r8168_check_dash() returns false anyway for all chip versions not
supporting dash. So we can simplify the check conditions.
In addition change the check functions to return bool instead of int,
because they actually return a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if BIOS enables WOL in the chip, settings are inconsistent
because the device isn't marked as wakeup-enabled (if not done
explicitly via userspace tools). This causes issues with suspend/
resume because mdio_bus_phy_may_suspend() checks whether device is
wakeup-enabled. In detail MDIO bus access in phy_suspend() can fail
because the MDIO bus is disabled.
In the history of the driver we find two competing approaches:
8f9d513803 "r8169: remember WOL preferences on driver load" prefers
to preserve what the BIOS may have set, whilst bde135a672
"r8169: only enable PCI wakeups when WOL is active" disabled PCI
wakeup per default to work around a bug on one platform.
Seems like nobody complained after the latter patch about non-working
WOL, what makes me think that nobody uses WOL w/o configuring it
explicitly.
My opinion:
Vast majority of users doesn't use WOL even if the BIOS enables it in
the chip. And having WOL being active keeps the PHY(s) from powering
down if being idle.
If somebody needs WOL, he can enable it during boot, e.g. by
configuring systemd.link/WakeOnLan.
Therefore, to make WOL consistent again, disable it per default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMDA0099-0001 platform can support the 1x10G + 1x25G mixed mode
operation. Recently, firmware has been added for this configuration
mode.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach of one counter to rule them all when tracking the number
of active sub-crqs, pools, and napi has problems handling some failover
scenarios. This is due to the split in initializing the sub crqs,
pools and napi in different places and the placement of updating
the active counts.
This patch simplifies this by having a counter for tx and rx
sub-crqs, pools, and napi.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change, transmissions that only needed
one descriptor were being missed. The result is that such
packets were tracked as outstanding transmissions but never
removed when its completion notification was received.
Fixes: ffc385b95a ("ibmvnic: Keep track of supplementary TX descriptors")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.
Fixes: 34f0f4e3f4 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.
Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes shared code updates for mlx5 core driver for both
netdev and rdma subsystems.
By Saeed,
First six patches of the series are meant to address a performance issue
and should provide a performance boost for multi core IRQ interrupt hungry
workloads. The issue is fixed in the first patch, all other patches are
meant to refactor the code in light of this fix.
The problem it comes to fix, is a shared spinlock accessed across all HCA
IRQs which protects the CQ database. To solve this we simply move the CQ
database and its spinlock to be per EQ (IRQ), thus per core.
By Yonatan,
Fragmented completion queue (CQ) for RDMA,
core driver implementation to create fragmented CQ buffers rather than
one large contiguous memory buffer, the implementation scheme already
exist and used by the netdev CQs, the patch shares that code with the
rdma CQ creation flow and makes use of the new API in mlx5_ib driver.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJajcwxAAoJEEg/ir3gV/o+uJAIAICP2LBu5ANBgX7Z7/B0IZX4
Abkfk+IKR44v+3t0BBgEAZI2A9LcTQ8pwIOeLCDpcKd78665Y7rYQL1p31WuPKc5
1WwwBesjQLAmdiNLIjUnjW1fd3YyOmqLBcaMMYIeF0m4m4pCQue1kwtxesQrhdZV
I7FBxxnQt/8o6hoh/5nmU4DzGyZaY+uR/4FxUCEreklfhNeI5M2DZKe1xQCmhsJ4
Tosh/cJ8kSBJfclH6hk1lh5eWGDYDltWCpY86KBWsYktl10VAE3P7LPmekn487ta
e6cL1NPoEHbp+/UBThkNZMzUnA7wpoNeDbTTtVZrdcL1KivwColt1r3pmS1bqEQ=
=DlfW
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-21' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-21
This series includes shared code updates for mlx5 core driver for both
netdev and rdma subsystems.
By Saeed,
First six patches of the series are meant to address a performance issue
and should provide a performance boost for multi core IRQ interrupt hungry
workloads. The issue is fixed in the first patch, all other patches are
meant to refactor the code in light of this fix.
The problem it comes to fix, is a shared spinlock accessed across all HCA
IRQs which protects the CQ database. To solve this we simply move the CQ
database and its spinlock to be per EQ (IRQ), thus per core.
By Yonatan,
Fragmented completion queue (CQ) for RDMA,
core driver implementation to create fragmented CQ buffers rather than
one large contiguous memory buffer, the implementation scheme already
exist and used by the netdev CQs, the patch shares that code with the
rdma CQ creation flow and makes use of the new API in mlx5_ib driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After resuming from suspend, the PCI device support must re-enable the
interrupt setting so that interrupts are actually delivered.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a failure occurs during initialization of the tx sub crq
irqs, we should branch to the cleanup of the tx irqs. The current
code branches to the rx irq cleanup and attempts to cleanup the
rx irqs which have not been initialized.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJajJahAAoJEEg/ir3gV/o+PTQIALd4/l5VEU1vWqXp6PPaIaRP
fCt4CKXkeIozyOhkiaYLcNAvPnsJRi54a/PGyUbHwxadkjuOhS8WETyQwMf8gbKF
g+LTDseqKjWcu6fUMqe7TmjrNHSo2VErjOjHw1+7emKSkBZuc8zBBND9PqHtOQY6
f1KoUY6IBs22dwqzynxkC5A62VQbTYd0FPnf1n9wN8ubFXSb37KUgKoW4kmMFmLe
JsYEcsAKxpfepnP+EYLyDrVcT1LA9edi5DI5uxSfNgas6bTtjRPhtyZCznDF8rly
jEWv3O2c+HhchuysoACTLiTllviHGj0Myv+rGb0ouhjZWMtulgPPQ04lbYjjr84=
=uF0v
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-02-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-02-20
The following pull request includes some fixes for the mlx5 core and
netdevice driver.
Please pull and let me know if there's any issue.
-stable 4.10.y:
('net/mlx5e: Fix loopback self test when GRO is off')
-stable 4.12.y:
('net/mlx5e: Specify numa node when allocating drop rq')
-stable 4.13.y:
('net/mlx5e: Verify inline header size do not exceed SKB linear size')
-stable 4.15.y:
('net/mlx5e: Fix TCP checksum in LRO buffers')
('net/mlx5: Fix error handling when adding flow rules')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid losing any stats when the number of sub-crqs change, allocate
the max number of stats buffers so a stats buffer exists all possible
sub-crqs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to handle the number of rx sub crqs changing during a driver
reset, the ibmvnic driver also needs to update the number of napi.
To do this the code to init and free napi's is moved to their own
routines so they can be called during the reset process.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver resets it is possible that the number of tx/rx
sub-crqs can change. This patch handles this so that the driver does
not try to access non-existent sub-crqs.
The count for releasing sub crqs depends on the adapter state. The
active queue count is not set in probe, so if we are relasing in probe
state we use the request queue count.
Additionally, a parameter is added to release_sub_crqs() so that
we know if the h_call to free the sub-crq needs to be made. In
the reset path we have to do a reset of the main crq, which is
a free followed by a register of the main crq. The free of main
crq results in all of the sub crq's being free'ed. When updating
sub-crq count in the reset path we do not want to h_free the
sub-crqs, they are already free'ed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inpreparation for using the active scrq count to track more active
resources, move the setting of the active count to after initialization
occurs in initial driver init and during driver reset.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tx/rx active pool variables to be tx/rx active scrq
counts. The tx/rx pools are per sub-crq so this is a more appropriate
name. This also is a preparatory step for using thiese variables
for handling updates to sub-crqs and napi based on the active
count.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_foo() to log the slot number instead of the unexpanded "eth%d"
format string.
Disambiguate the two identical "Card type %s is unsupported" messages.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves an old bug that constrained this driver to no more than
one card.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lib8390 module parameter 'msg_enable' doesn't do anything useful:
it causes an ancient version string to be logged.
Remove redundant code that logs the same string.
In ne.c and wd.c, the value of ei_local->msg_enable is used before
being assigned. Use ne_msg_enable and wd_msg_enable, respectively.
Most of the other 8390 drivers never assign ei_local->msg_enable.
Use the 'msg_enable' module parameter from lib8390 as the default
value.
Eliminate the pointless static and local variables.
Clean up an indentation mistake.
All of these issues originated from the same patch.
Cc: Russell King <linux@armlinux.org.uk>
Fixes: c45f812f02 ("8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hydra, zorro8390 and mcf8390 drivers all #include "lib8390.c" and
have no need for 8390.o. modinfo confirms no dependency on 8390.ko.
Drop the redundant dependency from the Makefile. objdump confirms
that this patch has no effect on the module binaries.
The superfluous additions of 8390.o were introduced in
commit 644570b830 ("8390: Move the 8390 related drivers").
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_init_phy() resets the PHY anyway after applying the chip-specific
PHY configuration. So we don't need to soft-reset the PHY as part of the
chip-specific configuration.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bde135a672 "r8169: only enable PCI wakeups when WOL is active"
removed the only user of flag RTL_FEATURE_WOL. So let's remove some
now dead code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If building match list or adding existing fg fails when
node is locked, function returned without unlocking it.
This happened if node version changed or adding existing fg
returned with EAGAIN after jumping to search_again_locked label.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
First use of drop counters happens in esw_apply_vport_conf function,
while they are allocated later in the flow. Fix that by moving
esw_vport_create_drop_counters function to be called before the first use.
Fixes: b8a0dbe3a9 ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can't allow only some of the rules sharing an FTE to ask for
header re-write, add it to the conflicting action checks.
Fixes: 0d235c3fab ('net/mlx5: Add hash table to search FTEs in a flow-group')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The adapter uses the cache_line_128byte setting to set the bounds for
end padding. On systems where the cacheline size is greater than 128B
use 128B instead of the default of 64B. This results in fewer partial
cacheline writes. There's a 50% chance it will pad to the end of a 256B
cache line vs only 25% when using 64B.
Fixes: f32f5bd2eb ("net/mlx5: Configure cache line size for start and end padding")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When allocating a drop rq, no numa node is explicitly set which means
allocations are done on node zero. This is not necessarily the nearest
numa node to the HCA, and even worse, might even be a memoryless numa
node.
Choose the numa_node given to us by the pci device in order to properly
allocate the coherent dma memory instead of assuming zero is valid.
Fixes: 556dd1b9c3 ("net/mlx5e: Set drop RQ's necessary parameters only")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This isn't supported when we emulate eswitch vlan push action which
is the current state of things.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix these gcc warnings on drivers/net/ethernet/mellanox/mlx5:
[..]/core/lib/clock.c:454:6: warning: no previous prototype for 'mlx5_init_clock' [-Wmissing-prototypes]
[..]/core/lib/clock.c:510:6: warning: no previous prototype for 'mlx5_cleanup_clock' [-Wmissing-prototypes]
[..]/core/en_main.c:3141:5: warning: no previous prototype for 'mlx5e_setup_tc' [-Wmissing-prototypes]
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver tries to copy at least MLX5E_MIN_INLINE bytes into the control
segment of the WQE. It assumes that the linear part contains at least
MLX5E_MIN_INLINE bytes, which can be wrong.
Cited commit verified that driver will not copy more bytes into the
inline header part that the actual size of the packet. Re-factor this
check to make sure we do not exceed the linear part as well.
This fix is aligned with the current driver's assumption that the entire
L2 will be present in the linear part of the SKB.
Fixes: 6aace17e64 ("net/mlx5e: Fix inline header size for small packets")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When GRO is off, the transport header pointer in sk_buff is
initialized to network's header.
To find the udp header, instead of using udp_hdr() which assumes
skb_network_header was set, manually calculate the udp header offset.
Fixes: 0952da791c ("net/mlx5e: Add support for loopback selftest")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When receiving an LRO packet, the checksum field is set by the hardware
to the checksum of the first coalesced packet. Obviously, this checksum
is not valid for the merged LRO packet and should be fixed. We can use
the CQE checksum which covers the checksum of the entire merged packet
TCP payload to help us calculate the checksum incrementally.
Tested by sending IPv4/6 traffic with LRO enabled, RX checksum disabled
and watching nstat checksum error counters (in addition to the obvious
bandwidth drop caused by checksum errors).
This bug is usually "hidden" since LRO packets would go through the
CHECKSUM_UNNECESSARY flow which does not validate the packet checksum.
It's important to note that previous to this patch, LRO packets provided
with CHECKSUM_UNNECESSARY are indeed packets with a correct validated
checksum (even though the checksum inside the TCP header is incorrect),
since the hardware LRO aggregation is terminated upon receiving a packet
with bad checksum.
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
After introduction of commit d0869c0071, there were some instances of
RX queue entries from a previous session (before the device was closed
and reopened) returned to the NAPI polling routine. Since the corresponding
socket buffers were freed, this resulted in a panic on reopen. Include
a check for a NULL skb here to avoid this.
Fixes: d0869c0071 ("ibmvnic: Clean RX pool buffers during device close")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Honor error code from stmmac_dt_phy() instead of always
returning -ENODEV.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree binding for stmmac says:
- Multiple TX Queues parameters: below the list of all the parameters to
configure the multiple TX queues:
- snps,tx-queues-to-use: number of TX queues to be used in the driver
[...]
- For each TX queue
[...]
However, if one specifies snps,tx-queues-to-use = 2,
but omits the queue subnodes, or defines just one queue subnode,
since the driver appears to initialize queues with sane default
values, we will get tx queue timeouts.
This is because the initialization code only initializes
as many queues as it finds subnodes. Potentially leaving
some queues uninitialized.
To avoid hard to debug issues, return an error if the number
of subnodes differ from snps,tx-queues-to-use/snps,rx-queues-to-use.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_mac_config_rx_queues_routing() incorrectly calls rx_queue_prio()
instead of rx_queue_routing().
This looks like a copy paste issue, since
stmmac_mac_config_rx_queues_prio() already calls rx_queue_prio(),
and both stmmac_mac_config_rx_queues_routing() and
stmmac_mac_config_rx_queues_prio() are very similar in structure.
Fixes: abe80fdc6e ("net: stmmac: RX queue routing configuration")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at dwmac4_tx_queue_routing(), it is obvious that it
sets up rx queue routing.
Rename dwmac4_tx_queue_routing() to dwmac4_rx_queue_routing()
to better match reality.
Fixes: abe80fdc6e ("net: stmmac: RX queue routing configuration")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that a tx_skbuff entry has been cleared
by stmmac_tx_clean() before stmmac_xmit()/stmmac_tso_xmit()
assigns a new skb to that entry. However, since we never check
the current value before overwriting it, it is theoretically
possible that a non-NULL value is overwritten.
Add WARN_ONs to verify that each entry in tx_skbuff is NULL
before it is assigned a new value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_skbuff is initialized to NULL in init_dma_tx_desc_rings(), which is
called from ndo_open().
stmmac_tx_clean() frees any non-NULL skb, and sets the tx_skbuff
entry to NULL. Hence, there is no need to set skbuff entries to NULL
in stmmac_xmit()/stmmac_tso_xmit(), and doing so falsely gives the
reader the impression that it is needed.
Do not clear tx_skbuff entries in stmmac_xmit()/stmmac_tso_xmit().
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA engine in dwmac4 can segment a large TSO packet to several
smaller packets of (max) size Maximum Segment Size (MSS).
The DMA engine fetches and saves the MSS via a context descriptor.
This context decriptor has to be provided to each tx DMA channel.
To ensure that this is done, move struct member mss from stmmac_priv
to stmmac_tx_queue.
stmmac_reset_queues_param() now also resets mss, together with other
queue parameters, so reset of mss value can be removed from
stmmac_resume().
init_dma_tx_desc_rings() now also resets mss, together with other
queue parameters, so reset of mss value can be removed from
stmmac_open().
This fixes tx queue timeouts for dwmac4, with DT property
snps,tx-queues-to-use > 1, when running iperf3 with multiple threads.
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for calculating occupancy for separate kvdl parts.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dynamic partition set via the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linear part of the KVD memory is sub-divided into multiple parts. This
patch exposes this internal partitions via the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding size validation logic into core cleanup is required.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller