The 8250_fintek.c is support the Fintek F81866/F81216 with dynamic clock.
But It'll generate "division by zero" exception and crash in
fintek_8250_set_termios() with baud rate 0 on baudrate_table[i] % baud.
It can be tested with following C code:
...
struct termios options;
tcgetattr(fd, &options);
...
options.c_cflag = CS8 | CREAD; /* baud rate 0 */
tcsetattr(fd, TCSANOW, &options);
tcflush(fd, TCIOFLUSH);
Fixes: 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Reported-by: Lukas Redlinger <rel+kernel@agilox.net>
Cc: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the datasheet, only the first port supports delay before
send and delay after send.
Reported-by: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware does not support having the same RTS level during RX and TX
when RS485 mode is on (URA in Fintek terminology).
The manufacturer has also confirmed that the delays are not enabled if
the RS485 mode is not enabled.
Therefore we should return -EINVAL if the user wants to have the same
value for RTS_ON_SEND and RTS_AFTER_SEND.
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4d ("serial: Add support for Fintek F81216A LPC to 4 UART")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SuperIO will be configured at boot time by BIOS, but some BIOS
will not deactivate the SuperIO when the end of configuration. It'll
lead to mismatch for pdata->base_port in probe_setup_port(). So we'll
deactivate all SuperIO before activate special base_port in
fintek_8250_enter_key().
Tested on iBASE MI802.
Cc: stable@vger.kernel.org
Tested-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Reviewd-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is fix the warning reported by smatch as following:
drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.
We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 supports baud rates higher than 115200 but needs to raise
it's clock speed from 1.84 to 14.76 MHz.
This is eight times faster, so gives 921600 as resulting baud_base.
F81866 clock register 0xf2:
Bit 7-2 reserved
Bit 1-0 00: 1.8432MHz
01: 18.432MHz
10: 24MHz
11: 14.769MHz
Signed-off-by: Lukas Redlinger <rel+kernel@agilox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs
likes F81866. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81865 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
Level/Low: IRQ_MODE0:0
Edge/High: IRQ_MODE0:1
The following list is brief descriptions of F81865:
F81865 (0704)
9Bit(not implements with mainline)
RS485(implemented)
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs
likes F81216H. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81866 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
The following list is brief descriptions of F81866:
F81866 (1010)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H
The following list is brief descriptions of F81216 series:
F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)
F81216 (0208)
basically 16550A
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated
as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger
level multiplier as 4x when F81216H detected.
Default 16550A trigger level is 8Bytes. When this patch applied, the
trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX
incoming interrupts.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set IRQ Mode when port probed in probe_setup_port()
It should hold the IO port premission via fintek_8250_enter_key() and
release via fintek_8250_exit_key() when we configure the SuperIO.
This patch will move all SuperIO configure operations to
probe_setup_port() to reduce fintek_8250_enter_key() and
fintek_8250_exit_key() usage.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we need to access SuperIO registers, It should write register offset
to base_addr and read/write value to base_addr + 1 to perform read/write.
We can make it more simply with write/read functions.
This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to
reduce SuperIO register operation with lot of outb()/inb().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the fintek driver required defining some macros, but
one of them clashes with a system header on ARM:
drivers/tty/serial/8250/8250_fintek.c:34:0: error: "IRQ_MODE" redefined [-Werror]
#define IRQ_MODE 0x70
In file included from /git/arm-soc/arch/arm/include/asm/ptrace.h:13:0,
from /git/arm-soc/arch/arm/include/asm/irqflags.h:6,
from /git/arm-soc/include/linux/irqflags.h:15,
from /git/arm-soc/arch/arm/include/asm/bitops.h:27,
from /git/arm-soc/include/linux/bitops.h:36,
from /git/arm-soc/include/linux/kernel.h:10,
from /git/arm-soc/include/linux/list.h:8,
from /git/arm-soc/include/linux/module.h:9,
from /git/arm-soc/drivers/tty/serial/8250/8250_fintek.c:11:
arch/arm/include/uapi/asm/ptrace.h:55:0: note: this is the location of the previous definition
This renames the newly introduced 'IRQ_MODE' macro to FINTEK_IRQ_MODE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4da22f1418 ("serial: 8250_fintek: fix the mismatched IRQ mode")
Link: https://patchwork.kernel.org/patch/9200119/
Acked-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some chips with the same interface but different chip ip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the port index and the line id in a private structure.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to remove the handler for rs485 ioctls on serial_8250, all the
drivers must use the implementation on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch lets you set the RS485 cappabilites of the device through
TIOCSRS485 and TIOCGRS485 as defined on Documentation/serial/serial-rs485.txt
In order to probe the device, the PNP id and the device id is used.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ji-Ze Hong (Peter Hong)