Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Pull libata changes from Tejun Heo:
"Nothing too interesting. Only two minor fixes in libata core. Most
changes are specific to hardware which isn't too common"
* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device IDs for Intel Wildcat Point-LP
sata_rcar: Convert to clk_prepare/unprepare
drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
libata: Add some missing command descriptions
sata_highbank: clear whole array in highbank_initialize_phys()
ahci: disabled FBS prior to issuing software reset
libata: Fix display of sata speed
ahci: imx: setup power saving methods
ata_piix: minor typo and a printk fix
ahci: Changing two module params with static and __read_mostly
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
This patch adds the AHCI-mode SATA Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert this code sequence:
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
to use dma_coerce_mask_and_coherent() to avoid bypassing the architecture
check on the DMA mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add some missing command enumerations from the ATA-8 ACS-3 spec into
include/linux/ata.h, and add the corresponding human-readable command
descriptions in libata-eh.c.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code used the wrong parameter to clear tx_atten[]. It
passed the number of elements instead of sizeof() the array to memset.
The other potential issue was that cphy_base[] wasn't cleared. I'm not
sure if that was a real problem or not, but I have cleared it in my
patch.
Instead of using memset(), this patch uses empty initializers as a
cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested with Marvell 88se9125, attached with one port mulitplier(5 ports)
and one disk, we will get following boot log messages if using current
code:
ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier 1.2, 0x1b4b:0x9715 r160, 5 ports, feat 0x1/0x1f
ahci 0000:03:00.0: FBS is enabled
ata8.00: hard resetting link
ata8.00: SATA link down (SStatus 0 SControl 330)
ata8.01: hard resetting link
ata8.01: SATA link down (SStatus 0 SControl 330)
ata8.02: hard resetting link
ata8.02: SATA link down (SStatus 0 SControl 330)
ata8.03: hard resetting link
ata8.03: SATA link up 6.0 Gbps (SStatus 133 SControl 133)
ata8.04: hard resetting link
ata8.04: failed to resume link (SControl 133)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.04: failed to read SCR 1 (Emask=0x40)
ata8.04: failed to read SCR 0 (Emask=0x40)
ata8.03: native sectors (2) is smaller than sectors (976773168)
ata8.03: ATA-8: ST3500413AS, JC4B, max UDMA/133
ata8.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata8.03: configured for UDMA/133
ata8.04: failed to IDENTIFY (I/O error, err_mask=0x100)
ata8.15: hard resetting link
ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: hard resetting link
ata8.15: SATA link up 6.0 Gbps (SStatus 133 SControl 330)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: limiting SATA link speed to 3.0 Gbps
ata8.15: hard resetting link
ata8.15: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
ata8.15: Port Multiplier vendor mismatch '0x1b4b' != '0x133'
ata8.15: PMP revalidation failed (errno=-19)
ata8.15: failed to recover PMP after 5 tries, giving up
ata8.15: Port Multiplier detaching
ata8.03: disabled
ata8.00: disabled
ata8: EH complete
The reason is that current detection code doesn't follow AHCI spec:
First,the port multiplier detection process look like this:
ahci_hardreset(link, class, deadline)
if (class == ATA_DEV_PMP) {
sata_pmp_attach(dev) /* will enable FBS */
sata_pmp_init_links(ap, nr_ports);
ata_for_each_link(link, ap, EDGE) {
sata_std_hardreset(link, class, deadline);
if (link_is_online) /* do soft reset */
ahci_softreset(link, class, deadline);
}
}
But, according to chapter 9.3.9 in AHCI spec: Prior to issuing software
reset, software shall clear PxCMD.ST to '0' and then clear PxFBS.EN to
'0'.
The patch test ok with kernel 3.11.1.
tj: Patch white space contaminated, applied manually with trivial
updates.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
6.0 Gbps link speed was not decoded properly:
speed was reported at 3.0 Gbps only.
Tested: On a machine where libata reports 6.0 Gbps in
/var/log/messages:
ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
Before:
cat /sys/class/ata_link/link1/sata_spd
3.0 Gbps
After:
cat /sys/class/ata_link/link1/sata_spd
6.0 Gbps
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata fixes from Tejun Heo:
"The only interesting bit is ata_eh_qc_retry() update which fixes a
problem where a SG_IO command may fail across suspend/resume cycle
without the command actually being at fault.
Other changes are low level driver specific and fairly low impact"
* 'for-3.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libahci: fix turning on LEDs in ahci_start_port()
libata: make ata_eh_qc_retry() bump scmd->allowed on bogus failures
ahci_platform: use dev_info() instead of printk()
ahci: use dev_info() instead of printk()
pata_isapnp: Don't use invalid I/O ports
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If EM Transmit bit is busy during init ata_msleep() is called. It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.
The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps
At this moment port #5 wasted all its five tries and failed to
initialize. Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.
If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.
tj: updated comment
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In order to save power consumption as much as possible.
* Disable sata phy internal pll reference clock when sysetem enter
into suspend mode, enable it after resume.
* Setup module parameter used to enable imx ahci test power down
mode(PDDQ) or not, when there is no device detected on the port
* minor modifications:
- The format of the copyright is changed, because that the original
one can't pass fsl internal patch reivew without the character
'(c)'.
- Exports ahci_platform_ops and ahci_error_handler().
NOTE:
* The hot-plug can't be supported when PDDQ mode is ever enabled.
* module parameter usage how-to:
- default: enable PDDQ mode when no device detected.
- add "ahci-imx.hotplug=1" into kernel command line if your don't
want to enable PDDQ mode when no device detected on the port.
tj: Slightly updated description and comments.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The patch fixes a printk() being cut in half, some typos
and a change in comments to better reflect the specs.
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
libata EH decrements scmd->retries when the command failed for reasons
unrelated to the command itself so that, for example, commands aborted
due to suspend / resume cycle don't get penalized; however,
decrementing scmd->retries isn't enough for ATA passthrough commands.
Without this fix, ATA passthrough commands are not resend to the
drive, and no error is signalled to the caller because:
- allowed retry count is 1
- ata_eh_qc_complete fill the sense data, so result is valid
- sense data is filled with untouched ATA registers.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Change "raw" printk() call to dev_info() to provide a better
message to userspace so it can properly identify the device
and not just have to guess.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Change "raw" printk() call to dev_info() to provide a better
message to userspace so it can properly identify the device
and not just have to guess.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The test for 2nd I/O port validity is broken (reversed): On devices
with no control port, the driver attempts to use invalid port 0,
resulting in logs full of bad_io_access errors. On devices with
control port, the driver does not use it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
My old @it.uu.se email address is going away, so update relevant
files to point to my @gmail.com address instead. In sata_promise.c
just delete the address, people can get it from MAINTAINERS.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here module parameters ahci_em_messages and devslp_idle_timeout can
be set as static and __read_mostly.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
The endianness attribute on the 'aux' local variable is wrong, and can
lead to wrong endianness on big-endian machines,
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ata_dev_acpi_handle is defined in libata-acpi.c and the only
external user is libata-zpodd.c, which is built when CONFIG_ATA_ACPI
is set, so there is no need to make an empty stub function for
ONFIG_ATA_ACPI case in libata.h. It also causes compile errors due to
acpi_handle is not defined when !CONFIG_ACPI. This patch fixes this
problem by removing the empty stub.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* acpi-pm:
ACPI / PM: Add state information to error message in acpi_device_set_power()
ACPI / PM: Remove redundant power manageable check from acpi_bus_set_power()
ACPI / PM: Use ACPI_STATE_D3_COLD instead of ACPI_STATE_D3 everywhere
ACPI / PM: Make messages in acpi_device_set_power() print device names
ACPI / PM: Only set power states of devices that are power manageable
Some new SSDs support the queued version of the DSM TRIM command.
Let the driver use the new command if supported.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the following ATA opcodes, which are present
in SATA 3.1 and T13 ATA ACS-3:
SEND FPDMA QUEUED
RECEIVE FPDMA QUEUED
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new port flag, ATA_FLAG_FPDMA_AUX, used to indicate
support for transmission of the H2D FIS 'auxiliary' field.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
SATA 3.1 added an "auxiliary" field to the host-to-device FIS.
Populate the host-to-device FIS with the new field via the
taskfile struct.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixing support for the Silicon Image 3826 port multiplier, by applying
to it the same quirks applied to the Silicon Image 3726. Specifically
fixes the repeated timeout/reset process which previously afflicted
the 3726, as described from line 290. Slightly based on notes from:
https://bugzilla.redhat.com/show_bug.cgi?id=890237
Signed-off-by: Terry Suereth <terry.suereth@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Some SGPIO PICs don't follow the standard very well and expect a certain
number of clock cycles or port frames in each SGPIO pattern. Add two
optional parameters in the DTB that can provide the number of extra
clock cycles to be sent before and after SGPIO pattern. Read those
parameters from the DTB and send the extra clock cycles.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some board designs do not drive the SATA transmit lines within the
specification. The ECME can provide override settings, on a per board
basis, to bring the transmit lines within spec. Read those settings
from the DTB and program them in.
At the time of submission, no production hardware requires this patch.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ACTIVITY and ERROR signals were reversed in the original commit.
Fix that so that hard drive activity does not show up on the error
light, and attempts to indicate that the hard drive is failing do
not show up as hard drive activity. This fixes a fairly serious
functional bug in the driver, but failing to apply this patch will
not cause any stability issues on the system.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Added missing __iomem annotation and staticized local symbol
in order to fix the following sparse warnings:
drivers/ata/pata_samsung_cf.c:244:14: warning: symbol 'pata_s3c_data_xfer' was not declared. Should it be static?
drivers/ata/pata_samsung_cf.c:423:20: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_samsung_cf.c:423:20: expected void const volatile [noderef] <asn:2>*addr
drivers/ata/pata_samsung_cf.c:423:20: got void *
drivers/ata/pata_samsung_cf.c:425:9: warning: incorrect type in argument 2 (different address spaces)
drivers/ata/pata_samsung_cf.c:425:9: expected void volatile [noderef] <asn:2>*addr
drivers/ata/pata_samsung_cf.c:425:9: got void *
drivers/ata/pata_samsung_cf.c:448:37: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_samsung_cf.c:448:37: expected void *s3c_ide_regbase
drivers/ata/pata_samsung_cf.c:448:37: got void [noderef] <asn:2>*ide_addr
drivers/ata/pata_samsung_cf.c:463:37: warning: incorrect type in argument 1 (different address spaces)
drivers/ata/pata_samsung_cf.c:463:37: expected void *s3c_ide_regbase
drivers/ata/pata_samsung_cf.c:463:37: got void [noderef] <asn:2>*ide_addr
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/ata/pata_arasan_cf.c:657:6: warning: symbol 'arasan_cf_error_handler' was not declared. Should it be static?
drivers/ata/pata_arasan_cf.c:686:14: warning: symbol 'arasan_cf_qc_issue' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
If CONFIG_HAVE_CLK is not selected, then all the clk API turn out
into no-ops. In other words, there's no need to have the ifdefs.
The only side-effect of this patch is the extra tiny kmalloc,
but that's not enough reason to have such ugly ifdefs all around
the code.
tj: Slightly massaged comment as per Andrew Lunn.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There are several places in the tree where ACPI_STATE_D3 is used
instead of ACPI_STATE_D3_COLD which should be used instead for
clarity. Modify them all to use ACPI_STATE_D3_COLD as appropriate.
[The definition of ACPI_STATE_D3 itself cannot go away at this point
as it is part of ACPICA.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Enable auto loading by udev when pata_imx is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
These forward declarations are no longer needed, and are probably
historical left-over.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not. Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Wolfram Sang