A number of places treated features wrongly, listing not-supported
features instead of supported ones. Also, the get_drvinfo ethtool
callback isn't needed, and alx_get_pauseparam can be simplified.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In two places, parts of MAC addresses are used as u32/u16
values. This can cause alignment problems, use put_unaligned
and get_unaligned to fix this.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Ben Hutchings, use separate fields to track
current link speed and duplex setting.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring sizes should be unsigned, pointed out by Ben Hutchings.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
That select doesn't make any sense, remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
100mbit half duplex is ADVERTISED_100baseT_Half, not
ADVERTISED_10baseT_Half.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when alx_setup_speed_duplex() is called, we still
need to call alx_cfg_mac_flowcontrol() and set hw->flowctrl
if flow control changed.
This was a bug I accidentally introduced while simplifying
the original driver.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.
This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).
To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.
If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for net-next,
they are:
* Enforce policy to several nfnetlink subsystem, from Daniel
Borkmann.
* Use xt_socket to match the third packet (to perform simplistic
socket-based stateful filtering), from Eric Dumazet.
* Avoid large timeout for picked up from the middle TCP flows,
from Florian Westphal.
* Exclude IPVS from struct net if IPVS is disabled and removal
of unnecessary included header file, from JunweiZhang.
* Release SCTP connection immediately under load, to mimic current
TCP behaviour, from Julian Anastasov.
* Replace and enhance SCTP state machine, from Julian Anastasov.
* Add tweak to reduce sync traffic in the presence of persistence,
also from Julian Anastasov.
* Add tweak for the IPVS SH scheduler not to reject connections
directed to a server, choose a new one instead, from Alexander
Frolkin.
* Add support for sloppy TCP and SCTP modes, that creates state
information on any packet, not only initial handshake packets,
from Alexander Frolkin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The common case is that TCP/IP checksums have already been
verified, e.g. by hardware (rx checksum offload), or conntrack.
Userspace can use this flag to determine when the checksum
has not been validated yet.
If the flag is set, this doesn't necessarily mean that the packet has
an invalid checksum, e.g. if NIC doesn't support rx checksum.
Userspace that sucessfully enabled NFQA_CFG_F_GSO queue feature flag can
infer that IP/TCP checksum has already been validated if either the
SKB_INFO attribute is not present or the NFQA_SKB_CSUM_NOTVERIFIED
flag is unset.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Combine the multiple pr_debugs in bond_set_dev_addr into one pr_debug.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. It consists of three
patches by Fabio Estevam and me, which convert the flexcan transceiver
switching to DT[1] and a patch by Sachin Kamat, which cleans up the
at91_can driver a bit.
[1] These patches touch arch/arm/mach-imx, so I collected Acked-bys
from Shawn Guo and Sascha Hauer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning introduced in e4fc408e0e
("packet: nlmon: virtual netlink monitoring device for packet
sockets") reported by Dan Carpenter:
warning: "drivers/net/nlmon.c:31 nlmon_is_valid_mtu()
warn: always true condition '(new_mtu <= ((~0 >> 1))) =>
(s32min-s32max <= s32max)'"
Thus, we should simply remove the test against INT_MAX. Next to that
we also need to explicitly cast the sizeof() case as the comparison
is type promoted to unsigned long so negative values are then
valid instead of invalid. While at it, this also adds a comment about
Netlink and MTUs.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to add a newline after logging the device's MACID.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the error handling much more simpler than open-coding everything and
in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may use nice macros to prefix our messages with proper device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no much sense to mark functions inline that are going to be used in
the other compile modules.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested with the AX88179 usb dongle, if without .reset_resume hook,
after S3/S4 resume you have to enable network interface or reload the
dirver module manually otherwise the network interface can not work.
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a typo in description of driver_info, it should be Gigabit
Signed-off-by: David Chang <dchang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d2d68ba9 (ipv4: Cache input routes in fib_info nexthops)
assmued that "locally destined, and routed packets, never trigger
PMTU events or redirects that will be processed by us".
However, it seems that tunnel devices do trigger PMTU events in certain
cases. At least ip_gre, ip6_gre, sit, and ipip do use the inner flow's
skb_dst(skb)->ops->update_pmtu to propage mtu information from the
outer flows. These can cause the inner flow mtu to be decreased. If
next hop exceptions are not consulted for pmtu, IP fragmentation will
not be done properly for these routes.
It also seems that we really need to have the PMTU information always
for netfilter TCPMSS clamp-to-pmtu feature to work properly.
So for the time being, cache separate copies of input routes for
each next hop exception.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3590/RFC3810 specifies we should resend MLD reports as soon as a
valid link-local address is available.
We now use the valid_ll_addr_cnt to check if it is necessary to resend
a new report.
Changes since Flavio Leitner's version:
a) adapt for valid_ll_addr_cnt
b) resend first reports directly in the path and just arm the timer for
mc_qrv-1 resends.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the number of unnecessary router solicitations, MLDv2 and IGMPv3
messages we need to track the number of valid (as in non-optimistic,
no-dad-failed and non-tentative) link-local addresses. Therefore, this
patch implements a valid_ll_addr_cnt in struct inet6_dev.
We now only emit router solicitations if the first link-local address
finishes duplicate address detection.
The changes for MLDv2 and IGMPv3 are in a follow-up patch.
While there, also simplify one if statement(one minor nit I made in one
of my previous patches):
if (!...)
do();
else
return;
<<into>>
if (...)
return;
do();
Cc: Flavio Leitner <fbl@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Suggested-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple semantic change, when a slave's MAC is cloned by the bond
master then set addr_assign_type to NET_ADDR_STOLEN instead of
NET_ADDR_SET. Also use bond_set_dev_addr() in BOND_FOM_ACTIVE mode
to change the bond's MAC address because the assign_type has to be
set properly.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct bonding there's a member called dev_addr_from_first which is
used to denote when the bond dev should clone the first slave's MAC
address but since we have netdev's addr_assign_type variable that is not
necessary. We clone the first slave's MAC each time we have a random MAC
set to the bond device. This has the nice side-effect of also fixing an
inconsistency - when the MAC address of the bond dev is set after its
creation, but prior to having slaves, it's not kept and the first slave's
MAC is cloned. The only way to keep the MAC was to create the bond device
with the MAC address set (e.g. through ip link). In all cases if the
bond device is left without any slaves - its MAC gets reset to a random
one as before.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a member called setup_by_slave in struct bonding to denote if the
bond dev has different type than ARPHRD_ETHER, but that is already denoted
in bond's netdev type variable if it was setup by the slave, so use that
instead of the member.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since (c05cdb1 netlink: allow large data transfers from user-space),
netlink splats if it invokes skb_clone on large netlink skbs since:
* skb_shared_info was not correctly initialized.
* skb->destructor is not set in the cloned skb.
This was spotted by trinity:
[ 894.990671] BUG: unable to handle kernel paging request at ffffc9000047b001
[ 894.991034] IP: [<ffffffff81a212c4>] skb_clone+0x24/0xc0
[...]
[ 894.991034] Call Trace:
[ 894.991034] [<ffffffff81ad299a>] nl_fib_input+0x6a/0x240
[ 894.991034] [<ffffffff81c3b7e6>] ? _raw_read_unlock+0x26/0x40
[ 894.991034] [<ffffffff81a5f189>] netlink_unicast+0x169/0x1e0
[ 894.991034] [<ffffffff81a601e1>] netlink_sendmsg+0x251/0x3d0
Fix it by:
1) introducing a new netlink_skb_clone function that is used in nl_fib_input,
that sets our special skb->destructor in the cloned skb. Moreover, handle
the release of the large cloned skb head area in the destructor path.
2) not allowing large skbuffs in the netlink broadcast path. I cannot find
any reasonable use of the large data transfer using netlink in that path,
moreover this helps to skip extra skb_clone handling.
I found two more netlink clients that are cloning the skbs, but they are
not in the sendmsg path. Therefore, the sole client cloning that I found
seems to be the fib frontend.
Thanks to Eric Dumazet for helping to address this issue.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this new function is to perform all needed cleanup before sending
an skb into another netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_match_ptr() eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As there are no more users of the flexcan platform file, let's remove it.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As there are no imx in-tree users of flexcan_platform_data, this patch removes
the possibility to register a flexcan device with platform data.
The functionality to swith on/off CAN transceivers is added to DT via
regulators in a later patch.
Compile time tested with imx_v4_v5_defconfig and imx_v6_v7_defconfig.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new tokenized address gets installed we send out just one
router solicition. We should send out `rtr_solicits' in case one router
advertisment got lost.
So, rearm the timer as we do in addrconf_dad_complete.
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 32b8a8e59c "sit: add IPv4 over IPv4 support",
tunnel->parms.iph.protocol is 0 when both 4in4 and 6in4 are setup, but
xfrm_lookup() is called only when proto is != 0, thus we need to pass the real
value.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
Just one patch this time.
1) Drop packets when the matching SA is in larval state and add a
statistic counter for that. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
no real problem is fixed, just save a few bytes in
net_namespace structure.
Signed-off-by: JunweiZhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs.h is not necessary for sysctl_binary.c.
prepare for the next patch to avoid compile issue.
Signed-off-by: JunweiZhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add sync_persist_mode flag to reduce sync traffic
by syncing only persistent templates.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
By default the SH scheduler rejects connections that are hashed onto a
realserver of weight 0. This patch adds a flag to make SH choose a
different realserver in this case, instead of rejecting the connection.
The patch also adds a flag to make SH include the source port (TCP, UDP,
SCTP) in the hash as well as the source address. This basically allows
for deterministic round-robin load balancing (i.e., where any director
in a cluster of directors with identical config will send the same
packet the same way).
The flags are service flags (IP_VS_SVC_F_SCHED*) so that these options
can be set per service. They are set using a new option to ipvsadm.
Signed-off-by: Alexander Frolkin <avf@eldamar.org.uk>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Drop SCTP connections under load (dropentry context) depending
on the protocol state, just like for TCP: INIT conns are
dropped immediately, established are dropped randomly while
connections in progress or shutdown are skipped.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Convert the SCTP state table, so that it is more readable.
Change the states to be according to the diagram in RFC 2960
and add more states suitable for middle box. Still, such
change in states adds incompatibility if systems in sync
setup include this change and others do not include it.
With this change we also have proper transitions in INPUT-ONLY
mode (DR/TUN) where we see packets only from client. Now
we should not switch to 10-second CLOSED state at a time
when we should stay in ESTABLISHED state.
The short names for states are because we have 16-char space
in ipvsadm and 11-char limit for the connection list format.
It is a sequence of the TCP implementation where the longest
state name is ESTABLISHED.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
This adds support for sloppy TCP and SCTP modes to IPVS.
When enabled (sysctls net.ipv4.vs.sloppy_tcp and
net.ipv4.vs.sloppy_sctp), allows IPVS to create connection state on any
packet, not just a TCP SYN (or SCTP INIT).
This allows connections to fail over from one IPVS director to another
mid-flight.
Signed-off-by: Alexander Frolkin <avf@eldamar.org.uk>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Before now the schedulers needed access only to IP
addresses and it was easy to get them from skb by
using ip_vs_fill_iph_addr_only.
New changes for the SH scheduler will need the protocol
and ports which is difficult to get from skb for the
IPv6 case. As we have all the data in the iph structure,
to avoid the same slow lookups provide the iph to schedulers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
As reported by "kbuild test robot" there were some errors and warnings
on attempt to build kernel with "make ARCH=powerpc allmodconfig".
And this patch addresses both errors and warnings.
Below is a list of introduced changes:
1. Fix compile-time errors (misspellings in "dma_unmap_single") on PPC.
2. Use DMA address instead of "skb->data" as a pointer to data buffer.
This fixed warnings on pointer to int conversion on 64-bit systems.
3. Re-implemented initial allocation of Rx buffers in "arc_emac_open" in
the same way they're re-allocated during operation (receiving packets).
So once again DMA address could be used instead of "skb->data".
4. Explicitly use EMAC_BUFFER_SIZE for Rx buffers allocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: netdev@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we fail only when all of the ips in arp_ip_target are gone.
However, in some situations we might need to fail if even one host from
arp_ip_target becomes unavailable.
All situations, obviously, rely on the idea that we need *completely*
functional network, with all interfaces/addresses working correctly.
One real world example might be:
vlans on top on bond (hybrid port). If bond and vlans have ips assigned
and we have their peers monitored via arp_ip_target - in case of switch
misconfiguration (trunk/access port), slave driver malfunction or
tagged/untagged traffic dropped on the way - we will be able to switch
to another slave.
Though any other configuration needs that if we need to have access to all
arp_ip_targets.
This patch adds this possibility by adding a new parameter -
arp_all_targets (both as a module parameter and as a sysfs knob). It can be
set to:
0 or any (the default) - which works exactly as it's working now -
the slave is up if any of the arp_ip_targets are up.
1 or all - the slave is up if all of the arp_ip_targets are up.
This parameter can be changed on the fly (via sysfs), and requires the mode
to be active-backup and arp_validate to be enabled (it obeys the
arp_validate config on which slaves to validate).
Internally it's done through:
1) Add target_last_arp_rx[BOND_MAX_ARP_TARGETS] array to slave struct. It's
an array of jiffies, meaning that slave->target_last_arp_rx[i] is the
last time we've received arp from bond->params.arp_targets[i] on this
slave.
2) If we successfully validate an arp from bond->params.arp_targets[i] in
bond_validate_arp() - update the slave->target_last_arp_rx[i] with the
current jiffies value.
3) When getting slave's last_rx via slave_last_rx(), we return the oldest
time when we've received an arp from any address in
bond->params.arp_targets[].
If the value of arp_all_targets == 0 - we still work the same way as
before.
Also, update the documentation to reflect the new parameter.
v3->v4:
Kill the forgotten rtnl_unlock(), rephrase the documentation part to be
more clear, don't fail setting arp_all_targets if arp_validate is not set -
it has no effect anyway but can be easier to set up. Also, print a warning
if the last arp_ip_target is removed while the arp_interval is on, but not
the arp_validate.
v2->v3:
Use _bh spinlock, remove useless rtnl_lock() and use jiffies for new
arp_ip_target last arp, instead of slave_last_rx(). On bond_enslave(),
use the same initialization value for target_last_arp_rx[] as is used
for the default last_arp_rx, to avoid useless interface flaps.
Also, instead of failing to remove the last arp_ip_target just print a
warning - otherwise it might break existing scripts.
v1->v2:
Correctly handle adding/removing hosts in arp_ip_target - we need to
shift/initialize all slave's target_last_arp_rx. Also, don't fail module
loading on arp_all_targets misconfiguration, just disable it, and some
minor style fixes.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some details to bonding documentation on how backup slave arp
validation works.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg