All we do is write the length/status and address bits to a DMA
descriptor only to write its contents into on-chip registers right
after, eliminate this unnecessary step.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch the socket address family sporadically gets wrong
value ends up the dev_set_mac_address() fails to set the desired MAC
address.
Fixes: 25766271e4 ("r8152: Refresh MAC address during USBDEVFS_RESET")
Signed-off-by: Crag.Wang <crag.wang@dell.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-By: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Shared buffer improvements
This patchset includes two improvements with regards to shared buffer
configuration in mlxsw.
The first part of this patchset forbids the user from performing illegal
shared buffer configuration that can result in unnecessary packet loss.
In order to better communicate these configuration failures to the user,
extack is propagated from devlink towards drivers. This is done in
patches #1-#8.
The second part of the patchset deals with the shared buffer
configuration of the CPU port. When a packet is trapped by the device,
it is sent across the PCI bus to the attached host CPU. From the
device's perspective, it is as if the packet is transmitted through the
CPU port.
While testing traffic directed at the CPU it became apparent that for
certain packet sizes and certain burst sizes, the current shared buffer
configuration of the CPU port is inadequate and results in packet drops.
The configuration is adjusted by patches #9-#14 that create two new pools
- ingress & egress - which are dedicated for CPU traffic.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the CPU port to use the new dedicated egress pool instead the
previously used egress pool which was shared with normal front panel
ports.
Add per-port quotas for the amount of traffic that can be buffered for
the CPU port and also adjust the per-{port, TC} quotas.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port is used to transmit traffic that is trapped to the host
CPU. It is therefore irrelevant to define ingress quota for it.
Add a 'skip_ingress' argument to the function tasked with configuring
per-port quotas, so that ingress quotas could be skipped in case the
passed local port is the CPU port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is used to set the per-port shared buffer quotas.
Currently, these quotas are only set for front panel ports, but a
subsequent patch will configure these quotas for the CPU port as well.
The configuration required for the CPU port is a bit different than that
of the front panel ports, so split the business logic into a separate
function which will be called with different parameters for the CPU
port.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ingress pool that was added in the previous patch for
control packets (e.g., STP, LACP) that are trapped to the CPU.
The previous management pool is no longer necessary and therefore its
size is set to 0.
The maximum quota for traffic towards the CPU is increased to 50% of the
free space in the new ingress pool and therefore the reserved space is
reduced by half, to 10KB - in both the shared and headroom buffer. This
allows for more efficient utilization of the shared buffer as reserved
space cannot be used for other purposes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are trapped to the CPU are transmitted through the CPU port
to the attached host. The CPU port is therefore like any other port and
needs to have shared buffer configuration.
The maximum quotas configured for the CPU are provided using dynamic
threshold and cannot be changed by the user. In order to make sure that
these thresholds are always valid, the configuration of the threshold
type of these pools is forbidden.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently assumes that ingress pools have lower indices than
egress pools. This makes it impossible to add more ingress pools
without breaking user configuration that relies on a certain pool index
to correspond to an egress pool.
Remove such assumptions from the code, so that more ingress pools could
be added by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool")
configured the threshold of the multicast TCs as infinite so that the
admission of multicast packets is only depended on per-switch priority
threshold.
Forbid the user from changing the thresholds of these multicast TCs and
their binding to a different pool.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast packets have three egress quotas:
* Per egress port
* Per egress port and traffic class
* Per switch priority
The limits on the switch priority are not exposed to the user and
specified as dynamic threshold on the first egress pool.
Forbid changing the threshold type of the first egress pool so that
these limits are always valid.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool") added
a dedicated pool for multicast traffic. The pool is visible to the user
so that it would be possible to monitor its occupancy, but its
configuration should be forbidden in order to maintain its intended
operation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to need to veto changes in certain TCs'
binding and threshold configurations.
Add fields to the TC's struct that indicate if the TC can be bound to a
different pool and whether its threshold can change and enforce that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to need to veto changes in certain pools'
size and / or threshold type (mode).
Add two fields to the pool's struct that indicate if either of these
attributes is allowed to change and enforce that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pool indices are currently hard coded throughout the code, which
makes the code hard to follow and extend.
Overcome this by using defines for the pool indices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to shared buffer set operations, so that meaningful error
messages could be propagated to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker says:
====================
clean up needless use of module infrastructure
People can embed modular includes and modular exit functions into code
that never use any of it, and they won't get any errors or warnings.
Using modular infrastructure in non-modules might seem harmless, but some
of the downfalls this leads to are:
(1) it is easy to accidentally write unused module_exit removal code
(2) it can be misleading when reading the source, thinking a driver can
be modular when the Makefile and/or Kconfig prohibit it
(3) an unused include of the module.h header file will in turn
include nearly everything else; adding a lot to CPP overhead.
(4) it gets copied/replicated into other drivers and spreads quickly.
As a data point for #3 above, an empty C file that just includes the
module.h header generates over 750kB of CPP output. Repeating the same
experiment with init.h and the result is less than 12kB; with export.h
it is only about 1/2kB; with both it still is less than 12kB. One driver
in this series gets the module.h ---> init.h+export.h conversion.
Worse, are headers in include/linux that in turn include <linux/module.h>
as they can impact a whole fleet of drivers, or a whole subsystem, so
special care should be used in order to avoid that. Such headers should
only include what they need to be stand-alone; they should not be trying
to anticipate the various header needs of their possible end users.
In this series, four include/linux headers have module.h removed from
them because they don't strictly need it. Then three chunks of net
related code have modular infrastructure that isn't used, removed.
There are no runtime changes, so the biggest risk is a genuine consumer
of module.h content relying on implicitly getting it from one of the
include/linux instances removed here - thus resulting in a build fail.
With that in mind, allmodconfig build testing was done on x86-64, arm64,
x86-32, arm. powerpc, and mips on linux-next (and hence net-next).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
net/strparser/Kconfig:config STREAM_PARSER
net/strparser/Kconfig: def_bool n
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. For
clarity, we change the fcn name mod_init to dev_init at the same time.
We replace module.h with init.h and export.h ; the latter since this
file exports some syms.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig controlling this code is:
bpfilter/Kconfig:menuconfig BPFILTER
bpfilter/Kconfig: bool "BPF based packet filtering framework (BPFILTER)"
Since it isn't a module, we shouldn't use module_init(). Instead we
use device_initcall() - which is exactly what module_init() defaults
to for non-modular code/builds.
We don't remove <linux/module.h> from the includes since this file does
a request_module() and hence is a valid user of that header file, even
though it is not modular itself.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
net/Kconfig:config CGROUP_NET_PRIO
net/Kconfig: bool "Network priority cgroup"
...meaning that it currently is not being built as a module by anyone,
as module support was discontinued in 2014.
We delete the MODULE_LICENSE tag since all that information is already
contained at the top of the file in the comments.
We don't delete module.h from the includes since it was no longer there
to begin with.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rosen, Rami" <rami.rosen@intel.com>
Cc: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since tc_ife.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since fib_notifier.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
There doesn't appear to be anything in net/ife.h that is module
related, and build coverage doesn't appear to show any other
files/drivers relying implicitly on getting it from here.
So it appears we are simply free to just remove it in this case.
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
There doesn't appear to be anything in psample.h that is module
related, and build coverage doesn't appear to show any other
files/drivers relying implicitly on getting it from here.
So it appears we are simply free to just remove it in this case.
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header contains rtnh_ macros so rename the file accordingly.
Allows a later patch to use the nexthop.h name for the new
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes trivial whitespace fix to the function
tcp_v4_check at include/net/tcp.h file.
It has stylistic issue, which is "space required after that ','"
and it can be confirmed with ./scripts/checkpatch.pl tool.
ERROR: space required after that ',' (ctx:VxV)
#29: FILE: include/net/tcp.h:1317:
+ return csum_tcpudp_magic(saddr,daddr,len,IPPROTO_TCP,base);
^
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-04-22
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) allow stack/queue helpers from more bpf program types, from Alban.
2) allow parallel verification of root bpf programs, from Alexei.
3) introduce bpf sysctl hook for trusted root cases, from Andrey.
4) recognize var/datasec in btf deduplication, from Andrii.
5) cpumap performance optimizations, from Jesper.
6) verifier prep for alu32 optimization, from Jiong.
7) libbpf xsk cleanup, from Magnus.
8) other various fixes and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
Allow the bpf verifier to run in parallel for root.
====================
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Drop bpf_verifier_lock for root to avoid being DoS-ed by unprivileged.
The BPF verifier is now fully parallel.
All unpriv users are still serialized by bpf_verifier_lock to avoid
exhausting kernel memory by running N parallel verifications.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Move three global variables protected by bpf_verifier_lock into
'struct bpf_verifier_env' to allow parallel verification.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The RTF_ADDRCONF flag filters out routes added by RA's in determining
which routes can be appended to an existing one to create a multipath
route. Restore the flag check and add a comment to document the RA piece.
Fixes: 4e54507ab1 ("ipv6: Simplify rt6_qualify_for_ecmp")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use
ip6_route_info_create"), the gateway is no longer filled in for fib6_nh
structs in a prefix route. Accordingly, the RTF_ADDRCONF flag check can
be dropped from the 'rt6_qualify_for_ecmp'.
Further, RTF_DYNAMIC is only set in rt6_info instances, so it can be
removed from the check as well.
This reduces rt6_qualify_for_ecmp and the mlxsw version to just checking
if the nexthop has a gateway which is the real indication of whether
entries can be coalesced into a multipath route.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer should be printed with %p or %px rather than
cast to unsigned long type and printed with %08lx.
Change %08lx to %p to print the pointer.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers should be printed with %p or %px rather than
cast to long type and printed with %8.8lx.
Change %8.8lx to %p to print the pointer.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers should be printed with %p or %px rather than
cast to long type and printed with %x.
Change %x to %p to print the pointers.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Small routing improvements
Patch #1 switches the driver to use a unique and stable ECMP/LAG seed.
This allows for consistent behavior across reboots and avoids hash
polarization at the same time.
Patch #2 relaxes the FIB rule validation in the driver to allow the
installation of rules that direct locally generated traffic (iif=lo).
This does not result in a discrepancy between both data paths because
packets received by the device would never match such rules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw does not support policy-based routing (PBR) and
therefore forbids the installation of non-default FIB rules except for
the l3mdev rule which is used for VRFs.
Relax the check to allow the installation of FIB rules that would never
match packets received by the device. Specifically, if the iif is that
of the loopback netdev. This is useful for users that need to redirect
locally generated packets based on FIB rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get a consistent behavior of traffic flows across reboots /
module unload, we need to use the same ECMP/LAG seed.
Calculate the seed by hashing the base MAC of the device. This results
in a seed that is both unique (to avoid polarization) and consistent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default VFs are not trusted. Add ndo_set_vf_trust support to toggle
a new per-VF bit. Coupled with FW with this capability allows a
trusted VF to change its MAC even after being administratively set by
the PF. Also populate the trusted field on ndo_get_vf_config. Add the
same ndo to the representors.
Signed-off-by: Pablo Cascón <pablo.cascon@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: add some DFX info for HNS3 driver
This patch-set adds some DFX information to HNS3 driver, for easily
debug some problems, and fixes some related bugs.
[patch 1/12 - 4/12] adds debug info about reset & interrupt events
[patch 5/12 - 7/12] adds debug info about TX time out & fixes
related bugs
[patch 8/12] adds support for setting netif message level
[patch 9/12 - 10/12] adds debugfs command to dump NCL & MAC info
[patch 11/12] adds VF's queue statistics info updating
[patch 12/12] adds a check for debugfs help function to decide which
commands are supportable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PF supports all debugfs command, but VF only supports part of
debugfs command. So VF should not show unsupported help information.
This patch adds a check for PF and PF to show the supportable help
information.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates VF's TQP statistic info in the service task,
and adds a limitation to prevent update too frequently.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.
The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.
In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allow users to dump content of NCL_CONFIG by using debugfs
command.
Command format:
echo dump ncl_config <offset> <length> > cmd
It will print as follows:
hns3 0000:7d:00.0: offset | data
hns3 0000:7d:00.0: 0x0000 | 0x00000020
hns3 0000:7d:00.0: 0x0004 | 0x00000400
hns3 0000:7d:00.0: 0x0008 | 0x08020401
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for network interface message level
settings. The message level can be changed by module parameter
or ethtool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli