Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell Wifi PCIe modules don't always behave nicely for PCIe power
management when their firmware hasn't been loaded, particularly after
suspending the PCIe link one or more times. When this happens, we might
end up spinning forever in this status-polling tight loop. Let's make
this less tight by adding a timeout and by sleeping a bit in between
reads, as we do with the other similar loops.
This prevents us from hogging a CPU even in such pathological cases, and
allows the FW initialization to just fail gracefully instead.
I chose the same polling parameters as the earlier loop in this
function, and empirically, I found that this loop never makes it more
than about 12 cycles in a sane FW init sequence. I had no official
information on the actual intended latency for this portion of the
download.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_usb_probe() defines and sets bcd_usb but does not use it,
Compiling with W=1 gives the following warning, fix it.
mwifiex/usb.c: In function ‘mwifiex_usb_probe’:
mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable]
The unused variable seems to be present since 4daffe3543 which introduced
mwifiex_usb_probe().
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 92263a841b introduced mwifiex_deaggr_sdio_pkt which initializes
variable pkt_type but does not use it. Compiling with W=1 gives the following
warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’:
mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable]
Fixes: 92263a841b ("mwifiex: add SDIO rx single port aggregation")
Cc: Zhaoyang Liu <liuzy@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_sdio_resume() intializes pm_flag, just like
mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’:
mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable]
sdio_get_host_pm_caps() is just an acessor, so the call to it is safe
to remove. The unused variable seems to be present since
5e6e3a92b9 which introduced mwifiex_sdio_resume().
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 3935ccc14d introduced mwifiex_tm_cmd() which initializes
struct mwifiex_adapter* adapter, but doesn't use it.
Compiling with W=1 gives the following warning, fix it.
mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’:
mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable]
Fixes: 3935ccc14d ("mwifiex: add cfg80211 testmode support")
Cc: Xinming Hu <huxm@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 429d90d221 introduced mwifiex_cmd_tdls_oper() which initializes
struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’:
mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable]
Fixes: 429d90d221 ("mwifiex: add cfg80211 tdls_oper handler support")
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b5413e6b22 removed all uses of chan_num in mwifiex_config_scan().
Compiling mwifiex with W=1 gives the following warning, fix it.
mwifiex/scan.c: In function ‘mwifiex_config_scan’:
mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable]
Fixes: b5413e6b22 ("mwifiex: increase the number of nodes in command pool")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit bec568ff51 removed the last remaining usage of struct
mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to
mwifiex_del_virtual_intf().
Compiling mwifiex/ with W=1 gives the following warning, fix it.
mwifiex/main.c: In function ‘mwifiex_fw_dpc’:
mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
Fixes: bec568ff51 ("mwifiex: failure path handling in mwifiex_add_virtual_intf()")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We will read fw_cap_info filled by firmware to check whether to
skip ADHOC related commands or not. Also, IBSS_COALESCING_STATUS
command has been moved from init path to adhoc network creation
path.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't want to leave the wake IRQ enabled.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It should never be NULL here, and to think otherwise makes things
confusing.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are never NULL, so stop making people think they might be.
I don't change this for SDIO because SDIO has a racy card-reset handler
that reallocates this struct. I'd rather not touch that mess right now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_func is retrieved via container_of() and should never be NULL.
Checking for NULL just makes the logic more confusing than necessary.
Stop doing that.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO and PCIe drivers handle this. Let's imitate it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
card->adapter gets initialized in mwifiex_register_dev(). As it's not
cleared in mwifiex_unregister_dev(), we may end up accessing the memory
which is already free in below scenario.
Scenario: Driver initialization is failed due to incorrect firmware or
some other reason. Meanwhile device reboot/unload occurs.
This is safe, now that we've properly synchronized suspend() and
remove() with the FW initialization thread; now that code can simply
check for 'card->adapter == NULL' and exit safely.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device core will not allow suspend() to race with remove().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
to_pci_dev() would just do struct offset arithmetic on struct
device to get 'pdev' pointer. We never get NULL pdev pointer.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's possible for the FW init sequence to fail, which will trigger a
device cleanup sequence in mwifiex_fw_dpc(). This sequence can race with
device suspend() or remove() (e.g., reboot or unbind), and can trigger
use-after-free issues. Currently, this driver attempts (poorly) to
synchronize remove() using a semaphore, but it doesn't protect some of
the critical sections properly. Particularly, we grab a pointer to the
adapter struct (card->adapter) without checking if it's being freed or
not. We later do a NULL check on the adapter, but that doesn't work if
the adapter was freed.
Also note that the PCIe interface driver doesn't ever set card->adapter
to NULL, so even if we get the synchronization right, we still might try
to redo the cleanup in ->remove(), even if the FW init failure sequence
already did it.
This patch replaces the static semaphore with a per-device completion
struct, and uses that completion to synchronize the remove() thread with
the mwifiex_fw_dpc(). A future patch will utilize this completion to
synchronize the suspend() thread as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save handshake with firmware might be blocked by on-going
data transfer.
this patch check the PS status in main process and complete
previous blocked PS handshake.
this patch also remove redudant check before call
mwifiex_check_ps_cond function.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We may get SLEEP event from firmware even if TXDone interrupt
for last Tx packet is still pending. In this case, we may
end up accessing PCIe memory for handling TXDone after power
save handshake is completed. This causes kernel crash with
external abort.
This patch will only allow downloading sleep confirm
when no tx done interrupt is pending in the hardware.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit ce4f6f0c35 ("mwifiex: add platform specific wakeup interrupt
support") added WoWLAN feature only for sdio. This patch moves that
code to the common module so that all the interface drivers can use
it for free. It enables pcie and sdio for its use currently.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce function mwifiex_probe_of() to parse common properties.
Interface drivers get to decide whether or not the device tree node
was a valid one (depending on the compatible property),
Lets fill "adapter->dt_node" in mwifiex_add_card().
The function mwifiex_probe_of() is currently only a place holder with
the next patch adding content to it.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Today all the interface drivers (usb/pcie/sdio) assign the
adapter->dev in the register_dev() callback, although they
have this piece of info well before hand.
This patch makes the device structure available for mwifiex
right at the beginning, so that it can be used for early
initialization if needed.
This is needed for subsequent patches in this patchset that
intend to unify and consolidate some of the code that would
otherwise have to be duplicated among the interface drivers
(sdio, pcie, usb).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cleanup_if() callback is the inverse of init_if(). We allocate our
'card' interface structure in the probe() function, but we free it in
cleanup_if(). That gives a few problems:
(a) we leak this memory if probe() fails before we reach init_if()
(b) we can't safely utilize 'card' after cleanup_if() -- namely, in
remove() or suspend(), both of which might race with the cleanup
paths in our asynchronous FW initialization path
Solution: just use devm_kzalloc(), which will free this structure
properly when the device is removed -- and drop the set_drvdata(...,
NULL), since the driver core does this for us. This also removes the
temptation to use drvdata == NULL as a hack for checking if the device
has been "cleaned up."
I *do* leave the set_drvdata(..., NULL) for the hacky SDIO
mwifiex_recreate_adapter(), since the device core won't be able to clear
that one for us.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may reject calibration data from host for certain OTP
settings. In that case, we should continue initialisation ignoring
the failure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds power save parameters(hs_wake_interval and
hs_inactivity_timeout) in host sleep cfg cmd.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SSIDs aren't guaranteed to be 0-terminated. Let's cap the max length
when we print them out.
This can be easily noticed by connecting to a network with a 32-octet
SSID:
[ 3903.502925] mwifiex_pcie 0000:01:00.0: info: trying to associate to
'0123456789abcdef0123456789abcdef <uninitialized mem>' bssid
xx:xx:xx:xx:xx:xx
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: <stable@vger.kernel.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register the WLAN device as a wakeup source since it can
wake the system via wake-on-wireless-lan. In an actual wowlan
event, notify the PM core that we are the current wakeup source.
This allows the PM core to update the wakeup attributes in /sys.
This was causing wakeup issues on chromeos as the system was
apparently confused about the wakeup source.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Eric Caruso <ejcaruso@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the missing destroy_workqueue() before return from
mwifiex_add_virtual_intf() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell p2p device disappears from the list of p2p peers on the other
p2p device after disconnection.
It happens due to a bug in driver. When interface is changed from p2p
to station, certain variables(bss_type, bss_role etc.) aren't correctly
updated. This patch corrects them to fix the issue.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that if single tid 6 packet comes among with massive tid 0
packets, tid 6 packet may stay in it's queue and will never be
transmited. This is because wmm.highest_queued_prio will be set to 2
during transmission of tid 0 packets As a result, main work thread
keeps on looping without serving that packet. In this case, if command
has downloaded to firmware, driver doesn't process it's response causing
command timeout.
This patch will reset highest_queued_prio if packets exist in data
queue, and try to find a ra_list for current private.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wmm.tx_pkts_queued and ralist's total_pkt_count should be updated in
synchronization. They were not correctly updated in
mwifiex_send_processed_packet().
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for this debugfs command is available in driver. This patch
adds usage information in README file.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While copying the vendor_ie obtained from the cfg80211_find_vendor_ie()
to the struct mwifiex_types_wmm_info, length/size was inappropriate.
This patch corrects the required length needed to the
mwifiex_types_wmm_info
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At couple of places in cleanup path, we are just going through the
skb queue and freeing them without unlinking. This leads to a crash
when other thread tries to do skb_dequeue() and use already freed node.
The problem is freed by unlinking skb before freeing it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When host_sleep_config command fails, we should return an error to
PCIe, instead of continuing (and possibly panicking, when we try to keep
processing a timed-out ioctl after we return "successfully" from
suspend).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following is mwifiex driver-firmware host sleep handshake.
It involves three threads. suspend handler, interrupt handler, interrupt
processing in main work queue.
1) Enter suspend handler
2) Download HS_CFG command
3) Response from firmware for HS_CFG
4) Suspend thread waits until handshake completes(i.e hs_activate becomes
true)
5) SLEEP from firmware
6) SLEEP confirm downloaded to firmware.
7) SLEEP confirm response from firmware
8) Driver processes SLEEP confirm response and set hs_activate to wake up
suspend thread
9) Exit suspend handler
10) Read sleep cookie in loop and wait until it indicates firmware is
sleep.
11) After processing SLEEP confirm response, we are at the end of interrupt
processing routine. Recheck if there are interrupts received while we were
processing them.
During suspend-resume stress test, it's been observed that we may end up
acessing PCIe hardware(in 10 and 11) when PCIe bus is closed which leads
to a kernel crash.
This patch solves the problem with below changes.
a) action 10 above can be done before 8
b) Skip 11 if hs_activated is true. SLEEP confirm response
is the last interrupt from firmware. No need to recheck for
pending interrupts.
c) Add flush_workqueue() in suspend handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch helps get rid of goto statement and improves readability.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller