Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch adds support for hardware that returns resource ids via
extents rather than contiguous ranges.
[jejb: checkpatch.pl fixes]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Debugfs enhancements
- Added iDiag support for new adapters.
- Added queue entry access methods.
- Fix host/port index in decimal
- Added Doorbell register access methods.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Periodically poll adapter registers to detect pci adapter failure
(reads return -1). On failure, take port offline, set error indicators
and wake up worker threads. Threads will take adapter offline.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the driver debugfs framework for supporting debugfs read and write
operations, and iDiag command structure.
- Add read and write to SLI4 device PCI config space registers.
- Add the driver support of debugfs PCI config space register bits set/clear
methods to the provided bitmask.
- Add iDiag driver support for SLI4 device queue diagnostic.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Make link speed not supported by port message an error message.
- Add support for new SLI failure codes add sysfs parameter to reflect the
security setting and current state.
- Add all lpfc module parameters to the /sys/modules/lpfc/parameters directory.
[jejb: fix up compile failure]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC Discovery changes
- Treat received PLOGI while logged in as a relogin (unregister and reregister).
- Added a timer to delay Nport discovery when clean bit is cleared and Fabric
portname/nodename/FCID is changed.
- Invalidate Port's DID when receiving PLOGI from p2p port with CONFIG_PORT
mailbox command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Critical Errors:
- Correctly handle non-zero return lpfc_workq_post_event and return ENOMEM
- Save the irq level when locking the host_lock in lpfc_findnode_did
Bug Fixes:
- Adjust payload_length and request_length for sli4_config mailbox commands.
- Add the freed sgl/XRI to the tail of the list rather than to the head.
- Set the FC_VPORT_NEEDS_INIT_VPI on vport deletes and check it before
issuing a fdisc on an els retry.
- Only call lpfc_hba_init_link() if phba->cfg_suppress_link_up
is LPFC_INITIALIZE_LINK.
- Add support for SLI-4 Performance Hints
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support for ELS RRQ command
- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add SLI4 FC Discovery support
- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
is running as SLI-4 FC or FCoE port. Make sure flag reset each time
READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added driver logic to detect the last devloss timeout of remote nodes which
was still in use of FCF. At that point, the driver should set the last
in-use remote node devloss timeout flag if it was not already set and should
perform proper action on the in-use FCF and recover of FCF from firmware,
depending on the state the driver's FIP engine is in.
Find eligible FCF through FCF table rescan or the next new FCF event when
FCF table rescan turned out empty eligible FCF, and the successful flogi
into an FCF shall clear the HBA_DEVLOSS_TMO flag, indicating the successful
recovery from devloss timeout.
[jejb: add delay.h include to lpfc_hbadisc.c to fix ppc compile]
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support of received ELS commands
- Add support for received RLS ELS command
- Add support for received ECHO ELS command
- Add support for received RTV ELS command
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Remove unneeded Endian swap for Block Guard IOCB response
- Add a check for mailbox active before issuing the heartbeat command
- Correct heartbeat last_completion updates to avoid unneeded heartbeats
- Add Security crypto support to CONFIG_PORT mailbox command
- Add fips level and fips spec revision sysfs parameters
- Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox
- Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy
- Change log message 0318 from an error to a warning as it is not an error
- Patch an incorrect call to lpfc_drain_txq on SLI-3 functions
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add poll or wait flag parameter to hba_init_link and hba_down_link.
- (From Linux Community) Make return with ENXIO negative.
- Remove unused INB code from driver.
- Prevent block_magmt_io from returning until mailbox is inactive.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Enable NPIV by default.
- Added code to handle unsolicited LOGO on physical port.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add BSG support for PCI loopback testing.
- Add BSG support for extended mailbox commands.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Convert all sysfs parameters to uint instead of int.
- Add lpfc_supress_link_up parameter.
- Change link_state to writable sysfs parameter.
- Add support to be able to "up" or "down" link from link_state parameter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update BSG infrastructure to handle new vendor specific BSG commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FC protocol fixes.
- Fix send sequence logic to handle multi SGL IOCBs.
- Fix FDISC completion always setting VPORT state to failed.
- Ported the fix on reporting of max_vpi to uppper layer.
- Fix incorrect number of Vports allowed to be created.
- Fixed Dead FCoE port after creating vports.
- Added handling of ELS request for Reinstate Recovery Qualifier (RRQ)
- Handle unsolicited CT exchange initiator receiving CT exchange ABTS
- Migrate LUN queue depth ramp up code to scsi mid-layer.
- Made ABTS WQE go to the same WQ as the WQE to be aborted.
- Fix Vport does not rediscover after FCF goes away.
- Fixed lpfc_unreg_vfi failure after devloss timeout.
- Fixed RPI bit leak.
- Fix hbq pointer corruption during target discovery.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCoE Protocol fixes.
- Fixed FIP frame designation for ELS commands.
- Fix CVL received on Port 1 not processed by driver.
- Fix Zeroed frame on wire after FLOGI
- Fix vport keep-alive does not contain the correct WWN.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following changes:
- Fixed Panic/Hang when using polling mode for fcp commands
- Added support for Read_rev mbox bits indicating FIP mode of HBA
- Optimize performance of slow-path handling of els responses
- Add code to cleanup orphaned unsolicited receive sequences
- Fixed Devloss timeout when multiple initiators are in same zone
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch includes the following fixes:
- Fixed panic during HBA reset.
- Fixed FCoE event tag passed in resume_rpi.
- Fix out of order ELS commands
- Fixed discovery issues found during VLAN testing.
- Fix UNREG_VPI failure on extended link pull
- Fixed crash while processing unsolicited FC frames.
- Clear retry count in the delayed ELS handler
- Fixed discovery failure during quick link bounce.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add bsg (SGIOv4) support for sending and receiving ELS, CT commands
This patch adds a new file, lpfc_bsg.c.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a pair of FCoE issues
- Fix Region 23 FCoE Parameters not being read correctly
- Fix race condition when there are FCoE events during FCF table read
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Consistently implement persistent port disable.
Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Various SLI4 fixes
- Fix switch name not used in the FCF record for FCoE HBAs
- Enabled HBA UE error polling error-condition action code
- Rewrite lpfc_sli4_scmd_to_wqidx_distr() to handle counter rollover cleanly
- Modify resume_rpi mailbox data structure to match current SLI4 spec
- Do not issue mailbox command in MBX_POLL mode when LPFC_HBA_ERROR is set
- Wait for HBA POST completion before checking Online and UE registers
- Fix accumulated total length not being filled in on unsolicited IOCBs
- Use PCI config space register to determine SLI rev of HBA
- Turn on starting ELS tmo function timer during device initialization
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Contains the following changes
- Set the CT field of FDISC to 3
- Fixed over allocation of SCSI buffers on SLI4
- Removed unused jump table entries
- Increase LPFC_WQE_DEF_COUNT to 256
- Updated FDISC context to VPI
- Fixed immediate SCSI command for LUN reset translation to WQE
- Extended mailbox handling to allow MBX_POLL commands in between async
MBQ commands
- Fixed SID used for FDISC
- Fix crash when accessing ctlregs from sysfs for SLI4 HBAs
- Fix SLI4 firmware version not being saved or displayed correctly
- Expand CQID field in WQE structure to 16 bits
- Fix post header template mailbox command timing out
- Removed FCoE PCI device ID 0x0705
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update of copyrights on modified files
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds new hardware and interface definitions.
Adds new interface routines - utilizing the reorganized layout of the
driver. Adds SLI-4 specific functions for attachment, initialization,
teardown, etc.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Preps the organization of the driver so that the bottom half, which
interacts with the hardware, can share common code sequences for
attachment, detachment, initialization, teardown, etc with new hardware.
For very common code sections, which become specific to the interface
type, the driver uses an indirect function call. The function is set at
initialization. For less common sections, such as initialization, the
driver looks at the interface type and calls the routines relative to
the interface.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
8.3.1 Fixes/Changes :
- Fix incorrect byte-swapping on word 4 of IOCB (data length) which
caused LUNs to not be discovered on big-endian (e.g. PPC)
- Remove a bad cast of MBslimaddr which loses the __iomem (sparse)
- Make lpfc_debugfs_mask_disc_trc static (sparse)
- Correct misspelled word BlockGuard in lpfc_logmsg.h comment
- Replaced repeated code segment for canceling IOCBs from a list with
a function call, lpfc_sli_cancel_iocbs().
- Increased HBQ buffers to support 40KB SSC sequences.
- Added sysfs interface to update speed and topology parameter without
link bounce.
- Fixed bug with sysfs fc_host WWNs not being updated after changing
the WWNs.
- Check if the active mailbox is NULL in the beginning of the mailbox
timeout handler - fixes panic in the mailbox timeout handler while
running IO stress test
- Fixed system panic in lpfc_pci_remove_one() due to ndlp indirect
reference to phba through vport
- Removed de-reference of scsi device after call to scsi_done() to fix
panic in scsi completion path while accessing scsi device after
scsi_done is called.
- Fixed "Nodelist not empty" message when unloading the driver after
target reboot test
- Added LP2105 HBA model description
- Added code to print all 16 words of unrecognized ASYNC events
- Fixed memory leak in vport create + delete loop
- Added support for handling dual error bit from HBA
- Fixed a driver NULL pointer dereference in lpfc_sli_process_sol_iocb
- Fixed a discovery bug with FC switch reboot in lpfc_setup_disc_node
- Take NULL termintator into account when calculating available buffer space
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Update struct definitions, #defines, sysfs entries, and initialization
to support BlockGuard.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Per the recent discussions at the Linux Plumbers Conference, when
enabling MSI or MSI-X, generate a test interrupt to verify the
interrupt routing is working properly. If the test interrupt fails,
fall back to MSI first, and if that fails as well, to INTx. If the
interrupt test fails with INTx, log an error and fail the PCI probe.
Also changed the use of spin_(lock|unlock) to the _irq(save|restore)
variants in the interrupt handlers because with multi-message MSI-X,
both interrupt handlers can now run in parallel.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Fix lock up on rmmod with vports defined by having
lpfc_pci_remove_one() invoke fc_vport_terminate() to remove all the
vports before invoking fc_remove_host() for the physical port
- Fix echotest failure when NPIV is enabled
- Add the vport_disable function to the physical port's transport
template to make the vport disable attribute visible
- Set the vport state to DISABLE on create if the disable flag is
true
- Call lpfc_alloc_sysfs_attr() for vports so that statistical data
collection works on them
- Support setting a vport's symbolic name via sysfs by writing to
/sys/class/fc_vport/vportX/symbolic_name
- Fix create vport fails when link is down or in loop mode. Should be
able to be create vports any time NPIV is enabled
- Fix slow vport deletes when deleting multiple vports at once
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for new sysfs attributes: lpfc_stat_data_ctrl and
lpfc_max_scsicmpl_time. The attributes control statistical reporting
of io load.
Added support for new fc vendor events for error reporting.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added new sysfs attribute lpfc_max_scsicmpl_time. Attribute, when enabled,
will control target queue depth based on I/O completion time.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>