The GPIO bit that enables analog output on the Xonar HDAV1.3 also
disables the HDMI audio output, so we better add a switch for it.
Hopefully, this is sufficient to make the HDMI output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the configuration of some unknown GPIO output bits (that
might not be used at all) to be the same as in the Windows driver, just
to be sure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow disabling period wakeup interrupts for all PCM streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the TempoTec/MediaTek HiFier Serenade sound card.
The PCI ID was already there, but the driver handled it like the
Fantasia model, which resulted in a dummy recording device. As
a stereo output-only card, this model is to be handled exactly
like the HG2PCI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort the PCI IDs so that they make logical sense. Also move the card
name comments into this list because the model symbols should be (more)
self-explanationary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Kuroutoshikou CMI8787-HG2PCI sound card.
[replaced non-latin letters in the patch by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd-hifier driver contains more duplicated code than model-specific
code, so it does not make sense for it to be a separate driver.
Handling the two-channel output restriction can be easily done in the
generic driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This board has a strange PCI SSID 13f6:ffff. Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the PEX8111 bridge on the PCI Express cards so that the audio
DMA controller can do proper burst reads and is less likely to lose
data. This is usually done automatically, but is required on older
cards where the user has not applied the PLX firmware update.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCIe/PCI bridge initialization code to configure only the
bridge that is actually connected to the sound chip, instead of any
bridge found in the system. The new code also makes it easier to add
other bridges.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt counter is independent of the buffer counter, so there are
no restrictions on the period size. Having fewer periods also makes
PulseAudio happy.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The input monitor half volume bit results in a factor of 0.5, so the
minimum scale value should be -6 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the symbol for the XCID pins, fix up a decimal/hex confusion for
the CMI8787 package ID, and add the other known package IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The anti-pop delay for the STX should be 800 ms, not 100 ms like the ST.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI ID for the Xonar HDAV1.3 Slim. There is no actual support,
but the presence of the ID allows the EEPROM repair code to work for
this card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller on the Xonar DS is labeled "AV66", not "AV200".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the HT-Omega Claro halo card, the ADC data must be captured from the
second I2S input. Using the default first input, which isn't connected
to anything, would result in silence.
Signed-off-by: Erik J. Staab <ejs@insightbb.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the possibility to route a mix of the two channels of stereo data to
the center and LFE outputs. Due to a WM8766 restriction, all surround
and back channels also get the mixed L/R signal in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Automatically mute the speaker outputs as long as a headphone is plugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the polarity of the headphone detection pin is known, replace
the debugging message with a proper jack plug input device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the correct number, register bits, and names for the input switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for the volume update latch bit was accidentally in the wrong
function, where it would prevent the MSB from being written, instead of
correctly ignoring it for cached values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Line and Mic inputs cannot be used at the same time, so the driver
has to automatically disable one of them if both are set. However, it
forgot to notify userspace about this change, so the mixer state would
be inconsistent. To fix this, check if the other control gets muted,
and send a notification event in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Nathan Schagen
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the WM8776 chip, this driver uses a different sample format and
more features than the Windows driver. When rebooting from Linux into
Windows, the latter driver does not reset the chip but assumes all its
registers have their default settings, so we get garbled sound or, if
the output happened to be muted before rebooting, no sound.
To make that driver happy, hook our driver's cleanup function into the
shutdown notifier and ensure that the chip gets reset.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Nathan Schagen
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 65c3ac885c in 2.6.33 accidentally
left out the initialization of the AC97 codec FMIC2MIC bit, which broke
recording from the front panel microphone.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
In the original code the condition was always true (hopefully) because
WM8776_HPLVOL is zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Insert "Playback" into the input monitor control names to prevent
alsa-lib from treating these controls as global controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a control that allows disabling the high-pass filter of the WM8785 ADC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a control to select between sharp and slow roll-of filter responses
of the DACs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a control to increase the oversampling factor to 128x on cards with
PCM1796 or PCM1792A DACs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a callback that allows model drivers to modify the default I2S MCLK
rate.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control to adjust the headphone amplifier output for
headphones with different impedances.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep a cache of codec registers to avoid unnecessary writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the possibility to route a mix of the two channels of stereo data to
the center and LFE outputs. This is implemented only for models where
the DACs support this, i.e., for the Xonar D1 and DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On card models with two-channel outputs, the base driver can
automatically disable the upmixing control so that the model
drivers do not need to do this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Essence ST uses the CS2000 chip to generate the DAC master clock, so
we better initialize and program it appropriately.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The virtuoso.c file has become rather big. This patch splits it up so
that only code for very similar card models is in one file.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the card is used with a Pericom PI7C9X110 PCI-E/PCI bridge,
reconfigure the latter's PCI buffering to fix an unknown problem.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On cards where the EEPROM was deliberately omitted, we do not need to
try to restore the EEPROM's contents.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the volume is changed continuously (e.g., when the user drags a
volume slider with the mouse), the driver does lots of I2C writes.
Apparently, the sound chip can get confused when we poll the I2C status
register too much, and fails to complete a read from it. On the PCI-E
models, the PCI-E/PCI bridge gets upset by this and generates a machine
check exception.
To avoid this, this patch replaces the polling with an unconditional
wait that is guaranteed to be long enough.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Johann Messner <johann.messner at jku.at>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The card model detection code introduced in 2.6.30 that tries to work
around partially broken EEPROM contents by reading the EEPROM directly
does not handle cards where the EEPROM has been omitted. In this case,
we have to use the default ID to allow the driver to load.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not forget to program the MCLK ratio for the I2S output.
