In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46f ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set
descriptor"), all the routines that get fields from a descriptor were
changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of variables are initialized when declared that set later in the
routine, thus the initialization can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the call to hw_init() fails for any of the drivers, the driver will
leak memory that was allocated in BT coexistence setup. Technically, each
of the drivers should have done this free; however placing it in rtl_pci
fixes all the drivers with only a single patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.
This error has been in the driver since its initial submission.
Fixes: 29d00a3e46 ("rtlwifi: rtl8192cu: Add routine trx")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spurious warning message when building with W=1:
CC [M] drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand * on line 790 - I thought it was a doc line
Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration variable IS_LITTLE_ENDIAN is replaced by the standard
__LITTLE_ENDIAN. In addition, an unused struct is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now _rtl_dump_channel_map() does not do any actual
thing using the channel. So remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Module parameters of 'sw_crypto' and 'disable_watchdog' are false by
default. If new value is desired, we can do it during inserting module,
assignment existing in source code is not reasonable.
Reported-by: David Binderman <dcb314@hotmail.com>
CC: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
fix below issue reported by coccicheck
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:514:1-3:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable rtstatus is being initialized with a value that is never read
as rtstatus is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of 0 to variable k is never read once we break out of
the loop, so the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable badworden is assigned with a value that is never read and
it is re-assigned a new value immediately afterwards. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c: In function rtl_btc_btmpinfo_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c:319:17: warning: variable len set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function exhalbtc_connect_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1581:16: warning: variable asso_type_v2 set but not used [-Wunused-but-set-variable]
'len' is never used since commit 6aad6075cc ("rtlwifi:
Add BT_MP_INFO to c2h handler.") so can be removed.
'asso_type_v2' is not used since introduction in
commit 0843e98a3b ("rtlwifi: btcoex: add assoc
type v2 to connection notify")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_rssi_monitor:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:658:6: warning: variable cur_txokcnt set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_edca_turbo:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2657:7: warning: variable b_last_is_cur_rdl_state set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cckswing tables cckswing_table_ch1ch13 and cckswing_table_ch14 are
u8 array in little-endian order. To compare four u8 value with register
u32 value, cast the value to cpu order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ofdm_index_old[] is the index of ofdmswing_table[], and used to indicate
initial value of ROFDM0_X{A,B}TXIQIMBALANCE in rtl8192de_phy_reg_2tarray[]
table, and the initial value is corresponding to calibration thermal value
written in efuse, namely rtlefuse->eeprom_thermalmeter. Then, local
variable ofdm_index_old[] save to rtlpriv->dm.ofdm_index[] for operational
use.
If thermal value (temperature) is increasing, output TX power is lower.
So, we calculate the delta between current and calibration thermal value,
then add power to yield expected and the same output TX power.
Thus, ofdm_index[] should be initialized as rtlpriv->dm.ofdm_index[], and
shift to proper index depends on delta of thermal value. Then, new power
value ofdmswing_table[ofdm_index[]] is written to register.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can reduce code size 264 bytes, and make code more readable.
text data bss dec hex filename
Before: 13586 0 16 13602 3522 rtl8192de/dm.o
After: 13322 0 16 13338 341a rtl8192de/dm.o
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit doesn't change logic at all. Since indentation is lower, the
wrapped statements can be put in single line that will become more
readable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c: In function 'rtl92cu_phy_rf6052_set_cck_txpower':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:45:7: warning: variable 'turbo_scanoff' set but not used [-Wunused-but-set-variable]
It is not used any more since
commit e9b0784bb9 ("rtlwifi: rtl8192cu: Fix some code in RF handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 238ad2ddf3 ("rtlwifi: rtl8723ae: Clean up the hardware info routine")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix sparse warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c:666:6:
warning: symbol 'rtl8723e_dm_refresh_rate_adaptive_mask' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In five of the drivers, the contents of bits 29-31 of one of the RX
descriptors is used to set bits in a variable that is used to save the
wakeup condition for output in a debugging statement. The resulting
variable is not used anywhere else even though it is stored in a struct
and could be available in other routines. This variable is changed to be
local.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In drivers rtl8188ee, rtl8821ae, rtl8723be, and rtl8192ee, the reason
for a wake-up is returned in the fourth RX descriptor in bits 29-31. Due
to typographical errors, all but rtl8821ae test bit 31 twice and fail to
test bit 29.
This error causes no problems as the tests are only used to set bits in
the output of an optional debugging statement.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is unnecessary to call spin_lock_bh in a tasklet.
Signed-off-by: Jeff Xie <chongguiguzi@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dev_alloc_skb fails, the fix safely returns to avoid
potential NULL pointer dereference.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case alloc_workqueue fails, the fix reports the error and
returns to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127a ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following types of blank line problems are reported:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The problems filed include the following:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The errors consist of multiple blank lines, and a missing blank line
after the declarations.
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The instances where statement continuations are improperly aligned have
been fixed.
There are no changes to generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of problems with block comments.
These changes do not affect the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl report problems in wifi.h where spaces are missing, as well
as extraneous spaces.
There are no changes in the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is an uppercase 'N' that should be a lowercase 'n', fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+ SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
^
WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+ pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277:
+ ptmp_byte = (u8 *) (®toset) + index;
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329:
+ pwr_val[i] = (u8) ((writeval & (0x7f <<
CHECK: No space is necessary after a cast
#784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365:
+ (u8) writeval);
CHECK: spaces preferred around that '/' (ctx:VxV)
#963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513:
+ txqpageunit = txqpagenum/outepnum;
^
CHECK: Unnecessary parentheses around 'outepnum > 1'
#975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521:
+ if ((outepnum > 1) && (txqremaininpage))
CHECK: Alignment should match open parenthesis
#1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617:
+static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw,
bool wmm_enable,
ERROR: "foo * bar" should be "foo *bar"
#1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591:
+void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver contains one instance of a CamelCase variable, namely
IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbt_precomp.h contains the only CamelCase value, namely
GetDefaultAdapter, but that macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a number of CamelCase variables remaining in the source
files of modules rtl_pci, rtl_usb, and rtlwifi.
The following checkpatch excettions are also fixed:
for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch
-----------------------------------------------------------------------
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
WARNING: line over 80 characters
#70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379:
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
CHECK: No space is necessary after a cast
#186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396:
+ status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368:
+ stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc);
CHECK: No space is necessary after a cast
#265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
WARNING: Unnecessary space before function pointer arguments
#455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462:
+ void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf,
WARNING: Unnecessary space before function pointer arguments
#483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257:
+ void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old-style license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/base.c: In function 'rtl_c2h_content_parsing':
drivers/net/wireless/realtek/rtlwifi/base.c:2313:13: warning:
variable 'cmd_seq' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves the clearing of rtlpriv->link_info.num_rx_inperiod in
rtl_watchdog_wq_callback a few lines down.
This is necessary since it is still used in the "AP off" detection
code block. Moved clearing of rtlpriv->link_info.num_rx_inperiod
as well for consistency.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This re-introduces the function rtl8723e_dm_refresh_rate_adaptive_mask.
This function was present in a previous version of the code base,
it works just fine for me -- as long as it is not using stale data.
Unlike the original version of this function it avoids using
dm.undec_sm_pwdb when no beacon was received.
Fixed a style nit in rtl8723e_dm_init_rate_adaptive_mask.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When no beacon was received, the value in dm.undec_sm_pwdb is most
likely out of date and should not be used to adjust the input path.
Assume instead that the signal level is low.
Fix the state machine in rtl8723e_dm_cck_packet_detection_thresh
which did not clear pre_cck_fa_state when changing cur_cck_pd_state
from CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW to CCK_PD_STAGE_HIGHRSSI
and back again to CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW, the register
RCCK0_CCA not written to 0x83 on the second change.
Explicitly initialize pre_cck_fa_state/cur_cck_fa_state in
rtl_dm_diginit.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This appears to trigger a firmware bug and causes severe
problems with rtl8723ae PCI devices.
When the power save mode is activated for longer periods
of time the firmware stops to receive any packets.
This problem was exposed by commit 873ffe154a ("rtlwifi:
Fix logic error in enter/exit power-save mode").
Previously the power save mode was only active rarely and
only for a short time so that the problem was not noticeable.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c: In function 'translate_rx_signal_stuff':
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c:309:6: warning:
variable 'type' set but not used [-Wunused-but-set-variable]
It never used since commit 21e4b0726d ("rtlwifi: rtl8821ae: Move driver from
staging to regular tree")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing
C2H_BT_INFO"), calling rtl_c2hcmd_enqueue() with rtl_c2h_fast_cmd() true,
the routine returns without freeing that skb, thereby leaking it.
This issue has been discussed at https://github.com/lwfinger/rtlwifi_new/issues/401
and the fix tested there.
Fixes: 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing C2H_BT_INFO")
Reported-and-tested-by: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RT_TRACE shows REG_MCUFWDL value as a decimal value with a '0x'
prefix, which is somewhat misleading.
Fix it to print hexadecimal, as was intended.
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
radiob_array_table' and 'radiob_arraylen' are not used after setting its value.
It is safe to remove the unused variable. Meanwhile, radio B array should be
removed as well. because it will no longer be referenced.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function 'halbtc_leave_lps':
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:295:21: warning:
variable 'ppsc' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function 'halbtc_enter_lps':
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:318:21: warning:
variable 'ppsc' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit aa45a673b2 ("rtlwifi: btcoexist: Add new mini driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.
This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")
Thanks to Joe Perches for spotting this when I submitted an earlier patch.
Fixes: 3c05bedb5f ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_PCI;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_USB;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN;
~ ^~~~~~~~~~~~~~~~
3 warnings generated.
Use the values from the correct enumerated type, wifionly_chip_interface.
BTC_INTF_UNKNOWN = WIFIONLY_INTF_UNKNOWN = 0
BTC_INTF_PCI = WIFIONLY_INTF_PCI = 1
BTC_INTF_USB = WIFIONLY_INTF_USB = 2
Link: https://github.com/ClangBuiltLinux/linux/issues/135
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove set but unused variables from _rtl88ee_hw_configure() and
_rtl8723e_hw_configure().
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix following coccinelle warning:
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2952:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2961:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3011:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3020:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3439:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3448:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3339:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3348:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3074:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3083:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3192:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3201:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3267:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3276:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3124:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3133:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2821:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2830:2-4: WARNING: possible condition with no effect (if == else)
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sNaA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.
rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.
In this situation, driver gives message "Firmware is not ready to run!".
Fixes: fe89707f0a ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When connecting to AP, mac80211 asks driver to enter and leave PS quickly,
but driver deinit doesn't wait for delayed work complete when entering PS,
then driver reinit procedure and delay work are running simultaneously.
This will cause unpredictable kernel oops or crash like
rtl8723be: error H2C cmd because of Fw download fail!!!
WARNING: CPU: 3 PID: 159 at drivers/net/wireless/realtek/rtlwifi/
rtl8723be/fw.c:227 rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
CPU: 3 PID: 159 Comm: kworker/3:2 Tainted: G O 4.16.13-2-ARCH #1
Hardware name: ASUSTeK COMPUTER INC. X556UF/X556UF, BIOS X556UF.406
10/21/2016
Workqueue: rtl8723be_pci rtl_c2hcmd_wq_callback [rtlwifi]
RIP: 0010:rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
RSP: 0018:ffffa6ab01e1bd70 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffa26069071520 RCX: 0000000000000001
RDX: 0000000080000001 RSI: ffffffff8be70e9c RDI: 00000000ffffffff
RBP: 0000000000000000 R08: 0000000000000048 R09: 0000000000000348
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: ffffa26069071520 R14: 0000000000000000 R15: ffffa2607d205f70
FS: 0000000000000000(0000) GS:ffffa26081d80000(0000) knlGS:000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000443b39d3000 CR3: 000000037700a005 CR4: 00000000003606e0
Call Trace:
? halbtc_send_bt_mp_operation.constprop.17+0xd5/0xe0 [btcoexist]
? ex_btc8723b1ant_bt_info_notify+0x3b8/0x820 [btcoexist]
? rtl_c2hcmd_launcher+0xab/0x110 [rtlwifi]
? process_one_work+0x1d1/0x3b0
? worker_thread+0x2b/0x3d0
? process_one_work+0x3b0/0x3b0
? kthread+0x112/0x130
? kthread_create_on_node+0x60/0x60
? ret_from_fork+0x35/0x40
Code: 00 76 b4 e9 e2 fe ff ff 4c 89 ee 4c 89 e7 e8 56 22 86 ca e9 5e ...
This patch ensures all delayed works done before entering PS to satisfy
our expectation, so use cancel_delayed_work_sync() instead. An exception
is delayed work ips_nic_off_wq because running task may be itself, so add
a parameter ips_wq to deinit function to handle this case.
This issue is reported and fixed in below threads:
https://github.com/lwfinger/rtlwifi_new/issues/367https://github.com/lwfinger/rtlwifi_new/issues/366
Tested-by: Evgeny Kapun <abacabadabacaba@gmail.com> # 8723DE
Tested-by: Shivam Kakkar <shivam543@gmail.com> # 8723BE on 4.18-rc1
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: cceb0a5973 ("rtlwifi: Add work queue for c2h cmd.")
Cc: Stable <stable@vger.kernel.org> # 4.11+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bump the IEEE80211_MAX_AMPDU_BUF size to 0x100 for HE support
and - for now - use IEEE80211_MAX_AMPDU_BUF_HT everywhere.
This is derived from my internal patch, parts of which Luca
had sent upstream.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and refactor some code in order to avoid having identical code
for different branches.
Notice that the logic has been there since 2014.
Addresses-Coverity-ID: 1426199 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In former patch, I enqueu all C2H commands and processed by a workqueue.
In case C2H_BT_INFO will issue a H2C command to set BT reg, and wait for
a C2H ack. But it is totally impossible that C2H workqueue waits for a
C2H command, so kernel log warn
rtlwifi: :<0> btmpinfo wait (req_num=0) timeout
Since the C2H ack command C2H_BT_MP can be safely processed in interrupt
context, add a fast command path to deal with the command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The format of C2H data is ID(1 byte) + Length(1 byte) + value, and it is
more readable to use macros to access C2H data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use 'struct rtl_c2hcmd' to store C2H commands originally, and the code
is slightly complex to enqueue and dequeue and also wastes time to
allocate and memcpy data. Since C2H commands are asynchronous events,
they can be processed in work queue, so RX ISR enqueues C2H result in
removal of rtl_c2h_packet_handler().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The caller of hal_op rx_command_packet will assert function pointer
before calling, so we can remove dummy functions safely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IDs are defined by driver and map to the fw C2H IDs, but they aren't
used now result in removal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current chips use packet-based C2H commands whose IDs differ from old
ones, so this commit simply gives C2H_V0_ as prefix of command IDs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To use keep-alive mechanism in mac80211 stack, since driver supports
reporting accurate nullfunc frame tx ack now.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one
can be removed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:
Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
between commit:
77e30e10ee ("iwlwifi: mvm: query regdb for wmm rule if needed")
from the wireless-drivers tree and commits:
9c4f7d5127 ("iwlwifi: move all NVM parsing code to the common files")
4c625c564b ("iwlwifi: get rid of fw/nvm.c")
from the wireless-drivers-next tree.
Since the statements are identical, we can safely remove the statements.
The commit 42e74946f0 ("rtlwifi: btcoexist: Fix if == else warnings in
halbtc8821a1ant.c") had fixed the statements, but the commit c6821613e6
("rtlwifi: btcoex: follow linux coding style") that converted coding style
and upgraded btcoex didn't include the fix.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason. It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it. Also remove <linux/kmemleak.h> from source
files that do not use it.
This is tested on i386 allmodconfig and x86_64 allmodconfig. It would
be good to run it through the 0day bot for other $ARCHes. I have
neither the horsepower nor the storage space for the other $ARCHes.
Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms. Both of them reported 2 build failures
for which patches are included here (in v2).
[ slab.h is the second most used header file after module.h; kernel.h is
right there with slab.h. There could be some minor error in the
counting due to some #includes having comments after them and I didn't
combine all of those. ]
[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au> [2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [2 build failures]
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net?
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct comment. Set bit 3 and bit 4 of 0x0005 register (REG_APS_FSMCO + 1)
to 0 which means disable WL suspend, not enable WL suspend.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex support multiple platforms, but this drivers doesn't support full
functions yet, so this commit adds dummy definitions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New constant and variables definitions are used by btcoex of 8822b, so
this commit add them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In connection notify v1, btcoex only need to know start/end association,
and it will discriminate 2G and 5G band in v2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Normal LPS is decomposed into pre- and post- parts, so we can issue H2C
with TDMA parameters in the "critical section" that dirver can't change
LPS state at the moment.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get phydm's counter and version from the module phydm that is not
submitted so we implement dummy functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex use the rate to rsolve IOT issue that some APs reduce TX
rate quickly, so it uses the RX rate as a clue to decide TDMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger#lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex does different decision according to MCC or SCC status, but
driver is still SCC currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add customer_id field in structure, and then this is a clue to implement
the behavior defined by vendor LENOVO_CHINA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex uses dm's counters to check the environment is noisy or not. If it
is clean, btcoex set more time slots to WiFi so that it can transmit as
soon as possible. That will save time, and BT will have more time slots
after WiFi traffic is complete.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports "rtl_is_special_data() warn: inconsistent indenting", but
it is an obvious redundant statement so remove it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sparse reports some functions were not declared, so add 'static' as
modifier. Remove an unused function btc8821a1ant_is_wifi_status_changed()
exposed due to 'static'.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This was detected with static analysis using Coccinelle:
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c:1107:5-18:
duplicated argument to && or ||
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-8 points out that source and destination of the memcpy() are
always the same pointer, so the effect of memcpy() is undefined
here (its arguments must not overlap):
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c: In function '_rtl_rx_process':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:430:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Most likely this is harmless, but it's easy to just remove the
line and get rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
error: explicitly assigning value of variable of type 'u32'
(aka 'unsigned int') to itself [-Werror,-Wself-assign]
writeVal = writeVal;
Delete the branch with the self-assignment.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wifi only btcoex is used to solo card (without BT), and it is also
useful to exclude the interference with BT to make debug easier.
There are only four ops for wifi only btcoex to initialze antenna and
switch the settings while band is changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tell wifi and BT firmware the default port ID to set multiports' state
properly, but only 8822be needs this function currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new component phydm need to access efuse content, so we prepare ops
for reference.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add rf mask definition (BIT 0, BIT 1, BIT 2, ...) that is different from
rf path definition (0, 1, 2, ...), and then combinations of rf path are
possible.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NSS is a argument of highest rate in RC, and it occupies bit 4-7 so use
ieee80211_rate_set_vht() to fill the values. Since it got correct rate
index, we don't need to check chips to assign NSS in set function anymore.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add comments to make it to be easier to understand, and add compile time
assertions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In older design, the TX power is grouped into rate section (smaller array
size), but new design groups them into rate (larger array size). Thus,
we extend the size for both cases, and add compile time assertion.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In new design, SW_DEFINE[1:0] of tx desc are used by firmware, and the TX
report only contains SW_DEFINE[7:0]. To satisfy with all cases, driver uses
SW_DEFINE[7:2] as sequence number.
Besides, the format of tx report have been changed, so a new flag
RTL_SPEC_EXT_C2H is used to access report.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are going to add 8822be, which is a VHT 2x2 wifi chip, so add VHT flag
to replace enumeration of chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable the mac80211 fast-tx feature, since our driver already support
hw_flags required by fast-tx and is able to let mac80211 stack to transmit
packet through fast-xmit path.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit c713fb071e ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add 'static' or declaration to resolve the warnings, and remove two unused
functions halbtc_set_macreg() and halbtc_get_macreg() exposed when they
were made static.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New generation ICs will support 11ac, 5G, n-NSS, etc, so we define a set of
rate ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822be is 2x2 11ac wifi chip, so report VHT capability to mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable will be used by btcoex of 8822be, so we prepare this variable
in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT shares 2.4G band but not 5G band, so inform current band to btcoex to
setup antenna properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to the fact that A-MSDU deaggregation is done in software,
we set this flag to support the A-MSDU in A-MPDU
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex configure antenna by rfe_type that is RF type programmed in efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit implement the common function to sort old features, and add
more new features that are get_supported_feature, get_supported_version,
get_ant_det_val, ble_scan_type, ble_scan_para, bt_dev_info,
forbidden_slot_val, afh_map and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these typedefs are only referenced in a single location later
in this header. Thus, they are easily removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove global variables, so btcoexist can support multiple instances
simultaneously.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After mac power-on sequence, wifi will start to work so notify btcoex the
event to configure registers especially related to antenna. This will not
only help to assign antenna but also to yield better user experience.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP change bandwidth setting from 20M to 40M, STA may use old 20M AP
information to association with AP. Driver unlink bss in the
.bss_info_changed of ieee80211_ops to make sure that later scan can get
correct AP bandwidth capability.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there is no connection, driver will enter IPS state. Meanwhile, it
fails to scan channel 1 by the command 'iw dev wlan0 scan freq 2412',
because hardware channel setting lose after IPS. Thus, restore channel
setting from hw->conf.channel set by last rtl_op_config().
Signed-off-by: Tim Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enter/leavel IPS and LPS are large critical section, and they can't use
sleep function because running in atomic-context, which own a spin_lock.
In commit ba9f93f82a ("rtlwifi: Fix enter/exit power_save"), it moves
LPS functions to thread-context, so this commit can simply change LPS's
spin lock to mutex.
Considering IPS functions, rtl_ips_nic_on() may be called by TX tasklet
(softirq-context) that check whether packet is auth frame. Fortunately,
current mac80211 will ask driver to leave IPS using op_config with
changed flag IEEE80211_CONF_CHANGE_IDLE, before issuing auth frame, so
IPS functions can run in thread-context and use mutex to protect critical
section, too.
Also, this commit removes some useless spin locks.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable fw_ps_state is assigned a value but it is never read, hence
it is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:736:2:
warning: Value stored to 'fw_ps_state' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit fills FW version information of RTL8188EE and RTL8723, so
the btcoex can cooperate with FW correctly.
Also, we can display this version in debugfs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger