It allocates the extended area for outbound streams only on sendmsg
calls, if they are not yet allocated. When using the priority
stream scheduler, this initialization may imply into a subsequent
allocation, which may fail. In this case, it was aborting the stream
scheduler initialization but leaving the ->ext pointer (allocated) in
there, thus in a partially initialized state. On a subsequent call to
sendmsg, it would notice the ->ext pointer in there, and trip on
uninitialized stuff when trying to schedule the data chunk.
The fix is undo the ->ext initialization if the stream scheduler
initialization fails and avoid the partially initialized state.
Although syzkaller bisected this to commit 4ff40b8626 ("sctp: set
chunk transport correctly when it's a new asoc"), this bug was actually
introduced on the commit I marked below.
Reported-by: syzbot+c1a380d42b190ad1e559@syzkaller.appspotmail.com
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the skb is associated with a new sock, just assigning
it to skb->sk is not sufficient, we have to set its destructor
to free the sock properly too.
Reported-by: syzbot+d6636a36d3c34bd88938@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the situation where an IPV6 only flag is applied to an IPv4 address:
# ip addr add 192.0.2.1/24 dev dummy0 nodad home mngtmpaddr noprefixroute
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global noprefixroute dummy0
valid_lft forever preferred_lft forever
Or worse, by sending a malicious netlink command:
# ip -4 addr show dev dummy0
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 192.0.2.1/24 scope global nodad optimistic dadfailed home tentative mngtmpaddr noprefixroute stable-privacy dummy0
valid_lft forever preferred_lft forever
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skbs may have their checksum value populated by HW. If this is a checksum
calculated over the entire packet then the CHECKSUM_COMPLETE field is
marked. Changes to the data pointer on the skb throughout the network
stack still try to maintain this complete csum value if it is required
through functions such as skb_postpush_rcsum.
The MPLS actions in Open vSwitch modify a CHECKSUM_COMPLETE value when
changes are made to packet data without a push or a pull. This occurs when
the ethertype of the MAC header is changed or when MPLS lse fields are
modified.
The modification is carried out using the csum_partial function to get the
csum of a buffer and add it into the larger checksum. The buffer is an
inversion of the data to be removed followed by the new data. Because the
csum is calculated over 16 bits and these values align with 16 bits, the
effect is the removal of the old value from the CHECKSUM_COMPLETE and
addition of the new value.
However, the csum fed into the function and the outcome of the
calculation are also inverted. This would only make sense if it was the
new value rather than the old that was inverted in the input buffer.
Fix the issue by removing the bit inverts in the csum_partial calculation.
The bug was verified and the fix tested by comparing the folded value of
the updated CHECKSUM_COMPLETE value with the folded value of a full
software checksum calculation (reset skb->csum to 0 and run
skb_checksum_complete(skb)). Prior to the fix the outcomes differed but
after they produce the same result.
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to kernel")
Fixes: bc7cc5999f ("openvswitch: update checksum in {push,pop}_mpls")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter did not expect that skb_dst_force() can cause skb to lose its
dst entry.
I got a bug report with a skb->dst NULL dereference in netfilter
output path. The backtrace contains nf_reinject(), so the dst might have
been cleared when skb got queued to userspace.
Other users were fixed via
if (skb_dst(skb)) {
skb_dst_force(skb);
if (!skb_dst(skb))
goto handle_err;
}
But I think its preferable to make the 'dst might be cleared' part
of the function explicit.
In netfilter case, skb with a null dst is expected when queueing in
prerouting hook, so drop skb for the other hooks.
v2:
v1 of this patch returned true in case skb had no dst entry.
Eric said:
Say if we have two skb_dst_force() calls for some reason
on the same skb, only the first one will return false.
This now returns false even when skb had no dst, as per Erics
suggestion, so callers might need to check skb_dst() first before
skb_dst_force().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when sctp_connect() is called with a wrong sa_family, it binds
to a port but doesn't set bp->port, then sctp_get_af_specific will
return NULL and sctp_connect() returns -EINVAL.
Then if sctp_bind() is called to bind to another port, the last
port it has bound will leak due to bp->port is NULL by then.
sctp_connect() doesn't need to bind ports, as later __sctp_connect
will do it if bp->port is NULL. So remove it from sctp_connect().
While at it, remove the unnecessary sockaddr.sa_family len check
as it's already done in sctp_inet_connect.
Fixes: 644fbdeacf ("sctp: fix the issue that flags are ignored when using kernel_connect")
Reported-by: syzbot+079bf326b38072f849d9@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix memleak reported by syzkaller when registering IPVS hooks,
patch from Julian Anastasov.
2) Fix memory leak in start_sync_thread, also from Julian.
3) Fix conntrack deletion via ctnetlink, from Felix Kaechele.
4) Fix reject for ICMP due to incorrect checksum handling, from
He Zhe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since v5.1-rc1, some types of packets do not get unreachable reply with the
following iptables setting. Fox example,
$ iptables -A INPUT -p icmp --icmp-type 8 -j REJECT
$ ping 127.0.0.1 -c 1
PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data.
— 127.0.0.1 ping statistics —
1 packets transmitted, 0 received, 100% packet loss, time 0ms
We should have got the following reply from command line, but we did not.
From 127.0.0.1 icmp_seq=1 Destination Port Unreachable
Yi Zhao reported it and narrowed it down to:
7fc3822536 ("netfilter: reject: skip csum verification for protocols that don't support it"),
This is because nf_ip_checksum still expects pseudo-header protocol type 0 for
packets that are of neither TCP or UDP, and thus ICMP packets are mistakenly
treated as TCP/UDP.
This patch corrects the conditions in nf_ip_checksum and all other places that
still call it with protocol 0.
Fixes: 7fc3822536 ("netfilter: reject: skip csum verification for protocols that don't support it")
Reported-by: Yi Zhao <yi.zhao@windriver.com>
Signed-off-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- fix a leaked TVLV handler which wasn't unregistered, by Jeremy Sowden
- fix duplicated OGMs when interfaces are set UP, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=TqkI
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20190627' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix a leaked TVLV handler which wasn't unregistered, by Jeremy Sowden
- fix duplicated OGMs when interfaces are set UP, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix ppp_mppe crypto soft dependencies, from Takashi Iawi.
2) Fix TX completion to be finite, from Sergej Benilov.
3) Use register_pernet_device to avoid a dst leak in tipc, from Xin
Long.
4) Double free of TX cleanup in Dirk van der Merwe.
5) Memory leak in packet_set_ring(), from Eric Dumazet.
6) Out of bounds read in qmi_wwan, from Bjørn Mork.
7) Fix iif used in mcast/bcast looped back packets, from Stephen
Suryaputra.
8) Fix neighbour resolution on raw ipv6 sockets, from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET
sctp: change to hold sk after auth shkey is created successfully
ipv6: fix neighbour resolution with raw socket
ipv6: constify rt6_nexthop()
net: dsa: microchip: Use gpiod_set_value_cansleep()
net: aquantia: fix vlans not working over bridged network
ipv4: reset rt_iif for recirculated mcast/bcast out pkts
team: Always enable vlan tx offload
net/smc: Fix error path in smc_init
net/smc: hold conns_lock before calling smc_lgr_register_conn()
bonding: Always enable vlan tx offload
net/ipv6: Fix misuse of proc_dointvec "skip_notify_on_dev_down"
ipv4: Use return value of inet_iif() for __raw_v4_lookup in the while loop
qmi_wwan: Fix out-of-bounds read
tipc: check msg->req data len in tipc_nl_compat_bearer_disable
net: macb: do not copy the mac address if NULL
net/packet: fix memory leak in packet_set_ring()
net/tls: fix page double free on TX cleanup
net/sched: cbs: Fix error path of cbs_module_init
tipc: change to use register_pernet_device
...
When an application is run that:
a) Sets its scheduler to be SCHED_FIFO
and
b) Opens a memory mapped AF_PACKET socket, and sends frames with the
MSG_DONTWAIT flag cleared, its possible for the application to hang
forever in the kernel. This occurs because when waiting, the code in
tpacket_snd calls schedule, which under normal circumstances allows
other tasks to run, including ksoftirqd, which in some cases is
responsible for freeing the transmitted skb (which in AF_PACKET calls a
destructor that flips the status bit of the transmitted frame back to
available, allowing the transmitting task to complete).
However, when the calling application is SCHED_FIFO, its priority is
such that the schedule call immediately places the task back on the cpu,
preventing ksoftirqd from freeing the skb, which in turn prevents the
transmitting task from detecting that the transmission is complete.
We can fix this by converting the schedule call to a completion
mechanism. By using a completion queue, we force the calling task, when
it detects there are no more frames to send, to schedule itself off the
cpu until such time as the last transmitted skb is freed, allowing
forward progress to be made.
Tested by myself and the reporter, with good results
Change Notes:
V1->V2:
Enhance the sleep logic to support being interruptible and
allowing for honoring to SK_SNDTIMEO (Willem de Bruijn)
V2->V3:
Rearrage the point at which we wait for the completion queue, to
avoid needing to check for ph/skb being null at the end of the loop.
Also move the complete call to the skb destructor to avoid needing to
modify __packet_set_status. Also gate calling complete on
packet_read_pending returning zero to avoid multiple calls to complete.
(Willem de Bruijn)
Move timeo computation within loop, to re-fetch the socket
timeout since we also use the timeo variable to record the return code
from the wait_for_complete call (Neil Horman)
V3->V4:
Willem has requested that the control flow be restored to the
previous state. Doing so lets us eliminate the need for the
po->wait_on_complete flag variable, and lets us get rid of the
packet_next_frame function, but introduces another complexity.
Specifically, but using the packet pending count, we can, if an
applications calls sendmsg multiple times with MSG_DONTWAIT set, each
set of transmitted frames, when complete, will cause
tpacket_destruct_skb to issue a complete call, for which there will
never be a wait_on_completion call. This imbalance will lead to any
future call to wait_for_completion here to return early, when the frames
they sent may not have completed. To correct this, we need to re-init
the completion queue on every call to tpacket_snd before we enter the
loop so as to ensure we wait properly for the frames we send in this
iteration.
Change the timeout and interrupted gotos to out_put rather than
out_status so that we don't try to free a non-existant skb
Clean up some extra newlines (Willem de Bruijn)
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_endpoint_init(), it holds the sk then creates auth
shkey. But when the creation fails, it doesn't release the sk,
which causes a sk defcnf leak,
Here to fix it by only holding the sk when auth shkey is created
successfully.
Fixes: a29a5bd4f5 ("[SCTP]: Implement SCTP-AUTH initializations.")
Reported-by: syzbot+afabda3890cc2f765041@syzkaller.appspotmail.com
Reported-by: syzbot+276ca1c77a19977c0130@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scenario is the following: the user uses a raw socket to send an ipv6
packet, destinated to a not-connected network, and specify a connected nh.
Here is the corresponding python script to reproduce this scenario:
import socket
IPPROTO_RAW = 255
send_s = socket.socket(socket.AF_INET6, socket.SOCK_RAW, IPPROTO_RAW)
# scapy
# p = IPv6(src='fd00💯:1', dst='fd00:200::fa')/ICMPv6EchoRequest()
# str(p)
req = b'`\x00\x00\x00\x00\x08:@\xfd\x00\x01\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x01\xfd\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\xfa\x80\x00\x81\xc0\x00\x00\x00\x00'
send_s.sendto(req, ('fd00:175::2', 0, 0, 0))
fd00:175::/64 is a connected route and fd00:200::fa is not a connected
host.
With this scenario, the kernel starts by sending a NS to resolve
fd00:175::2. When it receives the NA, it flushes its queue and try to send
the initial packet. But instead of sending it, it sends another NS to
resolve fd00:200::fa, which obvioulsy fails, thus the packet is dropped. If
the user sends again the packet, it now uses the right nh (fd00:175::2).
The problem is that ip6_dst_lookup_neigh() uses the rt6i_gateway, which is
:: because the associated route is a connected route, thus it uses the dst
addr of the packet. Let's use rt6_nexthop() to choose the right nh.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change in this patch, it only prepares the next one.
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast or broadcast egress packets have rt_iif set to the oif. These
packets might be recirculated back as input and lookup to the raw
sockets may fail because they are bound to the incoming interface
(skb_iif). If rt_iif is not zero, during the lookup, inet_iif() function
returns rt_iif instead of skb_iif. Hence, the lookup fails.
v2: Make it non vrf specific (David Ahern). Reword the changelog to
reflect it.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_pernet_subsys success in smc_init,
we should cleanup it in case any other error.
Fixes: 64e28b52c7 (net/smc: add pnet table namespace support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After smc_lgr_create(), the newly created link group is added
to smc_lgr_list, thus is accessible from other context.
Although link group creation is serialized by
smc_create_lgr_pending, the new link group may still be accessed
concurrently. For example, if ib_device is no longer active,
smc_ib_port_event_work() will call smc_port_terminate(), which
in turn will call __smc_lgr_terminate() on every link group of
this device. So conns_lock is required here.
Signed-off-by: Huaping Zhou <zhp@smail.nju.edu.cn>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f8e6089820 ("netfilter: ctnetlink: Resolve conntrack
L3-protocol flush regression") introduced a regression in which deletion
of conntrack entries would fail because the L3 protocol information
is replaced by AF_UNSPEC. As a result the search for the entry to be
deleted would turn up empty due to the tuple used to perform the search
is now different from the tuple used to initially set up the entry.
For flushing the conntrack table we do however want to keep the option
for nfgenmsg->version to have a non-zero value to allow for newer
user-space tools to request treatment under the new behavior. With that
it is possible to independently flush tables for a defined L3 protocol.
This was introduced with the enhancements in in commit 59c08c69c2
("netfilter: ctnetlink: Support L3 protocol-filter on flush").
Older user-space tools will retain the behavior of flushing all tables
regardless of defined L3 protocol.
Fixes: f8e6089820 ("netfilter: ctnetlink: Resolve conntrack L3-protocol flush regression")
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Felix Kaechele <felix@kaechele.ca>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
/proc/sys/net/ipv6/route/skip_notify_on_dev_down assumes given value to be
0 or 1. Use proc_dointvec_minmax instead of proc_dointvec.
Fixes: 7c6bb7d2fa ("net/ipv6: Add knob to skip DELROUTE message ondevice down")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 19e4e76806 ("ipv4: Fix raw socket lookup for local
traffic"), the dif argument to __raw_v4_lookup() is coming from the
returned value of inet_iif() but the change was done only for the first
lookup. Subsequent lookups in the while loop still use skb->dev->ifIndex.
Fixes: 19e4e76806 ("ipv4: Fix raw socket lookup for local traffic")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix an uninit-value issue, reported by syzbot:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:981
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
memchr+0xce/0x110 lib/string.c:981
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_disable+0x2a1/0x480 net/tipc/netlink_compat.c:449
__tipc_nl_compat_doit net/tipc/netlink_compat.c:327 [inline]
tipc_nl_compat_doit+0x3ac/0xb00 net/tipc/netlink_compat.c:360
tipc_nl_compat_handle net/tipc/netlink_compat.c:1178 [inline]
tipc_nl_compat_recv+0x1b1b/0x27b0 net/tipc/netlink_compat.c:1281
TLV_GET_DATA_LEN() may return a negtive int value, which will be
used as size_t (becoming a big unsigned long) passed into memchr,
cause this issue.
Similar to what it does in tipc_nl_compat_bearer_enable(), this
fix is to return -EINVAL when TLV_GET_DATA_LEN() is negtive in
tipc_nl_compat_bearer_disable(), as well as in
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
v1->v2:
- add the missing Fixes tags per Eric's request.
Fixes: 0762216c0a ("tipc: fix uninit-value in tipc_nl_compat_bearer_enable")
Fixes: 8b66fee7f8 ("tipc: fix uninit-value in tipc_nl_compat_link_reset_stats")
Reported-by: syzbot+30eaa8bf392f7fafffaf@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot found we can leak memory in packet_set_ring(), if user application
provides buggy parameters.
Fixes: 7f953ab2ba ("af_packet: TX_RING support for TPACKET_V3")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_qdisc fails, we should unregister
netdevice notifier.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e0a7683d30 ("net/sched: cbs: fix port_rate miscalculation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a dst defcnt leak, which can be reproduced by doing:
# ip net a c; ip net a s; modprobe tipc
# ip net e s ip l a n eth1 type veth peer n eth1 netns c
# ip net e c ip l s lo up; ip net e c ip l s eth1 up
# ip net e s ip l s lo up; ip net e s ip l s eth1 up
# ip net e c ip a a 1.1.1.2/8 dev eth1
# ip net e s ip a a 1.1.1.1/8 dev eth1
# ip net e c tipc b e m udp n u1 localip 1.1.1.2
# ip net e s tipc b e m udp n u1 localip 1.1.1.1
# ip net d c; ip net d s; rmmod tipc
and it will get stuck and keep logging the error:
unregister_netdevice: waiting for lo to become free. Usage count = 1
The cause is that a dst is held by the udp sock's sk_rx_dst set on udp rx
path with udp_early_demux == 1, and this dst (eventually holding lo dev)
can't be released as bearer's removal in tipc pernet .exit happens after
lo dev's removal, default_device pernet .exit.
"There are two distinct types of pernet_operations recognized: subsys and
device. At creation all subsys init functions are called before device
init functions, and at destruction all device exit functions are called
before subsys exit function."
So by calling register_pernet_device instead to register tipc_net_ops, the
pernet .exit() will be invoked earlier than loopback dev's removal when a
netns is being destroyed, as fou/gue does.
Note that vxlan and geneve udp tunnels don't have this issue, as the udp
sock is released in their device ndo_stop().
This fix is also necessary for tipc dst_cache, which will hold dsts on tx
path and I will introduce in my next patch.
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to align the minimum encryption key size requirement for
Bluetooth connections, it turns out doing this in a central location in
the HCI connection handling code is not possible.
Original Bluetooth version up to 2.0 used a security model where the
L2CAP service would enforce authentication and encryption. Starting
with Bluetooth 2.1 and Secure Simple Pairing that model has changed into
that the connection initiator is responsible for providing an encrypted
ACL link before any L2CAP communication can happen.
Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and
before devices are causing a regression. The encryption key size check
needs to be moved out of the HCI connection handling into the L2CAP
channel setup.
To achieve this, the current check inside hci_conn_security() has been
moved into l2cap_check_enc_key_size() helper function and then called
from four decisions point inside L2CAP to cover all combinations of
Secure Simple Pairing enabled devices and device using legacy pairing
and legacy service security model.
Fixes: d5bb334a8e ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
tcp_fragment() might be called for skbs in the write queue.
Memory limits might have been exceeded because tcp_sendmsg() only
checks limits at full skb (64KB) boundaries.
Therefore, we need to make sure tcp_fragment() wont punish applications
that might have setup very low SO_SNDBUF values.
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bugfixes:
- SUNRPC: Fix a credential refcount leak
- Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
- SUNRPC: Fix xps refcount imbalance on the error path
- NFS4: Only set creation opendata if O_CREAT
-----BEGIN PGP SIGNATURE-----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=+z30
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.2-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull more NFS client fixes from Anna Schumaker:
"These are mostly refcounting issues that people have found recently.
The revert fixes a suspend recovery performance issue.
- SUNRPC: Fix a credential refcount leak
- Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
- SUNRPC: Fix xps refcount imbalance on the error path
- NFS4: Only set creation opendata if O_CREAT"
* tag 'nfs-for-5.2-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Fix a credential refcount leak
Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
net :sunrpc :clnt :Fix xps refcount imbalance on the error path
NFS4: Only set creation opendata if O_CREAT
All callers of __rpc_clone_client() pass in a value for args->cred,
meaning that the credential gets assigned and referenced in
the call to rpc_new_client().
Reported-by: Ido Schimmel <idosch@idosch.org>
Fixes: 79caa5fad4 ("SUNRPC: Cache cred of process creating the rpc_client")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Jon Hunter reports:
"I have been noticing intermittent failures with a system suspend test on
some of our machines that have a NFS mounted root file-system. Bisecting
this issue points to your commit 431235818b ("SUNRPC: Declare RPC
timers as TIMER_DEFERRABLE") and reverting this on top of v5.2-rc3 does
appear to resolve the problem.
The cause of the suspend failure appears to be a long delay observed
sometimes when resuming from suspend, and this is causing our test to
timeout."
This reverts commit 431235818b.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
rpc_clnt_add_xprt take a reference to struct rpc_xprt_switch, but forget
to release it before return, may lead to a memory leak.
Signed-off-by: Lin Yi <teroincn@163.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
A user reported that routes are getting installed with type 0 (RTN_UNSPEC)
where before the routes were RTN_UNICAST. One example is from accel-ppp
which apparently still uses the ioctl interface and does not set
rtmsg_type. Another is the netlink interface where ipv6 does not require
rtm_type to be set (v4 does). Prior to the commit in the Fixes tag the
ipv6 stack converted type 0 to RTN_UNICAST, so restore that behavior.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when running as VM guest (ie pr_iucv != NULL), af_iucv can still
open HiperTransport-based connections. For robust operation these
connections require the af_iucv_netdev_notifier, so register it
unconditionally.
Also handle any error that register_netdevice_notifier() returns.
Fixes: 9fbd87d413 ("af_iucv: handle netdev events")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HiperSockets-based transport path in af_iucv is still too closely
entangled with qeth.
With commit a647a02512 ("s390/qeth: speed-up L3 IQD xmit"), the
relevant xmit code in qeth has begun to use skb_cow_head(). So to avoid
unnecessary skb head expansions, af_iucv must learn to
1) respect dev->needed_headroom when allocating skbs, and
2) drop the header reference before cloning the skb.
While at it, also stop hard-coding the LL-header creation stage and just
use the appropriate helper.
Fixes: a647a02512 ("s390/qeth: speed-up L3 IQD xmit")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_iucv sockets over z/VM IUCV require that their skbs are allocated
in DMA memory. This restriction doesn't apply to connections over
HiperSockets. So only set this limit for z/VM IUCV sockets, thereby
increasing the likelihood that the large (and linear!) allocations for
HiperTransport messages succeed.
Fixes: 3881ac441f ("af_iucv: add HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 58 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.556988620@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation see readme and copying for
more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.060259192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this source code is licensed under general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 5 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081204.871734026@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this work is licensed under the terms of the gnu gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 48 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081204.624030236@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this source code is licensed under the gnu general public license
version 2 see the file copying for more details
this source code is licensed under general public license version 2
see
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.449021192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Module autoload for masquerade and redirection does not work.
2) Leak in unqueued packets in nf_ct_frag6_queue(). Ignore duplicated
fragments, pretend they are placed into the queue. Patches from
Guillaume Nault.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner