when nand_get_flash_type() is called, it will read 8 bytes of ID instead of 5,
but the driver only read 5 bytes, so kernel will dump error messages like:
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
fsl-lbc ffe124000.localbus: read_byte beyond end of buffer
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch should fix the following problem:
1. the jffs2-image update in the u-boot was ok
2. first restart and first mount of the NAND-flash-partition was also ok
3. before the restart of controller there are no any activity on NAND-flash except of the jffs2_gcd_mtdX-process ...
4. BUT after the second restart the NAND-flash-partition could not be really used after the second mount,
dmesg filled with messages:
...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03ce0000: 0xc0ff instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x03d00000: 0xc0ff instead
....
Just for for info:
the behaviour observed on mpc8313-based board with the large-page NAND.
The only activity on NAND-flash was the garbage collector process, that looks for CLEANMARKER-nodes
As Scott said it was broken by commit 3ab8f2a2e7
Signed-off-by: Sergej Stepanov <Sergej.Stepanov@ids.de>
--
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.
For former nand driver, it had the two functions:
1. detecting nand flash partitions;
2. registering elbc interrupt.
Now, second function is removed to fsl_lbc.c.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We want error information even if the kernel hasn't been built for verbose
debugging.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the program and erase sequences do not wait for completion,
instead relying on a subsequent waitfunc() callback. However, this causes
the chipselect to be deasserted while the NAND chip is still asserting the
busy pin, which can corrupt activity on other chipselects.
This patch switches to using the sequences recommended by the manual,
in which a wait is performed within the initial command sequence. We can
now re-use the status byte from the initial command sequence, rather than
having to do another status read in the waitfunc.
Since we're already touching the command sequences, it also cleans up some
cruft in SEQIN that isn't needed since we cannot program partial pages
outside of OOB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reported-by: Suchit Lepcha <suchit.lepcha@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When a NAND operation is in progress, all other localbus operations
(including NOR flash) will have to wait for access to the bus. However, the
NAND operation may take longer to complete than the default timeout. Thus,
if NOR is accessed while a NAND operation is in progress, the NAND operation
will fail.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular
Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices
Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader,
can avoid the image written by bootloader cannot read out by kernel.
But the limitation of doing it this way is that, it could break large page
NAND if it is written with NAND disabled in u-boot and read with NAND
enabled, or vice versa.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/fsl_elbc_nand.c:890: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Shaohui Xie