Pad retention should be controlled from pin control driver, so remove it
from Exynos LPASS driver. After this change, no more access to PMU regmap
is needed, so remove also the code for handling PMU regmap.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All macros prefixed with AT91[SAM9]_SMC have been replaced by equivalent
definitions prefixed with ATMEL_SMC, and the at91sam9_smc_xxxx() helpers
are no longer used.
Drop these definitions before someone starts using them again.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These new helpers + macro definitions are meant to replace the old ones
which are unpractical to use.
Note that the macros and function prefixes have been intentionally
changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that
this IP is also embedded in avr32 SoCs (and not only in at91 ones).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For better understanding of relationship between headers and modules
rename:
intel_bxtwc.h -> intel_soc_pmic_bxtwc.h
While here, remove file name from the file itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to include intel_soc_pmic.h into header which doesn't
require it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The registers 0x56 and 0x57 of AXP22X PMIC store the value of the
internal temperature of the PMIC.
This patch modifies the name of these registers from AXP22X_PMIC_ADC_H/L
to AXP22X_PMIC_TEMP_H/L so their purpose is clearer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TI LMU (Lighting Management Unit) driver supports lighting devices below.
LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
LMU devices have common features.
- I2C interface for accessing device registers
- Hardware enable pin control
- Backlight brightness control
- Notifier for hardware fault monitoring
- Regulators for LCD display bias
It contains fault monitor, backlight, LED and regulator driver.
LMU fault monitor
-----------------
LM3633 and LM3697 provide hardware monitoring feature.
It enables open or short circuit detection.
After monitoring is done, each device should be re-initialized.
Notifier is used for this case.
Separate patch for 'ti-lmu-fault-monitor' will be sent later.
Backlight
---------
It's handled by TI LMU backlight consolidated driver and
chip dependent data. Separate patchset will be sent later.
LED indicator
-------------
LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
supported. Separate patch for 'leds-lm3633' will be sent later.
Regulator
---------
LM3631 has 5 regulators for the display bias.
LM3632 supports 3 regulators. One consolidated driver enables it.
The lm363x regulator driver is already upstreamed.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation for sharing this driver with Madera, move the pdata
for the LDO1 regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_ldo1_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for sharing this driver with Madera, move the pdata
for the micsupp regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_micsupp_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
-----BEGIN PGP SIGNATURE-----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=zHqs
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fourth set of IIO new device support, features and cleanups for the 4.12 cycle
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
One of the features of STM32 trigger hardware block is a quadrature
encoder that can counts up/down depending of the levels and edges
of the selected external pins.
This patch allow to read/write the counter, get it direction,
set/get quadrature modes and get scale factor.
When counting up preset value is the limit of the counter.
When counting down the counter start from preset value down to 0.
This preset value could be set/get by using
/sys/bus/iio/devices/iio:deviceX/in_count0_preset attribute.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CPCAP can sense if IRQ is currently set or not. This
functionality is required for a few subdevices, such
as the power button and usb phy modules.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Phy drivers access PMU region through regmap provided by exynos-pmu
driver. However there is no need to duplicate defines for PMU
registers. Instead just use whatever is defined in exynos-regs-pmu.h.
This reduces number of defines.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Phy drivers access PMU region through regmap provided by exynos-pmu
driver. However there is no need to duplicate defines for PMU
registers. Instead just use whatever is defined in exynos-regs-pmu.h.
Additionally MIPI PHY registers for Exynos5433 start from the same
address as Exynos4 and Exynos5250 so re-use existing defines.
This reduces number of defines and allows removal of one header file.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For SPI, we can get up to 32 additional bytes for response preamble.
The current overhead (2 bytes) may cause problems when we try to receive
a big response. Update it to 32 bytes.
Without this fix we could see a kernel BUG when we receive a big response
from the Chrome EC when is connected via SPI.
Signed-off-by: Vic Yang <victoryang@google.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo.collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add various bits of code needed to support i.MX7D variant of the IP.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Cc: yurovsky@gmail.com
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Dong Aisheng <dongas86@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY4ZYkAAoJEHm+PkMAQRiGsq4H/R4PMXDoe2XhSSk7IoT97pXV
/A8np/scAPjzEgYUidbb54OSqWwsPRuPGWONTFeSrE2u0L4wln/REI91jg7QetLq
IisncExlYeJ/XQ+iO0ZZh9fLbqwIlEJFdSXmyIFr3m/TBxe8a61C8j93oNgM1tHT
yuwzlq7c3sLq2hsmUG2HyL2kJsEfRasv4Rk0yhFuti12zVsBoTW4qmZuMauq+gdf
f7cSYgiHhPTdb2o+azg5O7uYNHaQQBxdUMlIuhhYtVOUq+pFDO23SLHSFIW2NwOm
Zn5R6CFSrLsCw0Bx0v8Xlc151QUbaRK4h9lhUhkBr6d3uNShU1NQ9JojpSvYwBo=
=vP6E
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rc5' into next
Sync up with mainline to bring in changes to input subsystem merged
through other trees.
Some form factors (detachables/tablets) may not have a keyboard and
thus user may have to resort to using a defined EC UI to send sysrq(s)
to the kernel in order to collect crash info etc. This UI typically
is in the form of user pressing volume / power buttons in some specific
sequence and for some specific time. Add a new EC event that allows EC
to communicate the sysrq to the AP.
(We're skipping event number 5 because it has been reserved for
something else)
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes compilation for files, that try to include the
cpcap header in alphabetically sorted #include lists.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the basic ability to register the device through device tree, more
work is needed to get each individual sub-driver functioning correctly
but this is enough to get the device to probe from device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.
This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.
This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add new !TOUCHSCREEN_SUN4I dependency for SUN4I_GPADC
- List include/dt-bindings/mfd/* to files supported in MAINTAINERS
- New Drivers
- Intel Apollo Lake SPI NOR
- ST STM32 Timers (Advanced, Basic and PWM)
- Motorola 6556002 CPCAP (PMIC)
- New Device Support
- Add support for AXP221 to axp20x
- Add support for Intel Gemini Lake to intel-lpss-pci
- Add support for MT6323 LED to mt6397-core
- Add support for COMe-bBD#, COMe-bSL6, COMe-bKL6,
COMe-cAL6 and COMe-cKL6 to kempld-core
- New Functionality
- Add support for Analog CODAC to sun6i-prcm
- Add support for Watchdog to lpc_ich
- Fix-ups
- Error handling improvements; axp288_charger, axp20x, ab8500-sysctrl
- Adapt platform data handling; axp20x
- IRQ handling improvements; arizona, axp20x
- Remove superfluous code; arizona, axp20x, lpc_ich
- Trivial coding style/spelling fixes; axp20x, abx500, mfd.txt
- Regmap fix-ups; axp20x
- DT changes; mfd.txt, aspeed-lpc, aspeed-gfx, ab8500-core, tps65912, mt6397
- Use new I2C probing mechanism; max77686
- Constification; rk808
- Bug Fixes
- Stop data transfer whilst suspended; cros_ec
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYrYwQAAoJEFGvii+H/HdhVMMP/3Y5/S1y7bCRhsta3PQVHT/2
+nxu833451qTTUKNqR5rTQrjdjVLr6+rfhMmMxIDhHMrn3EvwT0bQDQmncLLYgc2
u5n2j93Y/nfyJvy76W3aTlisBaKfxhFBuLBEkewXNwPaZk97tbgf9IbyNq6eirHo
afv5Z54q9RN+OlT5ZfM8mJcOQAdyE6CXzq/GKZI6LjSqPb5vQhasqoD/yb9pMMga
jYseI47KlIVLhUnnAjxRdxt16rjtee2JHZmGCGJaeo+nWiTwDOZ5l5eZDHKwD6ng
3CW4xWDPbzeLD22oi6Uzvhx+8Eqt9S/K1AY+kn3W6WLk/CTi5yamMHw0DjBUcS9a
hqdqGZrCSveRQrSCt/9N5uzSMkiUHFMGdj5LtX3yB4fDp0R42WJGMxkvidKb7otB
wJIT0i5T5M5G3IT3xPkdEtfEAK3xoAus+IF0faFNaD7GqsEs97KD+740nTgulSKz
g28Lo6NLpZhl+uQ74fx76Wll+Onj1voWABZW8Z//kjRWkAwKU8OhbXrX8kccGY6m
C980wWtj0979jYFstwUuSXspjuvk9L1nfSuLBmtawm9S58TUIS/WLe2A8kU9/XEY
e3PLpO4AxvCJvBBa80yVFG15JoaTX5TOg/F3NqKYaHqA2cusOVOEFAeOAdwav2rL
SR2Y8s8ceIL4n9ccmr0b
=P5Dp
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add new !TOUCHSCREEN_SUN4I dependency for SUN4I_GPADC
- List include/dt-bindings/mfd/* to files supported in MAINTAINERS
New Drivers:
- Intel Apollo Lake SPI NOR
- ST STM32 Timers (Advanced, Basic and PWM)
- Motorola 6556002 CPCAP (PMIC)
New Device Support:
- Add support for AXP221 to axp20x
- Add support for Intel Gemini Lake to intel-lpss-pci
- Add support for MT6323 LED to mt6397-core
- Add support for COMe-bBD#, COMe-bSL6, COMe-bKL6, COMe-cAL6 and
COMe-cKL6 to kempld-core
New Functionality:
- Add support for Analog CODAC to sun6i-prcm
- Add support for Watchdog to lpc_ich
Fix-ups:
- Error handling improvements; axp288_charger, axp20x, ab8500-sysctrl
- Adapt platform data handling; axp20x
- IRQ handling improvements; arizona, axp20x
- Remove superfluous code; arizona, axp20x, lpc_ich
- Trivial coding style/spelling fixes; axp20x, abx500, mfd.txt
- Regmap fix-ups; axp20x
- DT changes; mfd.txt, aspeed-lpc, aspeed-gfx, ab8500-core, tps65912,
mt6397
- Use new I2C probing mechanism; max77686
- Constification; rk808
Bug Fixes:
- Stop data transfer whilst suspended; cros_ec"
* tag 'mfd-for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (43 commits)
mfd: lpc_ich: Enable watchdog on Intel Apollo Lake PCH
mfd: lpc_ich: Remove useless comments in core part
mfd: Add support for several boards to Kontron PLD driver
mfd: constify regmap_irq_chip structures
MAINTAINERS: Add include/dt-bindings/mfd to MFD entry
mfd: cpcap: Add minimal support
mfd: mt6397: Add MT6323 LED support into MT6397 driver
Documentation: devicetree: Add LED subnode binding for MT6323 PMIC
mfd: tps65912: Export OF device ID table as module aliases
mfd: ab8500-core: Rename clock device and compatible
mfd: cros_ec: Send correct suspend/resume event to EC
mfd: max77686: Remove I2C device ID table
mfd: max77686: Use the struct i2c_driver .probe_new instead of .probe
mfd: max77686: Use of_device_get_match_data() helper
mfd: max77686: Don't attempt to get i2c_device_id .data
mfd: ab8500-sysctrl: Handle probe deferral
mfd: intel-lpss: Add Intel Gemini Lake PCI IDs
mfd: axp20x: Fix AXP806 access errors on cold boot
mfd: cros_ec: Send suspend state notification to EC
mfd: cros_ec: Prevent data transfer while device is suspended
...
Here is the big staging and iio driver patchsets for 4.11-rc1.
We almost broke even this time around, with only a few thousand lines
added overall, as we removed the old and obsolete i4l code, but added
some new drivers for the RPi platform, as well as adding some new IIO
drivers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2j/w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymZ1ACdFR4o6xYrWEizmao4a/u+lUZE1aIAnRmcGcIc
J+leO1n9bE5iadQvKYUW
=sKVA
-----END PGP SIGNATURE-----
Merge tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio driver updates from Greg KH:
"Here is the big staging and iio driver patchsets for 4.11-rc1.
We almost broke even this time around, with only a few thousand lines
added overall, as we removed the old and obsolete i4l code, but added
some new drivers for the RPi platform, as well as adding some new IIO
drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (669 commits)
Staging: vc04_services: Fix the "space prohibited" code style errors
Staging: vc04_services: Fix the "wrong indent" code style errors
staging: octeon: Use net_device_stats from struct net_device
Staging: rtl8192u: ieee80211: ieee80211.h - style fix
Staging: rtl8192u: ieee80211: ieee80211_tx.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_BAProc.c - style fix
Staging: rtl8192u: ieee80211: ieee80211_module.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_TSProc.c - style fix
Staging: rtl8192u: r8192U.h - style fix
Staging: rtl8192u: r8192U_core.c - style fix
Staging: rtl8192u: r819xU_cmdpkt.c - style fix
staging: rtl8192u: blank lines aren't necessary before a close brace '}'
staging: rtl8192u: Adding space after enum and struct definition
staging: rtl8192u: Adding space after struct definition
Staging: ks7010: Add required and preferred spaces around operators
Staging: ks7010: ks*: Remove redundant blank lines
Staging: ks7010: ks*: Add missing blank lines after declarations
staging: visorbus, replace init_timer with setup_timer
staging: vt6656: rxtx.c Removed multiple dereferencing
staging: vt6656: Alignment match open parenthesis
...
- Add support for Marvell SD8787 Wifi/BT chip
- Improve UHS support for SDIO
- Invent MMC_CAP_3_3V_DDR and a DT binding for eMMC DDR 3.3V mode
- Detect Auto BKOPS enable bit
- Export eMMC device lifetime information through sysfs
- First take to slim down the public mmc headers to avoid abuse
- Re-factoring of the mmc block device driver to prepare for blkmq
- Cleanup code for the mmc block device driver
- Clarify and cleanup code dealing with data requests
- Cleanup some code by converting to ida_simple_ functions
- Cleanup code dealing with card quirks
- Cleanup private and public mmc header files
MMC host:
- Don't rely on public mmc headers to include non-mmc related headers
- meson: Add support for eMMC HS400 mode
- meson: Various cleanups and improvements
- omap_hsmmc: Use the proper provided busy timeout from the core
- sunxi: Enable new timings for the A64 MMC controllers
- sunxi: Improvements for clock management
- tmio: Improvements for SDIO interrupts
- mxs-mmc: Add CMD23 support
- sdhci-msm: Enable HS400 enhanced strobe mode support
- sdhci-msm: Correct HS400 tuning sequence
- sdhci-acpi: Support deferred probe
- sdhci-pci: Add support for eMMC HS200 tuning mode on AMD
- mediatek: Correct the implementation of card busy detection
- dw_mmc: Initial support for ZX mmc controller
- sh_mobile_sdhi: Enable support for eMMC HS200 mode
- sh_mmcif: Various cleanups and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iv7W
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for Marvell SD8787 Wifi/BT chip
- Improve UHS support for SDIO
- Invent MMC_CAP_3_3V_DDR and a DT binding for eMMC DDR 3.3V mode
- Detect Auto BKOPS enable bit
- Export eMMC device lifetime information through sysfs
- First take to slim down the public mmc headers to avoid abuse
- Re-factoring of the mmc block device driver to prepare for blkmq
- Cleanup code for the mmc block device driver
- Clarify and cleanup code dealing with data requests
- Cleanup some code by converting to ida_simple_ functions
- Cleanup code dealing with card quirks
- Cleanup private and public mmc header files
MMC host:
- Don't rely on public mmc headers to include non-mmc related headers
- meson: Add support for eMMC HS400 mode
- meson: Various cleanups and improvements
- omap_hsmmc: Use the proper provided busy timeout from the core
- sunxi: Enable new timings for the A64 MMC controllers
- sunxi: Improvements for clock management
- tmio: Improvements for SDIO interrupts
- mxs-mmc: Add CMD23 support
- sdhci-msm: Enable HS400 enhanced strobe mode support
- sdhci-msm: Correct HS400 tuning sequence
- sdhci-acpi: Support deferred probe
- sdhci-pci: Add support for eMMC HS200 tuning mode on AMD
- mediatek: Correct the implementation of card busy detection
- dw_mmc: Initial support for ZX mmc controller
- sh_mobile_sdhi: Enable support for eMMC HS200 mode
- sh_mmcif: Various cleanups and improvements"
* tag 'mmc-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (145 commits)
mmc: core: add mmc prefix for blk_fixups
mmc: core: move all quirks together into quirks.h
mmc: core: improve the quirks for sdio devices
mmc: core: move some sdio IDs out of quirks file
mmc: core: change quirks.c to be a header file
mmc: sdhci-cadence: fix bit shift of read data from PHY port
mmc: Adding AUTO_BKOPS_EN bit set for Auto BKOPS support
mmc: MAN_BKOPS_EN inverse debug message logic
mmc: meson-gx: add support for HS400 mode
mmc: meson-gx: remove unneeded checks in remove
mmc: meson-gx: reduce bounce buffer size
mmc: meson-gx: set max block count and request size
mmc: meson-gx: improve interrupt handling
mmc: meson-gx: improve meson_mmc_irq_thread
mmc: meson-gx: improve meson_mmc_clk_set
mmc: meson-gx: minor improvements in meson_mmc_set_ios
mmc: meson: Assign the minimum clk rate as close to 400KHz as possible
mmc: core: start to break apart mmc_start_areq()
mmc: block: respect bool returned from blk_end_request()
mmc: block: return errorcode from mmc_sd_num_wr_blocks()
...
QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. We can support it's core features quite easily with regmap_spi
and regmap_irq.
The children of cpcap, such as regulators, ADC and USB, can be just regular
device drivers and defined in the dts file. They get probed as we call
of_platform_populate() at the end of our probe, and then the children
can just call dev_get_regmap(dev.parent, NULL) to get the regmap.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Notify EC when going to or returning from suspend so that proper actions
related to wake events can be taken.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec driver is still active while the device is suspended.
Besides that, it also tries to transfer data even after the I2C host had
been suspended. This patch uses a simple flag to prevent this.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Trivial fix to spelling mistake in MFD headers.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add defines for the AXP288_POWER_REASON and AXP288_RT_BATT_V_H and
AXP288_RT_BATT_V_L and AXP288_BC_* registers. While at it also move the
AXP288_TS_ADC_H-AXP288_GP_ADC_L defines, which for some reason where
in a different place, together with the rest of the AXP288 specific
defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The adc-enable register for the axp288 is 0x82, not 0x84.
0x82 is already defined as AXP20X_ADC_EN1 and that is what the
axp288_adc driver is actually using, so simply drop the wrong
AXP288_PMIC_ADC_EN define.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The interrupt line of the entire family of axp2xx pmics is active-low,
for devicetree enumerated irqs, this is dealt with in the devicetree.
ACPI irq resources have a flag field for this too, I tried using this
on my CUBE iwork8 Air tablet, but it does not contain the right data.
The dstd shows the irq listed as either ActiveLow or ActiveHigh,
depending on the OSID variable, which seems to be set by the
"OS IMAGE ID" in the BIOS/EFI setup screen.
Since the acpi-resource info is no good, simply pass in IRQF_TRIGGER_LOW
on the axp288.
Together with the other axp288 fixes in this series, this fixes the axp288
irq contineously triggering.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation of axp20x_device_remove() have a typo and use
axp20x_device_probe() as name. This patch fix this typo.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the defines for the new buttons and switches connected to the CrosEC.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tG0h
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-iio-pwm-4.11' into test
Immutable branch between MFD, IIO and PWM due for the v4.11 merge window
Pulled into IIO to allow follow up series of triggered capture for the
STM32 ADCs.
This hardware block could at used at same time for PWM generation
and IIO timers.
PWM and IIO timer configuration are mixed in the same registers
so we need a multi fonction driver to be able to share those registers.
version 7:
- rebase on v4.10-rc2
version 6:
- rename files to stm32-timers
- rename functions to stm32_timers_xxx
version 5:
- fix Lee comments about detect function
- add missing dependency on REGMAP_MMIO
version 4:
- add a function to detect Auto Reload Register (ARR) size
- rename the structure shared with other drivers
version 2:
- rename driver "stm32-gptimer" to be align with SoC documentation
- only keep one compatible
- use of_platform_populate() instead of devm_mfd_add_devices()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Casting of_device_get_match_data return value to int causes warning on 64bit
architectures.
../drivers/power/supply/axp20x_usb_power.c: In function
'axp20x_usb_power_probe':
../drivers/power/supply/axp20x_usb_power.c:297:21: warning: cast from
pointer to integer of different size [-Wpointer-to-int-cast]
Fixes: 0dcc70ca86 ("power: supply: axp20x_usb_power: use of_device_id
data field instead of device_is_compatible")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Texas Instrument's TPS65910 has support for compensating RTC crystal
inaccuracies. When enabled every hour RTC counter value will be compensated
with two's complement value.
Signed-off-by: Vesa Jääskeläinen <vesa.jaaskelainen@vaisala.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When the axp288_faul_gauge driver was originally merged, it was
merged with a dependency on some other driver providing platform
data for it.
However the battery-data-framework which should provide that data
never got merged, resulting in x86 tablets / laptops with an axp288
having no working battery monitor, as before this commit the driver
would simply return -ENODEV if there is no platform data.
This commit removes the dependency on the platform_data instead
checking that the firmware has initialized the fuel-gauge and
reading the info back from the pmic.
What is missing from the read-back info is the table to map raw adc
values to temperature, so this commit drops the temperature and
temperature limits properties. The min voltage, charge design and
model name info is also missing. Note that none of these are really
important for userspace to have.
All other functionality is preserved and actually made available
by this commit.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=88471
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When the axp288_charger driver was originally merged, it was merged with
a dependency on some other driver providing platform data for it.
However the battery-data-framework which should provide that data never
got merged, so the axp288_charger as merged upstream has never worked,
its probe method simply always returns -ENODEV.
This commit removes the dependency on the platform_data instead reading
back the charging current and charging voltage that the firmware has set
and using those values as the maximum values the user may set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Many Intel CPUs including Haswell, Broadwell and Baytrail have SPI serial
flash host controller as part of the LPC device. This will populate an MFD
cell suitable for the SPI host controller driver if we know that the LPC
device has one.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move and add registration for the mlx-platform driver. Introduce button and lid
drivers for the surface3 (different from the surface3-pro). Add BXT PMIC TMU
support. Add Y700 to existing ideapad-laptop quirk.
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYVxXxAAoJEKbMaAwKp364mDAIAL750zoO/liY1qfFGktkY2zS
xknJqh4UeIVW6iN9hEq7jQD3jkFl7hNuXgFyogLZgJQge8gfufsOD7ljkhp2wVF2
3Ir437f4GdcUeuhO6PwuPZnn++Y6oH2rLZc1d+5anZRikW470tnXitrXs5hsqG57
74KiSFa+v+Uj1kqU4Gjt0QDSfmQc185Wn5xieHPpZrcjDaut+N4t06+MDMcH7fjk
6nJ+tvo/dreZojA+AklljaNB2BioIGbEOGamnxOJ9Rjs0jV2d0A1c/6XBHDe+Xtu
SkWqvjdrLOSxAjErBpB97VYnYihjCDXfl+DIABOdumGO6hJz01DvbZ+VVLwGM0E=
=YH31
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull more x86 platform driver updates from Darren Hart:
"Move and add registration for the mlx-platform driver. Introduce
button and lid drivers for the surface3 (different from the
surface3-pro). Add BXT PMIC TMU support. Add Y700 to existing
ideapad-laptop quirk.
Summary:
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support"
* tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: surface3-wmi: Balance locking on error path
platform/x86: Add Whiskey Cove PMIC TMU support
platform/x86: ideapad-laptop: Add Y700 15-ACZ to no_hw_rfkill DMI list
platform/x86: Introduce button support for the Surface 3
platform/x86: Add custom surface3 platform device for controlling LID
platform/x86: mlx-platform: Add mlxcpld-hotplug driver registration
platform/x86: mlx-platform: Fix semicolon.cocci warnings
platform/x86: mlx-platform: Move module from arch/x86
This adds TMU (Time Management Unit) support for Intel BXT platform.
It enables the alarm wake-up functionality in the TMU unit of Whiskey Cove
PMIC.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[andy: resolve merge conflict in Kconfig]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver was
removed (got a "clean" driver for the same hardware through the netdev
tree), and some iio drivers were also dropped, but I think we ended up
adding a few thousand lines to the source tree in the end. Other than
that it's a lot of minor fixes all over the place, nothing major stands
out at all.
All of these have been in linux-next for a while. There will be a merge
conflict with Al's vfs tree in the lustre code, but the resolution for
that should be pretty simple, that too has been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAk1Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymikACg05b0h/iVTTH18474PXXnzw6jk9IAn0gI2fx9
cqp2MglTvphhrXzddL7V
=MeTw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here's the "big" staging/iio pull request for 4.10-rc1.
Not as big as 4.9 was, but still just over a thousand changes. We
almost broke even of lines added vs. removed, as the slicoss driver
was removed (got a "clean" driver for the same hardware through the
netdev tree), and some iio drivers were also dropped, but I think we
ended up adding a few thousand lines to the source tree in the end.
Other than that it's a lot of minor fixes all over the place, nothing
major stands out at all.
All of these have been in linux-next for a while. There will be a
merge conflict with Al's vfs tree in the lustre code, but the
resolution for that should be pretty simple, that too has been in
linux-next"
* tag 'staging-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1002 commits)
staging: comedi: comedidev.h: Document usage of 'detach' handler
staging: fsl-mc: remove unnecessary info prints from bus driver
staging: fsl-mc: add sysfs ABI doc
staging/lustre/o2iblnd: Fix misspelled attemps->attempts
staging/lustre/o2iblnd: Fix misspelling intialized->intialized
staging/lustre: Convert all bare unsigned to unsigned int
staging/lustre/socklnd: Fix whitespace problem
staging/lustre/o2iblnd: Add missing space
staging/lustre/lnetselftest: Fix potential integer overflow
staging: greybus: audio_module: remove redundant OOM message
staging: dgnc: Fix lines longer than 80 characters
staging: dgnc: fix blank line after '{' warnings.
staging/android: remove Sync Framework tasks from TODO
staging/lustre/osc: Revert erroneous list_for_each_entry_safe use
staging: slicoss: remove the staging driver
staging: lustre: libcfs: remove lnet upcall code
staging: lustre: remove set but unused variables
staging: lustre: osc: set lock data for readahead lock
staging: lustre: import: don't reconnect during connect interpret
staging: lustre: clio: remove mtime check in vvp_io_fault_start()
...
mmc host drivers, some existing drivers being extended to support new IP
versions and lots of other updates.
MMC core:
- Delete eMMC packed command support
- Introduce mmc_abort_tuning() to enable eMMC tuning to fail gracefully
- Introduce mmc_can_retune() to see if a host can be retuned
- Re-work and improve the sequence when sending a CMD6 for mmc
- Enable CDM13 polling when switching to HS and HS DDR mode for mmc
- Relax checking for CMD6 errors after switch to HS200
- Re-factoring the code dealing with the mmc block queue
- Recognize whether the eMMC card supports CMDQ
- Fix 4K native sector check
- Don't power off the card when starting the host
- Increase MMC_IOC_MAX_BYTES to support bigger firmware binaries
- Improve error handling and drop meaningless BUG_ONs()
- Lots of clean-ups and changes to improve the quality of the code
MMC host:
- sdhci: Fix tuning sequence and clean-up the related code
- sdhci: Add support to via DT override broken SDHCI cap register bits
- sdhci-cadence: Add new driver for Cadence SD4HC SDHCI variant
- sdhci-msm: Update clock management
- sdhci-msm: Add support for eMMC HS400 mode
- sdhci-msm: Deploy runtime/system PM support
- sdhci-iproc: Extend driver support to newer IP versions
- sdhci-pci: Add support for Intel GLK
- sdhci-pci: Add support for Intel NI byt sdio
- sdhci-acpi: Add support for 80860F14 UID 2 SDIO bus
- sdhci: Lots of various small improvements and clean-ups
- tmio: Add support for tuning
- sh_mobile_sdhi: Add support for tuning
- sh_mobile_sdhi: Extend driver to support SDHI IP on R7S72100 SoC
- sh_mobile_sdhi: remove support for sh7372
- davinci: Use mmc_of_parse() to enable generic mmc DT bindings
- meson: Add new driver to support GX platforms
- dw_mmc: Deploy generic runtime/system PM support
- dw_mmc: Lots of various small improvements
As a part of the mmc changes this time, I have also pulled in an immutable
branch/tag (soc-device-match-tag1) hosted by Geert Uytterhoeven, to share the
implementation of the new soc_device_match() interface. This is needed by the
below mmc related changes:
- mmc: sdhci-of-esdhc: Get correct IP version for T4240-R1.0-R2.0
- soc: fsl: add GUTS driver for QorIQ platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wGE2
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"It's been an busy period for mmc. Quite some changes in the mmc core,
two new mmc host drivers, some existing drivers being extended to
support new IP versions and lots of other updates.
MMC core:
- Delete eMMC packed command support
- Introduce mmc_abort_tuning() to enable eMMC tuning to fail
gracefully
- Introduce mmc_can_retune() to see if a host can be retuned
- Re-work and improve the sequence when sending a CMD6 for mmc
- Enable CDM13 polling when switching to HS and HS DDR mode for mmc
- Relax checking for CMD6 errors after switch to HS200
- Re-factoring the code dealing with the mmc block queue
- Recognize whether the eMMC card supports CMDQ
- Fix 4K native sector check
- Don't power off the card when starting the host
- Increase MMC_IOC_MAX_BYTES to support bigger firmware binaries
- Improve error handling and drop meaningless BUG_ONs()
- Lots of clean-ups and changes to improve the quality of the code
MMC host:
- sdhci: Fix tuning sequence and clean-up the related code
- sdhci: Add support to via DT override broken SDHCI cap register
bits
- sdhci-cadence: Add new driver for Cadence SD4HC SDHCI variant
- sdhci-msm: Update clock management
- sdhci-msm: Add support for eMMC HS400 mode
- sdhci-msm: Deploy runtime/system PM support
- sdhci-iproc: Extend driver support to newer IP versions
- sdhci-pci: Add support for Intel GLK
- sdhci-pci: Add support for Intel NI byt sdio
- sdhci-acpi: Add support for 80860F14 UID 2 SDIO bus
- sdhci: Lots of various small improvements and clean-ups
- tmio: Add support for tuning
- sh_mobile_sdhi: Add support for tuning
- sh_mobile_sdhi: Extend driver to support SDHI IP on R7S72100 SoC
- sh_mobile_sdhi: remove support for sh7372
- davinci: Use mmc_of_parse() to enable generic mmc DT bindings
- meson: Add new driver to support GX platforms
- dw_mmc: Deploy generic runtime/system PM support
- dw_mmc: Lots of various small improvements
As a part of the mmc changes this time, I have also pulled in an
immutable branch/tag (soc-device-match-tag1) hosted by Geert
Uytterhoeven, to share the implementation of the new
soc_device_match() interface. This is needed by these mmc related
changes:
- mmc: sdhci-of-esdhc: Get correct IP version for T4240-R1.0-R2.0
- soc: fsl: add GUTS driver for QorIQ platforms"
* tag 'mmc-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (136 commits)
mmc: sdhci-cadence: add Cadence SD4HC support
mmc: sdhci: export sdhci_execute_tuning()
mmc: sdhci: Tidy tuning loop
mmc: sdhci: Simplify tuning block size logic
mmc: sdhci: Factor out tuning helper functions
mmc: sdhci: Use mmc_abort_tuning()
mmc: mmc: Introduce mmc_abort_tuning()
mmc: sdhci: Always allow tuning to fall back to fixed sampling
mmc: sdhci: Fix tuning reset after exhausting the maximum number of loops
mmc: sdhci: Fix recovery from tuning timeout
Revert "mmc: sdhci: Reset cmd and data circuits after tuning failure"
mmc: mmc: Relax checking for switch errors after HS200 switch
mmc: sdhci-acpi: support 80860F14 UID 2 SDIO bus
mmc: sdhci-of-at91: remove bogus MMC_SDHCI_IO_ACCESSORS select
mmc: sdhci-pci: Use ACPI to get max frequency for Intel NI byt sdio
mmc: sdhci-pci: Add PCI ID for Intel NI byt sdio
mmc: sdhci-s3c: add spin_unlock_irq() before calling clk_round_rate
mmc: dw_mmc: display the clock message only one time when card is polling
mmc: dw_mmc: add the debug message for polling and non-removable
mmc: dw_mmc: check the "present" variable before checking flags
...
Rework the IRQ handler by using HW IRQ number and status bit.
Each HW IRQ number is matched with TPS65217 register layout[*].
(USB IRQ number is 0, AC is 1, Push button is 2)
When an interrupt is enabled, mask bit should be cleared (unmasked).
If an interrupt is disabled, then mask bit should be set (masked).
This mask value is updated into the TPS65217 register in irq_sync_unlock().
Mask bit and interrupt status bit can be handled with HW IRQ number.
Eventually, additional IRQ data, 'tps65217_irqs[]' and the function,
'irq_to_tps65217_irq()' are not necessary.
[*] TPS65217 interrupt register layout
Bit7 6 5 4 3 2 1 0
----------------------------------------------
| x | PBM | ACM | USBM | x | PBI | ACI | USBI
PBM: Push button status change interrupt mask
ACM: AC interrupt mask
USBM: USB power status change interrupt mask
PBI: Push button status change interrupt
ACI: AC power status change interrupt
USBI: USB power status change interrupt
x: Not used
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 interrupt register includes read/writeable mask bits with
read-only status bits. (bit 4, 5, 6 are R/W, bit 0, 1, 2 are RO)
And reserved bit is not required.
Register update operation is preferred for disabling all interrupts during
the device initialisation.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP806 supports either master/standalone or slave mode.
Slave mode allows sharing the serial bus, even with multiple
AXP806 which all have the same hardware address.
This is done with extra "serial interface address extension",
or AXP806_BUS_ADDR_EXT, and "register address extension", or
AXP806_REG_ADDR_EXT, registers. The former is read-only, with
1 bit customizable at the factory, and 1 bit depending on the
state of an external pin. The latter is writable. Only when
the these device addressing bits (in the upper 4 bits of the
registers) match, will the device respond to operations on
its other registers.
Add these 2 registers to the regmap so we can access them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mach/hardware.h is needed on C source code side, not header.
And struct davinci_vc is duplicated definition.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DEV_OFF and DEV_OFF_RST functions for RK808 are designed error that
only DEV_OFF_RST can power off supplies. RK818 has been fixed this
issue, so that DEV_OFF is used to power off supplies.
Signed-off-by: Jianhong Chen <chenjh@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building with extra warnings enabled, most files including
linux/mfd/tps65912.h warn about a static variable defined in the
header:
include/linux/mfd/tps65912.h:331:35: warning: 'tps65912_regmap_config' defined but not used [-Wunused-const-variable=]
We also duplicate the data structure between the i2c and spi front-end
drivers. Moving it into the driver code avoids the warning and
the duplication.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. For now, only the ADC and the thermal
sensor drivers are probed by the MFD, the touchscreen controller support
will be added later.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adding support to configure regulator POK mapping bit
to control nRST_IO and GPIO1 POK function.
In tegra based platform which uses MAX20024 pmic, when
some of regulators are configured FPS_NONE(flexible power sequencer)
causes PMIC GPIO1 to go low which lead to various other rails turning off,
to avoid this MPOK bit of those regulators need to be set to 0
so that PMIC GPIO1 will not go low.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
AXP22x has also some different register map than axp20x, they're also
added here.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enum value of 'tps65217_irq_type' is not matched with DT parsed hwirq
number[*].
The MFD driver gets the IRQ data by referencing hwirq, but the value is
different. So, irq_to_tps65217_irq() returns mismatched IRQ data.
Eventually, the power button driver enables not PB but USB interrupt
when it is probed.
According to the TPS65217 register map[**], USB interrupt is the LSB.
This patch defines synchronized IRQ value.
[*] include/dt-bindings/mfd/tps65217.h
[**] http://www.ti.com/lit/ds/symlink/tps65217.pdf
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the required pieces to ti_am335x_adc driver for
DMA support
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
store the physical address of the device in its priv to use it
for DMA addressing in the client drivers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove all the individual compatibles for all the regulators
and introduce id_table and update the driver accordingly
to parse device tree nodes using the regulator framework.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently read directly calls the repmap read function. Hence
remove the redundant wrapper and use regmap read wherever
needed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the EC_CMD_GET_FEATURES message to check the supported features for
each MCU.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
[tomeu: adapted to changes in mainline]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[enric: remove references to USB PD feature and do it more generic]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
For the MFD changes:
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the core functions to be able to support the sensors attached behind
the ChromeOS Embedded Controller and used by other IIO cros-ec sensor
drivers.
The cros_ec_sensor_core driver matches with current driver in ChromeOS
4.4 tree, so it includes all the fixes at the moment. The support for
this driver was made by Gwendal Grignou. The original patch and all the
fixes has been squashed and rebased on top of mainline.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
[eballetbo: split, squash and rebase on top of mainline the patches
found in ChromeOS tree]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJX9giOAAoJEFGvii+H/Hdh8aEP/iiHosBZsksZ4we8KAdoXkxi
x5nnJvS9+4b5yaasSiN8e2xs9YMOlHu1CNZDZ3RJZ+rLusdVeg5ju5p5WED83pvi
ltiPMhyqruM3d0rieTRHxeJFmmEf2exwKV3Y+5lo9586dFfJrmGp2AxScId4TtwP
CcsjwYRx/WvVfWrv1xWsjd9b1RDlWglt3dcVhdKAQbvPPOy5O4ymXNMFs0DuFyZ+
2A16sw7hdYenXSvAHlZzS5IqXP9JEeosu3O/mUUZKF3PO55t+KbQBGZiwXoal4gp
1dwrdBjlrZaHcDa5Ra9x+jQ2kxIkyUT44CXKAHa7llTfZQkZIgnv/fWUhB8C5JxU
iaqnN9rWQ2MNjt3Us/n1TSJH2kEnSNbzrQixE0n8yjIBsZePWlW2ZpWYRF7GPG2i
2pB8oNz/NdDkKWdosR3ArnseNOKVcC+GtD+mHk0aKMPghPq+gDIRrdM0CFyWeIZE
w/Cf+HHZPR0O1VuYZ9bHIhbgnEbz5xUADOtBAdppIBQiNEI/G9lJpG6Ft4FTQoPi
CIbnnB/wxxMaEl85rUPYGkxQniuUI5f0tMv3k2ZtAZMKcqn6iXtiIOuXceM2vUdy
ze1uddH4HuHLcrJT5x+J72XJL6RXzZKxOqd0b7BcXnvMVFJrWgleH1JQ2WqazAEW
il1u28IkFusm/BW/0dps
=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
This function is only used in a single place and no new users will be
added as all the devices other required GPIOs are already handled. As
such just merge the code back into the calling function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
The McPDM in OMAP4/5 is using the pdmclk from twl6040 as functional clock.
The twl6040-pdmclk driver provides a clock which can be used to make sure
that the pdmclk is active when the McPDM is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Due to the lack of parity in the way array fields have been named/
numbered, a mistake was made where more debug fields were declared
than actually existed. In doing so, 2 fields were added, which
although unclear, were already declared in the array. The result
was that the latter declarations trashed the former ones.
This patch places the array back in the correct order and removes
the offending NULL entries.
While we're at it, let's ensure this doesn't happen again by naming
each field properly and add a new *_LAST define to describe how
many fields there should be.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When building with -Woverride-init, we get a warning about an incorrect
initializer:
drivers/mfd/rk808.c:244:8: error: initialized field overwritten [-Werror=override-init]
[RK818_IRQ_DISCHG_ILIM] = {
This is clearly a mistake, as both RK818_IRQ_DISCHG_ILIM and RK818_IRQ_USB_OV
are defined as '7', but they refer to different register bits. Changing
RK818_IRQ_DISCHG_ILIM to 15 is consistent with how all other 14 interrupts are
handled here, so I'm assuming this is what it should have been.
Fixes: 2eedcbfc06 ("mfd: rk808: Add RK818 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for handling IRQs: power button, AC and USB power state
changes. Mask and interrupt bits are shared within one register, which
prevents us to use regmap_irq implementation. New irq_domain is created in
order to add interrupt handling for each tps65217's subsystem. IRQ
resources have been added for charger subsystem to be able to notify about
AC and USB state changes.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds common driver for the Top block of the Samsung Exynos
SoC Low Power Audio Subsystem. This is a minimal driver which prepares
resources for IP blocks like I2S, audio DMA and UART and exposes
a regmap for the Top block registers. Also system power ops are added
to ensure the Audio Subsystem is operational after system suspend/resume
cycle.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
set_bit() and clear_bit() take the bit number so this code is really
doing "1 << (1 << irq)" which is a double shift bug. It's done
consistently so it won't cause a problem unless "irq" is more than 4.
Fixes: 70c6cce040 ('mfd: Support 88pm80x in 80x driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove incorrect e-mail addresses from the copyright header and
MODULE_AUTHOR() macro. These e-mail addresses are no longer in use.
The author names have not been changed, only the e-mail addresses have
been deleted from the source files.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds requesting of the clocks supplied on MCLK1, MCLK2 pins,
gating of the 32k clock is added to the arizona_clk32k_enable(),
arizona_clk32k_disable() helpers.
It's a temporary change until the CODEC's clock controller gets exposed
through the clk API and is helpful for board configurations where the
MCLK clocks are not provided by always on oscillators.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The HTC GPIO driver is a pure GPIO driver and I just can not
see what it is doing inside MFD. Let's just move it to GPIO
and take this opportunity to move the platform data to
<linux/platform_data/gpio-htc-egpio.h>
Cc: arm@kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The X-Powers AXP806 is a new PMIC that is paired with Allwinner's A80
SoC, along with a master AXP809 PMIC.
This PMIC has a new register layout, and supports some functions not
seen in other X-Powers PMICs, such as master-slave mode, or having
multiple AXP806 PMICs on the same bus with address space extension,
or supporting both I2C and RSB mode. I2C has not been tested.
This patch adds support for the interrupts of the PMIC. A regulator
sub-device is enabled, but actual regulator support will come in a
later patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here are a number of small fixes for staging and IIO drivers that
resolve reported problems.
Full details are in the shortlog. All of these have been in linux-next
with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfK4HoPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspt0MAn0wC
dYhZOUHxOptLiEkVGXFCU9kzAJ4gETEbuGn9lgp2TFATOOAN7oqPUw==
=6MKk
-----END PGP SIGNATURE-----
Merge tag 'staging-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a number of small fixes for staging and IIO drivers that
resolve reported problems.
Full details are in the shortlog. All of these have been in
linux-next with no reported issues"
* tag 'staging-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (35 commits)
arm: dts: rockchip: add reset node for the exist saradc SoCs
arm64: dts: rockchip: add reset saradc node for rk3368 SoCs
iio: adc: rockchip_saradc: reset saradc controller before programming it
iio: accel: kxsd9: Fix raw read return
iio: adc: ti_am335x_adc: Increase timeout value waiting for ADC sample
iio: adc: ti_am335x_adc: Protect FIFO1 from concurrent access
include/linux: fix excess fence.h kernel-doc notation
staging: wilc1000: correctly check if associatedsta has not been found
staging: wilc1000: NULL dereference on error
staging: wilc1000: txq_event: Fix coding error
MAINTAINERS: Add file patterns for ion device tree bindings
MAINTAINERS: Update maintainer entry for wilc1000
iio: chemical: atlas-ph-sensor: fix typo in val assignment
iio: fix sched WARNING "do not call blocking ops when !TASK_RUNNING"
staging: comedi: ni_mio_common: fix AO inttrig backwards compatibility
staging: comedi: dt2811: fix a precedence bug
staging: comedi: adv_pci1760: Do not return EINVAL for CMDF_ROUND_DOWN.
staging: comedi: ni_mio_common: fix wrong insn_write handler
staging: comedi: comedi_test: fix timer race conditions
staging: comedi: daqboard2000: bug fix board type matching code
...
The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
- Battery support
Both RK808 and RK818 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP873X chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Configurable General Purpose Output Signals (GPO).
PMIC interacts with the main processor through i2c. PMIC has
couple of LDOs (Linear Regulators), couple of BUCKs (Step-Down DC-DC
Converter Cores) and GPOs (General Purpose Output Signals).
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer revisions of the ChromeOS EC add more events besides the keyboard
ones. So handle interrupts in the MFD driver and let consumers register
for notifications for the events they might care.
To keep backward compatibility, if the EC doesn't support MKBP event, we
fall back to the old MKBP key matrix host command.
Cc: Randall Spangler <rspangler@chromium.org>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that open delay and sample delay for each channel is configurable
via DT, the default IDLE_TIMEOUT value is not enough as this is
calculated based on hardcoded macros. This results in driver returning
EBUSY sometimes. Fix this by increasing the timeout
value based on maximum value possible to open delay and sample delays
for each channel.
Fixes: 5dc11e8106 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Create a new header file for TI DA8XX SoC CFGCHIPx registers.
This will be used by a number of planned drivers including a new USB
PHY driver and common clock framework drivers.
The same defines *will* be removed from the platform_data header,
once all the users start using the new syscon device header.
This also fixes the following compiler error caused due to
a dependent patch not merged.
drivers/phy/phy-da8xx-usb.c:19:37:
fatal error: linux/mfd/da8xx-cfgchip.h: No such file or directory
#include <linux/mfd/da8xx-cfgchip.h>
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some versions of tps65218 do not seem to support poweroff modes properly
if DCDC3 regulator is shut-down. Thus, keep it enabled even during
poweroff if the version info matches the broken silicon revision.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Version information will be needed to handle some error cases under the
regulator driver, so store the information once during MFD probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly
This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AC100 is a multifunction device with an audio codec subsystem and
an RTC subsystem. These two subsystems share a common register space
and host interface.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
- New API to call bespoke pre/post IRQ handlers; Regmap
- New Device Support
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
- New Functionality
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
- Fix-ups
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
- Bug Fixes
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KB2d
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- New API to call bespoke pre/post IRQ handlers; Regmap
New Device Support:
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
New Functionality:
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
Fix-ups:
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
Bug Fixes:
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic"
* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: qcom_rpm: Parametrize also ack selector size
mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
mfd: hi655x: Fix return value check in hi655x_pmic_probe()
mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
mfd: twl-core: Refactoring for add_numbered_child()
mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
mfd: arizona: Add missing disable of PM runtime on probe error path
mfd: stmpe: Move platform data into MFD driver
mfd: max14577: Allow driver to be built as a module
mfd: max14577: Use module_init() instead of subsys_initcall()
mfd: arizona: Remove some duplicate defines
mfd: qcom_rpm: Remove unused define
mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
mfd: hi655x-pmic: Rename some interrupt macro names
mfd: hi655x-pmic: Fixup issue with un-acked interrupts
mfd: arizona: Check if AOD interrupts are pending before dispatching
mfd: qcom_rpm: Fix offset error for msm8660
...
Majority of this update is about ASoC, including a few new drivers,
and the rest are mostly minor changes. The only substantial change in
ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and bug
fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002, Broadcom
Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960 and MAX98504,
Realtek RT5514 and Wolfson WM8758
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zx3K
-----END PGP SIGNATURE-----
Merge tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of this update is about ASoC, including a few new
drivers, and the rest are mostly minor changes. The only substantial
change in ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and
bug fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002,
Broadcom Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960
and MAX98504, Realtek RT5514 and Wolfson WM8758"
* tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (278 commits)
sound: oss: Use kernel_read_file_from_path() for mod_firmware_load()
ASoC: Intel: Skylake: Delete an unnecessary check before the function call "release_firmware"
ASoC: Intel: Skylake: Fix NULL Pointer exception in dynamic_debug.
ASoC: samsung: Specify DMA channels through struct snd_dmaengine_pcm_config
ASoC: samsung: Fix error paths in the I2S driver's probe()
ASoC: cs53l30: Fix bit shift issue of TDM mode
ASoC: cs53l30: Fix a bug for TDM slot location validation
ASoC: rockchip: correct the spdif clk
ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members
ASoC: rsrc-card: use asoc_simple_card_parse_card_name()
ASoC: rsrc-card: use asoc_simple_dai instead of rsrc_card_dai
ASoC: rsrc-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card: use asoc_simple_card_parse_card_name()
ASoC: simple-card-utils: add asoc_simple_card_parse_card_name()
ASoC: simple-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card-utils: add asoc_simple_card_set_dailink_name()
ASoC: nau8825: drop redundant idiom when converting integer to boolean
ASoC: nau8825: jack connection decision with different insertion logic
ASoC: mediatek: Add HDMI dai-links to the mt8173-rt5650 machine driver
ASoC: mediatek: mt2701: fix non static symbol warning
...
The EC_CMD_PWM_{GET,SET}_DUTY commands allow us to control a PWM that is
attached to the EC, rather than the main host SoC. The API provides
functionality-based (e.g., keyboard light, backlight) or index-based
addressing of the PWM(s). Duty cycles are represented by a 16-bit value,
where 0 maps to 0% duty cycle and U16_MAX maps to 100%. The period
cannot be controlled.
This command set is more generic than, e.g.,
EC_CMD_PWM_{GET,SET}_KEYBOARD_BACKLIGHT and could possibly used to
replace it on future products.
Let's update the command header to include the definitions.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
So that callers of cros_ec_cmd_xfer() don't have to repeat boilerplate
code when checking for errors from the EC side.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Except for the constant DB8500_PRCMU_FW_VERSION_OFFSET number, nothing
is ever passed through the platform data and used in a driver, so we
can simply stop passing it around.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix compiler warning caused by an uninitialised variable inside
da9052_group_write() function. Defaulting the value to zero covers
the trivial case.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On some boards, like omap5-uevm the MCLK is gated by default and in order
to be able to use the High performance modes of twl6040 it need to be
enabled by SW.
Add support for handling the MCLK source clock via CCF.
At the same time lower the print priority of the notification that the 32K
clock is not provided and it is not going to be handled by the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The STMPE platform data is only populated from the device tree
in all existing users, so push the struct and make the OF case
the norm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some duplicate defines seem to have snuck into the registers file, this
patch simply removes them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the hi655x-pmic driver has names for interrupt mask
values, but not for the interrupt numbers themselves.
So to allow for interrupt numbers to have sane names, rename
the mask values with the _MASK postfix and use the existing
names as the interrupt name
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap structure pointer is named regmap_tscadc, this is not
consistent with other drivers and is redundant, it also contributes
to several checkpatch warnings involving long lines. Rename this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the Altera Arria10 Development Kit System Resource
chip which is implemented using a MAX5 as a external gpio extender
with the regmap framework over a SPI bus.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Extend the driver to support Ricoh RN5T567. Support the additional
DCDC and slightly different voltage range of LDORTC1.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4
+ Slightly different output voltage/currents
+ 32kHz Output
- ADC/Charger capabilities
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65218 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator has sequence registers and every regulator has a default
strobe value and gets disabled when a particular power down sequence
occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TPS65217 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator of tps65217 PMIC has sequence registers and every
regulator has a default strobe value and gets disabled when a particular
power down sequence occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Enhanced commit log and added dynamic allocation for strobes]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a notifier chain that can be used from the machine driver to catch
events generated by the CODEC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A handful of changes this merge window:
- A few patches to fix probing and configuration of pstore
- A few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and addition
of compat_ioctl support.
- Keyboard backlight control support
There was also an accidential duplicate registration of trackpads on 'Leon',
which was reverted just recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXSb5tAAoJEIwa5zzehBx38BsQAI+p6urzboC2+NSsZAq72d4/
u2SF+ziEdgj4f7n38TjiDaFTqig9nqoQeB2nDCRicyEcHsCiK/ghsdq4ULfkvHIa
VALn/rBkQWQ7hC+2tfrQn7Rd2VqVnh28+EyhGezhVtrAGRaE2jIbgKnnfD3MS+b5
lab014HBppP1pDtJQQYCcoCpOUF1a9WEb8jKPWf4DCeCMaSrwFLKxV5VeqDkNtEZ
a3GFzB+WypN1nwBQ7PEOUxutzsUakSNy+RFoCqGwVppJ+kA/E3MO2BGoEJuQ6LXP
u7nyabJq6zBQAlrYie4OoiijBWQ+Q759jbOKkmxpBfL/mtMMepV05DIx/16Yi9NY
j+4A9HsuY+EYUhr0mH7B57CH0RClebixdZ62DtUK0Fe6H66SsMZPYtTKLIzOTzgO
j+gypQyW8BvcM/XjPYTA/vlYK45IJYB5OUDQzFW0qWQv/nInoYOS3G8IVooKHMDy
+s2wih/OAxBCDJ+KfDeJUj3U5Avz1YCojRraZWmBsOPpRpsQHVQ02r3uoHeHHZFv
bI8sTJ7BGxoYX5Kb6+xbtW7SnXoWZN8vlqdCpdNnLWKcwIqHKFirkoZh2N2AqyZB
7VpQW1HD2WxYBpxMv98KVyPiR+5xCnZnpqcIIvpGrX00KhmJkMgIT4FbWHMf6vVt
T55Sz5V9z/dsgMSDT3LY
=bcc4
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson
"A handful of Chrome driver and binding changes this merge window:
- a few patches to fix probing and configuration of pstore
- a few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and
addition of compat_ioctl support.
- keyboard backlight control support
There was also an accidential duplicate registration of trackpads on
'Leon', which was reverted just recently"
* tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
Revert "platform/chrome: chromeos_laptop: Add Leon Touch"
platform/chrome: chromeos_laptop - Add Elan touchpad for Wolf
platform/chrome: chromeos_laptop - Add elan trackpad option for C720
platform/chrome: cros_ec_dev - Populate compat_ioctl
platform/chrome: cros_ec_lightbar - use name instead of ID to hide lightbar attributes
platform/chrome: cros_ec_dev - Fix security issue
platform/chrome: Add Chrome OS keyboard backlight LEDs support
platform/chrome: use to_platform_device()
platform/chrome: pstore: Move to larger record size.
platform/chrome: pstore: probe for ramoops buffer using acpi
platform/chrome: chromeos_laptop: Add Leon Touch
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXOao7AAoJECTWi3JdVIfQ3EQH/1Z4nukvcOeZgVN/4K9b27t2
LYSyPH4+7XiDsi24UAyxZWls625t+1XRtolS0yHYY+IMObkeH/T+StTirDG4C1Mv
0uw/lEs5XmkSPFMad2fDcVXhf+D6EsvuLZ24qLKhoi8TyePv6GRvYapitE4dAI7Z
bBwjT+f9r1qSMJvfCmqit8zDneDFMKd7oqPmBW6NpFri5/ksn1KUnd/zOGu2SlSd
R01Oa2VbRDGj8/Zzu5MORvgLLucxTqtAFYeF3T52M5oc33IBWvbha4fk/BDOswbz
H9S3vHyakmbZgXnnGMTp4qz0bxA76YaHzjtqgGUEMbigHTsB0PP5TtII3i5LkaY=
=Zsr1
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.7' into asoc-linus
ASoC: Updates for v4.7
The updates this time around are almost all driver code:
- Further slow progress on the topology code.
- Substantial updates and improvements for the da7219, es8328, fsl-ssi
Intel and rcar drivers.
# gpg: Signature made Mon 16 May 2016 12:08:43 BST using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of other
stuff.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0P8ACgkQMUfUDdst+ykkFQCg0kJlxIiCU1FYBZYriqo4vX3F
9N8AoM/8nO8Y6vMpF2LWnamafYgqscTE
=ZuCh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big pull request for USB and PHY drivers for 4.7-rc1
Full details in the shortlog, but it's the normal major gadget driver
updates, phy updates, new usbip code, as well as a bit of lots of
other stuff.
All have been in linux-next with no reported issues"
* tag 'usb-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (164 commits)
USB: serial: ti_usb_3410_5052: add MOXA UPORT 11x0 support
USB: serial: fix minor-number allocation
USB: serial: quatech2: fix use-after-free in probe error path
USB: serial: mxuport: fix use-after-free in probe error path
USB: serial: keyspan: fix debug and error messages
USB: serial: keyspan: fix URB unlink
USB: serial: keyspan: fix use-after-free in probe error path
USB: serial: io_edgeport: fix memory leaks in probe error path
USB: serial: io_edgeport: fix memory leaks in attach error path
usb: Remove unnecessary space before operator ','.
usb: Remove unnecessary space before open square bracket.
USB: FHCI: avoid redundant condition
usb: host: xhci-rcar: Avoid long wait in xhci_reset()
usb/host/fotg210: remove dead code in create_sysfs_files
usb: wusbcore: Do not initialise statics to 0.
usb: wusbcore: Remove space before ',' and '(' .
USB: serial: cp210x: clean up CRTSCTS flag code
USB: serial: cp210x: get rid of magic numbers in CRTSCTS flag code
USB: serial: cp210x: fix hardware flow-control disable
USB: serial: option: add even more ZTE device ids
...
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
Enumeration
Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
Provide common functions for ECAM mapping (Jayachandran C)
Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
Add Downstream Port Containment portdrv service type (Keith Busch)
Add Downstream Port Containment driver (Keith Busch)
Resource management
Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug
acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization
Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU
Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
Add support for multiple DMA aliases (Jacek Lawrynowicz)
Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt
Fix double free of drom buffer (Andreas Noever)
Add Intel Thunderbolt device IDs (Lukas Wunner)
Fix typos and magic number (Lukas Wunner)
Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver
Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver
Don't clobber read-only bits in bridge config registers (David Daney)
Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver
Use enum instead of bool for variant indicator (Andrey Smirnov)
Implement reset sequence for i.MX6+ (Andrey Smirnov)
Factor out ref clock enable (Bjorn Helgaas)
Add initial imx6sx support (Christoph Fritz)
Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
Add DT property for link gen, default to Gen1 (Tim Harvey)
dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver
add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver
Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver
Report resources release after stopping the bus (Vitaly Kuznetsov)
Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver
Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver
Add error IRQ handler (Murali Karicheri)
Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous
Fix spelling errors (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=68Iz
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
- Provide common functions for ECAM mapping (Jayachandran C)
- Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
- Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
- Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
- Add Downstream Port Containment portdrv service type (Keith Busch)
- Add Downstream Port Containment driver (Keith Busch)
Resource management:
- Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
- Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
- alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
- Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
- Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug:
- acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
- Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization:
- Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
- Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
- Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU:
- Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
- Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
- Add support for multiple DMA aliases (Jacek Lawrynowicz)
- Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt:
- Fix double free of drom buffer (Andreas Noever)
- Add Intel Thunderbolt device IDs (Lukas Wunner)
- Fix typos and magic number (Lukas Wunner)
- Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver:
- Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver:
- Don't clobber read-only bits in bridge config registers (David Daney)
- Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver:
- Use enum instead of bool for variant indicator (Andrey Smirnov)
- Implement reset sequence for i.MX6+ (Andrey Smirnov)
- Factor out ref clock enable (Bjorn Helgaas)
- Add initial imx6sx support (Christoph Fritz)
- Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
- Add DT property for link gen, default to Gen1 (Tim Harvey)
- dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
- dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver:
- add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
- Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver:
- Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
- Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver:
- Report resources release after stopping the bus (Vitaly Kuznetsov)
- Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver:
- Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
- Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver:
- Add error IRQ handler (Murali Karicheri)
- Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous:
- Fix spelling errors (Colin Ian King)"
* tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
PCI: hv: Add explicit barriers to config space access
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
PCI: designware: Remove incorrect RC memory base/limit configuration
PCI: hv: Report resources release after stopping the bus
ARM: dts: imx6qp: Specify imx6qp version of PCIe core
PCI: imx6: Implement reset sequence for i.MX6+
PCI: imx6: Use enum instead of bool for variant indicator
PCI: thunder: Don't clobber read-only bits in bridge config registers
thunderbolt: Fix double free of drom buffer
PCI: rcar: Select PCI_MSI_IRQ_DOMAIN
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
...
Disconnect also the path to AUXL from the HF path during digital_mute to
avoid pop noise leakage to Line-out pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PMIC MFD driver to support hisilicon hi665x.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Just one commit reworking the handling of built-in properties
initialization and updating a few drivers in accordance with the
core framework changes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJXOjO2AAoJEILEb/54YlRxiksP/jJjZZ5B7r7iBCLhtornA9L4
I54t0X4HcxmkBd2k5VxBE8k0bzMo/Tx52Bm/YnKxKQS7CSVPr7Lhrj3pH2NoQO5i
S5T4Wdi8AYK/0LXcCwEfyMCAr7M9mstc+v2mQu1ZPtGKSI/c9+3r3zCrtSbxjwK8
RU4RSa3Y27drL8wbyc2PvjytYcbmwM4BsLOL8v4noUe2WussN4LEjiN3q4Y+s6O8
gmSPCZDY5Qg1Nc1YBse+lPsHHUng9cgIHzAnQkN5CnM36KLoNG3KaYGu+0ZxSnMe
Ed+NaCZZC+u43r7vaJaOpnE+1jxYLOw4w7ail6GHveaI1EYKUtaRF8KcUDn1wwkU
MxYslt5i8LS0ar2DPJ/RgHZ2ajaZAPjdie/+PJQwO6e5PqQsCDOLia8zWTS6HEMf
DTirJrRfy2o1QR693I8MSwm5hsFiOPTeYXexWxLAe+LtUN277qaZrFAp7DSSEKm1
p53K9xaWmd2gJUTsmnim0TlTA2j9PO9dCJeXJDBa2B6QR11oQ160BvZ6/kk5U/FZ
/XSbixwvRs2i6H/lVNgqyGmJdIAt75HcCUwNw4QI76nHrxx1BirA2DNbrGAlsNAF
eBYaZ7pYtUN4/nZh+jYJWki7pY46F/7OgGoQQzM2LR6W8dz7Cwt/OQyt0+ekLhN4
prNP1Br++rFeCIc7kFOk
=O8T9
-----END PGP SIGNATURE-----
Merge tag 'device-properties-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties update from Rafael Wysocki:
"Generic device properties framework update.
Just one commit reworking the handling of built-in properties
initialization and updating a few drivers in accordance with the core
framework changes"
* tag 'device-properties-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: don't bother the drivers with struct property_set
- Add TRACE support to be able to debug request flow
- Extend/improve reset support for (e)MMC
- Convert MMC pwrseq to platform device drivers
- Use IDA for indexes
- Some additional minor improvements
MMC host:
- sdhci: Re-factoring, clean-ups and improvements
- sdhci-acpi|pci: Use MMC_CAP_AGGRESSIVE_PM for Broxton
- omap/omap_hsmmc: Convert to use dma_request_chan()
- usdhi6rol0: Add support for UHS modes
- sh_mmcif: Update runtime PM support
- tmio: Wolfram Sang steps in as maintainer
- tmio: Add UHS-I mode support
- sh_mobile_sdhi: Add UHS-I mode support
- tmio/sdhi: Re-factoring, clean-ups and improvements
- dw_mmc: Re-factoring and clean-ups
- davinci: Convert to use dma_request_chan()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=89kT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.7' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add TRACE support to be able to debug request flow
- Extend/improve reset support for (e)MMC
- Convert MMC pwrseq to platform device drivers
- Use IDA for indexes
- Some additional minor improvements
MMC host:
- sdhci: Re-factoring, clean-ups and improvements
- sdhci-acpi|pci: Use MMC_CAP_AGGRESSIVE_PM for Broxton
- omap/omap_hsmmc: Convert to use dma_request_chan()
- usdhi6rol0: Add support for UHS modes
- sh_mmcif: Update runtime PM support
- tmio: Wolfram Sang steps in as maintainer
- tmio: Add UHS-I mode support
- sh_mobile_sdhi: Add UHS-I mode support
- tmio/sdhi: Re-factoring, clean-ups and improvements
- dw_mmc: Re-factoring and clean-ups
- davinci: Convert to use dma_request_chan()"
* tag 'mmc-v4.7' of git://git.linaro.org/people/ulf.hansson/mmc: (99 commits)
mmc: mmc: Fix partition switch timeout for some eMMCs
mmc: sh_mobile_sdhi: enable SDIO IRQs for RCar Gen3
mmc: sdio: fall back to SDIO 1.0 for broken 1.1 cards
mmc: sdhci-st: correct name of sd-uhs-sdr50 property
MAINTAINERS: update entry for TMIO MMC driver
mmc: block: improve logging of handling emmc timeouts
mmc: sdhci: removed unneeded function wrappers
mmc: core: remove the invalid message in mmc_select_timing
mmc: core: fix using wrong io voltage if mmc_select_hs200 fails
mmc: sdhci-of-arasan: fix set_clock when a phy is supported
mmc: omap: Use dma_request_chan() for requesting DMA channel
mmc: mmc: Attempt to flush cache before reset
mmc: sh_mobile_sdhi: check return value when changing clk
mmc: sh_mobile_sdhi: only change the clock on RCar Gen2+
mmc: tmio/sdhi: introduce flag for RCar 2+ specific features
mmc: sh_mobile_sdhi: make clk_update function more compact
mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel
mmc: sdhci-of-at91: add presets setup
mmc: usdhi6rol0: add pinctrl to set pin drive strength
mmc: usdhi6rol0: add support for UHS modes
...
Prevent memory scribble by checking that ioctl buffer size parameters
are sane.
Without this check, on 32 bits system, if .insize = 0xffffffff - 20 and
.outsize the amount to scribble, we would overflow, allocate a small
amounts and be able to write outside of the malloc'ed area.
Adding a hard limit allows argument checking of the ioctl. With the
current EC, it is expected .insize and .outsize to be at around 512 bytes
or less.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
MAX77620/MAX20024 are Power Management IC from the MAXIM.
It supports RTC, multiple GPIOs, multiple DCDC and LDOs,
watchdog, clock etc.
Add MFD drier to provides common support for accessing the
device; additional drivers is developed on respected subsystem
in order to use the functionality of the device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There was a static checker warning in wm8400_reg_read() because we were
returning u16 and that can't hold the negative error codes. The
function isn't used, so let's just delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On mx6ul the General Purpose Register 1 (GPR1) contains the following
bits for configuring the direction of the SAI MCLKs:
SAI1_MCLK_DIR, SAI2_MCLK_DIR, SAI3_MCLK_DIR
Introduce the "fsl,sai-mclk-direction-output" optional property to allow
configuring the SAI_MCLK outputs.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RCar Gen2 and later implementations of TMIO/SDHI have their own set of
features and additions. FAST_CLK_CHG is just one of them and I see a few
others being added soon. Some may work on older chipsets but this needs
to be tested case by case. Instead of adding a bunch of flags for each
feature, add a global RCar2+ one for now. We can still break out
features if the need arises.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I.MX6+ has a dedicated bit for resetting PCIe core, which should be used
instead of a regular reset sequence since using the latter will hang the
SoC.
This commit is based on c34068d48273e24d392d9a49a38be807954420ed from
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Marek Szyprowski