perf/urgent are a pull mistake - they should
have been in locking/urgent - but by the time I noticed other commits
were added and testing was done :-/ Sorry about that"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race between ring_buffer_detach() and ring_buffer_attach()
perf: Prevent false warning in perf_swevent_add
perf: Limit perf_event_attr::sample_period to 63 bits
tools/liblockdep: Remove all build files when doing make clean
tools/liblockdep: Build liblockdep from tools/Makefile
perf/x86/intel: Fix Silvermont's event constraints
perf: Fix perf_event_init_context()
perf: Fix race in removing an event
In commit ad86622b47 ("wait: swap EXIT_ZOMBIE and EXIT_DEAD to hide
EXIT_TRACE from user-space") the order of task state definitions were
changed: EXIT_DEAD and EXIT_ZOMBIE were swapped. Though the charterers
for the states in TASK_STATE_TO_CHAR_STR string were not updated. This
patch synchronizes the string to the order of definitions.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 9ec36cafe4
"of/irq: do irq resolution in platform_get_irq" from Rob Herring -
moves resolving of the interrupt resources in platform_get_irq().
But this solution isn't complete because platform_get_irq_byname()
need to be modified the same way.
Hence, fix it by adding interrupt resolution code at the
platform_get_irq_byname() function too.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <robh@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
The strchrnul() variant helpfully returns a the end of the string
instead of a NULL if the requested character is not found. This can
simplify string parsing code since it doesn't need to expicitly check
for a NULL return. If a valid string pointer is passed in, then a valid
null terminated string will always come back out.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Remove pcibios_add_platform_entries(). Architecture-specific attributes
can be achieved by setting pdev->dev.groups.
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull RCU updates from Paul E. McKenney:
" 1. Update RCU documentation. These were posted to LKML at
https://lkml.org/lkml/2014/4/28/634.
2. Miscellaneous fixes. These were posted to LKML at
https://lkml.org/lkml/2014/4/28/645.
3. Torture-test changes. These were posted to LKML at
https://lkml.org/lkml/2014/4/28/667.
4. Variable-name renaming cleanup, sent separately due to conflicts.
This was posted to LKML at https://lkml.org/lkml/2014/5/13/854.
5. Patch to suppress RCU stall warnings while sysrq requests are
being processed. This patch is the RCU portions of the patch
that Rik posted to LKML at https://lkml.org/lkml/2014/4/29/457.
The reason for pushing this patch ahead instead of waiting until
3.17 is that the NMI-based stack traces are messing up sysrq
output, and in some cases also messing up the system as well."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the n_cc as well since in this context it has no meaning. We have
separate edma_soc_info struct/eDMA3_CC instance so this member does not
make any sense (and the driver no longer uses it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently, hid-rmi drives every Synaptics product, but the touchscreens
on the Windows tablets should be handled through hid-multitouch.
Instead of providing a long list of PIDs, rely on the scan_report
capability to detect which should go to hid-multitouch, and which
should not go to hid-rmi.
related bug:
https://bugzilla.kernel.org/show_bug.cgi?id=74241https://bugzilla.redhat.com/show_bug.cgi?id=1089583
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bringing in as an external dependency that the renesas/clock-cleanup2 branch
relies on.
* depends/clockevents-cleanups: (52 commits)
clocksource: sh_mtu2: Sort headers alphabetically
clocksource: sh_mtu2: Remove FSF mail address from GPL notice
clocksource: sh_mtu2: Rename clock to "fck" in the non-legacy case
clocksource: sh_mtu2: Add support for multiple channels per device
clocksource: sh_mtu2: Hardcode MTU2 clock event rating to 200
clocksource: sh_mtu2: Set cpumask to cpu_possible_mask
clocksource: sh_mtu2: Replace hardcoded register values with macros
clocksource: sh_mtu2: Allocate channels dynamically
clocksource: sh_mtu2: Replace kmalloc + memset with kzalloc
clocksource: sh_mtu2: Add index to struct sh_mtu2_channel
clocksource: sh_mtu2: Add memory base to sh_mtu2_channel structure
clocksource: sh_mtu2: Constify name argument to sh_mtu2_register()
clocksource: sh_mtu2: Split channel setup to separate function
clocksource: sh_mtu2: Rename struct sh_mtu2_priv to sh_mtu2_device
clocksource: sh_mtu2: Split channel fields from sh_mtu2_priv
clocksource: sh_mtu2: Turn sh_mtu2_priv fields into local variables
clocksource: sh_mtu2: Use request_irq() instead of setup_irq()
clocksource: sh_tmu: Sort headers alphabetically
clocksource: sh_tmu: Remove FSF mail address from GPL notice
clocksource: sh_tmu: Rename clock to "fck" in the non-legacy case
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The count which is used to get_unmap_data maybe not the same as the
count computed in dmaengine_unmap which causes to free data in a
wrong pool.
This patch fixes this issue by keeping the map count with unmap_data
structure and use this count to get the pool.
Cc: <stable@vger.kernel.org>
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Prepare this for the next patch which adds more smarts in the
plugging logic, so that we can save some memory.
Signed-off-by: Jens Axboe <axboe@fb.com>
Here are two driver core (well, sysfs) fixes for 3.15-rc6 that resolve
some reported issues and a regression from 3.13.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEUEABECAAYFAlN8LzgACgkQMUfUDdst+ynJnQCeKQt7KdEBlHAKI5/iP2IQVNNx
KG8AmMepPCjpp9/MbrFQnx3miGgNEug=
=813a
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two driver core (well, sysfs) fixes for 3.15-rc6 that resolve
some reported issues and a regression from 3.13"
* tag 'driver-core-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: make sure read buffer is zeroed
kernfs, sysfs, cgroup: restrict extra perm check on open to sysfs
BCM590xx utilizes a secondary I2C slave address to access additional
register space. Add support for the secondary address space by
instantiating a dummy I2C device with the appropriate secondary
I2C slave address. Also expose a secondary regmap register space so
that MFD drivers can access this secondary i2c slave address space.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull more cgroup fixes from Tejun Heo:
"Three more patches to fix cgroup_freezer breakage due to the recent
cgroup internal locking changes - an operation cgroup_freezer was
using now requires sleepable context and cgroup_freezer was invoking
that while holding a spin lock. cgroup_freezer was using an overly
elaborate hierarchical locking scheme.
While it's possible to convert the hierarchical spinlocks directly to
mutexes, this patch simplifies the overall locking so that it uses a
global mutex. This has the added benefit of avoiding iterating
potentially huge number of tasks under a spinlock. While the patch is
on the larger side in the devel cycle, the changes made are mostly
straight-forward and the locking logic is a lot simpler afterwards"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix rcu_read_lock() leak in update_if_frozen()
cgroup_freezer: replace freezer->lock with freezer_mutex
cgroup: introduce task_css_is_root()
of_get_named_gpiod_flags() is visible and directly usable by GPIO
consumers, but it really should not as the gpiod interface relies
on the simpler gpiod_get() to provide properly-configured GPIOs.
of_get_named_gpiod_flags() is just used internally by gpiolib to
implement gpiod_get(), and by the old of_get_named_gpio_flags()
function, therefore it makes sense to make it gpiolib-private.
As a side-effect, the unused (and unneeded) of_get_gpiod_flags()
inline function is also removed, and of_get_named_gpio_flags() is moved
from a static inline function to a regular one in gpiolib-of.c
This results in all references to gpiod_* functions in of_gpio.h being
gone, which is the way it should be since this file is part of the old
integer GPIO interface.
Changes since v1:
- Fixed compilation error when CONFIG_OF_GPIO is not defined
- Fixed warning due to of_gpio_flags enum not being declared
in private gpiolib.h header
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch contains bug fixes important to get into v3.15. There is a
fix for modifying properties seen during early boot, a fix for an
incorrect prototype when CONFIG_OF=n, and a couple of corrections to
device tree memory nodes on a few platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kY49
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree fixes from Grant Likely:
"Drivercore bugfixes for v3.15
This branch contains bug fixes important to get into v3.15. There is
a fix for modifying properties seen during early boot, a fix for an
incorrect prototype when CONFIG_OF=n, and a couple of corrections to
device tree memory nodes on a few platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
mips: dts: Fix missing device_type="memory" property in memory nodes
arm: dts: Fix missing device_type="memory" for ste-ccu8540
of: fix CONFIG_OF=n prototype of of_node_full_name()
of: make of_update_property() usable earlier in the boot process
It is not possible to reference the omap_dma_filter_fn filter
function from a built-in driver if the dmaengine driver itself
is a loadable module, which is a valid configuration otherwise.
This provides only the dummy alternative if the function
is referenced by a built-in driver to allow a successful
build. The filter function is only required by ATAGS based
platforms, which will continue to be broken after this change
for the bogus configuration. When booting from DT, with the
dma channels correctly listed there, it will work fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_declare_coherent_memory() takes two addresses for a region of memory: a
"bus_addr" and a "device_addr". I think the intent is that "bus_addr" is
the physical address a *CPU* would use to access the region, and
"device_addr" is the bus address the *device* would use to address the
region.
Rename "bus_addr" to "phys_addr" and change its type to phys_addr_t.
Most callers already supply a phys_addr_t for this argument. The others
supply a 32-bit integer (a constant, unsigned int, or __u32) and need no
change.
Use "unsigned long", not phys_addr_t, to hold PFNs.
No functional change (this could theoretically fix a truncation in a config
with 32-bit dma_addr_t and 64-bit phys_addr_t, but I don't think there are
any such cases involving this code).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: James Bottomley <jbottomley@Parallels.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
The DMA-API documentation sometimes refers to "physical addresses" when it
really means "bus addresses." Sometimes these are identical, but they may
be different if the bridge leading to the bus performs address translation.
Update the documentation to use "bus address" when appropriate.
Also, consistently capitalize "DMA", use parens with function names, use
dev_printk() in examples, and reword a few sections for clarity.
No functional change; documentation changes only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Bottomley <jbottomley@Parallels.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Copy u-boot's FDT address translation code from common/fdt_support. This
code was originally based on the kernel's unflattened DT address parsing
code.
This commit can be reverted once relicensing of this code to GPLv2/BSD
is done and it is added to libfdt.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
This adds the infrastructure to generic earlycon for earlycon setup
using DT. The actual setup is not enabled until a following commit to
add the FDT parsing.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
We now have several OF match tables using linker sections that are
nearly the same definition. The only variation is the callback function
prototype. Create a common define for creating linker section OF match
table entries which each table declaration can use.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
All the parameters for RESERVEDMEM_OF_DECLARE function callbacks are
members of struct reserved_mem, so just pass the struct ptr to callback
functions so the function callback is more in line with other OF match
table callbacks.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
For request_fn based devices, the block layer exports a 'nr_requests'
file through sysfs to allow adjusting of queue depth on the fly.
Currently this returns -EINVAL for blk-mq, since it's not wired up.
Wire this up for blk-mq, so that it now also always dynamic
adjustments of the allowed queue depth for any given block device
managed by blk-mq.
Signed-off-by: Jens Axboe <axboe@fb.com>
The new function vlan_get_encap_level() uses vlan_dev_priv()
which is only conditionally avaialble when VLAN support is
enabled. Make vlan_get_encap_level() conditionally available
as well.
Fixes: 44a4085538 ("bonding: Fix stacked device detection in arp monitoring")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fractional divider clocks are fairly common. This adds basic
type for them.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No reason for excluding the remaining ones.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[rjw: Rebased and exported the new acpi_subsys_complete() too.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add the physmem list to the memblock structure. This list only exists
if HAVE_MEMBLOCK_PHYS_MAP is selected and contains the unmodified
list of physically available memory. It differs from the memblock
memory list as it always contains all memory ranges even if the
memory has been restricted, e.g. by use of the mem= kernel parameter.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Refactor the memblock code and extend the memblock API to make it
more flexible. With the extended API it is simple to define and
work with additional memory lists.
The static functions memblock_add_region and __memblock_remove are
renamed to memblock_add_range and meblock_remove_range and added to
the memblock API.
The __next_free_mem_range and __next_free_mem_range_rev functions
are replaced with calls to the more generic list walkers
__next_mem_range and __next_mem_range_rev.
To walk an arbitrary memory list two new macros for_each_mem_range
and for_each_mem_range_rev are added. These new macros are used
to define for_each_free_mem_range and for_each_free_mem_range_reverse.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull irq fixes from Thomas Gleixner:
"Two small updates from the irq departement:
- Provide missing inline stub for a SMP only function
- Add sub-maintainer for the drivers/irqchip/ part of the irq
subsystem. YAY!"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Add co-maintainer for drivers/irqchip
genirq: Provide irq_force_affinity fallback for non-SMP
- Armada 375/38x coherency support
- Armada 375/38x SMP support
- mvebu PMSU and CPU reset support
- Armada 370/XP cpuidle support
- kirkwood remove platform init of audio device
- small fixes and cleanup for new SoC (375/38x)
Note:
- due to complex deps, cpuidle changes Acked by appropriate maintainer for
going though arm-soc tree.
Depends:
- tags/irqchip-mvebu-3.16 in the mvebu/irqchip branch (tglx already pulled) for:
d7df84b3ce irqchip: irq-armada-370-xp: Use cpu notifier to initialize secondary CPUs
ef37d337e1 irqchip: irq-armada-370-xp: Do the set_smp_cross_call() in the driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=wNp0
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-3.16' of git://git.infradead.org/linux-mvebu into next/soc
Merge "ARM: mvebu: SoC changes for v3.16" from Jason Cooper:
mvebu SoC changes for v3.16
- Armada 375/38x coherency support
- Armada 375/38x SMP support
- mvebu PMSU and CPU reset support
- Armada 370/XP cpuidle support
- kirkwood remove platform init of audio device
- small fixes and cleanup for new SoC (375/38x)
Note:
- due to complex deps, cpuidle changes Acked by appropriate maintainer for
going though arm-soc tree.
* tag 'mvebu-soc-3.16' of git://git.infradead.org/linux-mvebu: (46 commits)
ARM: mvebu: Fix pmsu compilation when ARMv6 is selected
ARM: mvebu: conditionalize Armada 375 coherency workaround
ARM: mvebu: conditionalize Armada 375 SMP workaround
ARM: mvebu: add Armada 375 A0 revision definition
ARM: mvebu: initialize mvebu-soc-id earlier
ARM: mvebu: fix thermal quirk SoC revision check
ARM: Kirkwood: t5325: Remove platform device to instantiate audio
ARM: Kirkwood: Remove platform driver for codec
ARM: mvebu: Add thermal quirk for the Armada 375 DB board
ARM: mvebu: Select HAVE_ARM_TWD only if SMP is enabled
ARM: mvebu: fix the name of the parameter used in mvebu_get_soc_id
ARM: mvebu: remove unnecessary ifdef around l2x0_of_init
ARM: mvebu: register the cpuidle driver for the Armada XP SoCs
cpuidle: mvebu: Add initial CPU idle support for Armada 370/XP SoC
ARM: mvebu: Register notifier callback for the cpuidle transition
ARM: mvebu: refine which files are build in mach-mvebu
ARM: mvebu: Add the PMSU related part of the cpu idle functions
ARM: mvebu: Allow to power down L2 cache controller in idle mode
ARM: mvebu: Low level function to disable HW coherency support
ARM: mvebu: Split low level functions to manipulate HW coherency
...
Signed-off-by: Olof Johansson <olof@lixom.net>
We should be checking for a 64bit platform not 64bit DMA address types in
the case of Goldfish. The Goldfish virtual platform is either 32/32 or
64/64.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bunch of fixes and a new driver for Exynos5 USB 3.0 PHY.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gwmY
-----END PGP SIGNATURE-----
Merge tag 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
for 3.16 merge window
Bunch of fixes and a new driver for Exynos5 USB 3.0 PHY.
This patchset add resource-managed functions to automatically control the memory
and unregistration operation of extcon. Also, This series support new MAX77836
extcon device driver on existing MAX14577 device because existed a little
difference between MAX77836 and MAX14577. Finally, Fix minor issue of extcon
driver.
Detailed description for patchset:
1. Add resource-managed functions
- Add resource-managed functions to automatically free the memory of extcon
structure and to control unregistration behavior as following. This new devm_*
functions applied all of extcon drivers in drivers/extcon/.
: devm_extcon_dev_register/unregister()
: devm_extcon_dev_allocate/free()
: extcon_dev_allocate/free() for devm_extcon_dev_allocate/free()
2. Add new MAX77836 extcon device
- Support MAX77836 device on existing MAX14577 device driver using
different compatible string. This patchset has dependency on MFD/
Regulator/Extcon. So, Lee Jones(MFD Maintainer) created Immutable
branch between MFD and Extcon due for v3.16 merge-window and then
I merged this patchset from MFD git repo[1] to Extcon git repo.
: [1] git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
(branch: ib-mfd-extcon-3.16)
3. Fix minor issue of extcon driver
- extcon-palmas driver
: Fix issue of extcon device name for probe
- extcon-max14577
: Fix probe failure about handling wrong return value.
: Properly Handle return value of regmap_irq_get_virq function.
- extcon-max8997/max77693 driver
: Fix NULL pointer exception on missing pdata
4. Code clean for extcon driver
- extcon-max8997/max77693
: Use power efficient workqueue for delayed cable detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7wRd
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for v3.16
This patchset add resource-managed functions to automatically control the memory
and unregistration operation of extcon. Also, This series support new MAX77836
extcon device driver on existing MAX14577 device because existed a little
difference between MAX77836 and MAX14577. Finally, Fix minor issue of extcon
driver.
Detailed description for patchset:
1. Add resource-managed functions
- Add resource-managed functions to automatically free the memory of extcon
structure and to control unregistration behavior as following. This new devm_*
functions applied all of extcon drivers in drivers/extcon/.
: devm_extcon_dev_register/unregister()
: devm_extcon_dev_allocate/free()
: extcon_dev_allocate/free() for devm_extcon_dev_allocate/free()
2. Add new MAX77836 extcon device
- Support MAX77836 device on existing MAX14577 device driver using
different compatible string. This patchset has dependency on MFD/
Regulator/Extcon. So, Lee Jones(MFD Maintainer) created Immutable
branch between MFD and Extcon due for v3.16 merge-window and then
I merged this patchset from MFD git repo[1] to Extcon git repo.
: [1] git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
(branch: ib-mfd-extcon-3.16)
3. Fix minor issue of extcon driver
- extcon-palmas driver
: Fix issue of extcon device name for probe
- extcon-max14577
: Fix probe failure about handling wrong return value.
: Properly Handle return value of regmap_irq_get_virq function.
- extcon-max8997/max77693 driver
: Fix NULL pointer exception on missing pdata
4. Code clean for extcon driver
- extcon-max8997/max77693
: Use power efficient workqueue for delayed cable detection
Some sysrq handlers can run for a long time, because they dump a lot
of data onto a serial console. Having RCU stall warnings pop up in
the middle of them only makes the problem worse.
This commit provides rcu_sysrq_start() and rcu_sysrq_end() APIs to
temporarily suppress RCU CPU stall warnings while a sysrq request is
handled.
Signed-off-by: Rik van Riel <riel@redhat.com>
[ paulmck: Fix TINY_RCU build error. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Each hardware queue has a bitmap of software queues with pending
requests. When new IO is queued on a software queue, the bit is
set, and when IO is pruned on a hardware queue run, the bit is
cleared. This causes a lot of traffic. Switch this from the regular
BITS_PER_LONG bitmap to a sparser layout, similarly to what was
done for blk-mq tagging.
20% performance increase was observed for single threaded IO, and
about 15% performanc increase on multiple threads driving the
same device.
Signed-off-by: Jens Axboe <axboe@fb.com>
Alexander noticed that we use RCU iteration on rb->event_list but do
not use list_{add,del}_rcu() to add,remove entries to that list, nor
do we observe proper grace periods when re-using the entries.
Merge ring_buffer_detach() into ring_buffer_attach() such that
attaching to the NULL buffer is detaching.
Furthermore, ensure that between any 'detach' and 'attach' of the same
event we observe the required grace period, but only when strictly
required. In effect this means that only ioctl(.request =
PERF_EVENT_IOC_SET_OUTPUT) will wait for a grace period, while the
normal initial attach and final detach will not be delayed.
This patch should, I think, do the right thing under all
circumstances, the 'normal' cases all should never see the extra grace
period, but the two cases:
1) PERF_EVENT_IOC_SET_OUTPUT on an event which already has a
ring_buffer set, will now observe the required grace period between
removing itself from the old and attaching itself to the new buffer.
This case is 'simple' in that both buffers are present in
perf_event_set_output() one could think an unconditional
synchronize_rcu() would be sufficient; however...
2) an event that has a buffer attached, the buffer is destroyed
(munmap) and then the event is attached to a new/different buffer
using PERF_EVENT_IOC_SET_OUTPUT.
This case is more complex because the buffer destruction does:
ring_buffer_attach(.rb = NULL)
followed by the ioctl() doing:
ring_buffer_attach(.rb = foo);
and we still need to observe the grace period between these two
calls due to us reusing the event->rb_entry list_head.
In order to make 2 happen we use Paul's latest cond_synchronize_rcu()
call.
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507123526.GD13658@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prior to commit fbd929f2dc
bonding: support QinQ for bond arp interval
the arp monitoring code allowed for proper detection of devices
stacked on top of vlans. Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device. However, this is not always the
case, as it is possible to extend the stacked configuration.
With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.
For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan
Note: This patch limites the number of stacked VLANs to 2,
just like before. The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic. This is no longer
possible.
Fixes: fbd929f2dc (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dc8eaaa006.
vlan: Fix lockdep warning when vlan dev handle notification
Instead we use the new new API to find the lock subclass of
our vlan device. This way we can support configurations where
vlans are interspersed with other devices:
bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netif_addr_lock_nested assumes that there can be only
a single nesting level between 2 devices. However, if we
have multiple devices of the same type stacked, this fails.
For example:
eth0 <-- vlan0.10 <-- vlan0.10.20
A more complicated configuration may stack more then one type of
device in different order.
Ex:
eth0 <-- vlan0.10 <-- macvlan0 <-- vlan1.10.20 <-- macvlan1
This patch adds an ndo_* function that allows each stackable
device to report its nesting level. If the device doesn't
provide this function default subclass of 1 is used.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.
For example:
eth0 <- vlan0.10 <- macvlan0 <- vlan1.20
The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, some subsystems (e.g. PCI and the ACPI PM domain) have to
resume all runtime-suspended devices during system suspend, mostly
because those devices may need to be reprogrammed due to different
wakeup settings for system sleep and for runtime PM.
For some devices, though, it's OK to remain in runtime suspend
throughout a complete system suspend/resume cycle (if the device was in
runtime suspend at the start of the cycle). We would like to do this
whenever possible, to avoid the overhead of extra power-up and power-down
events.
However, problems may arise because the device's descendants may require
it to be at full power at various points during the cycle. Therefore the
most straightforward way to do this safely is if the device and all its
descendants can remain runtime suspended until the complete stage of
system resume.
To this end, introduce a new device PM flag, power.direct_complete
and modify the PM core to use that flag as follows.
If the ->prepare() callback of a device returns a positive number,
the PM core will regard that as an indication that it may leave the
device runtime-suspended. It will then check if the system power
transition in progress is a suspend (and not hibernation in particular)
and if the device is, indeed, runtime-suspended. In that case, the PM
core will set the device's power.direct_complete flag. Otherwise it
will clear power.direct_complete for the device and it also will later
clear it for the device's parent (if there's one).
Next, the PM core will not invoke the ->suspend() ->suspend_late(),
->suspend_irq(), ->resume_irq(), ->resume_early(), or ->resume()
callbacks for all devices having power.direct_complete set. It
will invoke their ->complete() callbacks, however, and those
callbacks are then responsible for resuming the devices as
appropriate, if necessary. For example, in some cases they may
need to queue up runtime resume requests for the devices using
pm_request_resume().
Changelog partly based on an Alan Stern's description of the idea
(http://marc.info/?l=linux-pm&m=139940466625569&w=2).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This patch adds UPDATE_QP SRIOV wrapper support.
The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today's linux-next kernel started showing build errors for the
use of WARN_ON in linux/gpio/consumer.h:
In file included from drivers/video/backlight/pwm_bl.c:13:0:
include/linux/gpio/consumer.h: In function 'gpiod_put':
include/linux/gpio/consumer.h:81:2: error: implicit declaration of function 'WARN_ON' [-Werror=implicit-function-declaration]
It's not clear why this never happened before, but this patch
fixes it by including the header that contains the defintion
of this macro.
Signed-off-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "freeze" sleep state suffers from the same issue that was
addressed by commit ad07277e82 (ACPI / PM: Hold acpi_scan_lock over
system PM transitions) for ACPI sleep states, that is, things break
if ->remove() is called for devices whose system resume callbacks
haven't been executed yet.
It also can be addressed in the same way, by holding the ACPI scan
lock over the "freeze" sleep state and PM transitions to and from
that state, but ->begin() and ->end() platform operations for the
"freeze" sleep state are needed for this purpose.
This change has been tested on Acer Aspire S5 with Thunderbolt.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds a driver for the SSI McSAAB protocol as used in
the Nokia N900.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Expose method for registering and unregistering HSI clients, so that
client drivers can register other client drivers.
This is useful for HSI drivers, which want to use the functionality
of other HSI drivers. For example the N900 modem driver can load HSI
drivers for mcsaab protocol and speech protocol.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Make HSI channel ids platform data, which can be provided
by platform data.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
This exports a method to unregister all clients from
an hsi port.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
From: Cong Wang <cwang@twopensource.com>
commit 50624c934d (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.
For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last reason for static memory mapping is the HBI (board
identification number) check early in the machine code.
Moving the check to the sysreg driver makes it possible to
completely remove the early mapping and init functions.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
This patch - finally, after over 6 months! :-( - addresses
Samuel's request to split the vexpress-sysreg driver into
smaller portions and define the device in a form of MFD
cells:
* LEDs code has been completely removed and replaced with
"gpio-leds" nodes in the tree (referencing dedicated
GPIO subnodes in sysreg - bindings documentation updated);
this also better fits the reality as some variants of the
motherboard don't have all the LEDs populated
* syscfg bridge code has been extracted into a separate
driver (placed in drivers/misc for no better place)
* all the ID & MISC registers are defined as sysconf
making them available for other drivers should they need
to use them (and also to the user via /sys/kernel/debug/regmap
which can be helpful in platform debugging)
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Define syscon platform data structure that can be used
to define a regmap config name. This is particularly useful
in the regmap debugfs when there is more than one syscon
device registered, to distinguish the register blocks.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
In "Device Tree powered" systems, platform devices are usually massively
populated with of_platform_populate() call, executed at some level of
initcalls, either by generic architecture or by platform-specific code.
There are situations though where certain devices must be created (and
bound with drivers) before all the others. This presents a challenge,
as devices created explicitly would be created again by
of_platform_populate().
This patch tries to solve that issue in a generic way, adding a
"populated" flag for a DT node description. Subsequent
of_platform_populate() will skip such nodes (and its children) in
a similar way to the non-available ones.
This patch also adds of_platform_depopulate() as an operation
complementary to the _populate() one. It removes a platform or an amba
device populated from the Device Tree, together with its all children
(leaving, however, devices without associated of_node untouched)
clearing the "populated" flag on the way.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Make the CONFIG_OF=n prototpe of of_node_full_name() mateh the CONFIG_OF=y
version.
Fixes compile warnings like this:
sound/soc/soc-core.c: In function 'soc_check_aux_dev':
sound/soc/soc-core.c:1667:3: warning: passing argument 1 of 'of_node_full_name' discards 'const' qualifier from pointer target type [enabled by default]
codecname = of_node_full_name(aux_dev->codec_of_node);
when CONFIG_OF is not defined.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The torture_parm() macro is the same as torture_param(), and torture_parm()
is not used. This commit therefore removes torture_parm().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The torture tests are designed to run in isolation, but do not enforce
this isolation. This commit therefore checks for concurrent torture
tests, and refuses to start new tests while old tests are running.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Given a CPU running a loop containing cond_resched(), with no
other tasks runnable on that CPU, RCU will eventually report RCU
CPU stall warnings due to lack of quiescent states. Fortunately,
every call to cond_resched() is a perfectly good quiescent state.
Unfortunately, invoking rcu_note_context_switch() is a bit heavyweight
for cond_resched(), especially given the need to disable preemption,
and, for RCU-preempt, interrupts as well.
This commit therefore maintains a per-CPU counter that causes
cond_resched(), cond_resched_lock(), and cond_resched_softirq() to call
rcu_note_context_switch(), but only about once per 256 invocations.
This ratio was chosen in keeping with the relative time constants of
RCU grace periods.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The definition for raw_cpu_add_return() uses the operation prefix
"raw_add_return_", but the definitions in the various percpu.h files
expect "raw_cpu_add_return_". This commit therefore appropriately
adjusts the definition of raw_cpu_add_return().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit allows rcutorture to print additional state for the
RCU grace-period kthreads in cases where RCU seems reluctant to
start a new grace period.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Add handling of OS Extended Properties descriptors from configfs interface.
One kind of "OS Descriptors" are "Extended Properties" descriptors, which
need to be specified per interface or per group of interfaces described
by an IAD. This patch adds support for creating subdirectories
in interface.<n> directory located in the function's directory.
Names of subdirectories created become names of properties.
Each property contains two attributes: "type" and "data".
The type can be a numeric value 1..7 while data is a blob interpreted
depending on the type specified.
The types are:
1 - unicode string
2 - unicode string with environment variables
3 - binary
4 - little-endian 32-bit
5 - big-endian 32-bit
6 - unicode string with a symbolic link
7 - multiple unicode strings
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add handling of OS Extended Compatibility descriptors from configfs interface.
Hosts which expect the "OS Descriptors" ask only for configurations @ index 0,
but linux-based USB devices can provide more than one configuration.
This patch adds marking one of gadget's configurations the configuration
to be reported at index 0, regardless of the actual sequence of usb_add_config
invocations used for adding the configurations. The configuration is selected
by creating a symbolic link pointing to it from the "os_desc" directory
located at the top of a gadget's directory hierarchy.
One kind of "OS Descriptors" are "Extended Compatibility Descriptors",
which need to be specified per interface. This patch adds interface.<n>
directory in function's configfs directory to represent each interface
defined by the function. Each interface's directory contains two attributes:
"compatible_id" and "sub_compatible_id", which represent 8-byte
strings to be reported to the host as the "Compatible ID" and "Sub Compatible
ID".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft’s
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft’s
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
net_get_random_once depends on the static keys infrastructure to patch up
the branch to the slow path during boot. This was realized by abusing the
static keys api and defining a new initializer to not enable the call
site while still indicating that the branch point should get patched
up. This was needed to have the fast path considered likely by gcc.
The static key initialization during boot up normally walks through all
the registered keys and either patches in ideal nops or enables the jump
site but omitted that step on x86 if ideal nops where already placed at
static_key branch points. Thus net_get_random_once branches not always
became active.
This patch switches net_get_random_once to the ordinary static_key
api and thus places the kernel fast path in the - by gcc considered -
unlikely path. Microbenchmarks on Intel and AMD x86-64 showed that
the unlikely path actually beats the likely path in terms of cycle cost
and that different nop patterns did not make much difference, thus this
switch should not be noticeable.
Fixes: a48e42920f ("net: introduce new macro net_get_random_once")
Reported-by: Tuomas Räsänen <tuomasjjrasanen@tjjr.fi>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for active queue tracking, meaning that the
blk-mq tagging maintains a count of active users of a tag set.
This allows us to maintain a notion of fairness between users,
so that we can distribute the tag depth evenly without starving
some users while allowing others to try unfair deep queues.
If sharing of a tag set is detected, each hardware queue will
track the depth of its own queue. And if this exceeds the total
depth divided by the number of active queues, the user is actively
throttled down.
The active queue count is done lazily to avoid bouncing that data
between submitter and completer. Each hardware queue gets marked
active when it allocates its first tag, and gets marked inactive
when 1) the last tag is cleared, and 2) the queue timeout grace
period has passed.
Signed-off-by: Jens Axboe <axboe@fb.com>
of_can_translate_address only checks some conditions for address
translation, but does not check other conditions like having range
properties. The checks it does do are redundant with
__of_address_translate. The only difference is printing a message or
not. Since we only have a single caller that does the full translation
anyway, just remove of_can_translate_address and quiet the error
message.
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Frank Rowand <frank.rowand@sonymobile.com>
Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
The rcutorture output currently does not distinguish between stalls in
the RCU implementation and stalls in the rcu_torture_writer() kthreads.
This commit therefore adds some diagnostics to help distinguish between
these two conditions, at least for the non-SRCU implementations. (SRCU
does not provide evidence of update-side forward progress by design.)
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Determining the css of a task usually requires RCU read lock as that's
the only thing which keeps the returned css accessible till its
reference is acquired; however, testing whether a task belongs to the
root can be performed without dereferencing the returned css by
comparing the returned pointer against the root one in init_css_set[]
which never changes.
Implement task_css_is_root() which can be invoked in any context.
This will be used by the scheduled cgroup_freezer change.
v2: cgroup no longer supports modular controllers. No need to export
init_css_set. Pointed out by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.
Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The kernfs open method - kernfs_fop_open() - inherited extra
permission checks from sysfs. While the vfs layer allows ignoring the
read/write permissions checks if the issuer has CAP_DAC_OVERRIDE,
sysfs explicitly denied open regardless of the cap if the file doesn't
have any of the UGO perms of the requested access or doesn't implement
the requested operation. It can be debated whether this was a good
idea or not but the behavior is too subtle and dangerous to change at
this point.
After cgroup got converted to kernfs, this extra perm check also got
applied to cgroup breaking libcgroup which opens write-only files with
O_RDWR as root. This patch gates the extra open permission check with
a new flag KERNFS_ROOT_EXTRA_OPEN_PERM_CHECK and enables it for sysfs.
For sysfs, nothing changes. For cgroup, root now can perform any
operation regardless of the permissions as it was before kernfs
conversion. Note that kernfs still fails unimplemented operations
with -EINVAL.
While at it, add comments explaining KERNFS_ROOT flags.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Wagin <avagin@gmail.com>
Tested-by: Andrey Wagin <avagin@gmail.com>
Cc: Li Zefan <lizefan@huawei.com>
References: http://lkml.kernel.org/g/CANaxB-xUm3rJ-Cbp72q-rQJO5mZe1qK6qXsQM=vh0U8upJ44+A@mail.gmail.com
Fixes: 2bd59d48eb ("cgroup: convert to kernfs")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the option to provide the flags for mmc capabilities as platform
data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the option to provide signal direction configuration and
feeback clock as platform data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull x86 fixes from Peter Anvin:
"A somewhat unpleasantly large collection of small fixes. The big ones
are the __visible tree sweep and a fix for 'earlyprintk=efi,keep'. It
was using __init functions with predictably suboptimal results.
Another key fix is a build fix which would produce output that simply
would not decompress correctly in some configuration, due to the
existing Makefiles picking up an unfortunate local label and mistaking
it for the global symbol _end.
Additional fixes include the handling of 64-bit numbers when setting
the vdso data page (a latent bug which became manifest when i386
started exporting a vdso with time functions), a fix to the new MSR
manipulation accessors which would cause features to not get properly
unblocked, a build fix for 32-bit userland, and a few new platform
quirks"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso, time: Cast tv_nsec to u64 for proper shifting in update_vsyscall()
x86: Fix typo in MSR_IA32_MISC_ENABLE_LIMIT_CPUID macro
x86: Fix typo preventing msr_set/clear_bit from having an effect
x86/intel: Add quirk to disable HPET for the Baytrail platform
x86/hpet: Make boot_hpet_disable extern
x86-64, build: Fix stack protector Makefile breakage with 32-bit userland
x86/reboot: Add reboot quirk for Certec BPC600
asmlinkage: Add explicit __visible to drivers/*, lib/*, kernel/*
asmlinkage, x86: Add explicit __visible to arch/x86/*
asmlinkage: Revert "lto: Make asmlinkage __visible"
x86, build: Don't get confused by local symbols
x86/efi: earlyprintk=efi,keep fix
blk-mq currently uses percpu_ida for tag allocation. But that only
works well if the ratio between tag space and number of CPUs is
sufficiently high. For most devices and systems, that is not the
case. The end result if that we either only utilize the tag space
partially, or we end up attempting to fully exhaust it and run
into lots of lock contention with stealing between CPUs. This is
not optimal.
This new tagging scheme is a hybrid bitmap allocator. It uses
two tricks to both be SMP friendly and allow full exhaustion
of the space:
1) We cache the last allocated (or freed) tag on a per blk-mq
software context basis. This allows us to limit the space
we have to search. The key element here is not caching it
in the shared tag structure, otherwise we end up dirtying
more shared cache lines on each allocate/free operation.
2) The tag space is split into cache line sized groups, and
each context will start off randomly in that space. Even up
to full utilization of the space, this divides the tag users
efficiently into cache line groups, avoiding dirtying the same
one both between allocators and between allocator and freeer.
This scheme shows drastically better behaviour, both on small
tag spaces but on large ones as well. It has been tested extensively
to show better performance for all the cases blk-mq cares about.
Signed-off-by: Jens Axboe <axboe@fb.com>
This allows us to avoid a non-atomic memset over ->atomic_flags as well
as killing lots of duplicate initializations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Introduce gpiod_get_optional() and gpiod_get_index_optional() helpers
that make it easier for drivers to handle optional GPIOs.
Currently in order to handle optional GPIOs, a driver needs to special
case error handling for -ENOENT, such as this:
gpio = gpiod_get(dev, "foo");
if (IS_ERR(gpio)) {
if (PTR_ERR(gpio) != -ENOENT)
return PTR_ERR(gpio);
gpio = NULL;
}
if (gpio) {
/* set up GPIO */
}
With these new helpers the above is reduced to:
gpio = gpiod_get_optional(dev, "foo");
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
/* set up GPIO */
}
While at it, device-managed variants of these functions are also
provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The framebuffer layer can be a loadable module, which forces
omapfb to be a module as well. However, this breaks the lcd
drivers, which are linked into the omapfb driver but each
have their own module_init() function. To solve this,
we split out the lcd drivers into separate modules and
export omapfb_register_panel, which is the only interface
required between the main omapfb driver and the lcd panel
drivers.
We also have to introduce a new Kconfig symbol for H3, since
that lcd driver has a dependency on TPS65010, which we can
express better in Kconfig than Makefile syntax.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On platforms that use cpufreq_for_each_* macros, build fails if
CONFIG_CPU_FREQ=n, e.g. ARM/shmobile/koelsch/non-multiplatform:
drivers/built-in.o: In function `clk_round_parent':
clkdev.c:(.text+0xcf168): undefined reference to `cpufreq_next_valid'
drivers/built-in.o: In function `clk_rate_table_find':
clkdev.c:(.text+0xcf820): undefined reference to `cpufreq_next_valid'
make[3]: *** [vmlinux] Error 1
Fix this making cpufreq_next_valid function inline and move it to
cpufreq.h.
Fixes: 27e289dce2 (cpufreq: Introduce macros for cpufreq_frequency_table iteration)
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that there are no architectures left using it, kill the support
for TS_POLLING.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/n/tip-6yurip2tfix2f4bfc5agu2s0@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If CONFIG_OF is not set, make of_mdiobus_register() call
mdiobus_register() instead of returning -ENOSYS.
This way, we can just call of_mdiobus_register() from all DT-enabled
drivers to handle the compat cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d206940319,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old ADCs, as present on the sam9rl and the sam9g45 don't have a TSMR register
and the touchscreen support should be handled differently.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
num_channels and registers are not used anymore since they are defined inside
the driver and assigned by matching the id_table.
Also, struct at91_adc_reg_desc is now only used inside the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AT91 slow clk is a clk multiplexer.
In some SoCs (sam9x5, sama5, sam9g45 families) this multiplexer can
choose among 2 sources: an internal RC oscillator circuit and an oscillator
using an external crystal.
In other Socs (sam9260 family) the multiplexer source is hardcoded with
the OSCSEL signal.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Right now we just pick the first CPU in the mask, but that can
easily overload that one. Add some basic batching and round-robin
all the entries in the mask instead.
Signed-off-by: Jens Axboe <axboe@fb.com>
A new flag SD_SHARE_POWERDOMAIN is created to reflect whether groups of CPUs
in a sched_domain level can or not reach different power state. As an example,
the flag should be cleared at CPU level if groups of cores can be power gated
independently. This information can be used in the load balance decision or to
add load balancing level between group of CPUs that can power gate
independantly.
This flag is part of the topology flags that can be set by arch.
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
Cc: schwidefsky@de.ibm.com
Cc: cmetcalf@tilera.com
Cc: benh@kernel.crashing.org
Cc: preeti@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1397209481-28542-5-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We replace the old way to configure the scheduler topology with a new method
which enables a platform to declare additionnal level (if needed).
We still have a default topology table definition that can be used by platform
that don't want more level than the SMT, MC, CPU and NUMA ones. This table can
be overwritten by an arch which either wants to add new level where a load
balance make sense like BOOK or powergating level or wants to change the flags
configuration of some levels.
For each level, we need a function pointer that returns cpumask for each cpu,
a function pointer that returns the flags for the level and a name. Only flags
that describe topology, can be set by an architecture. The current topology
flags are:
SD_SHARE_CPUPOWER
SD_SHARE_PKG_RESOURCES
SD_NUMA
SD_ASYM_PACKING
Then, each level must be a subset on the next one. The build sequence of the
sched_domain will take care of removing useless levels like those with 1 CPU
and those with the same CPU span and no more relevant information for
load balancing than its children.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux390@de.ibm.com
Cc: linux-ia64@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/1397209481-28542-2-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
yield_task_dl() is broken:
o it forces current to be throttled setting its runtime to zero;
o it sets current's dl_se->dl_new to one, expecting that dl_task_timer()
will queue it back with proper parameters at replenish time.
Unfortunately, dl_task_timer() has this check at the very beginning:
if (!dl_task(p) || dl_se->dl_new)
goto unlock;
So, it just bails out and the task is never replenished. It actually
yielded forever.
To fix this, introduce a new flag indicating that the task properly yielded
the CPU before its current runtime expired. While this is a little overdoing
at the moment, the flag would be useful in the future to discriminate between
"good" jobs (of which remaining runtime could be reclaimed, i.e. recycled)
and "bad" jobs (for which dl_throttled task has been set) that needed to be
stopped.
Reported-by: yjay.kim <yjay.kim@lge.com>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140429103953.e68eba1b2ac3309214e3dc5a@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If freeze_enter() is called, we want to bypass the current cpuidle
governor and always use the deepest available (that is, not disabled)
C-state, because we want to save as much energy as reasonably possible
then and runtime latency constraints don't matter at that point, since
the system is in a sleep state anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Aubrey Li <aubrey.li@linux.intel.com>
Patch 01f8fa4f01 "genirq: Allow forcing cpu affinity of interrupts" added
an irq_force_affinity() function, and 30ccf03b4a "clocksource: Exynos_mct:
Use irq_force_affinity() in cpu bringup" subsequently uses it. However, the
driver can be used with CONFIG_SMP disabled, but the function declaration
is only available for CONFIG_SMP, leading to this build error:
drivers/clocksource/exynos_mct.c:431:3: error: implicit declaration of function 'irq_force_affinity' [-Werror=implicit-function-declaration]
irq_force_affinity(mct_irqs[MCT_L0_IRQ + cpu], cpumask_of(cpu));
This patch introduces a dummy helper function for the non-SMP case
that always returns success, to get rid of the build error.
Since the patches causing the problem are marked for stable backports,
this one should be as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/5619084.0zmrrIUZLV@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CPUFreq specific helper functions for OPP (Operating Performance Points)
now use generic OPP functions that allow CPUFreq to be be moved back
into CPUFreq framework. This allows for independent modifications
or future enhancements as needed isolated to just CPUFreq framework
alone.
Here, we just move relevant code and documentation to make this part of
CPUFreq infrastructure.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cpufreq drivers were redundantly invoking the _begin() and _end()
APIs around frequency transitions, and this double invocation (one from
the cpufreq core and the other from the cpufreq driver) used to result
in a self-deadlock, leading to system hangs during boot. (The _begin()
API makes contending callers wait until the previous invocation is
complete. Hence, the cpufreq driver would end up waiting on itself!).
Now all such drivers have been fixed, but debugging this issue was not
very straight-forward (even lockdep didn't catch this). So let us add a
debug infrastructure to the cpufreq core to catch such issues more easily
in the future.
We add a new field called 'transition_task' to the policy structure, to keep
track of the task which is performing the frequency transition. Using this
field, we make note of this task during _begin() and print a warning if we
find a case where the same task is calling _begin() again, before completing
the previous frequency transition using the corresponding _end().
We have left out ASYNC_NOTIFICATION drivers from this debug infrastructure
for 2 reasons:
1. At the moment, we have no way to avoid a particular scenario where this
debug infrastructure can emit false-positive warnings for such drivers.
The scenario is depicted below:
Task A Task B
/* 1st freq transition */
Invoke _begin() {
...
...
}
Change the frequency
/* 2nd freq transition */
Invoke _begin() {
... //waiting for B to
... //finish _end() for
... //the 1st transition
... | Got interrupt for successful
... | change of frequency (1st one).
... |
... | /* 1st freq transition */
... | Invoke _end() {
... | ...
... V }
...
...
}
This scenario is actually deadlock-free because, once Task A changes the
frequency, it is Task B's responsibility to invoke the corresponding
_end() for the 1st frequency transition. Hence it is perfectly legal for
Task A to go ahead and attempt another frequency transition in the meantime.
(Of course it won't be able to proceed until Task B finishes the 1st _end(),
but this doesn't cause a deadlock or a hang).
The debug infrastructure cannot handle this scenario and will treat it as
a deadlock and print a warning. To avoid this, we exclude such drivers
from the purview of this code.
2. Luckily, we don't _need_ this infrastructure for ASYNC_NOTIFICATION drivers
at all! The cpufreq core does not automatically invoke the _begin() and
_end() APIs during frequency transitions in such drivers. Thus, the driver
alone is responsible for invoking _begin()/_end() and hence there shouldn't
be any conflicts which lead to double invocations. So, we can skip these
drivers, since the probability that such drivers will hit this problem is
extremely low, as outlined above.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
agp: info leak in agpioc_info_wrap()
fs/affs/super.c: bugfix / double free
fanotify: fix -EOVERFLOW with large files on 64-bit
slub: use sysfs'es release mechanism for kmem_cache
revert "mm: vmscan: do not swap anon pages just because free+file is low"
autofs: fix lockref lookup
mm: filemap: update find_get_pages_tag() to deal with shadow entries
mm/compaction: make isolate_freepages start at pageblock boundary
MAINTAINERS: zswap/zbud: change maintainer email address
mm/page-writeback.c: fix divide by zero in pos_ratio_polynom
hugetlb: ensure hugepage access is denied if hugepages are not supported
slub: fix memcg_propagate_slab_attrs
drivers/rtc/rtc-pcf8523.c: fix month definition
Currently, I am seeing the following when I `mount -t hugetlbfs /none
/dev/hugetlbfs`, and then simply do a `ls /dev/hugetlbfs`. I think it's
related to the fact that hugetlbfs is properly not correctly setting
itself up in this state?:
Unable to handle kernel paging request for data at address 0x00000031
Faulting instruction address: 0xc000000000245710
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2048 NUMA pSeries
....
In KVM guests on Power, in a guest not backed by hugepages, we see the
following:
AnonHugePages: 0 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 64 kB
HPAGE_SHIFT == 0 in this configuration, which indicates that hugepages
are not supported at boot-time, but this is only checked in
hugetlb_init(). Extract the check to a helper function, and use it in a
few relevant places.
This does make hugetlbfs not supported (not registered at all) in this
environment. I believe this is fine, as there are no valid hugepages
and that won't change at runtime.
[akpm@linux-foundation.org: use pr_info(), per Mel]
[akpm@linux-foundation.org: fix build when HPAGE_SHIFT is undefined]
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs fixes from Al Viro:
"dcache fixes + kvfree() (uninlined, exported by mm/util.c) + posix_acl
bugfix from hch"
The dcache fixes are for a subtle LRU list corruption bug reported by
Miklos Szeredi, where people inside IBM saw list corruptions with the
LTP/host01 test.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
nick kvfree() from apparmor
posix_acl: handle NULL ACL in posix_acl_equiv_mode
dcache: don't need rcu in shrink_dentry_list()
more graceful recovery in umount_collect()
don't remove from shrink list in select_collect()
dentry_kill(): don't try to remove from shrink list
expand the call of dentry_lru_del() in dentry_kill()
new helper: dentry_free()
fold try_prune_one_dentry()
fold d_kill() and d_free()
fix races between __d_instantiate() and checks of dentry flags
This set contains a change to the ABI for the hid-sensors drivers to bring them
in line with the long published documentation. Unfortunately, rather than
reporting true scale and offset values via sysfs they were reporting
some magic numbers that could only be converted to anything useful using
the HID sensors specification. I missed this entirely through the introduction
of a number of drivers, only picking up on it recently. Srinivas has had
user feedback about this as well. The patch set is too large to go as a fix
at this stage in the cycle and is not a regression fix as this was never
right and so will have to wait for the next merge window. Srinivas assures
me that there are relatively few pieces of hardware out there and he has
had a number of people contact him to point out that the drivers did not
obey the ABI. Hence hopefully the fallout of this, if any will be minor.
If we don't fix it now, it will only get worse going forward. There is no
sensible way of maintaining the incorrect ABI as it is simply returning
the wrong values through the standard interfaces.
Non IIO elements
* Introduce devm_kmemdup. Does what it says on the tin.
New drivers:
* hid-sensors rotation devices (output as quaternion)
* Freescale MPL115A2 presure and temperature sensor.
* Melexis mlx90614 contactless infrared sensor.
* Freescale MMA8452Q 3-axis accelerometer.
New functionality:
* Addition of multiple element callback to allow for sysfs interfaces to access
elements such as quaternions which have no useful meaning if all 4 elements
are not presented together. Other future usecases for this include
rotation matrices.
* Support for multiple element buffer entries for exactly the same uses as
the sysfs related elements described above.
* Quaternion support via the quaternion IIO modifier.
* TEMP_AMBIENT and TEMP_OBJECT modifiers to distinguish cases with thermopile
devices.
* hid-sensors gain sysfs access to the sensor readings. Previously these
drivers used the buffered interface only. This change involves some
additional hid-sensors core support to read poll values back from the devices
to allow the drivers to know roughly how long to wait for a result when
polling the sensor. There is also an associated hid-sensors abi to allow
the devices to be turned off between reads and powered up on demand.
Cleanups and fixes
* Hid sensors fix as described above. Result is to make the _scale and _offset
attributes applicable in the same way as for all other IIO drivers.
* Some additional documentation - mostly covering stuff that graduated from
staging without managing to take it's ABI docs with it.
* A series of little tidy ups to the exynos_adc driver that make the code
nicer to read and improve handling of some corner cases.
* A tidy up to mag3110 (logical fix rather than a real one ;). Also enable
user offset calibration for this device.
* Drop some left over IS_ERR() checks from ad799x that snuck through during
the cleanup in the last IIO patch set.
* Fix a naming issue from clashing patches in ak8975 - note the clash only
occured in the last IIO patch set, hence the fix needs to go through this
tree.
* A format string missmatch fix in ad7280.c. Unlikely to have ever had an
impact so not worth rushing through.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ghZG
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.16b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new drivers, cleanups and functionality for the 3.16 cycle.
This set contains a change to the ABI for the hid-sensors drivers to bring them
in line with the long published documentation. Unfortunately, rather than
reporting true scale and offset values via sysfs they were reporting
some magic numbers that could only be converted to anything useful using
the HID sensors specification. I missed this entirely through the introduction
of a number of drivers, only picking up on it recently. Srinivas has had
user feedback about this as well. The patch set is too large to go as a fix
at this stage in the cycle and is not a regression fix as this was never
right and so will have to wait for the next merge window. Srinivas assures
me that there are relatively few pieces of hardware out there and he has
had a number of people contact him to point out that the drivers did not
obey the ABI. Hence hopefully the fallout of this, if any will be minor.
If we don't fix it now, it will only get worse going forward. There is no
sensible way of maintaining the incorrect ABI as it is simply returning
the wrong values through the standard interfaces.
Non IIO elements
* Introduce devm_kmemdup. Does what it says on the tin.
New drivers:
* hid-sensors rotation devices (output as quaternion)
* Freescale MPL115A2 presure and temperature sensor.
* Melexis mlx90614 contactless infrared sensor.
* Freescale MMA8452Q 3-axis accelerometer.
New functionality:
* Addition of multiple element callback to allow for sysfs interfaces to access
elements such as quaternions which have no useful meaning if all 4 elements
are not presented together. Other future usecases for this include
rotation matrices.
* Support for multiple element buffer entries for exactly the same uses as
the sysfs related elements described above.
* Quaternion support via the quaternion IIO modifier.
* TEMP_AMBIENT and TEMP_OBJECT modifiers to distinguish cases with thermopile
devices.
* hid-sensors gain sysfs access to the sensor readings. Previously these
drivers used the buffered interface only. This change involves some
additional hid-sensors core support to read poll values back from the devices
to allow the drivers to know roughly how long to wait for a result when
polling the sensor. There is also an associated hid-sensors abi to allow
the devices to be turned off between reads and powered up on demand.
Cleanups and fixes
* Hid sensors fix as described above. Result is to make the _scale and _offset
attributes applicable in the same way as for all other IIO drivers.
* Some additional documentation - mostly covering stuff that graduated from
staging without managing to take it's ABI docs with it.
* A series of little tidy ups to the exynos_adc driver that make the code
nicer to read and improve handling of some corner cases.
* A tidy up to mag3110 (logical fix rather than a real one ;). Also enable
user offset calibration for this device.
* Drop some left over IS_ERR() checks from ad799x that snuck through during
the cleanup in the last IIO patch set.
* Fix a naming issue from clashing patches in ak8975 - note the clash only
occured in the last IIO patch set, hence the fix needs to go through this
tree.
* A format string missmatch fix in ad7280.c. Unlikely to have ever had an
impact so not worth rushing through.
Jean Delvare