We used to reset last_adj to 0 on crossing a power domain boundary, to
slow down our rate of change. However, commit 60548c554b ("drm/i915:
Interactive RPS mode") accidentally caused it to be reset on every
frequency update, nerfing the fast response granted by the slow start
algorithm.
Fixes: 60548c554b ("drm/i915: Interactive RPS mode")
Testcase: igt/pm_rps/mix-max-config-loaded
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802100631.31305-1-chris@chris-wilson.co.uk
RPS provides a feedback loop where we use the load during the previous
evaluation interval to decide whether to up or down clock the GPU
frequency. Our responsiveness is split into 3 regimes, a high and low
plateau with the intent to keep the gpu clocked high to cover occasional
stalls under high load, and low despite occasional glitches under steady
low load, and inbetween. However, we run into situations like kodi where
we want to stay at low power (video decoding is done efficiently
inside the fixed function HW and doesn't need high clocks even for high
bitrate streams), but just occasionally the pipeline is more complex
than a video decode and we need a smidgen of extra GPU power to present
on time. In the high power regime, we sample at sub frame intervals with
a bias to upclocking, and conversely at low power we sample over a few
frames worth to provide what we consider to be the right levels of
responsiveness respectively. At low power, we more or less expect to be
kicked out to high power at the start of a busy sequence by waitboosting.
Prior to commit e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active
request") whenever we missed the frame or stalled, we would immediate go
full throttle and upclock the GPU to max. But in commit e9af4ea2b9, we
relaxed the waitboosting to only apply if the pipeline was deep to avoid
over-committing resources for a near miss. Sadly though, a near miss is
still a miss, and perceptible as jitter in the frame delivery.
To try and prevent the near miss before having to resort to boosting
after the fact, we use the pageflip queue as an indication that we are
in an "interactive" regime and so should sample the load more frequently
to provide power before the frame misses it vblank. This will make us
more favorable to providing a small power increase (one or two bins) as
required rather than going all the way to maximum and then having to
work back down again. (We still keep the waitboosting mechanism around
just in case a dramatic change in system load requires urgent uplocking,
faster than we can provide in a few evaluation intervals.)
v2: Reduce rps_set_interactive to a boolean parameter to avoid the
confusion of what if they wanted a new power mode after pinning to a
different mode (which to choose?)
v3: Only reprogram RPS while the GT is awake, it will be set when we
wake the GT, and while off warns about being used outside of rpm.
v4: Fix deferred application of interactive mode
v5: s/state/interactive/
v6: Group the mutex with its principle in a substruct
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107111
Fixes: e9af4ea2b9 ("drm/i915: Avoid waitboosting on the active request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731132629.3381-1-chris@chris-wilson.co.uk
According to intel_read_wm_latency() it is perfectly legal for one WM
and all subsequent levels to be 0 (and the deeper powersaving states
disabled), so don't shout *ERROR*, over and over again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726161527.10516-1-chris@chris-wilson.co.uk
While things may have been different before, right now the function is
very simple and has a single caller. IMHO any possible benefits from
an abstraction here are gone and not worth the price of the current
indirection while reading the code.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180607230700.28359-1-paulo.r.zanoni@intel.com
Do not update number of enabled dbuf slices in dev_priv struct until we
actually enable/disable dbuf slice in hw. This is leading to never
updating dbuf slices and resulting in DBuf slice mismatch warning.
Fixes: aa9664ffe8 ("drm/i915/icl: Enable 2nd DBuf slice only when needed")
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517132626.5885-1-mahesh1.kumar@intel.com
Sampler Dynamic Frequency Rebalancing (DFR) aims to reduce Sampler
power by dynamically changing its clock frequency in low-throughput
conditions. This patches enables it by default on Gen11.
v2: Wrong operation to clear the bit (Praveen)
v3: Rebased on top of the WA refactoring
v4: Move to icl_init_clock_gating, since it's not a WA (Rodrigo)
v5: C, not lisp (Chris)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Praveen Paneri <praveen.paneri@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-3-git-send-email-oscar.mateo@intel.com
Inherit workarounds from previous platforms that are still valid for
Icelake.
v2: GEN7_ROW_CHICKEN2 is masked
v3:
- Since it has been fixed already in upstream, removed the TODO
comment about WA_SET_BIT for WaInPlaceDecompressionHang.
- Squashed with this patch:
drm/i915/icl: add icelake_init_clock_gating()
from Paulo Zanoni <paulo.r.zanoni@intel.com>
- Squashed with this patch:
drm/i915/icl: WaForceEnableNonCoherent
from Oscar Mateo <oscar.mateo@intel.com>
- WaPushConstantDereferenceHoldDisable is now Wa_1604370585 and
applies to B0 as well.
- WaPipeControlBefore3DStateSamplePattern WABB was being applied
to ICL incorrectly.
v4:
- Wrap the commit message
- s/dev_priv/p to please checkpatch
v5: Rebased on top of the WA refactoring
v6: Rebased on top of further whitelist registers refactoring (Michel)
v7: Added WaRsForcewakeAddDelayForAck
v8: s/ICL_HDC_CHICKEN0/ICL_HDC_MODE (Mika)
v9:
- C, not lisp (Chris)
- WaIncreaseDefaultTLBEntries is the same for GEN > 9_LP (Tvrtko)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1525814984-20039-2-git-send-email-oscar.mateo@intel.com
Gen11/ICL onward ddb entry start/end mask is increased from 10 bits to
11 bits. This patch make changes to use proper mask for ICL+ during
hardware ddb value readout.
Changes since V1:
- Use _MASK & _SHIFT macro (James)
Changes since V2:
- use kernel type u8 instead of uint8_t
Changes since V3:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-4-mahesh1.kumar@intel.com
ICL has two slices of DBuf, each slice of size 1024 blocks.
We should not always enable slice-2. It should be enabled only if
display total required BW is > 12GBps OR more than 1 pipes are enabled.
Changes since V1:
- typecast total_data_rate to u64 before multiplication to solve any
possible overflow (Rodrigo)
- fix where skl_wm_get_hw_state was memsetting ddb, resulting
enabled_slices to become zero
- Fix the logic of calculating ddb_size
Changes since V2:
- If no-crtc is part of commit required_slices will have value "0",
don't try to disable DBuf slice.
Changes since V3:
- Create a generic helper to enable/disable slice
- don't return early if total_data_rate is 0, it may be cursor only
commit, or atomic modeset without any plane.
Changes since V4:
- Solve checkpatch warnings
- use kernel types u8/u64 instead of uint8_t/uint64_t
Changes since V5:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-3-mahesh1.kumar@intel.com
This patch adds support to start tracking status of DBUF slices.
This is foundation to introduce support for enabling/disabling second
DBUF slice dynamically for ICL.
Changes Since V1:
- use kernel type u8 over uint8_t
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-2-mahesh1.kumar@intel.com
This patch splits skl_compute_wm/ddb functions into two parts.
One adds all affected pipes after the commit to atomic_state structure
and second part does compute the DDB.
v2: Added reviewed by tag from Shashank Sharma
v3: Added reviewed by from Juha-Pekka Heikkila
v4: Rebased the series
v5: Fixed checkpatch error. Changed *changed = true
to (*changed) = true;
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-10-git-send-email-vidya.srinivas@intel.com
Display Workaround #0826 (SKL:ALL BXT:ALL) & #1059(CNL:A)
Hardware sometimes fails to wake memory from pkg C states fetching the
last few lines of planar YUV 420 (NV12) planes. This causes
intermittent underflow and corruption.
WA: Disable package C states or do not enable latency levels 1 through 7
(WM1 - WM7) on NV12 planes.
v2: Addressed review comments by Maarten.
v3: Adding reviewed by tag from Shashank Sharma
v4: Added reviewed by from Juha-Pekka Heikkila
v5: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-9-git-send-email-vidya.srinivas@intel.com
DDB allocation optimization algorithm requires/assumes ddb allocation for
any memory C-state level DDB value to be as high as level below the
current level. Render decompression requires level WM to be as high as
wm level-0. This patch fulfils both the requirements.
v2: Changed plane_num to plane_id in skl_compute_wm_levels
v3: Addressed review comments from Shashank Sharma
Changed the commit message "statement can be more clear,
"DDB value to be as high as level below " what is level below ?"
v4: Added reviewed by tag from Shashank Sharma
v5: Added reviewed by from Juha-Pekka Heikkila
v6: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-8-git-send-email-vidya.srinivas@intel.com
This patch passes skl_wm_level structure itself to watermark
computation function skl_compute_plane_wm function (instead
of its internal parameters). It reduces number of arguments
required to be passed.
v2: Addressed review comments by Shashank Sharma
v3: Adding reviewed by tag from Shashank Sharma
v4: Added reviewed by from Juha-Pekka Heikkila
v5: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-7-git-send-email-vidya.srinivas@intel.com
NV12 requires WM calculation for UV plane as well.
UV plane WM should also fulfill all the WM related restrictions.
v2: Addressed review comments from Shashank Sharma.
v3: Addressed review comments from Shashank Sharma
Changed plane_num to plane_id in skl_compute_plane_wm_params
and skl_compute_plane_wm.
Adding reviewed by tag from Shashank Sharma
v4: Added reviewed by from Juha-Pekka Heikkila
v5: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-6-git-send-email-vidya.srinivas@intel.com
For YUV 420 Planar formats like NV12,
buffer allocation is done for Y and UV surfaces separately.
For NV12 plane formats, the UV buffer
allocation must be programmed in the Plane Buffer Config register
and the Y buffer allocation must be programmed in the
Plane NV12 Buffer Config register. Both register values
should be verified during verify_wm_state.
v2: Addressed review comments by Maarten.
v3: Addressed review comments by Shashank Sharma.
v4: Adding reviewed by tag from Shashank Sharma
v5: Added reviewed by from Juha-Pekka Heikkila
v6: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-5-git-send-email-vidya.srinivas@intel.com
Current code calculates DDB for planar formats in such a way that we
store DDB of plane-0 in plane 1 & vice-versa.
In order to make this clean this patch refactors WM/DDB calculation for
NV12 planar formats.
v2: Addressed review comments by Maarten
v3: Rebased and addressed review comments by Maarten
v4: Fixed a compilation issue of string replacement is_nv12 to
is_planar
v5: Added reviewed by from Juha-Pekka Heikkila
v6: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-3-git-send-email-vidya.srinivas@intel.com
skl_wm_values struct contains values of pipe/plane DDB only.
so rename it for better readability of code. Similarly
skl_copy_wm_for_pipe copies DDB values.
s/skl_wm_values/skl_ddb_values
s/skl_copy_wm_for_pipe/skl_copy_ddb_for_pipe
Changes since V1:
- also change name of skl_copy_wm_for_pipe
v2: Added reviewed by from Juha-Pekka Heikkila
v3: Rebased the series
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523245273-30264-2-git-send-email-vidya.srinivas@intel.com
AFAICT, once the new interrupt is in place, the rest should behave the
same as Gen10.
v2: Update ring frequencies (Sagar)
v3: Rebase.
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-5-mika.kuoppala@linux.intel.com
Using the new hierarchical interrupt infrastructure.
v2: Rebase
v3: Rebase
v4: use class/instance handler (Mika)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405140052.10682-3-mika.kuoppala@linux.intel.com
Looping through rps frequencies when both min and max are zero
ends up into an endless loop. This can happen during hardware
enablement.
Bail out early if rps frequencies are not correctly set yet.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320151734.11761-1-mika.kuoppala@linux.intel.com
When reporting the frequency table stored in the punit, report the full
range and not just the user restricted frequency range. In the process
keep the code to set the frequency table and read it the same.
v3: As we haven't separated the sb_lock from the pcu_lock yet, there's a
cycle between the pcu_lock and intel_runtime_pm_get.
References: f936ec34de ("drm/i915/skl: Updated the i915_ring_freq_table debugfs function")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20180308142648.4016-2-chris@chris-wilson.co.uk
"Clock gating bug in GWL may not clear barrier state when an EOT
is received, causing a hang the next time that barrier is used."
HSDES: 2201832410
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307220912.3681-1-rodrigo.vivi@intel.com
No functional change since WA is already applied.
But since it has different names on different databases,
let's document it here to avoid future confusion.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306012812.19779-1-rodrigo.vivi@intel.com
No functional change. WA is already properly applied.
but in different databases it has different names.
Let's document all of them to avoid future confusion.
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306012000.18928-1-rodrigo.vivi@intel.com
v2: Rebase.
v3:
* Remove DPF, it has been removed from SKL+.
* Fix -internal rebase wrt. execlists interrupt handling.
v4: Rebase.
v5:
* Updated for POR changes. (Daniele Ceraolo Spurio)
* Merged with irq handling fixes by Daniele Ceraolo Spurio:
* Simplify the code by using gen8_cs_irq_handler.
* Fix interrupt handling for the upstream kernel.
v6:
* Remove early bringup debug messages (Tvrtko)
* Add NB about arbitrary spin wait timeout (Tvrtko)
v7 (from Paulo):
* Don't try to write RO bits to registers.
* Don't check for PCH types that don't exist. PCH interrupts are not
here yet.
v9:
* squashed in selector and shared register handling (Daniele)
* skip writing of irq if data is not valid (Daniele)
* use time_after32 (Chris)
* use I915_MAX_VCS and I915_MAX_VECS (Daniele)
* remove fake pm interrupt handling for later patch (Mika)
v10:
* Direct processing of banks. clear banks early (Chris)
* remove poll on valid bit, only clear valid bit (Mika)
* use raw accessors, better naming (Chris)
v11:
* adapt to raw_reg_[read|write]
* bring back polling the valid bit (Daniele)
v12:
* continue if unset intr_dw (Daniele)
* comment the usage of gen8_de_irq_handler bits (Daniele)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180228101153.7224-2-mika.kuoppala@linux.intel.com
Old Wa added now forever on CNL all steppings.
With CPU P states enabled along with RC6, dispatcher
hangs can happen.
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222200535.9290-1-rodrigo.vivi@intel.com
We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)
In short, the spatch:
@@
@@
- struct drm_i915_gem_request
+ struct i915_request
A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
clang spots
drivers/gpu/drm/i915/intel_pm.c:4655:6: warning: variable 'trans_min' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (INTEL_GEN(dev_priv) >= 10)
but fortunately for us we skip the function unless on a gen10+ device.
However, to keep the function generic in case we do want to re-enable it
for gen9 again, initialise trans_min to 0.
References: ca47667f52 ("drm/i915/gen10: Calculate and enable transition WM")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115105036.1094-3-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
drivers/gpu/drm/i915/intel_pm.c:750: warning: Function parameter or member 'fifo_size' not described in 'intel_calculate_wm'
drivers/gpu/drm/i915/intel_pm.c:5900: warning: Function parameter or member 'crtc' not described in 'intel_update_watermarks'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214140303.1561-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We can implement limited RC6 counter wrap-around protection under the
assumption that clients will be reading this value more frequently than
the wrap period on a given platform.
With the typical wrap-around period being ~90 minutes, even with the
exception of Baytrail which wraps every 13 seconds, this sounds like a
reasonable assumption.
Implementation works by storing a 64-bit software copy of a hardware RC6
counter, along with the previous HW counter snapshot. This enables it to
detect wrap is polled frequently enough and keep the software copy
monotonically incrementing.
v2:
* Missed GEN6_GT_GFX_RC6_LOCKED when considering slot sizing and
indexing.
* Fixed off-by-one in wrap-around handling. (Chris Wilson)
v3:
* Simplify index checking by using unsigned int. (Chris Wilson)
* Expand the comment to explain why indexing works.
v4:
* Use __int128 if supported.
v5:
* Use mul_u64_u32_div. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94852
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v3
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208160036.29919-1-tvrtko.ursulin@linux.intel.com
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
According to bspec, result_lines > 31 is only a maximum for latency
level 1 through 7.
For level 0 the number of lines is ignored, so always write 0 there
to prevent overflowing the 5 bits value.
This is required to make NV12 work.
Changes since v1:
- Rebase on top of GEN11 wm changes. It seems to use res_lines for
level 0 limit calculations, but still doesn't appear to program it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20180205105841.31634-1-maarten.lankhorst@linux.intel.com
There is no requirement for doing the PCODE request polling atomically,
so do that only for a short time switching to sleeping poll afterwards.
The specification requires a 150usec timeout for the change notification,
so let's use that for the atomic poll. Do the extra 2ms poll - needed as
a workaround on BXT/GLK - in sleeping mode.
v2:
- rebase on v2 of patchset dropping the sandybridge_pcode_read/write
refactoring (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-2-imre.deak@intel.com
Currently we see sporadic timeouts during CDCLK changing both on BXT and
GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by
changing the frequency in a tight loop after blanking the display. The
upper bound for the completion time is 800us based on my tests, so
increase it from the current 500us to 2ms; with that I couldn't trigger
the problem either on BXT or GLK.
Note that timeouts happened during both the change notification and the
voltage level setting PCODE request. (For the latter one BSpec doesn't
require us to wait for completion before further HW programming.)
This issue is similar to
commit 2c7d0602c8 ("drm/i915/gen9: Fix PCODE polling during CDCLK
change notification")
but there the PCODE request does complete (as shown by the mbox
busy flag), only the reply we get from PCODE indicates a failure.
So there we keep resending the request until a success reply, here we
just have to increase the timeout for the one PCODE request we send.
v2:
- s/snb_pcode_request/sandybridge_pcode_write_timeout/ (Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.4+
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com
We don't have planar pixel format support implemented for ICL yet.
ICL require 2 display planes to be allocated for Planar formats unlike
previous GEN. So ICL/GEN11 doesn't require to write Y-plane ddb data in
NV12_BUF_CFG register and PLANE_NV12_BUF_CFG register is removed in ICL.
This patch removes the PLANE_NV12_BUF_CFG write for ICL.
Changes Since V1:
- Improve commit message as per Paulo's comment
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-5-paulo.r.zanoni@intel.com
ICL require DDB allocation of plane to be more than "minimum display
buffer needed" for each level in order to enable WM level.
This patch implements and consider the same while allocating DDB
and enabling WM.
Changes Since V1:
- rebase
Changes Since V2:
- Remove extra parentheses
- Use FP16.16 only when absolutely necessary (Paulo)
Changes Since V3:
- Rebase
Changes since v4 (from Paulo):
- Coding style issue.
Changes since v5 (from Paulo):
- Do the final checks according to BSpec.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-4-paulo.r.zanoni@intel.com
GEN9/10 had fixed DBuf block size of 512. Dbuf block size is not a
fixed number anymore in GEN11, it varies according to bits per pixel
and tiling. If 8bpp & Yf-tile surface, block size = 256 else block
size = 512
This patch addresses the same.
v2 (from Paulo):
- Make it compile.
- Fix a few coding style issues.
v3:
- Rebase on top of upstream patches
v4 (from Paulo):
- Bikeshed if statements (James).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-3-paulo.r.zanoni@intel.com
GEN9 onwards bypass path allocation of 4 blocks was needed, as per
hardware design. ICL doesn't require bypass path allocation of 4 DDB
blocks, handling the same in this patch.
v2 (from Paulo):
- No need for a comment that says what the code already says.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130134918.32283-2-paulo.r.zanoni@intel.com
On gen9+, after an idle period the HW will disable the entire power well
to conserve power (by preventing current leakage). It takes around a 100
microseconds to bring the power well back online afterwards. With the
current hysteresis value of 25us (really 25 * 1280ns), we do not have
sufficient time to respond to an interrupt and schedule the next execution
before the HW powers itself down. (At present, we prevent this by
grabbing the forcewake for prolonged periods of time, but that overkill
fixed in the next patch.) The minimum we want to set the power gating
hysteresis to is the length of time it takes us to service the GPU, which
across a broad spectrum of machines is about 250us.
(Note this also brings guc latency into the same ballpark as execlists.)
v2: Include some notes on where I plucked the numbers from.
Testcase: igt/gem_exec_nop/sequential
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122135541.32222-1-chris@chris-wilson.co.uk
Keeps things consistent now that we make use of struct resource. This
should keep us covered in case we ever get huge amounts of stolen
memory.
v2: bunch of missing conversions (Chris)
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-10-matthew.auld@intel.com
Now that we are using struct resource to track the stolen region, it is
more convenient if we track the reserved portion of that region in a
resource as well.
v2: s/<= end + 1/< end/ (Chris)
v3: prefer DEFINE_RES_MEM
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-7-matthew.auld@intel.com
Now that we are using struct resource to track the stolen region, it is
more convenient if we track dsm in a resource as well.
v2: check range_overflow when writing to 32b registers (Chris)
pepper in some comments (Chris)
v3: refit i915_stolen_to_dma()
v4: kill ggtt->stolen_size
v5: some more polish
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171211151822.20953-6-matthew.auld@intel.com
v2: add more missing platform tags
v3: change tag to cnp rather than using gen9,gen10
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205190118.7088-2-lucas.demarchi@intel.com
It has been many years since the last confirmed sighting (and fix) of an
RC6 related bug (usually a system hang). Remove the parameter to stop
users from setting dangerous values, as they often set it during triage
and end up disabling the entire runtime pm instead (the option is not a
fine scalpel!).
Furthermore, it allows users to set known dangerous values which were
intended for testing and not for production use. For testing, we can
always patch in the required setting without having to expose ourselves
to random abuse.
v2: Fixup NEEDS_WaRsDisableCoarsePowerGating fumble, and document the
lack of ilk support better.
v3: Clear intel_info->rc6p if we don't support rc6 itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171201113030.18360-1-chris@chris-wilson.co.uk
Instead of sleeping for a fixed 1ms (roughly, depending on timer slack),
start with a small sleep and exponentially increase the sleep on each
cycle.
A good example of a beneficiary is the guc mmio communication channel.
Typically we expect (and so spin) for 10us for a quick response, but this
doesn't cover everything and so sometimes we fallback to the millisecond+
sleep. This incurs a significant delay in time-critical operations like
preemption (igt/gem_exec_latency), which can be improved significantly by
using a small sleep after the spin fails.
We've made this suggestion many times, but had little experimental data
to support adding the complexity.
v2: Bump the minimum usleep to 10us on advice of
Documentation/timers/timers-howto.txt (Tvrko)
v3: Specify min, max range for usleep intervals -- some code may
crucially depend upon and so want to specify the sleep pattern.
References: 1758b90e38 ("drm/i915: Use a hybrid scheme for fast register waits")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: John Harrison <John.C.Harrison@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171124130031.20761-2-chris@chris-wilson.co.uk
Since commit 6060b6aec0 ("drm/i915/pmu: Add RC6 residency metrics"),
vlv_residency_raw() may be called from an irq-disabled context (via perf
event sampling on remote cpu). As such, we can no longer assume that we
are called from process context and must save/restore the irq state for
the spinlock.
Fixes: 6060b6aec0 ("drm/i915/pmu: Add RC6 residency metrics")
Testcase: igt/perf_pmu/other-init-3
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171122222510.22627-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Replace the 0 and 1 with PLANE_A and PLANE_B in the pre-g4x wm code.
v2: s/old_plane_id/i9xx_plane_id/ (Daniel)
v3: s/plane/i9xx_plane/ etc. (James)
Cc: James Ausmus <james.ausmus@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-5-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
GEN6_RC_VIDEO_FREQ is deprecated for >= gen10;
don't try to program it.
v2: Use IS_GEN9() instead of INTEL_GEN() and remove comment (Rodrigo)
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117080146.20150-1-david.weinehall@linux.intel.com
This reverts commit 8f067837c4.
HSD says "WA withdrawn. It was causing corruption with some images.
WA is not strictly necessary since this bug just causes loss of FBC
compression with some sizes and images, but doesn't break anything."
Fixes: 8f067837c4 ("drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117010825.23118-1-radhakrishna.sripada@intel.com
The watermarks it should calculate against are the old optimal watermarks.
The currently active crtc watermarks are pure fiction, and are invalid in
case of a nonblocking modeset, page flip enabling/disabling planes or any
other reason.
When the crtc is disabled or during a modeset the intermediate watermarks
don't need to be programmed separately, and could be directly assigned
to the optimal watermarks.
CXSR must always be disabled in the intermediate case for modesets,
else we get a WARN for vblank wait timeout.
Also rename crtc_state to new_crtc_state, to distinguish it from the old
state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115163157.14372-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The watermarks it should calculate against are the old optimal watermarks.
The currently active crtc watermarks are pure fiction, and are invalid in
case of a nonblocking modeset, page flip enabling/disabling planes or any
other reason.
When the crtc is disabled or during a modeset the intermediate watermarks
don't need to be programmed separately, and could be directly assigned
to the optimal watermarks.
CXSR must always be disabled in the intermediate case for modesets, else
we get a WARN for vblank wait timeout.
Also rename crtc_state to new_crtc_state, to distinguish it from the old state.
Changes since v1:
- Use intel_atomic_get_old_crtc_state. (ville)
Changes since v2:
- Always unset cxsr during modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115163157.14372-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
gem_workarounds reports that the SLICE_UNIT_LEVEL_CLKGATE write isn't
sticking. Commit 0a60797a0e ("drm/i915: Implement
ReadHitWriteOnlyDisable.") presumes that SLICE_UNIT_LEVEL_CLKGATE is a
masked register in the context image, but commit 90007bca61
("drm/i915/cnl: Introduce initial Cannonlake Workarounds.") lists it as
an ordering unmasked register. The masked write will be losing the
default settings if we trust the original commit. That gem_workarounds
reports the value is lost entirely is more worrying though -- but it
clearly suggests that it is not a masked register in the context image,
so unify both w/a to use the original rmw.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103705
Fixes: 0a60797a0e ("drm/i915: Implement ReadHitWriteOnlyDisable.")
References: 90007bca61 ("drm/i915/cnl: Introduce initial Cannonlake Workarounds.")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Rafael Antognolli <rafael.antognolli@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171111100336.11020-1-chris@chris-wilson.co.uk
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
GEN8_CONFIG0 (0xD00) is a protected by a lock (bit 31) which is set by
the BIOS, so there is no way we can enable the three chicken bits
mandated by the WA (the BIOS should be doing it instead).
v2: Rebased
v3: Standalone patch
References: b033bb6d5d ("drm/i915/gen9: Enable must set chicken bits in config0 reg")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510185589-9100-2-git-send-email-oscar.mateo@intel.com
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that we always execute a context switch upon module load, there is
no need to queue a delayed task for doing so. The purpose of the delayed
task is to enable GT powersaving, for which we need the HW state to be
valid (i.e. having loaded a context and initialised basic state). We
used to defer this operation as historically it was slow (due to slow
register polling, fixed with commit 1758b90e38 ("drm/i915: Use a hybrid
scheme for fast register waits")) but now we have a requirement to save
the default HW state.
v2: Load the kernel context (to provide the power context) upon resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171112112738.1463-3-chris@chris-wilson.co.uk
GT powersaving is tightly coupled to the request infrastructure. To
avoid complications with the order of initialisation in the next patch
(where we want to send requests to hw during GEM init) move the
powersaving initialisation into the purview of i915_gem_init().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110142634.10551-3-chris@chris-wilson.co.uk
Apparently setting up a bunch of GT registers before we've properly
initialized the rest of the GT hardware leads to these setting being
lost. So looks like I broke HSW with commit b7048ea12f ("drm/i915:
Do .init_clock_gating() earlier to avoid it clobbering watermarks")
by doing init_clock_gating() too early. This should actually affect
other platforms as well, but apparently not to such a great degree.
What I was ultimately after in that commit was to move the
ilk_init_lp_watermarks() call earlier. So let's undo the damage and
move init_clock_gating() back to where it was, and call
ilk_init_lp_watermarks() just before the watermark state readout.
This highlights how fragile and messed up our init order really is.
I wonder why we even initialize the display before gem. The opposite
order would make much more sense to me...
v2: Keep WaRsPkgCStateDisplayPMReq:hsw early as it really must
be done before all planes might get disabled.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mark Janes <mark.a.janes@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reported-by: Mark Janes <mark.a.janes@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103549
Fixes: b7048ea12f ("drm/i915: Do .init_clock_gating() earlier to avoid it clobbering watermarks")
References: https://lists.freedesktop.org/archives/intel-gfx/2017-November/145432.html
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171108133555.14091-1-ville.syrjala@linux.intel.com
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Smatch warns of
drivers/gpu/drm/i915/intel_pm.c:1161 g4x_compute_wm() warn: signedness bug returning '(-33554430)'
which is a result of it believing that wm may be INT_MAX following
g4x_tlb_miss_wa(). Just declaring g4x_tlb_miss_wa() as returning an
unsigned integer is not sufficient, we need to tell smatch that wm itself
is unsigned for it to not worry. So mark up the locals we expect to be
non-negative, and so silence smatch.
v2: Mark up vlv_compute_wm_level() as unsigned similarly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20171107140338.13748-1-chris@chris-wilson.co.uk
The watermarks it should calculate against are the old optimal watermarks.
The currently active crtc watermarks are pure fiction, and are invalid in
case of a nonblocking modeset, page flip enabling/disabling planes or any
other reason.
When the crtc is disabled or during a modeset the intermediate watermarks
don't need to be programmed separately, and could be directly assigned
to the optimal watermarks.
Changes since v1:
- Use intel_atomic_get_old_crtc_state. (ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019151341.4579-2-maarten.lankhorst@linux.intel.com
[mlankhorst: Add cc stable and bugzilla link, since previous patch doesn't fix issue by itself]
Cc: stable@vger.kernel.org #v4.8+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102373
The original intent was to preserve watermarks as much as possible
in intel_pipe_wm.raw_wm, and put the validated ones in intel_pipe_wm.wm.
It seems this approach is insufficient and we don't always preserve
the raw watermarks, so just use the atomic iterator we're already using
to get a const pointer to all bound planes on the crtc.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102373
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org #v4.8+
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019151341.4579-1-maarten.lankhorst@linux.intel.com
This is heavily based on a initial patch provided by Ville
plus all changes provided later by Ander.
As Geminilake, Cannonlake also supports 2 pixels per clock.
Different from Geminilake we are not implementing the 99% Wa.
But we can revisit that decision later if we find out
any limitation on later CNL SKUs.
v2: Rebase on top of commit 'd305e0614601 ("drm/i915: Track
minimum acceptable cdclk instead of "minimum dotclock")'
v3: When fixing HDMI on CNL I noticed that I missed to convert
back the doubled pixel rate to cdclk.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003223142.26264-1-rodrigo.vivi@intel.com
On CNL, individual wake rate limit was added to each engine.
GT can only go to RC6 if both Render and Media engines are
individually qualified. So we need to set their individual
wake rate limit.
+-----------------+---------------+--------------+--------------+
| | GT RC6 | Render C6 | Media C6 |
+-----------------+---------------+--------------+--------------+
| Wake rate limit | 0xA09C[31:16] | 0xA09C[15:0] | 0xA0A0[15:0] |
+-----------------+---------------+--------------+--------------+
v2: - Tune Render and Media wake rate values according to some extra
info I got from HW engineers. Value can be tuned, but for now
these are the recommended values.
- Fix typos pointed by James.
Cc: Nathan Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023224612.27208-1-rodrigo.vivi@intel.com
Otherwise we are blasting other bits in GEN8_L3SQCREG1 that might be important
(although we probably aren't at the moment because 0 seems to be the default
for all the other bits).
v2: Extra parentheses (Michel)
Fixes: 050fc46 ("drm/i915:bxt: implement WaProgramL3SqcReg1DefaultForPerf")
Fixes: 450174f ("drm/i915/chv: Tune L3 SQC credits based on actual latencies")
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1508271945-14961-1-git-send-email-oscar.mateo@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Apparently RC6 residency is lower than expected
with EI mode for most of the cases on CNL A0, B0 and C0.
This Wa doesn't solve our lower residency, but I
believe it is better to have it since EI is not
expected to work by HW engineers anyways.
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822235828.18322-1-rodrigo.vivi@intel.com
Defined new struct intel_rc6 to hold RC6 specific state and
intel_ring_pstate to hold ring specific state.
v2: s/intel_ring_pstate/intel_llc_pstate. Removed checks from
autoenable_* functions. (Chris)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-13-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-12-chris@chris-wilson.co.uk
Prepared generic functions intel_enable_rc6, intel_disable_rc6,
intel_enable_rps and intel_disable_rps functions to setup RC6/RPS
based on platforms.
v2: Make intel_enable/disable_rc6/rps static. (Chris)
v3: Added lockdep_assert_held(dev_priv->pcu_lock) in new generic
functions. (Chris)
Removed WARN_ON(&dev_priv->pcu_lock) from lower level functions as generic
function now has lockdep_assert. Rebase.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-12-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-11-chris@chris-wilson.co.uk
Prepared intel_update_ring_freq function to setup ring frequency
for applicable platforms determined by macro HAS_LLC.
v2: Replaced NEEDS_RING_FREQ_UPDATE with HAS_LLC macro. (Chris)
Added check while calling from intel_enable_gt_powersave.
v3: s/intel_update_ring_freq/intel_enable_llc_pstate and created
new placeholder function intel_disable_llc_pstate. (Chris)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-11-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-10-chris@chris-wilson.co.uk
This function gives the status of RC6, whether disabled or if
enabled then which state. intel_enable_rc6 will be used for
enabling RC6 in the next patch.
v2: Rebase.
v3: Rebase.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1
Reviewed-by: Ewelina Musial <ewelina.musial@intel.com> #1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-10-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-9-chris@chris-wilson.co.uk
Prepared substructure rps for RPS related state. autoenable_work is
used for RC6 too hence it is defined outside rps structure. As we do
this lot many functions are refactored to use intel_rps *rps to access
rps related members. Hence renamed intel_rps_client pointer variables
to rps_client in various functions.
v2: Rebase.
v3: s/pm/gt_pm (Chris)
Refactored access to rps structure by declaring struct intel_rps * in
many functions.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-9-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-8-chris@chris-wilson.co.uk
In order to separate GT PM related functionality into new structure
we are updating rps structure. hw_lock in it is used for display
related PCU communication too hence move it to dev_priv.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-8-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-7-chris@chris-wilson.co.uk
This patch separates enable/disable of RC6 and RPS for VLV.
v2: Removed unnecessary comments about forcewakes while enabling
RC6/RPS. Added changes to output turbo control status for VLV in
i915_frequency_info.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-5-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-4-chris@chris-wilson.co.uk
This patch separates RC6 and RPS enabling for BDW.
RC6/RPS Disabling are handled through gen6 functions.
PM Programming guide recommends a sequence within forcewakes to
configure RC6, RPS and ring frequencies in sequence. With this
patch the order is still maintained.
v2: Update sequence numbers in RC6 programming and comment about
intent of reset_rps during gen8_enable_rps. (Radoslaw)
v3: Rebase.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-4-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-3-chris@chris-wilson.co.uk
This patch removes all IS_BROADWELL checks and non-BDW changes from
gen8_enable_rps as it is called only for BROADWELL.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-3-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-2-chris@chris-wilson.co.uk
Remove dependency for I915_MAX_PIPES by replacing it with
for_each_pipe() macro.
v2: use 'enum pipe pipe' instead of 'i'
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630626-23806-3-git-send-email-mika.kahola@intel.com
When SW enables the use of 2M/1G pages, it must disable the GTT cache.
v2: don't disable for Cherryview which doesn't even support 48b PPGTT!
v3: explicitly check that the system does support 2M/1G pages
v4: split WA and decision logic
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171006145041.21673-12-matthew.auld@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171006221833.32439-11-chris@chris-wilson.co.uk
According to Spec for SKL+: "Isochronous Priority Control.
If enabled, Display sends demoted requests once the transition
watermark is reached. If transition watermark is not enabled,
Display sends demoted requests when the display buffer is full."
The commit 'e57f1c02155f ("drm/i915/gen9+: Add has_ipc flag in
device info structure")' introduced that as gen9+ but missing many
SKL Skus.
I believe the reason for that is Spec also mentions workarounds for
SKL-ALL: "IPC (Isoch Priority Control) may cause underflows
WA: Do not enable IPC in register ARB_CTL2"
It seems lame to add the feature and forever disable it,
but it will avoid a mistake of enabling it when we are reorganizing
the feature definitions on i915_pci.c later.
It will also allow us to probably extend that workaround for
other platforms.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003063652.17248-1-rodrigo.vivi@intel.com
Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.
v5: pure rename
v6: fix
Credits-to: Coccinelle
@@
identifier n;
@@
(
- i915.n
+ i915_modparams.n
)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com
Don't touch other bits. My bad.
I haven't seen any case where those other bits appeard to be
set before we touch it, but it is safe to avoid touching
other bits we weren't told to touch.
Fixes: 0a46ddd57c ("drm/i915/cnp: Wa 1181: Fix Backlight issue")
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908234534.17986-1-rodrigo.vivi@intel.com
Use the LLC/eLLC hotspot avoidance mode for CCS on LLC machines. This is
reported to give better performance.
Testing has indicated that we don't need to enforce any massive 2 or 4
MiB alignment for all compressed resources even though there are still
plenty of stale comments in the spec suggesting that we do.
We do need to make sure every hardware unit that deals with the
compressed data uses the same hash mode.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170824191100.10949-4-ville.syrjala@linux.intel.com
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
This patch adds IPC support. This patch also enables IPC in all supported
platforms based on has_ipc flag.
IPC (Isochronous Priority Control) is the hardware feature, which
dynamically controls the memory read priority of Display.
When IPC is enabled, plane read requests are sent at high priority until
filling above the transition watermark, then the requests are sent at
lower priority until dropping below the level 0 watermark.
The lower priority requests allow other memory clients to have better
memory access. When IPC is disabled, all plane read requests are sent at
high priority.
Changes since V1:
- Remove commandline parameter to disable ipc
- Address Paulo's comments
Changes since V2:
- Address review comments
- Set ipc_enabled flag
Changes since V3:
- move ipc_enabled flag assignment inside intel_ipc_enable function
Changes since V4:
- Re-enable IPC after suspend/resume
Changes since V5:
- Enable IPC for all gen >=9 except SKL
Changes since V6:
- fix commit msg
- after resume program IPC based on SW state.
Changes since V7:
- Modify IPC support check based on HAS_IPC macro (suggested by Chris)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-8-mahesh1.kumar@intel.com
CNL:A & CNL:B have same workaround as KBL to increase wm level latency
by 4us if IPC is enabled.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-6-mahesh1.kumar@intel.com
IF IPC is enabled LINETIME_WM value should be half of calculated value
line time = ROUNDDOWN(1/2 * Calculated Line Time)
Earlier code was rounding-up the value, But updated Bspec says we should
take the ROUNDDOWN. This patch corrects that as well.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-5-mahesh1.kumar@intel.com
GEN > 9 require transition WM to be programmed if IPC is enabled.
This patch calculates & enable transition WM for supported platforms.
If transition WM is enabled, Plane read requests are sent at high
priority until filling above the transition watermark, then the
requests are sent at lower priority until dropping below the level-0 WM.
The lower priority requests allow other memory clients to have better
memory access.
transition minimum is the minimum amount needed for trans_wm to work to
ensure the demote does not happen before enough data has been read to
meet the level 0 watermark requirements.
transition amount is configurable value. Higher values will
tend to cause longer periods of high priority reads followed by longer
periods of lower priority reads. Tuning to lower values will tend to
cause shorter periods of high and lower priority reads.
Keeping transition amount to 10 in this patch, as suggested by HW team.
Changes since V1:
- Address review comments from Maarten
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-4-mahesh1.kumar@intel.com
Plane configuration parameters doesn't change for each WM-level
calculation. Currently we compute same parameters 8 times for each
wm-level.
This patch optimizes it by calculating these parameters in beginning
& reuse during each level-wm calculation.
Changes since V1:
- rebase on top of Rodrigo's series for CNL
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-3-mahesh1.kumar@intel.com
Skip compressing 1 segment at the end of the frame,
avoid a pixel count mismatch nuke event when last active
pixel and dummy pixel has same color for Odd Plane
Width / Height.
For both platforms Gemini Lake and Cannon Lake.
v2: Use function-like macro and also use mask to clean
to make sure bit 11 is 0. (Suggested by Paulo).
v3: Add Display WA notation and also apply for GLK.
Both Forgotten on v2.
Using "GLK_" prefix since GLK came before CNL.
v4: Forgot to "|=" when moving directly macro to masked
val. (Noticed by Paulo.)
v5: Rebased on top of 0a46ddd57c ("drm/i915/cnp: Wa 1181:
Fix Backlight issue")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905193013.31710-1-rodrigo.vivi@intel.com
This workaround fixes a CNL PCH bug when changing
backlight from a lower frequency to a higher frequency.
During random reboot cycles, display backlight seems to
be off/ dim for 2-3 mins.
The only functional change on this patch is to
set bit 13 of 0xC2020 for CNL PCH.
The rest of patch is organizing identation around
those bits definitions and re-organizing CFL workarounds.
v2: Only add the bit that matters without touching others
around (Jani).
Rebase on top of clock gating functions rename.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831045223.3960-1-rodrigo.vivi@intel.com
Chris Wilson