Otherwise, the master clock frequency can be too high for
the DACs at sample frequencies above 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When resuming, we better take the DACs out of the reset state before
trying to use them.
Reference: kernel bug #13599http://bugzilla.kernel.org/show_bug.cgi?id=13599
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone input and its volume register have only one channel, so
we have to make the corresponding mixer control a mono control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar Essence ST and its daughterboard.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar HDAV1.3 has a digital input jack, so enable the corresponding
device.
This is not related to the HDMI stuff, which stays unsupported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add another PCI ID for a second revision of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a PCM stream is closed, flush the corresponding DMA channel.
Otherwise, the DMA controller would continue to output the last sample
which would result in a DC offset on the output.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the HT-Omega Claro (halo) sound cards, the headphone amplifier must
be enabled explicitly by setting a GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Model drivers assume that model_data is zeroed, so we better use
kzalloc() (like we did before when it was allocated together with the
card structure).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use -60 dB as the minimum value of the master volume mixer control.
While the DACs would support ranges down to about -120 dB, such
attenuations are not useful in practice.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HT-Omega Claro halo's ADC is an AK5385 instead of a WM8785, so we
should handle the ADC parameters as we do with the X-Meridian.
Using the code for the wrong ADC does not seem to have any audible
effects, and the Windows driver does it, but it is nonetheless a good
idea to run the AK5385 with an oversampling ratio that is not outside
the documented limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the EEPROM was partially overwritten (which seems to happen before the OS is
booted), restore its entire contents by deducing it from the remaining
information.
This does not have any effect on the Linux driver, which works even with
incomplete information in the EEPROM, but it makes other drivers work again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten. When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers. Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.
Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter. The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When allocating resources, use a fixed name instead of reading it from
the model structure. This allows us to allocate the resources before
the actual model is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the model-specific data dynamically instead of including it in
the memory block of the card structure. This will allow us to determine
the actual model after the card creation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model. Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 7e86c0e685 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.
More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect. In other words, the presence of this
driver does not have any effect on the occurrence of the error. (So
far, the available evidence seems to point to a BIOS bug.)
Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.
The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This hardware has a better chance of working correctly if we don't
forget to enable it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Asus Xonar D2 and D2X models, the SPI chip select signal for the
fourth DAC shares its pin with the serial clock for the EEPROM that
contains the PCI subdevice ID values. It appears that when DAC
registers are written and some other unknown conditions occur (probably
noise on the EEPROM's chip select line), the EEPROM gets overwritten
with garbage, which makes it impossible to properly detect the card
later.
Therefore, we better avoid DAC register writes and make sure that the
driver works with the DAC's registers' default values. Consequently,
the sample format is now I2S instead of left-justified (no user-visible
change), and the DAC's volume/mute registers cannot be used anymore
(volume changes are now done by the software volume plugin).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After sending a reset command to the UART, wait some time for the ACK to
be generated (and to be read and dropped by the interrupt handler)
before sending the next command.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the first PCM device from "Analog" to "Multichannel" because it
can be used for HDMI output on the Xonar HDAV.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the callback function that switches between line and mic inputs
on the Xonar D1 because it is also usable on other models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Do not use a hardcoded number when iterating over the PCM1796 DACs to
allow for cards with a different number of analog output channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce some trivial functions to better document the relationships of
the various model callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add functions to allow model drivers to communicate with external chips
by doing I/O with the not-used-for-MIDI UART.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
To enable the MIDI port, model drivers must now set flags in
device_config, not only in misc_flags. This allows model drivers to
enable the UART without creating an ALSA MIDI device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Rename the pcm_dev_cfg field to device_config because there will be
additional flags that do not describe PCM devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Factor out the common code of the mixer callbacks that handle controls
that just switch a single GPIO bit.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The Xonar D2X and DX are very similar to the D2 and D1, respectively, so
we can handle the differences dynamically instead of using a separate
model structure for each one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Handle the differences between the X-Meridian and the other models in
the probe callback instead of using a second model structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Introduce symbols that indicate the two models handled by the snd-oxygen
driver, instead of using a magic number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a probe callback to the model structure so that model-specific
drivers can refine their model detection before the card is initialized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Put a copy of the model structure into the chip structure so that model-
specific drivers can modify it depending on a particular device
instance.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When setting the SPDIF channel status sample rate field, use the
recently defined symbols instead of magic numbers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Xonar DX does not have CD Capture controls, so we have to check that
a control actually exists before muting it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the Asus Xonar D1. It is the same as the DX, but
without the external power detection.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a constraint for the period time so that there are less than ten
seconds between interrupts so that ALSA does not assume that the device
is dead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Introduce symbols for the buffer/period size constraints so that their
limits and relationships become clearer.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the setting of the output enable GPIO bit to a separate function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Create separate functions for the code that initializes the hardware, as
opposed to initializing internal driver state, so that they can be
reused for resume support.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When initializing the DAC volume registers, we can just use the generic
volume update functions instead of setting the registers manually.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Save the written values of all CMI8788 and AC97 registers and of some of
the DAC/ADC registers so that it is possible to restore the register
state later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove another magic number - add a symbol for the size of the PCI I/O
range.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Adjust the MODULE_LICENSE strings to properly reflect the actual license.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clemens Ladisch