This variable is redundant since we can use
common->bt_ant_diversity to determine if diversity
has to be enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MC_GAIN_CTL/CCK_DETECT registers have to be programmed
with the correct configuration values if WLAN/BT RX diversity
is enabled. Add this and also take care of the BTCOEX mode
when fast diversity is enabled/disabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom solution for Asus is WB195 based and supports
WLAN/BT Rx diversity. Identify this card and set the
capability.
CUS198/CUS230, which are based on WB225 also support
WLAN/BT Rx diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "ath9k_hw_set_bt_ant_diversity" instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of this capability to restrict the usage of the
debugfs file and modparam using which this feature can
be enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For single-chain WLAN+BT cards, the BT antenna can be used for
WLAN RX when the BT interface is disabled. Rename the modparam
"antenna_diversity" to "bt_ant_diversity" to clarify this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198/CUS230 need a few tweaks in the antenna diversity
algorithm to accomodate RSSI variation. Add a couple
of knobs to control low RSSI threshold and fast antenna
diversity bias values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a function to do a ratio comparison for ALT,
so make use of it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now, it is being done for all cases.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
4965 version of Eric patch "iwl3945: better skb management in rx path".
It fixes several problems :
1) skb->truesize is underestimated.
We really consume PAGE_SIZE bytes for a fragment,
not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With recent patches ssb can fetch info about serial flash and register
it as a platform device. No more reasons to mark it BROKEN.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move rtl92cu_update_hal_rate_tbl declaration to hw.h to correspond with function
definition in hw.c.
Fixes sparse warning in hw.c warning: symbol 'rtl92cu_update_hal_rate_tbl' was
not declared.
Signed-off-by: Mark Schulte <schultetwin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever available, use cfg80211_scan_request to populates rates
in outgoing probe request. This will help to advertise band specific
rates and fix an issue where 11b rates were advertised in probe
request going out on 11a band.
This will also ensure that we do not advertise 11b rates while P2P
scan is going on.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has introduced by recent commit 6b41f941d7cd: "mwifiex:
handle driver initialization error paths" which adds error
path handling for mwifiex_fw_dpc().
release_firmware(adapter->*) is called for success as well
as failure paths. In failure paths, adapter is already freed
at this point.
The issue is fixed by moving mwifiex_free_adapter() call.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is fully supported by iwlwmvm, so advertise
it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the NIC is expected to operate in high temperature,
it is advisable to put more aggresive thermal throttling
parameters, in order to prevent CT-kill.
Signed-off-by: eytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wey-Yi has moved on a while ago, but we forgot to update the
maintainers file. Since Emmanuel is de facto maintaining the
driver along with myself now, list him instead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set beacon abort escape timer values - 6 beacons in D0 state,
9 beacons in D3 and D0i3.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate scale windows are cleared twice as part of the init.
Cleanup this duplication in both mvm and dvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This API isn't valid any more. It wasn't used anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of reporting the maximum signal strength and the
antenna bitmap in the antenna field (which is really just
for radiotap and defined differently), report the signal
strength values per chain and set the chain bitmap.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If fw_restart is disabled, using the fw_restart debugfs
file will enable fw_restart and then send the failing
command, but this still frequently fails restart because
it resets fw_restart afterwards and is thus racy.
Fix this by tracking fw_restart separately and allowing
"always restart", "never restart" and "restart N times".
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change beacon filtering command due to a change in the API.
In case the FW supports the old API, we do not send the
BF HCMD and assume that since the corresponding struct in
the FW is zeroed by default then we don't need to disable
it in the FW actively.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current registered the per-vif debugfs handler for
STA mode only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
To make maintaining some constant default values in the
driver easier, declare them in a separate file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assigning quota per used binding (channel) assign
the same amount of quota for each virtual interface so that
when there are more than two interfaces using more than one
channel, we'll stay on the channels proportionally to the
number of virtual interfaces using the channels.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return in case that HW restart is in progress but the added
interface is not found during the iteration over all the interfaces.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently after sending EAPOL frame FW transition to power saving mode
within 10 or 100 msec (as specified by power table command). According
to new requirement this timeout for a specific EAPOL frame must be
controlled by the driver by setting tx_pm_timeout field of TX_CMD to 2
(PM_FRAME_ENUM_MGMT). This value corresponds to 32 msec timeout.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware supports offloading more IPv6 addresses for NDP,
adjust the code to send the correct command depending on the
firmware capability.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support Tx power limitations. These limitations can come from
mac80211 for various reasons.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we get a firmware error during restart, we currently abandon any
hope and simply fail, getting stuck until the driver is reloaded.
Unfortunately, there isn't really much else we can do since restart
will likely continue to fail, and asking mac80211 for disconnection
just causes more error.
To allow the user to at least set up the device again completely
from scratch, reprobe the device and in doing so completely destroy
any mac80211/driver state.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fw is now able to run TX_IQ_SKEW and RX_IQ_SKEW by
itself. No need for default values any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A new API that replaces the rx signal strength calculation via agc & rssi.
The energy is now calculated outside the driver and transferred by the fw.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If RTS and fragmentation threshold values are
0xFFFFFFFF they should be considered disabled and
no min/max limits must be applied.
This fixes some issues with throughput issues,
especially with VHT.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases channel arrays were never freed.
The patch also unifies error handling in the mac
setup function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Endpoints are re-initialized upon HTC start anyway
so there's no need to do that twice in case of
restarting HTC (i.e. in case of hardware
recovery).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to submit new HTC commands
after/while HTC stopped. This led to memory
corruption in some rare cases.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for testing. To perform a
forced firmware crash write 'crash' to
'simulate_fw_crash' debugfs file. E.g.
echo crash > /sys/kernel/debug/ieee80211/phy1/ath10k/simulate_fw_crash
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sujith Manoharan