While it is useful to build all of the CCU drivers at once, only 1-3 of
them will be loaded at a time, or possibly none of them if the kernel is
booted on a non-sunxi platform. These CCU drivers are relatively large;
32-bit drivers have 30-50k of data each, while the 64-bit ones are
50-75k due to the increased pointer overhead. About half of that data
comes from relocations. Let's allow the user to build these drivers as
modules so only the necessary data is loaded.
As a first step, convert the CCUs that are already platform drivers.
When the drivers are built as modules, normally the file name becomes
the module name. However, the current file names are inconsistent with
the <platform>-<peripheral> name used everywhere else: the devicetree
bindings, the platform driver names, and the Kconfig symbols. Use
Makfile logic to rename the modules so they follow the usual pattern.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211119033338.25486-3-samuel@sholland.org
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085213.4662-1-caihuoqing@baidu.com
The CCU drivers are not really designed to be unbound. Unbinding a SoC's
main CCU is especially pointless, as very few of the peripherals on the
SoC will work without it. Let's avoid any potential problems by removing
the bind/unbind attributes from sysfs for these drivers.
This change is not applied to the "secondary" CCUs (DE, USB) as those
could reasonably be unbound without making the system useless.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210901050526.45673-3-samuel@sholland.org
Currently, unbinding a CCU driver unmaps the device's MMIO region, while
leaving its clocks/resets and their providers registered. This can cause
a page fault later when some clock operation tries to perform MMIO. Fix
this by separating the CCU initialization from the memory allocation,
and then using a devres callback to unregister the clocks and resets.
This also fixes a memory leak of the `struct ccu_reset`, and uses the
correct owner (the specific platform driver) for the clocks and resets.
Early OF clock providers are never unregistered, and limited error
handling is possible, so they are mostly unchanged. The error reporting
is made more consistent by moving the message inside of_sunxi_ccu_probe.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210901050526.45673-2-samuel@sholland.org
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner's BSP for the A83T lists pll-video0 as the first parent to
csi-mclk with index 0. This parent is not listed in the datasheet, but
actually works, and makes more sense considering the index is the
default value out of reset.
Add pll-video0 as a parent to csi-mclk with index 0.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
It may happen that clock framework finds optimal video PLL rate above
that which is really supported by HW.
User manual doesn't really say what is upper limit for video PLLs on
A83T. Because of that, use the maximum rate defined in BSP clk driver
which is 3 GHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
TCON1 also has M divider, contrary to TCON0. And the mux is only
2 bits wide, instead of 3.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[wens@csie.org: Add description about mux width difference]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. This patch copies the
parameters for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A83T, the audio PLL should have its div1 set to 0, or /1, and
div2 set to 1, or /2. This setting is the default, and is required
to match the sigma-delta modulation parameters from the BSP kernel.
This patch adds a /2 fixed post divider to the audio PLL, and fixes
the enforced d1 & d2 values. This also resolves the mismatch between
the values mentioned in the comment for the audio PLL, and the actual
enforced values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c1 and i2c2 bits for CCU are not bit 0 but bit 1 and bit 2.
Because of that, the i2c0 (bit 0) was not correctly configured.
Fixed the correct bits for i2c1 and i2c2.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Datasheet specified that parent MUX settings are at bits [10:8],
but current implementation specifies incorrect offset at [10:12].
Fix this.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MMC2 clock supports a new timing mode. When the new mode is active,
the output clock rate is halved.
This patch sets the feature flag for the new timing mode, and adds
a pre-divider based on the mode bit.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The divider of the audio PLL has an offset of 1.
Fix this in the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The offset for the PLL lock status register was incorrectly set to
0x208, which actually points to an unused register. The correct
register offset is 0x20c.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T clock control unit is a hybrid of some new style clock designs
from the A80, and old style layout from the other Allwinner SoCs.
Like the A80, the SoC does not have a low speed 32.768 kHz oscillator.
Unlike the A80, there is no clock input either. The only low speed clock
available is the internal oscillator which runs at around 16 MHz,
divided by 512, yielding a low speed clock around 31.250 kHz.
Also, the MMC2 module clock supports switching to a "new timing" mode.
This mode divides the clock output by half, and disables the CCU based
clock delays. The MMC controller must be configure to the same mode,
and then use its internal clock delays.
This driver does not support runtime switching of the timing modes.
Instead, the new timing mode is enforced at probe time. Consumers can
check which mode is active by trying to get the current phase delay
of the MMC2 phase clocks, which will return -ENOTSUPP if the new
timing mode is active.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Samuel Holland