The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is configured with an IP address a router interface (RIF)
should be configured for it in the device. Allow configuration of RIFs
based on IPv6 address notifications as well as IPv4.
Note that the RIF exists as long as an IP address is configured on the
netdev, regardless of the address family.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we can start using IPv6, we need to trap certain control packets
to the CPU. Among others, these include Neighbour Discovery, DHCP and
neighbour misses.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 MLDv1/2 packet trapping.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case local sockets have the IP_ROUTER_ALERT socket option set, then
they expect to get packets with the Router Alert option.
Trap such packets, so that the kernel could inspect them and potentially
send them to interested sockets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1c6c6d221e ("mlxsw: spectrum: Mirror certain packets to
CPU") we marked packets that were mirrored to the CPU, so that they
won't be flooded again by the bridge driver.
However, certain packets are trapped in the device's router block, after
passing through the bridge block where they were potentially flooded.
Mark all packets coming from L3 traps, so that they won't be potentially
flooded again by the bridge driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for access cable info via ethtool.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch made it unnecessary to map ports to modules before we
allocate their struct. We can now therefore pass the port struct to
these functions, thereby making them consistent with other functions
that operate on ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be94535f95 ("mlxsw: spectrum: Make split flow match firmware
requirements") we had to modify the port split flow to overcome quirks
in the device's firmware. This resulted in asymmetrical code with
regards to port creation and removal.
The problem in the firmware is long gone and since we can now enforce a
minimal firmware version, we can simplify the code and make it symmetric
again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FDB add/del are now done through the notification chain. The FDBs
are synced with the bridge and there is no need for extra dumping.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. Support for stacked devices
is also provided. In case of a successful FDB add a notification is
sent back to bridge.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge port attributes/vlan for mlxsw devices should be set only
from bridge code. The vlans are synced totally with the bridge so
there is no need to special dump support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an ACL trap and put it into ip2me trap group.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the firmware file name to be in "mellanox" directory.
This commit is a followup to the linux-firmware commit a4c72696f5f4
("Mellanox: Add firmware for mlxsw_spectrum")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add callback to the ethtool flash_device op. This callback uses the mlxfw
module to flash the new firmware file to the device.
As the firmware flash process takes about 20 seconds and ethtool takes the
rtnl lock during the flash_device callback, release the rtnl lock at the
beginning of the flash process and take it again before leaving the
callback. This way, the rtnl is not held during the process. To make sure
the device does not get deleted during the flash process, take a reference
to it before releasing the rtnl lock.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device supports three types of FIDs. 802.1Q and 802.1D FIDs for
VLAN-aware and VLAN-unaware bridges (respectively) and rFIDs to
transport packets to the router block.
The different users (e.g., bridge, router, ACLs) of the FIDs
infrastructure need not know about the internal FIDs implementation and
can therefore interact with it using a restricted set of exported
functions.
By encapsulating the entire FID logic and hiding it from the rest of the
driver we get a code base that it much simpler and easier to work with
and extend.
For example, in the current Spectrum ASIC only 802.1D FIDs can be
assigned a VNI, but future ASICs will also support 802.1Q FIDs. With
this patch in place, support for future ASICs can be easily added by
implementing a new FID operations according to their capabilities.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the cover letter, since the introduction of the bridge
offload in the mlxsw driver, information related to the offloaded bridge
and bridge ports was stored in the individual port struct,
mlxsw_sp_port.
This lead to a bloated struct storing both physical properties of the
port (e.g., autoneg status) as well as logical properties of an upper
bridge port (e.g., learning, mrouter indication). While this might work
well for simple devices, it proved to be hard to extend when stacked
devices were taken into account and more advanced use-cases (e.g., IGMP
snooping) considered.
This patch removes the excess information from the above struct and
instead stores it in more appropriate structs that represent the bridge
port, the bridge itself and a VLAN configured on the bridge port.
The membership of a port in a bridge is denoted using the Port-VLAN
struct, which points to the bridge port and also member in the bridge
VLAN group of the VLAN it represents. This allows us to completely
remove the vPort abstraction and consolidate many of the code paths
relating to VLAN-aware and unaware bridges.
Note that the FID / vFID code is currently duplicated, but this will
soon go away when the common FID core will be introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used to create FIDs upon the creation of VLAN uppers on
top of the VLAN-aware bridge. This was done so that in case a router
interface (RIF) was configured on top of the bridge, the FID would
already be there.
Instead, simplify the code and only create the FID upon RIF creation.
This is an intermediary step towards the introduction of the common FID
core, in which this code would be completely removed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when port netdevs (or their uppers) are enslaved to a bridge,
we simply propagate the CHANGEUPPER event all the way down and lose the
context of the actual netdevice used as the bridge port.
This leads to a lot of information hanging off the ports (and vPorts),
which doesn't logically belong there, such as mrouter indication and
unknown unicast flood state.
Following patches are going to put the mlxsw_sp_port struct on diet and
instead introduce a bridge port struct, where the above mentioned
information belongs. But in order to do that, we need to be able to
determine the bridge port netdevice, so propagate it down.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to get rid of vPorts completely later in the patchset, but
the router code is self-contained, so it's a good candidate to start the
transition with.
Convert all the functions that expects to operate on a vPort to operate
on a Port-VLAN instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is destroyed, it leaves the FID it's currently mapped to
(if any) and drops the reference. The FID's leave function expects to
get the vPort as its argument, but this will have to change when the
vPort model is retired.
Change the function signature to expect a Port-VLAN struct instead and
patch the call sites accordingly.
The code introduced in this patch will be removed later in the patchset,
but this intermediary step is required in order to ease the code review.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first step in the transition from the vPort model to a
unified Port-VLAN structure. The new structure is defined and created /
destroyed upon invocation of the 8021q ndos, but it's not actually used
throughout the code.
Subsequent patches will initialize it correctly and also create /
destroy it upon switchdev's VLAN object.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently transition the port to "Virtual mode" upon the creation of
its first VLAN upper, as we need to classify incoming packets to a FID
using {Port, VID} and not only the VID.
However, it's more appropriate to transition the port to this mode when
the {Port, VID} are actually mapped to a FID. Either during the
enslavement of the VLAN upper to a VLAN-unaware bridge or the
configuration of a router port.
Do this change now in preparation for the introduction of the FID core,
where this operation will be encapsulated.
To prevent regressions, this patch also explicitly configures an OVS
slave to "Virtual mode". Otherwise, a packet that didn't hit an ACL rule
could be classified to an existing FID based on a global VID-to-FID
mapping, thus not incurring a FID mis-classification, which would
otherwise trap the packet to the CPU to be processed by the OVS daemon.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the spectrum module check the current device firmware version, and if
it is below the supported version, use the libfirmware API to request a
firmware file with the supported firmware version and flash it to the
device using the mlxfw module.
The firmware file names are expected to be of Mellanox Firmware Archive
version 2 (MFA2) format and their name are expected to be in the following
pattern: "mlxsw_spectrum-<major>.<minor>.<sub-minor>.mfa2".
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxfw module defines several needed callbacks in order to flash the
device's firmware. As the mlxfw module is shared between several different
drivers, those callbacks are the glue functionality that is responsible
for hardware interaction. Add those callbacks using the MCQI, MCC, MCDA
registers.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In virtual mode, packets are classified to FIDs based on their ingress
port and VLAN whereas in non-virtual mode only the VLAN is taken into
account.
Currently ports are initialized to use virtual mode due to the presence
of the PVID vPort. However, we're going to transition ports between both
modes based on the FIDs they use and not merely based on the presence on
a VLAN upper. Therefore, during initialization, no mode will be
explicitly set.
Since the Programmer's Reference Manual (PRM) doesn't specify a default,
explicitly set the port to non-virtual mode and later transition the
port between both modes based on the FIDs it uses.
In a follow-up patchset, this step will be moved to the common FID core
where it logically belongs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PVID is a port attribute and should therefore reside in the main driver
file and not the switchdev specific one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer batch VLAN operations, so there's no need to set the
learning state for a range of VLANs.
Use a common function to set the learning state for a Port-VLAN, thereby
making the code saner more receptive for upcoming changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev's VLAN object has the ability to describe a range of VLAN IDs,
but this is only used when VLAN operations are done using the SELF flag,
which is something we would like to remove as it allows one to bypass
the bridge driver.
Do VLAN operations on a per-VLAN basis, thereby simplifying the code and
preparing it for refactoring in a follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some attributes in the global chip struct are only relevant for bridge
operation, so encapsulate them in their own struct that isn't exposed to
non-bridge code.
This will also help us later, when we add more bridge-specific
attributes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is enslaved to a VRF master, its router interface (RIF)
needs to be destroyed (if exists) and a new one created using the
corresponding virtual router (VR).
>From the driver's perspective, the above is equivalent to an inetaddr
event sent for this netdev. Therefore, when a port netdev (or its
uppers) are enslaved to a VRF master, call the same function that
would've been called had a NETDEV_UP was sent for this netdev in the
inetaddr notification chain.
This patch also fixes a bug when a LAG netdev with an existing RIF is
enslaved to a VRF. Before this patch, each LAG port would drop the
reference on the RIF, but would re-join the same one (in the wrong VR)
soon after. With this patch, the corresponding RIF is first destroyed
and a new one is created using the correct VR.
Fixes: 7179eb5acd ("mlxsw: spectrum_router: Add support for VRFs")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no FID set for a specific packet, the HW will drop it.
However, by default these packets are useful to be delivered to CPU as
it can inspect them and program HW accordingly. So add this trap.
This would only ever happen when port is enslaved to an OVS master.
Otherwise, packets would be dropped during VLAN / STP filtering,
before FID classification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From now on, a port can become a slave of OVS master. All vlans
are enabled, STP state is set to "forwarding". It is up to the OVS
userspace daemon to setup the flows either in kernel or in HW using TC
flower offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, mlxsw_sp_port_vlan_set range is limited by
MLXSW_REG_SPVM_REC_MAX_COUNT. In spectrum_switchdev code this is
wrapped up by a helper function which actually does multiple calls
to FW for bigger ranges. Move the code into mlxsw_sp_port_vlan_set
and use it always. That allows caller not to care about the range.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For forwarding using ACL action, HW needs a valid FID to be setup. It
does not actually use it, so it can be any valid FID. So create a dummy
FID only for this purpose.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous patch, the cell size may change in future
devices, so query it from the firmware instead of hard coding it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizes and thresholds of the priority group (PG) buffers are
configured in cells, which represent a specific amount of bytes.
The cell size can vary in different devices, so it's better to query it
from the firmware than hard coding it.
Refactor the code dealing with this value into different functions, so
that it will be easier to make the conversion in the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently hard code the maximum number of ports in the driver, but
this may change in future devices, so query it from the firmware
instead.
Fallback to a maximum of 64 ports in case this number can't be queried.
This should only happen in SwitchX-2 for which this number is correct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the default case for matchall offload with what's there
for flower.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the struct representing router interface "mlxsw_sp_rif"
is reffered as "r" in various places in the driver. Furthermore it
contains a member which specify the index which is called "rif".
This patch change "r" to "rif" and "rif" to "rif_index".
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.
Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.
If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: Arkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.
The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.
Each module can add dedicated sub-pool or use existing one.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inetaddr notification block is currently implemented in the main
driver file, but this isn't really appropriate, as it mainly creates and
destroys router interfaces (RIFs) which belong with the rest of the
router code.
This will become even more apparent later on when we'll need to bind
these RIFs to virtual routers according to the VRF's table.
Structure the driver better and prevent unnecessary function exports by
moving the RIF related code with the rest of the router code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use the RIF reference count to determine when the last IP
address was removed, but instead we can just test 'in_dev->ifa_list'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN device is configured on top of a LAG device (f.e.,
bond0.10), a vPort is created on top of each of the LAG's slaves and its
'dev' pointer is set to the VLAN device.
This is in contrast to the implicit PVID vPort (representing 'bond0'),
whose 'dev' pointer keeps pointing to the port netdev itself (f.e.,
'sw1p1').
Make both cases consistent by setting their 'dev' pointer to the actual
netdev they represent. Either the LAG device itself (in the case of the
PVID vPort) or the VLAN device on top of it.
This will later allow us to more easily understand for which netdev we
should create the router interface (RIF) upon enslavement to a VRF
master.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an upper device is configured on top of a vPort we make sure it's a
bridge master during PRECHANGEUPPER and fail otherwise. Therefore, when
CHANGEUPPER is later received we don't bother checking the upper's type.
Make the code more extendable in preparation for VRF uppers, by checking
the upper's type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to allow bridges stacked on top of port netdevs to be
enslaved to a VRF, but for now, only VLAN uppers of the VLAN-aware
bridge are supported.
Sanitize any other bridge upper. This is consistent with the way we
sanitize port netdevs' uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dd82364c3a ("mlxsw: Flip to the new dev walk API") did some
small changes in mlxsw code, but it did not respect the naming
conventions. So fix this now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Point back the unregister IPv6 mc table to the bc table.
It is done since IPv6 mcast snooping is not supported for Spectrum yet.
Reported-by: Jiri Pirko <jiri@mellanox.com>
Fixes: 71c365bdc4 ("mlxsw: spectrum: Separate bc and mc floods")
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.
Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.
The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the MPSC register, add the functions that configure port-based
packet sampling in hardware and the necessary datatypes in the
mlxsw_sp_port struct. In addition, add the necessary trap for sampled
packets and integrate with matchall offloading to allow offloading of the
sample tc action.
The current offload support is for the tc command:
tc filter add dev <DEV> parent ffff: \
matchall skip_sw \
action sample rate <RATE> group <GROUP> [trunc <SIZE>]
Where only ingress qdiscs are supported, and only a combination of
matchall classifier and sample action will lead to activating hardware
packet sampling.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.
Fix this by adding the original skb release to the main path.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the order of the free directives to match the port init function
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is split we should mark it as such, as otherwise the split
ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit
operation fails:
$ devlink port split sw1p3 count 4
$ devlink port unsplit eth0
devlink answers: Invalid argument
[ 598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split
Fixes: 67963a33b4 ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Reviewed-by: Elad Raz <eladr@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure policers and connect them to trap groups.
While many trap groups share policer's configuration they don't share
the actual policer because each trap group represents a different
flow / protocol and we don't want one of them to be able to exceed its
rate on behalf of another.
For example, if STP and LLDP gets to send 128 packets/sec each, if we
put them in one 256 packets/sec policer, one can send 200 packets while
the other only 50.
Note that IP2ME covers lots of flows, so it's limit is set to match the
cpu ability to handle data.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).
Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.
This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).
This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for BGP protocol that was previously trapped by the generic trap
for IP2ME. This trap will allow us to have better control (over priority
and rate) of the traffic.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.
Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).
Parameters without default value:
TC - the traffic class for packets that hit this trap group.
(old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)
Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
(new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
group id)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the emad trap init was done in the core. In the future we will
want to add some changes to the traps groups, according to device type.
This commit create a driver function to create the trap group for the
emad, so later it can be changed by devices. It also changes the emad
registration to use the new generic functions.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we set the trap group to pre-determined option, based on whether
it is an rx or event trap.
This commit adds a possibility to chose the trap group, so it can be set
to different values in the following patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the old rx listener struct definitions by the generic ones.
Use the new generic registering / unregistering functions for them.
Add some macros to organize the trap list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we no longer rely on flooding traffic to the CPU in
order to trap packets intended for the host itself. Therefore, the FDB
MC trap can be removed.
Remove traps for protocols that are not supported yet.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.
Fix this by initializing the reference count to 1.
Also add a warning to put function.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <generated/utsrelease.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we are about to introduce IB port APIs, we will add prefixes to
existing APIs.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink register/unregister is done directly from
spectrum/switchx2 port create/remove functions. With a need to
introduce a port type change, the devlink port instances have to be
persistent across type changes, therefore across port create/remove
function calls. So do a bit of reshuffling to achieve that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add Infiniband support to PTYS. In order to maintain proper
conventions, we will change pack and unpack prefix to eth.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmentrical with create and do the check outside the remove function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently discovered a bug in the firmware in which a field's length in
one of the registers was incorrectly set. This caused the firmware to
access garbage data that wasn't initialized by the driver and therefore
emit error messages.
While the bug is already fixed and the driver usually zeros the buffers
passed to the firmware, there are a handful of cases where this isn't
done. Zero the buffer in these cases and prevent similar bugs from
recurring, as they tend to be hard to debug.
Fixes: 52581961d8 ("mlxsw: core: Implement fan control using hwmon")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this so the sysfs has "device" link correctly set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, mlxsw_pci.ko is the module that registers PCI table for all
drivers (spectrum and switchx2). That is problematic for example with
dracut. Since mlxsw_spectrum.ko and mlxsw_switchx2.ko are loaded
dynamically from within mlxsw_core.ko, dracut does not have track of
them and avoids them from being included in initramfs.
So make this in an ordinary way and define the PCI tables in individual
driver modules, so it can be properly loaded and included in dracut
initramfs image. As a side effect, this patch could remove no longer
necessary driver "kind" strings which were used to link PCI ids with
individual mlxsw drivers.
Suggested-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of resources is going to get much bigger, ease up the
addition by simly defining IDs. Convert the existing structure members
to a set array, one for validity, one for values. Introduce a set of
getters and setters for easy access.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforce const for getter buf args.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mlxsw users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to specify that the mlxsw spectrum driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an earlier check and return if err is non-zero, so
the check to see if it is zero is redundant in every iteration
of the loop and hence the check can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace max rif const with using the result from resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add max system ports, max regions and max vlan groups to resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resources from resource query to determine values for
the profile configuration.
Add KVD determined section sizes to the resources struct.
Change the profile struct and value to match this changes.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko