Fixes the following W=1 kernel build warning(s):
drivers/ptp/ptp_clockmatrix.c:1408: warning: Cannot understand * @brief Maximum absolute value for write phase offset in picoseconds
drivers/ptp/ptp_clockmatrix.c:1408: warning: Cannot understand * @brief Maximum absolute value for write phase offset in picoseconds
drivers/ptp/ptp_clockmatrix.c:1408: warning: Cannot understand * @brief Maximum absolute value for write phase offset in picoseconds
drivers/ptp/ptp_clockmatrix.c:1408: warning: Cannot understand * @brief Maximum absolute value for write phase offset in picoseconds
drivers/ptp/ptp_clockmatrix.c:1408: warning: Cannot understand * @brief Maximum absolute value for write phase offset in picoseconds
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: IDT-support-1588@lm.renesas.com
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code clean-up.
* Remove blank line between variable declarations.
* Remove blank line between:
err = blah(...)
if (err)
...
* Remove unnecessary blank line before/after loop constructs.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code clean-up.
* Remove unnecessary \n termination from dev_*() messages.
* Remove 'char *fmt' to define strings to stay within 80 column
limit. Not needed since coding guidelines increased to
100 columns limit.
Keeping format in place allows static code checkers to
validate the arguments.
* Tighten up vertical spacing.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling output using PTP_CLK_REQ_PEROUT, need to align the output
clock to the internal 1 PPS clock.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the device initialization aligns the rising edge of the output
clock to the internal 1 PPS clock. If the system APLL and DPLL is not
locked, then the alignment will fail and there will be a fixed offset
between the internal 1 PPS clock and the output clock.
After loading the device firmware, poll the system APLL and DPLL for
locked state prior to initialization, timing out after 2 seconds.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SM_RESET device only when loading full configuration and check
for BOOT_STATUS. Also remove polling for write trigger done in
_idtcm_settime().
Changes since v1:
-Correct warnings from strict checkpatch
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/1607442117-13661-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Feed kstrtou8 with NULL terminated string.
Changes since v1:
-Use sscanf to get rid of adhoc string parse.
Changes since v2:
-Check if sscanf returns 3.
Fixes: 7ea5fda2b1 ("ptp: ptp_clockmatrix: update to support 4.8.7 firmware")
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1606273115-25792-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The old code for i2c write would break on some controllers, which fails
at handling Repeated Start Condition. So we will just use i2c_master_send
to handle write in one transanction.
Changes since v1:
- Remove indentation change
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 4.8.7 firmware, adjtime can change delta instead of absolute time,
which greately increases snap accuracy. PPS alignment doesn't have to
be set for every single TOD change. Other minor changes includes:
adding more debug logs, increasing snap accuracy for pre 4.8.7 firmware
and supporting new tcs2bin format.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add idtcm_adjphase() to support PHC write phase mode.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of loaddr is u8 which is always '<=' 0xff, so the
loaddr <= 0xff is always true, we can remove this comparison.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and fix the version information displayed by the driver.
The new info better relects what is needed to support the hardware.
Prev:
Version: 4.8.0, Pipeline 22169 0x4001, Rev 0, Bond 5, CSR 311, IRQ 2
New:
Version: 4.8.0, Id: 0x4001 Hw Rev: 5 OTP Config Select: 15
- Remove pipeline, CSR and IRQ because version x.y.z already incorporates
this information.
- Remove bond number because it is not used.
- Remove rev number because register was not implemented, always 0
- Add HW Rev ID register to replace rev number
- Add OTP config select to show the user configuration chosen by
the configurable GPIO pins on start-up
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idtcm_caps structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function idtcm_probe()
in the error handling case.
Fixes: 3a6ba7dc77 ("ptp: Add a ptp clock driver for IDT ClockMatrix.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IDT ClockMatrix (TM) family includes integrated devices that provide
eight PLL channels. Each PLL channel can be independently configured as a
frequency synthesizer, jitter attenuator, digitally controlled
oscillator (DCO), or a digital phase lock loop (DPLL). Typically
these devices are used as timing references and clock sources for PTP
applications. This patch adds support for the device.
Co-developed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lee Jones