Support basic stats for PRIO qdisc, which includes tx packets and bytes
count, drops count and backlog size. The rest of the stats are irrelevant
for this qdisc offload.
Since backlog is not only incremental but reflecting momentary value, in
case of a qdisc that stops being offloaded but is not destroyed, backlog
value needs to be updated about the un-offloading.
For that reason an unoffload function is being added to the ops struct.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading PRIO qdisc as root qdisc.
The support is for up to 8 bands.
Routed packets priority is determined by the DSCP field with the default
translations. Bridged packets priority is determined by the PCP field, if
exist, otherwise it is set to 0.
Since both options have only priorities 0-7, higher priorities mapping are
being ignored.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When routing ip packets, the kernel is setting the SKB's priority
based on the tos field of the packet.
Imitate this behavior in the mlxsw router, having the internal
switch priority of a routed packet determined according to its DS
field.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.
This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit eb789980d0 ("mlxsw: spectrum_router: Populate adjacency
entries according to weights") the driver includes support for
non-equal-cost multipath, but IPv4 nexthops were the only user.
Now that the kernel supports weighted IPv6 nexthops, we can extend the
driver to support it as well.
This is done by assigning each nexthop its configured weight, so that it
will be populated accordingly in the device's adjacency table. The
`weight` parameter is also taken into account when comparing nexthop
groups in order not to consolidate non-identical groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qdisc is being replaced by another qdisc of the same type, it can
simply override over its configuration.
However, if it replaces a qdisc of another type, it needs to be removed
before setting the new qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a generic qdisc replace function.
For that goal, add three functions to the qdisc ops struct:
* check_params: Checks if the given parameters are offloadable.
* replace: Offload the given parameters.
* clean_stats: clean the qdisc stats for the offloaded qdisc.
integrate RED offloading into using the new internal replace API.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a destroy function to the qdiscs ops struct.
Create a generic qdisc destroy function, that clears the qdisc metadata as
well as calling the specific qdisc destroy function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc struct have the Qdisc_class_ops struct.
This patch introduces the similar ops struct for the mlxsw_sp_qdisc_ops
struct. It allows better readability as well as code reusability for the
common parts of some functions like destroy.
The first operations to be added are the statistics getters.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every qdisc op gets the qdisc handle ID as well as its location. Each one
of them, beside replace, checks if the handle doesn't match the qdisc in
the given location, and if so, it returns without running the actual op.
Unite these checks to one comparison function and avoid sending the handle
id to these ops.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tclass number is needed for most of the operations related to the qdisc in
the driver. Create a field for it in the mlxsw_sp_qdisc instead of passing
it to every function as parameter.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability by changing the clean stats function to handle only
RED. Qdiscs that will be offloaded in the future will have a clean stats
function of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean RED offloaded stats and make them more generic by breaking the
generic qdisc stats to a struct of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the value of the xstats requested from the driver for offloaded RED
to be incremental, like the normal stats.
It increases consistency - if a qdisc stops being offloaded its xstats
don't change.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of the stats struct to be generic, so it could be used for
other qdisc offload, that will be added in the next patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the qdisc related data from the spectrum.h to spectrum_qdisc.c.
Create an init and fini functions for the qdiscs.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.
Fixes: 96f17e0776 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.
Wait for 100ms before starting the polling.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the xdp_rxq_info_reg() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 0ddf543226 ("xdp/mlx5: setup xdp_rxq_info")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the arguments net_dim() by formatting them into a struct
net_dim_sample before calling the function.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Suggested-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This move allows drivers to add private structure elements to track the
number of packets, bytes, and interrupts events per ring. A driver
also defines a workqueue handler to act on this collected data once per
poll and modify the coalescing parameters per ring.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all appropriate mlx5_am* and MLX5_AM* references to net_dim and
NET_DIM, respectively, in code that handles dynamic interrupt
moderation. Also change all references from 'am' to 'dim' when used as
local variables and add generic profile references.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions were identified as ones that could be made generic and
used by multiple drivers. Most of the contents of en_rx_am.c are moved
to net_dim.c.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More movement to help make this code more generic.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mlx5e_am_sample more generic so that it can be called easily
from a driver that does not use the same data structure to store these
values in a single structure.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move these to newly created file to prepare to move these functions to a
library.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create new header file to prepare to move code that handles irq
moderation to a library that lives in a header file.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVF5WAAoJEEg/ir3gV/o+fRkH/0PxjwJRA3REqhi/H8HOdH9f
cBLrOzFdqTCYQWQFCLFbMQ/Zgoel3KglpJ0iQMjuVFfjMbybVXOe8FAEVdbWHnfL
C+2HRMe8dplKrsq5UkxJhbyKhFKhl2XeMFYWonw9dSM7Nz5DyowQ1y1r5SgMlMAv
t3mYAIa4kZHK18BjDoIsCoAXXwsHiztR2irMp5+DwataTGP7vC7AsrucDxLA/qFf
I3E15DZk9s1f53PUuY7CYnUnJfMMP3VJdxpyx4k6xt9J2IMuilF4YyD6wpAKsVQU
/LzRkWI9x/6QindffqlrACeeidimOeY4pC4txIhS5uXgFXulugDHq1/Ih1sgZS8=
=g5vr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2018-01-08
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the checks are done in upper layer ethtool code,
checks in driver are not needed any more.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation, any requested RX/TX ring size value
that is less than minimum is silently casted to nearest valid value.
Update this behavior to align with mlx5 behavior by printing warning
in dmesg and remaining the size unchanged.
Kernel is responsible for verifying against the maximum.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get time stamping capabilities using ethtool for
child interface.
Usage example:
ethtool -T CHILD-DEVNAME
This change reuses the functionality of parent devices and does not
introduce any new logic.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support to control precision time protocol on child interfaces
using ioctl.
This commit changes the following:
- Change parent ioctl function to be non static
- Reuse the parent ioctl function in child devices
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current implementation takes the child timestamp object from
the parent since the rq in mlx5i_complete_rx_cqe belongs to the parent.
This change fixes the issue by taking the correct timestamp.
Fixes: 7e7f4780c3 ("net/mlx5e: IPoIB, Use hash-table to map between QPN to child netdev")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We refer to TC NIC rule that involves forwarding as "hairpin".
All hairpin rules from the current NIC device (called "func" in
the code) to a given NIC device ("peer") are steered into the
same hairpin RQ/SQ pair.
The hairpin pair is set on demand and removed when there are no
TC rules that need it.
Here's a TC rule that matches on icmp, does header re-write of the
dst mac and hairpin from RX/enp1s2f1 to TX/enp1s2f2 (enp1s2f1/2 are
two mlx5 devices):
tc filter add dev enp1s2f1 protocol ip parent ffff: prio 2
flower skip_sw ip_proto icmp
action pedit ex munge eth dst set 10:22:33:44:55:66 pipe
action mirred egress redirect dev enp1s2f2
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the code to do basic setup for hairpin object which
will later serve offloading TC flows.
This includes calling the mlx5 core to create/destroy the hairpin
pair object and setting the HW transport objects that will be used
for steering matched flows to go through hairpin.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Low level code to setup hairpin pair core object, deals with:
- create hairpin RQs/SQs
- destroy hairpin RQs/SQs
- modifying hairpin RQs/SQs - pairing (rst2rdy) and unpairing (rdy2rst)
Unlike conventional RQs/SQs, the memory used for the packet and descriptor
buffers is allocated by the firmware and not the driver. The driver sets
the overall data size (log).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the more appropriate netdev_WARN_ONCE instead of WARN_ONCE macro.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-01-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a start of a framework for extending struct xdp_buff without
having the overhead of populating every data at runtime. Idea
is to have a new per-queue struct xdp_rxq_info that holds read
mostly data (currently that is, queue number and a pointer to
the corresponding netdev) which is set up during rxqueue config
time. When a XDP program is invoked, struct xdp_buff holds a
pointer to struct xdp_rxq_info that the BPF program can then
walk. The user facing BPF program that uses struct xdp_md for
context can use these members directly, and the verifier rewrites
context access transparently by walking the xdp_rxq_info and
net_device pointers to load the data, from Jesper.
2) Redo the reporting of offload device information to user space
such that it works in combination with network namespaces. The
latter is reported through a device/inode tuple as similarly
done in other subsystems as well (e.g. perf) in order to identify
the namespace. For this to work, ns_get_path() has been generalized
such that the namespace can be retrieved not only from a specific
task (perf case), but also from a callback where we deduce the
netns (ns_common) from a netdevice. bpftool support using the new
uapi info and extensive test cases for test_offload.py in BPF
selftests have been added as well, from Jakub.
3) Add two bpftool improvements: i) properly report the bpftool
version such that it corresponds to the version from the kernel
source tree. So pick the right linux/version.h from the source
tree instead of the installed one. ii) fix bpftool and also
bpf_jit_disasm build with bintutils >= 2.9. The reason for the
build breakage is that binutils library changed the function
signature to select the disassembler. Given this is needed in
multiple tools, add a proper feature detection to the
tools/build/features infrastructure, from Roman.
4) Implement the BPF syscall command BPF_MAP_GET_NEXT_KEY for the
stacktrace map. It is currently unimplemented, but there are
use cases where user space needs to walk all stacktrace map
entries e.g. for dumping or deleting map entries w/o having to
close and recreate the map. Add BPF selftests along with it,
from Yonghong.
5) Few follow-up cleanups for the bpftool cgroup code: i) rename
the cgroup 'list' command into 'show' as we have it for other
subcommands as well, ii) then alias the 'show' command such that
'list' is accepted which is also common practice in iproute2,
and iii) remove couple of newlines from error messages using
p_err(), from Jakub.
6) Two follow-up cleanups to sockmap code: i) remove the unused
bpf_compute_data_end_sk_skb() function and ii) only build the
sockmap infrastructure when CONFIG_INET is enabled since it's
only aware of TCP sockets at this time, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver have a special drop-RQ queue (one per interface) that
simply drops all incoming traffic. It helps driver keep other HW
objects (flow steering) alive upon down/up operations. It is
temporarily pointed by flow steering objects during the interface
setup, and when interface is down. It lacks many fields that are set
in a regular RQ (for example its state is never switched to
MLX5_RQC_STATE_RDY). (Thanks to Tariq Toukan for explanation).
The XDP RX-queue info for this drop-RQ marked as unused, which
allow us to use the same takedown/free code path as other RX-queues.
Driver hook points for xdp_rxq_info:
* reg : mlx5e_alloc_rq()
* unused: mlx5e_alloc_drop_rq()
* unreg : mlx5e_free_rq()
Tested on actual hardware with samples/bpf program
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The uplink_rpriv variable was added at the start of the function but
only used inside of an #ifdef:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'mlx5e_route_lookup_ipv6':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:1549:25: error: unused variable 'uplink_rpriv' [-Werror=unused-variable]
This moves the declaration into that #ifdef as well.
Fixes: 5ed99fb421 ("net/mlx5e: Move ethernet representors data into separate struct")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that
have uppers") the driver forbids enslavement to netdevs that already
have uppers of their own, as this can result in various ordering
problems.
This requirement proved to be too strict for some users who need to be
able to enslave ports to a bridge that already has uppers. In this case,
we can allow the enslavement if the bridge is already known to us, as
any configuration performed on top of the bridge was already reflected
to the device.
Fixes: 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that have uppers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we remove the neighbour associated with a nexthop we should always
refuse to write the nexthop to the adjacency table. Regardless if it is
already present in the table or not.
Otherwise, we risk dereferencing the NULL pointer that was set instead
of the neighbour.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
- cxgb4 fix for an iser testing failure as debugged by Steve and Sagi.
The problem was a driver bug in the handling of shutting down a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on error
unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IkGi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
Nogah Frankel