There are a lot of unused and uneccessary definitions in the header to
support the ColdFire 532x CPU family. Remove the junk.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Currently the setup code for the FEC multi-function pins on the ColdFire 528x
has the addresses hard coded in the code. Use the register defines that
already exist for this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Remove the last address definitions relative to the IPSBAR peripheral region
for the ColdFire 527x family. This involved cleaning up some magic numbers
used in the code part, and making them proper register definitions in the 527x
specific header.
This is part of the process of cleaning up the ColdFire register definitions
to make them consistently use absolute addresses for the primary registers.
This will reduce the occasional bugs caused by inconsistent definition of
the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The registers used to configure and set the multifunction pins on the 5272
ColdFire are defined as absolute addresses. So the use of them does not need
to be offset relative to the peripheral region address.
Fix two cases of incorrect usage of these addresses. Both affect UART
initialization, one in the common UART pin setup code, the other in the
NETtel board specific UART signal handling.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make the ColdFire 5249 MBAR peripheral register definitions absolute
addresses, instead of offsets into the region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make the remaining definitions of the 5272 ColdFire registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire MPARK and IRQ Assignment registers
absolute addresses. Currently some are relative to the MBAR peripheral
region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Chip Select registers absolute addresses.
Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Interrupt Source registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Pin Assignment registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Software watchdog registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Reset and System registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the abolsute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make all definitions of the ColdFire Interrupt Mask and Pending registers
absolute addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Let the compiler choose which register to use in the cache flushing
asm statements, instead of imposing %d0.
Additionally, fix two typo's.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
DRAGEN2 should obviously be CONFIG_DRAGEN2, but the screen.h entry it
triggers only references files that are nowhere to be found in the
current tree. Besides, nothing uses screen.h. So just drop all that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m68k's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: m68k <linux-m68k@lists.linux-m68k.org>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The managed clk functions are currently only available when the generic clk
lookup framework is build. But the managed clk functions are merely wrappers
around clk_get and clk_put and do not depend on any specifics of the generic
lookup functions and there are still quite a few custom implementations of the
clk API. So make the managed functions available whenever the clk API is
implemented.
The patch also removes the custom implementation of devm_clk_get for the
coldfire platform.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It was scheduled to be removed for a long time.
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netfilter@vger.kernel.org
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/ptr_ret.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/ptr_ret.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/ptr_ret.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is no specific atomic64 support code for any m68k CPUs, so we should
select CONFIG_GENERIC_ATOMC64 for all. Remove the existing per CPU selection
of this and select it for all m68k.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Every tty driver needs tty_port for each line. So let us add one to
nfcon too. And link it so that the tty layer knows about it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
m68k/apollo: Rename "timer" to "apollo_timer"
zorro: Remove unused zorro_bus.devices
m68k: Remove never used asm/shm.h
m68k/sun3: Remove unselectable code in prom_init()
m68k: Use asm-generic version of <asm/sections.h>
m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
mtd/uclinux: Use generic __bss_stop instead of _ebss
m68knommu: Allow ColdFire CPUs to use unaligned accesses
m68k: Remove five unused headers
m68k: CPU32 does not support unaligned accesses
m68k: Introduce config option CPU_HAS_NO_UNALIGNED
m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
m68k: Move CPU_HAS_* config options
m68k: Remove duplicate FPU config option
m68knommu: Clean up printing of sections
m68k: Use asm-generic version of <asm/types.h>
m68k: Use Kbuild logic to import asm-generic headers
User space access must always go through uaccess accessors, since on
classic m68k user space and kernel space are completely separate.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68knommu arch update from Greg Ungerer:
"Quite a varied set of changes this time.
- A little more merge cleanup, this time the assembler entry code.
- New sub-architecture support for the ColdFire 5251/5253 and 5441x
CPU families.
- Specific clk support code for the ColdFire 520x and 532x CPU
familes.
- Refactoring of the ColdFire GPIO support.
- PCI bus support for some ColdFire CPUS that have PCI hardware (54xx
family). This showed up a few problems with ColdFire cache,
allocating coherent memory and bi-directional DMA support. Fixes
for those too."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68k: allow PCI bus to be enabled for ColdFire m54xx CPUs
m68k: add PCI bus code support for the ColdFire M54xx SoC family
m68k: add IO access definitions to support PCI on ColdFire platforms
m68k: add PCI bus support definitions for the ColdFire M54xx SoC family
m68k: common PCI support definitions and code
m68k: add support for DMA_BIDIRECTIONAL in dma support functions
m68k: fix ColdFire clear cache operation
m68k: use simpler dma_alloc_coherent() for ColdFire CPUs
m68knommu: platform support for 8390 based ethernet used on some boards
m68knommu: Add clk definitions for m532x.
m68knommu: Add clk definitions for m520x.
m68knommu: Add rtc device for m5441x.
m68knommu: add definitions for the third interrupt controller on devices that don't have a third interrupt controller.
m68knommu: Add support for the Coldfire m5441x.
m68knommu: use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1
coldfire-qspi: Add support for the Coldfire 5251/5253.
m68knommu: Add support for the Coldfire 5251/5253
m68knommu: refactor Coldfire GPIO not to require GPIOLIB, eliminate mcf_gpio_chips.
m68k: merge the MMU and non-MMU versions of the entry.S code
m68k: use jbsr to call functions instead of bsrl
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
In file included from include/linux/kgdb.h:17,
from include/linux/fb.h:8,
from drivers/video/dnfb.c:15:
include/linux/serial_8250.h:71: error: expected identifier or ‘(’ before numeric constant
include/linux/serial_8250.h:72: error: expected ‘;’ before ‘struct’
make[1]: *** [drivers/video/dnfb.o] Error 1
This is caused by
#define timer (IO_BASE + timer_physaddr)
in <asm/apollohw.h>, which conflicts with the new "timer" struct member in
<linux/serial_8250.h>.
Rename "timer" to "apollo_timer", as it's a way too generic name for a
global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
--
http://kisskb.ellerman.id.au/kisskb/buildresult/6739606/
All support code for the PCI bus hardware on the ColdFire 547x and 548x
CPUs is now in. Allow enabling of CONFIG_PCI for them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire M54xx SoC family have a traditional PCI bus interface.
Add the core support code to access and use this bus on these parts.
This code provides all the config space access functions and IO access
functions. It also carries out the PCI bus initialization and hooks into
the kernel PCI subsystem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Define the usual memory access functions (readb/writeb/...) and I/O space
functions (inb/outb/...) for PCI bus support on ColdFire CPU based platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add all the required definitoins to support the ColdFire M54xx SoC PCI
hardware unit. These are strait out of the MCF5475 Reference Manual.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Basic set of definitions and support code required to turn on CONFIG_PCI
for the m68k architecture. Nothing specific to any PCI implementation in
any m68k class CPU hardware yet.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The dma cache support functions do not currently support the direction flag
DMA_BIDIRECTIONAL. If a driver passes this direction to dma_map_single or
friends you will get console output like this:
dma_sync_single_for_device: unsupported dir 0
For example when using the Intel e100 ethernet driver on a ColdFire platform
with PCI bus. You will get a stream of these messages coming out.
Modify the dma cache support code adding support for DMA_BIDIRECTIONAL. It is
actioned by doing a cache push operation.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The code for clearing (invalidating) the ColdFire cache is actually performing
a push operation. Add functions to clear the cache, and fix cache_clear() to
call the appropriate clear cache function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
On all ColdFire platforms (whether MMU enabled or not) we want to use the
simple page based dma_alloc_coherent. We don't want the virtual mapping
version that is used on classic m68k setups. So modify the conditionals
to use the existing simpler dma_alloc_coherent on all ColdFire and non-MMU
builds.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Quite a few of Freescale's older ColdFire development boards used an NS8390
based ethernet interface. Add a platform definition for the resources used
by these devices so we can use it on these boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 532x has individually controllable clocks for it peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 520x has individually controllable clocks for its peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled for all of the clocks.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Extending the interrupt controller code in intc-simr.c to support the third
interrupt controller on the m5441x means we need to add defines (as 0) for the
third interrupt controller on devices that don't have a third interrupt
controller.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add support for the Coldfire 5441x (54410/54415/54416/54417/54418). Currently
we only support noMMU mode. It requires the PIT patch posted previously as it
uses the PIT instead of the dma timer as a clock source so we can get all that
GENERIC_CLOCKEVENTS goodness. It also adds some simple clk definitions and
very simple minded power management. The gpio code is tweeked and some
additional devices are added to devices.c. The Makefile uses -mv4e as
apparently, the only difference a v4m (m5441x) and a v4e is the later has a
FPU, which I don't think should matter to us in the kernel.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1 so we can support
those parts that have the pit1 interrupt on other than the first interrupt
controller.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
If we're not connecting external GPIO extenders via i2c or spi or whatever, we
probably don't need GPIOLIB. If we provide an alternate implementation of
the GPIOLIB functions to use when only on-chip GPIO is needed, we can change
ARCH_REQUIRE_GPIOLIB to ARCH_WANTS_OPTIONAL_GPIOLIB so that GPIOLIB becomes
optional.
The downside is that in the GPIOLIB=n case, we lose all error checking done by
gpiolib, ie multiply allocating the gpio, free'ing gpio etc., so that the
only checking that can be done is if we reference a gpio on an external part.
Targets that need the extra error checking can still select GPIOLIB=y.
For the case where GPIOLIB=y, we can simplify the table of gpio chips to use a
single chip, eliminating the tables of chips in the 5xxx.c files. The
original motivation for the definition of multiple chips was to match the way
many of the Coldfire variants defined their gpio as a spare array in memory.
However, all this really gains us is some error checking when we request a
gpio, gpiolib can check that it doesn't fall in one of the holes. If thats
important, I think we can still come up with a better way of accomplishing
that.
Also in this patch is some general cleanup and reorganizing of the gpio header
files (I'm sure I must have had a reason why I sometimes used a prefix of
mcf_gpio and other times mcfgpio but for the life of me I can't think of it
now).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Some of the entry.S code is common to both MMU and non-MMU builds.
So merge the entry_no.S and entry_mm.S files back into a single file.
With a little code movement we only need a single #ifdef.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
There is a few places that the m68k entry code uses the bsrl instruction
to call other functions. That instruction is only supported on 68020 and
higher CPU types. If we use jbsr instead the code will be clean for all
68k and ColdFire CPU types.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The ret_from_excption code is referenced by its function name, or by a label
set at the start of its code. The non-MMU code can share some of this code
if we make direct calls to ret_from_exception instead of the associated label.
The effected function paths are: buserr, trap and ret_from_fork. So change
these to branch directly to ret_from_exception.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mcfne.h include contains definitions to support NS8390 eth based hardware
on ColdFire based CPU boards. So change its name to reflect that better.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
m68k's asm/shm.h header has been part of the tree ever since m68k
support got added in v1.3.94. (It started as /include/asm-m68k/shm.h and
moved to its current location a few years ago.) It seems it was never
used: no file ever included it and nothing used the macros it defines.
(Actually, from v2.5.46 until v2.6.29-rc3 it was included by m68knommu's
asm/shm.h. But that header was just a very thin wrapper for this header
and was itself unused too.)
This header can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This was copied from SPARC, but isn't relevant for the supported Sun-3
models.
[Geert] Also remove the related extern declarations, and update the
comment about prom_init().
Reported-by: Sarah Nadi <snadi@uwaterloo.ca>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
BSS_SECTION() provides the __bss_{start,stop} symbols, so there's no need
to wrap our own _[se]bss around it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
All of the current Linux supported ColdFire CPUs handle unaligned
memory accesses. So remove the CONFIG_CPU_HAS_NO_UNALIGNED option
selection for ColdFire. If we ever support a specific ColdFire CPU
that does not support unaligned accesses then we can insert the
CONFIG_CPU_HAS_NO_UNALIGNED for that specific CPU type.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There are five entirely unused headers in arch/m68k/include/asm. Nothing
includes these headers. And a few tests found no hits for the things
they provide (which makes sense).
MC68332.h, mac_mouse.h, and mcfmbus.h are all unused since at least
v2.6.12-rc2 (I didn't bother looking further back than that).
apollodma.h is unused since v2.6.19: commit
2ed0ce5b57 ("m68k/Apollo: Remove obsolete
arch/m68k/apollo/dma.c") removed the last file interested in that
header.
And everything interested in <asm/sbus.h> was removed in the v2.6.28
release cycle. The last occurrence of "sbus.h" was deleted with commit
0c0db98b50 ("sparc: Remove
Documentation/sparc/sbus_drivers.txt"). I'm not sure whether anything
relevant for m68k was included in v2.6.27, but it doesn't really matter.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Greg Ungerer<gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Commit f4d40de39a ("net fec: do not depend
on grouped clocks") breaks compilation of the FEC driver for non iMX
platforms in linux-3.5-rc1. For example when compiling for ColdFire I get:
LD vmlinux
drivers/built-in.o: In function `fec_probe':
fec.c:(.devinit.text+0x1e0): undefined reference to `devm_clk_get'
Define a simple devm_clk_get() function for the m68knommu architecture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull m68k update from Geert Uytterhoeven.
This makes m68k use the generic library functions for the user-space
strn[cpy|len] functions.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use generic strncpy_from_user(), strlen_user(), and strnlen_user()
The assembler entry code calls directly to the syscall_trace_enter() and
syscall_trace_leave() functions. But currently they are conditionaly
compiled out for the non-MMU classic m68k CPU types (so 68328 for example),
resulting in a link error:
LD vmlinux
arch/m68k/platform/68328/built-in.o: In function `do_trace':
(.text+0x1c): undefined reference to `syscall_trace_enter'
arch/m68k/platform/68328/built-in.o: In function `do_trace':
(.text+0x4c): undefined reference to `syscall_trace_leave'
Change the conditional check that includes these functions to be true for
the !defined(CONFIG_MMU) case as well.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Compiling for 68360 based targets fails with:
arch/m68k/platform/68360/config.c: In function ‘hw_tick’:
arch/m68k/platform/68360/config.c:55:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68360/config.c: At top level:
arch/m68k/platform/68360/config.c:64:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68328 based targets fails with:
arch/m68k/platform/68328/timers.c: In function ‘hw_tick’:
arch/m68k/platform/68328/timers.c:65:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68328/timers.c: At top level:
arch/m68k/platform/68328/timers.c:102:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When building for non-MMU based classic 68k CPU types (like the 68328 for
example) you get a compilation error:
CC arch/m68k/kernel/time.o
arch/m68k/kernel/time.c:91:5: error: redefinition of ‘arch_gettimeoffset’
include/linux/time.h:145:19: note: previous definition of ‘arch_gettimeoffset’ was here
The arch_gettimeoffset() code is included when building for these CPU types,
but it shouldn't be. Those machine types do not have
CONFIG_ARCH_USES_GETTIMEOFFSET set.
The fix is simply to conditionally include the arch_gettimeoffset() code on
that same config setting that specifies its use or not.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The consolidation of the qspi code missed a definition for 528x.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
- Remove casts and unneeded address-of ('&') operators,
- Use %p to format pointers, %lx to format unsigned longs.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
The extra definition for BITS_PER_LONG we had is also indirectly provided
by <asm-generic/types.h>, via <asm-generic/int-ll64.h> and
<asm/bitsperlong.h>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull fpu state cleanups from Ingo Molnar:
"This tree streamlines further aspects of FPU handling by eliminating
the prepare_to_copy() complication and moving that logic to
arch_dup_task_struct().
It also fixes the FPU dumps in threaded core dumps, removes and old
(and now invalid) assumption plus micro-optimizes the exit path by
avoiding an FPU save for dead tasks."
Fixed up trivial add-add conflict in arch/sh/kernel/process.c that came
in because we now do the FPU handling in arch_dup_task_struct() rather
than the legacy (and now gone) prepare_to_copy().
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: drop the fpu state during thread exit
x86, xsave: remove thread_has_fpu() bug check in __sanitize_i387_state()
coredump: ensure the fpu state is flushed for proper multi-threaded core dump
fork: move the real prepare_to_copy() users to arch_dup_task_struct()
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
TIF_NOTIFY_RESUME added (as bit 5). That way nommu glue needs no changes at
all; mmu one needs just to replace jmi do_signal_return to jne do_signal_return
There we have flags shifted up, until bit 6 (SIGPENDING) is in MSBit; instead
of checking that MSBit is set (jmi) we check that MSBit or something below it
is set (jne); bits 0..4 are never set, so that's precisely "bit 6 or bit 5 is
set".
Usual handling of NOTIFY_RESUME/SIGPENDING is done in do_notify_resume(); glue
calls it instead of do_signal().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate code
across architectures. In the past some architectures got this code wrong,
so using this helper function should stop that from happening again.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
guts of saved_sigmask-based sigsuspend/rt_sigsuspend. Takes
kernel sigset_t *.
Open-coded instances replaced with calling it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Pull m68knommu tree from Greg Ungerer:
"More merge and clean up of MMU and non-MMU common files, namely
signal.c and dma.c. There is also a simplification of the ColdFire
GPIO setup tables. Using a couple of simple macros we make the init
tables really small and easy to read, and save a couple of thousand
lines of code. Also a move of all the ColdFire subarch support files
into the existing coldfire directory. The sub-directories just ended
up duplicating Makefiles and now only contain really simple pieces of
code. This saves quite a few lines of code too.
As always a couple of bugs fixes thrown in too. Oh and a new
defconfig for the ColdFire platforms that support having the MMU
enabled."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (39 commits)
m68k: add a defconfig for the M5475EVB ColdFire with MMU board
m68knommu: unaligned.h fix for M68000 core
m68k: merge the MMU and non-MMU versions of the arch dma code
m68knommu: reorganize the no-MMU cache flushing to match m68k
m68knommu: move the 54xx platform code into the common ColdFire code directory
m68knommu: move the 532x platform code into the common ColdFire code directory
m68knommu: move the 5407 platform code into the common ColdFire code directory
m68knommu: move the 5307 platform code into the common ColdFire code directory
m68knommu: move the 528x platform code into the common ColdFire code directory
m68knommu: move the 527x platform code into the common ColdFire code directory
m68knommu: move the 5272 platform code into the common ColdFire code directory
m68knommu: move the 5249 platform code into the common ColdFire code directory
m68knommu: move the 523x platform code into the common ColdFire code directory
m68knommu: move the 520x platform code into the common ColdFire code directory
m68knommu: move the 5206 platform code into the common ColdFire code directory
m68knommu: simplify the ColdFire 5407 GPIO struct setup
m68knommu: simplify the ColdFire 532x GPIO struct setup
m68knommu: simplify the ColdFire 5307 GPIO struct setup
m68knommu: simplify the ColdFire 528x GPIO struct setup
m68knommu: simplify the ColdFire 527x GPIO struct setup
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Setup CROSS_COMPILE at the top
m68k: Correct the Atari ALLOWINT definition
m68k/video: Create <asm/vga.h>
m68k: Make sure {read,write}s[bwl]() are always defined
m68k/mm: Port OOM changes to do_page_fault()
scsi/atari: Make more functions static
scsi/atari: Revive "atascsi=" setup option
net/ariadne: Improve debug prints
m68k/atari: Change VME irq numbers from unsigned long to unsigned int
m68k/amiga: Use arch_initcall() for registering platform devices
m68k/amiga: Add error checks when registering platform devices
m68k/amiga: Mark z_dev_present() __init
m68k: Remove unused MAX_NOINT_IPL definition
Add a default configuration for the newly supported ColdFire CPUs running
with MMU enabled. This is based on Freescales own M5475EVB demo board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch fixes unaligned memory access for the 68000 core based cpu's.
Some time ago, my cpu (68000) was raising address/bus error's when mounting
cifs shares (didn't bother to debug it at the time). After developing the
MMC/SD card driver I was having the same issue when mounting the vfat fs.
I've traced the issue down to the 'unaligned.h' file. (I guess nobody has
ever used unaligned.h back in the 68328 'era'.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The majority of the m68k architecture dma code is the same, so merge the
current separated files dma_no.c and dma_mm.c back into a single dma.c
The main alloc and free routines are a little different, so we keep a
single #ifdef based on CONFIG_MMU for them. All the other support functions
are now identical.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Introduce cache_push() and cache_clear() functions for the non-MMU m68k
devices. With these in place we can more easily merge some of the common
m68k arch code.
In particular by reorganizing the __flush_cache_all() code and separating
the cache push and clear functions it becomes trivial to implement the
new cache_push() and cache_clear() functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The code that adds each ColdFire platforms GPIO signals is duplicated in
each platforms specific code. Remove it from each platforms code and put
a single version in the existing ColdFire gpio subsystem init code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
We also need to rename some of the GPIO registers to be consistent with
all other ColdFire parts (we can't use the new GPIO macros otherwise).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
We have very large tables in the ColdFire CPU GPIO setup code that essentially
boil down to 2 distinct types of GPIO pin initiaization. Using 2 macros we can
reduce these large tables to at most a dozen lines of setup code, and in quite
a few cases a single table entry.
Introduce these 2 macros into the existing mcfgpio.h header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
This patch removes the following warning:
fs/binfmt_flat.c:752: warning: unused variable 'persistent'.
There is neither functionality change, nor extra code generated.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MMU (signal_mm.c) and non-MMU (signal_no.c) versions of the m68k
architecture signal handling code are very similar. Most of their code is
the same.
Merge the two back into a single signal.c, and move some of the code around
inside the file to minimize the number of #ifdefs required. Specificially
we can group out the CONFIG_FPU and the CONFIG_MMU code. We end up needing
a few other "#ifdef CONFIG_MMU" as well, but not too many.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
That old mail address doesnt exist any more.
This changes all occurences to a current address.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Acked-by: Sebastian Heß <shess@hessware.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
CROSS_COMPILE must be setup before using e.g. cc-option (and a few other
as-*, cc-*, ld-* macros), else they will check against the wrong compiler
when cross-compiling, and may invoke the cross compiler with wrong or
suboptimal compiler options.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.
This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.
For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this. Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Enable Coldfire QSPI support when SPI_COLDFIRE_QSPI is built as a module.
This version of the patch combines changes to the config files and device.c
and uses IF_ENABLED (thanks to Sam Ravnborg for the suggestion).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer