Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all genl families ethtool_genl_family needs to not
be a straight up constant, because it's modified/initialized
by genl_register_family(). After init, however, it's only
passed to genlmsg_put() & co. therefore we can mark it
as __ro_after_init.
Since genl_family structure contains function pointers
mark this as a fix.
Fixes: 2b4a8990b7 ("ethtool: introduce ethtool netlink interface")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.
As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.
Fixes: c7d759eb7b ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers have to report their pause frames statistics
via ethtool -S, and there is a wide variety of names used for
these statistics.
Add the two statistics defined in IEEE 802.3x to the standard
API. Create a new ethtool request header flag for including
statistics in the response to GET commands.
Always create the ETHTOOL_A_PAUSE_STATS nest in replies when
flag is set. Testing if driver declares the op is not a reliable
way of checking if any stats will actually be included and therefore
we don't want to give the impression that presence of
ETHTOOL_A_PAUSE_STATS indicates driver support.
Note that this patch does not include PFC counters, which may fit
better in dcbnl? But mostly I don't need them/have a setup to test
them so I haven't looked deeply into exposing them :)
v3:
- add a helper for "uninitializing" stats, rather than a cryptic
memset() (Andrew)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ops->set_phys_id() returned an error, previously we would only break
out of the inner loop, which neither stopped the outer loop nor returned
the error to the user (since 'rc' would be overwritten on the next pass
through the loop).
Thus, rewrite it to use a single loop, so that the break does the right
thing. Use u64 for 'count' and 'i' to prevent overflow in case of
(unreasonably) large values of id.data and n.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-09-01
The following pull-request contains BPF updates for your *net-next* tree.
There are two small conflicts when pulling, resolve as follows:
1) Merge conflict in tools/lib/bpf/libbpf.c between 88a8212028 ("libbpf: Factor
out common ELF operations and improve logging") in bpf-next and 1e891e513e
("libbpf: Fix map index used in error message") in net-next. Resolve by taking
the hunk in bpf-next:
[...]
scn = elf_sec_by_idx(obj, obj->efile.btf_maps_shndx);
data = elf_sec_data(obj, scn);
if (!scn || !data) {
pr_warn("elf: failed to get %s map definitions for %s\n",
MAPS_ELF_SEC, obj->path);
return -EINVAL;
}
[...]
2) Merge conflict in drivers/net/ethernet/mellanox/mlx5/core/en/xsk/rx.c between
9647c57b11 ("xsk: i40e: ice: ixgbe: mlx5: Test for dma_need_sync earlier for
better performance") in bpf-next and e20f0dbf20 ("net/mlx5e: RX, Add a prefetch
command for small L1_CACHE_BYTES") in net-next. Resolve the two locations by retaining
net_prefetch() and taking xsk_buff_dma_sync_for_cpu() from bpf-next. Should look like:
[...]
xdp_set_data_meta_invalid(xdp);
xsk_buff_dma_sync_for_cpu(xdp, rq->xsk_pool);
net_prefetch(xdp->data);
[...]
We've added 133 non-merge commits during the last 14 day(s) which contain
a total of 246 files changed, 13832 insertions(+), 3105 deletions(-).
The main changes are:
1) Initial support for sleepable BPF programs along with bpf_copy_from_user() helper
for tracing to reliably access user memory, from Alexei Starovoitov.
2) Add BPF infra for writing and parsing TCP header options, from Martin KaFai Lau.
3) bpf_d_path() helper for returning full path for given 'struct path', from Jiri Olsa.
4) AF_XDP support for shared umems between devices and queues, from Magnus Karlsson.
5) Initial prep work for full BPF-to-BPF call support in libbpf, from Andrii Nakryiko.
6) Generalize bpf_sk_storage map & add local storage for inodes, from KP Singh.
7) Implement sockmap/hash updates from BPF context, from Lorenz Bauer.
8) BPF xor verification for scalar types & add BPF link iterator, from Yonghong Song.
9) Use target's prog type for BPF_PROG_TYPE_EXT prog verification, from Udip Pant.
10) Rework BPF tracing samples to use libbpf loader, from Daniel T. Lee.
11) Fix xdpsock sample to really cycle through all buffers, from Weqaar Janjua.
12) Improve type safety for tun/veth XDP frame handling, from Maciej Żenczykowski.
13) Various smaller cleanups and improvements all over the place.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the AF_XDP zero-copy driver interface functions to better
reflect what they do after the replacement of umems with buffer
pools in the previous commit. Mostly it is about replacing the
umem name from the function names with xsk_buff and also have
them take the a buffer pool pointer instead of a umem. The
various ring functions have also been renamed in the process so
that they have the same naming convention as the internal
functions in xsk_queue.h. This so that it will be clearer what
they do and also for consistency.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-3-git-send-email-magnus.karlsson@intel.com
Replace the explicit umem reference passed to the driver in AF_XDP
zero-copy mode with the buffer pool instead. This in preparation for
extending the functionality of the zero-copy mode so that umems can be
shared between queues on the same netdev and also between netdevs. In
this commit, only an umem reference has been added to the buffer pool
struct. But later commits will add other entities to it. These are
going to be entities that are different between different queue ids
and netdevs even though the umem is shared between them.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/1598603189-32145-2-git-send-email-magnus.karlsson@intel.com
Set IP protocol mask only when IP protocol field is set.
This will allow flow-type ether with vlan rule which don't have
protocol field to apply.
ethtool -N ens5f4 flow-type ether proto 0x8100 vlan 0x600\
m 0x1FFF action 3 loc 16
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy ethtool userspace tool shows an error when no features could
be changed. It's useful to have a netlink reply to be able to show this
error when __netdev_update_features wasn't called, for example:
1. ethtool -k eth0
large-receive-offload: off
2. ethtool -K eth0 rx-fcs on
3. ethtool -K eth0 lro on
Could not change any device features
rx-lro: off [requested on]
4. ethtool -K eth0 lro on
# The output should be the same, but without this patch the kernel
# doesn't send the reply, and ethtool is unable to detect the error.
This commit makes ethtool-netlink always return a reply when requested,
and it still avoids unnecessary calls to __netdev_update_features if the
wanted features haven't changed.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool-netlink ignores dev->hw_features and may confuse the drivers by
asking them to enable features not in the hw_features bitmask. For
example:
1. ethtool -k eth0
tls-hw-tx-offload: off [fixed]
2. ethtool -K eth0 tls-hw-tx-offload on
tls-hw-tx-offload: on
3. ethtool -k eth0
tls-hw-tx-offload: on [fixed]
Fitler out dev->hw_features from req_wanted to fix it and to resemble
the legacy ethtool behavior.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool-netlink calculates new wanted bits as:
(req_wanted & req_mask) | (old_active & ~req_mask)
It completely discards the old wanted bits, so they are forgotten with
the next ethtool command. Sample steps to reproduce:
1. ethtool -k eth0
tx-tcp-segmentation: on # TSO is on from the beginning
2. ethtool -K eth0 tx off
tx-tcp-segmentation: off [not requested]
3. ethtool -k eth0
tx-tcp-segmentation: off [requested on]
4. ethtool -K eth0 rx off # Some change unrelated to TSO
5. ethtool -k eth0
tx-tcp-segmentation: off # "Wanted on" is forgotten
This commit fixes it by changing the formula to:
(req_wanted & req_mask) | (old_wanted & ~req_mask),
where old_active was replaced by old_wanted to account for the wanted
bits.
The shortcut condition for the case where nothing was changed now
compares wanted bitmasks, instead of wanted to active.
Fixes: 0980bfcd69 ("ethtool: set netdev features with FEATURES_SET request")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl8oRdgACgkQSD+KveBX
+j4/LQgAkSjNzOaS7bVDzhoYL3aBQOMIzgocJUeVi7xXH8IO1uy55mNDrKBqjxbW
dy9U9VsvV5i2V2qkkQLvHVkoDSg8Buo2Uxu4OrZHOLN0KfbFrra4VvmB1CzEBix8
FICnQaZZcE7529P04TgZ8Mo9vRb5VdJFhqED5Nvegy+y8FolEsQYbjIoDBE6wa0j
Meqa/29+XCE5FzTOjbbQWizAnRZMbkxtSSreDNgeHxke9eMSO+fmwKScng63QUfl
7nfU6dW6A0d1kHhpL5RqAFOcmkpSdqYaA3SA+/8pPT9X3yOAkxE6KTKGIixpB9JX
zQt+Wkna49jJ/JfDQB5vgww5c0HjAQ==
=j0fG
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 has the IANA VXLAN port (4789) hard coded by the device,
instead of being added dynamically when tunnels are created.
To support this add a workaround flag to struct udp_tunnel_nic_info.
Skipping updates for the port is fairly trivial, dumping the hard
coded port via ethtool requires some code duplication. The port
is not a part of any real table, we dump it in a special table
which has no tunnel types supported and only one entry.
This is the last known workaround / hack needed to convert
all drivers to the new infra.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have moved the PHY ethtool statistics to be dynamically
registered, we no longer need to inline those for ethtool. This used to
be done to avoid cross symbol referencing and allow ethtool to be
decoupled from PHYLIB entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have introduced ethtool_phy_ops and the PHY library
dynamically registers its operations with that function pointer, we can
remove the direct PHYLIB dependency in favor of using dynamic
operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to decouple ethtool from its PHY library dependency, define an
ethtool_phy_ops singleton which can be overriden by the PHY library when
it loads with an appropriate set of function pointers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting SQI or maximum SQI value fails in linkstate_prepare_data(), we
must not return without calling ethnl_ops_complete(dev) as that could
result in imbalance between ethtool_ops ->begin() and ->complete() calls.
Fixes: 8066021915 ("ethtool: provide UAPI for PHY Signal Quality Index (SQI)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A last minute change put the TDR cable test parameters into a nest.
The validation is not sufficient, resulting in an oops if the nest is
missing. Set default values first, then update them if the nest is
provided.
Fixes: f2bc8ad31a ("net: ethtool: Allow PHY cable test TDR data to configured")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e585f23636 ("udp: Changes to udp_offload to support remote
checksum offload") added new GSO type and a corresponding netdev
feature, but missed Ethtool's 'netdev_features_strings' table.
Give it a name so it will be exposed to userspace and become available
for manual configuration.
v3:
- decouple from "netdev_features_strings[] cleanup" series;
- no functional changes.
v2:
- don't split the "Fixes:" tag across lines;
- no functional changes.
Fixes: e585f23636 ("udp: Changes to udp_offload to support remote checksum offload")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b33583265 ("net: Add fraglist GRO/GSO feature flags") missed
an entry for NETIF_F_GSO_FRAGLIST in netdev_features_strings array. As
a result, fraglist GSO feature is not shown in 'ethtool -k' output and
can't be toggled on/off.
The fix is trivial.
Fixes: 3b33583265 ("net: Add fraglist GRO/GSO feature flags")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().
This issue was found with the help of Coccinelle and, audited and fixed
manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates a Smatch warning:
net/ethtool/linkinfo.c:143 ethnl_set_linkinfo()
warn: variable dereferenced before check 'info' (see line 119)
Fortunately, the "info" pointer is never NULL so the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot is reporting:
net/ethtool/cabletest.c:230:5: warning: no previous prototype for
Mark the function as static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't call drivers if nothing changed. Netlink code already
contains this logic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given that it takes time to run a cable test, send a notify message at
the start, as well as when it is completed.
v3:
EMSGSIZE when ethnl_bcastmsg_put() fails
Print an error message on failure, since this is a void function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PHY drivers can use these helpers for reporting the results. The
results get translated into netlink attributes which are added to the
pre-allocated skbuf.
v3:
Poison phydev->skb
Return -EMSGSIZE when ethnl_bcastmsg_put() fails
Return valid error code when nla_nest_start() fails
Use u8 for results
Actually put u32 length into message
v4:
s/ENOTSUPP/EOPNOTSUPP/g
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide infrastructure for PHY drivers to report the cable test
results. A netlink skb is associated to the phydev. Helpers will be
added which can add results to this skb. Once the test has finished
the results are sent to user space.
When netlink ethtool is not part of the kernel configuration stubs are
provided. It is also impossible to trigger a cable test, so the error
code returned by the alloc function is of no consequence.
v2:
Include the status complete in the netlink notification message
v4:
Replace -EINVAL with -EMSGSIZE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make some helpers for building ethtool netlink messages available
outside the compilation unit, so they can be used for building
messages which are not simple get/set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new ethtool netlink calls to trigger the starting of a PHY cable
test.
Add Kconfig'ury to ETHTOOL_NETLINK so that PHYLIB is not a module when
ETHTOOL_NETLINK is builtin, which would result in kernel linking errors.
v2:
Remove unwanted white space change
Remove ethnl_cable_test_act_ops and use doit handler
Rename cable_test_set_policy cable_test_act_policy
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY
v3:
Remove ETHTOOL_MSG_CABLE_TEST_ACT_REPLY from documentation
Remove unused cable_test_get_policy
Add Reviewed-by tags
v4:
Remove unwanted blank line
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is executing a self test, put the interface into
operative status testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool --set-priv-flags veth1 foo on
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
Fixes: f265d79959 ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduce a new netdev feature, which will be used by drivers
to state they can perform MACsec transformations in hardware.
The patchset was gathered by Mark, macsec functinality itself
was implemented by Dmitry, Mark and Pavel Belous.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.
The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).
Fixes: f70bb06563 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all in-tree drivers have been updated we can
make the supported_coalesce_params mandatory.
To save debugging time in case some driver was missed
(or is out of tree) add a warning when netdev is registered
with set_coalesce but without supported_coalesce_params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jakub Kicinski, we ethtool netlink code should respond
with an error if request head has flags set which are not recognized by
kernel, either as a mistake or because it expects functionality introduced
in later kernel versions.
To avoid unnecessary roundtrips, use extack cookie to provide the
information about supported request flags.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of spelling mistakes in NL_SET_ERR_MSG_ATTR messages.
Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_CHANNELS_NTF notification whenever channel counts of
a network device are modified using ETHTOOL_MSG_CHANNELS_SET netlink
message or ETHTOOL_SCHANNELS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_SET netlink request to set channel counts of a network
device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack. Checks preventing removing channels
used for RX indirection table or zerocopy AF_XDP socket are also
implemented.
Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be
used by both ioctl and netlink code.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement CHANNELS_GET request to get channel counts of a network device.
These are traditionally available via ETHTOOL_GCHANNELS ioctl request.
Omit attributes for channel types which are not supported by driver or
device (zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in channels_prepare_data()
- more descriptive channels_reply_size()
- omit attributes with zero max count
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_RINGS_NTF notification whenever ring sizes of a network
device are modified using ETHTOOL_MSG_RINGS_SET netlink message or
ETHTOOL_SRINGPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement RINGS_SET netlink request to set ring sizes of a network device.
These are traditionally set with ETHTOOL_SRINGPARAM ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement RINGS_GET request to get ring sizes of a network device. These
are traditionally available via ETHTOOL_GRINGPARAM ioctl request.
Omit attributes for ring types which are not supported by driver or device
(zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in rings_prepare_data()
- more descriptive rings_reply_size()
- omit attributes with zero max size
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_PRIVFLAGS_NTF notification whenever private flags of
a network device are modified using ETHTOOL_MSG_PRIVFLAGS_SET netlink
message or ETHTOOL_SPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PRIVFLAGS_SET netlink request to set private flags of a network
device. These are traditionally set with ETHTOOL_SPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement PRIVFLAGS_GET request to get private flags for a network device.
These are traditionally available via ETHTOOL_GPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_FEATURES_NTF notification whenever network device features
are modified using ETHTOOL_MSG_FEATURES_SET netlink message, ethtool ioctl
request or any other way resulting in call to netdev_update_features() or
netdev_change_features()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement FEATURES_SET netlink request to set network device features.
These are traditionally set using ETHTOOL_SFEATURES ioctl request.
Actual change is subject to netdev_change_features() sanity checks so that
it can differ from what was requested. Unlike with most other SET requests,
in addition to error code and optional extack, kernel provides an optional
reply message (ETHTOOL_MSG_FEATURES_SET_REPLY) in the same format but with
different semantics: information about difference between user request and
actual result and difference between old and new state of dev->features.
This reply message can be suppressed by setting ETHTOOL_FLAG_OMIT_REPLY
flag in request header.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other SET type commands, modifying netdev features is required to
provide a reply telling userspace what was actually changed, compared to
what was requested. For that purpose, the "modified" flag provided by
ethnl_update_bitset() is not sufficient, we need full information which
bits were requested to change.
Therefore provide ethnl_parse_bitset() returning effective value and mask
bitmaps equivalent to the contents of a bitset nested attribute.
v2: use non-atomic __set_bit() (suggested by David Miller)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement FEATURES_GET request to get network device features. These are
traditionally available via ETHTOOL_GFEATURES ioctl request.
v2:
- style cleanup suggested by Jakub Kicinski
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Legacy ioctl request like ETHTOOL_GTXCSUM are still used by ethtool utility
to get values of legacy flags (which rather work as feature groups). These
are calculated from values of actual features and request to set them is
implemented as an attempt to set all features mapping to them but there are
two inconsistencies:
- tx-checksum-fcoe-crc is shown under tx-checksumming but NETIF_F_FCOE_CRC
is not included in ETHTOOL_GTXCSUM/ETHTOOL_STXCSUM
- tx-scatter-gather-fraglist is shown under scatter-gather but
NETIF_F_FRAGLIST is not included in ETHTOOL_GSG/ETHTOOL_SSG
As the mapping in ethtool output is more correct from logical point of
view, fix ethtool_get_feature_mask() to match it.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn pointed out that even if it's documented that
ethnl_parse_header() takes reference to network device if it fills it
into the target structure, its name doesn't make it apparent so that
corresponding dev_put() looks like mismatched.
Rename the function ethnl_parse_header_dev_get() to indicate that it
takes a reference.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.
To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.
This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.
The same mask is used for global and per queue settings.
v3: - move the (temporary) check if driver defines types
earlier (Michal)
- rename used_types -> nonzero_params, and
coalesce_types -> supported_coalesce_params (Alex)
- use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported that ethnl_compact_sanity_checks() can be tricked into
reading past the end of ETHTOOL_A_BITSET_VALUE and ETHTOOL_A_BITSET_MASK
attributes and even the message by passing a value between (u32)(-31)
and (u32)(-1) as ETHTOOL_A_BITSET_SIZE.
The problem is that DIV_ROUND_UP(attr_nbits, 32) is 0 for such values so
that zero length ETHTOOL_A_BITSET_VALUE will pass the length check but
ethnl_bitmap32_not_zero() check would try to access up to 512 MB of
attribute "payload".
Prevent this overflow byt limiting the bitset size. Technically, compact
bitset format would allow bitset sizes up to almost 2^18 (so that the
nest size does not exceed U16_MAX) but bitsets used by ethtool are much
shorter. S16_MAX, the largest value which can be directly used as an
upper limit in policy, should be a reasonable compromise.
Fixes: 10b518d4e6 ("ethtool: netlink bitset handling")
Reported-by: syzbot+7fd4ed5b4234ab1fdccd@syzkaller.appspotmail.com
Reported-by: syzbot+709b7a64d57978247e44@syzkaller.appspotmail.com
Reported-by: syzbot+983cb8fb2d17a7af549d@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for low latency Reed Solomon FEC as LLRS.
The LL-FEC is defined by the 25G/50G ethernet consortium,
in the document titled "Low Latency Reed Solomon Forward Error Correction"
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
A bitset without mask in a _SET request means we want exactly the bits in
the bitset to be set. This works correctly for compact format but when
verbose format is parsed, ethnl_update_bitset32_verbose() only sets the
bits present in the request bitset but does not clear the rest. This can
cause incorrect results like
lion:~ # ethtool eth0 | grep Wake
Supports Wake-on: pumbg
Wake-on: g
lion:~ # ethtool -s eth0 wol u
lion:~ # ethtool eth0 | grep Wake
Supports Wake-on: pumbg
Wake-on: ug
when the second ethtool command issues request
ETHTOOL_MSG_WOL_SET
ETHTOOL_A_WOL_HEADER
ETHTOOL_A_HEADER_DEV_NAME = "eth0"
ETHTOOL_A_WOL_MODES
ETHTOOL_A_BITSET_NOMASK
ETHTOOL_A_BITSET_BITS
ETHTOOL_A_BITSET_BITS_BIT
ETHTOOL_BITSET_BIT_INDEX = 1
Fix the logic by clearing the whole target bitmap before we start iterating
through the request bits.
Fixes: 10b518d4e6 ("ethtool: netlink bitset handling")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to stop useless driver version bumps and unify output
presented by ethtool -i, let's set default version string.
As Linus said in [1]: "Things are supposed to be backwards and
forwards compatible, because we don't accept breakage in user
space anyway. So versioning is pointless, and only causes
problems."
They cause problems when users start to see version changes
and expect specific set of features which will be different
for stable@, vanilla and distribution kernels.
Distribution kernels are based on some kernel version with extra
patches on top, for example, in RedHat world this "extra" is a lot
and for them your driver version say nothing. Users who run vanilla
kernels won't use driver version information too, because running
such kernels requires knowledge and understanding.
Another set of problems are related to difference in versioning scheme
and such doesn't allow to write meaningful automation which will work
sanely on all ethtool capable devices.
Before this change:
[leonro@erver ~]$ ethtool -i eth0
driver: virtio_net
version: 1.0.0
After this change and once ->version assignment will be deleted
from virtio_net:
[leonro@server ~]$ ethtool -i eth0
driver: virtio_net
version: 5.5.0-rc6+
Link: https://lore.kernel.org/ksummit-discuss/CA+55aFx9A=5cc0QZ7CySC4F2K7eYaEfzkdYEc9JaNgCcV25=rg@mail.gmail.com/
Link: https://lore.kernel.org/linux-rdma/20200122152627.14903-1-michal.kalderon@marvell.com/T/#md460ff8f976c532a89d6860411c3c50bb811038b
Link: https://lore.kernel.org/linux-rdma/20200127060835.GA570@unicorn.suse.cz
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_WOL_NTF notification whenever wake-on-lan settings of
a device are modified using ETHTOOL_MSG_WOL_SET netlink message or
ETHTOOL_SWOL ioctl request.
As notifications can be received by anyone, do not include SecureOn(tm)
password in notification messages.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_SET netlink request to set wake-on-lan settings. This is
equivalent to ETHTOOL_SWOL ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement WOL_GET request to get wake-on-lan settings for a device,
traditionally available via ETHTOOL_GWOL ioctl request.
As part of the implementation, provide symbolic names for wake-on-line
modes as ETH_SS_WOL_MODES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_DEBUG_NTF notification message whenever debugging message
mask for a device are modified using ETHTOOL_MSG_DEBUG_SET netlink message
or ETHTOOL_SMSGLVL ioctl request.
The notification message has the same format as reply to DEBUG_GET request.
As with other ethtool notifications, netlink requests only trigger the
notification if the mask is actually changed while ioctl request trigger it
whenever the request results in calling the ethtool_ops handler.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_SET netlink request to set debugging settings for a device.
At the moment, only message mask corresponding to message level as set by
ETHTOOL_SMSGLVL ioctl request can be set. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_GET request to get debugging settings for a device. At the
moment, only message mask corresponding to message level as reported by
ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
As part of the implementation, provide symbolic names for message mask bits
as ETH_SS_MSG_CLASSES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing or incorrect function argument and struct member descriptions.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds new Fraglist GRO/GSO feature flags. They will be used
to configure fraglist GRO/GSO what will be implemented with some
followup paches.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch complains that the NULL checking isn't done consistently:
net/ethtool/strset.c:253 strset_prepare_data()
error: we previously assumed 'dev' could be null (see line 233)
It looks like there is a missing return on this path.
Fixes: 71921690f9 ("ethtool: provide string sets with STRSET_GET request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ret < 0" comparison is never true because "ret" is still zero.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ethnl_default_parse() fails then we need to free a couple
memory allocations before returning.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/ethtool/linkmodes.c: In function 'ethnl_set_linkmodes':
net/ethtool/linkmodes.c:326:32: warning:
variable 'lsettings' set but not used [-Wunused-but-set-variable]
struct ethtool_link_settings *lsettings;
^
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKSTATE_GET netlink request to get link state information.
At the moment, only link up flag as provided by ETHTOOL_GLINK ioctl command
is returned.
LINKSTATE_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_LINKMODES_NTF notification message whenever device link
settings or advertised modes are modified using ETHTOOL_MSG_LINKMODES_SET
netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.
The notification message has the same format as reply to LINKMODES_GET
request. ETHTOOL_MSG_LINKMODES_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.
As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKMODES_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKMODES_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKMODES_SET netlink request to set advertised linkmodes and
related attributes as ETHTOOL_SLINKSETTINGS and ETHTOOL_SSET commands do.
The request allows setting autonegotiation flag, speed, duplex and
advertised link modes.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKMODES_GET netlink request to get link modes related
information provided by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl
commands.
This request provides supported, advertised and peer advertised link modes,
autonegotiation flag, speed and duplex.
LINKMODES_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send ETHTOOL_MSG_LINKINFO_NTF notification message whenever device link
settings are modified using ETHTOOL_MSG_LINKINFO_SET netlink message or
ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands.
The notification message has the same format as reply to LINKINFO_GET
request. ETHTOOL_MSG_LINKINFO_SET netlink request only triggers the
notification if there is a change but the ioctl command handlers do not
check if there is an actual change and trigger the notification whenever
the commands are executed.
As all work is done by ethnl_default_notify() handler and callback
functions introduced to handle LINKINFO_GET requests, all that remains is
adding entries for ETHTOOL_MSG_LINKINFO_NTF into ethnl_notify_handlers and
ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where
needed.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool netlink notifications have the same format as related GET
replies so that if generic GET handling framework is used to process GET
requests, its callbacks and instance of struct get_request_ops can be
also used to compose corresponding notification message.
Provide function ethnl_std_notify() to be used as notification handler in
ethnl_notify_handlers table.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKINFO_SET netlink request to set link settings queried by
LINKINFO_GET message.
Only physical port, phy MDIO address and MDI(-X) control can be set,
attempt to modify MDI(-X) status and transceiver is rejected.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement LINKINFO_GET netlink request to get basic link settings provided
by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl commands.
This request provides settings not directly related to autonegotiation and
link mode selection: physical port, phy MDIO address, MDI(-X) status,
MDI(-X) control and transceiver.
LINKINFO_GET request can be used with NLM_F_DUMP (without device
identification) to request the information for all devices in current
network namespace providing the data.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Requests a contents of one or more string sets, i.e. indexed arrays of
strings; this information is provided by ETHTOOL_GSSET_INFO and
ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all
information can be retrieved with one request and mulitple string sets can
be requested at once.
There are three types of requests:
- no NLM_F_DUMP, no device: get "global" stringsets
- no NLM_F_DUMP, with device: get string sets related to the device
- NLM_F_DUMP, no device: get device related string sets for all devices
Client can request either all string sets of given type (global or device
related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only
set sizes (numbers of strings) are returned.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Significant part of GET request processing is common for most request
types but unfortunately it cannot be easily separated from type specific
code as we need to alternate between common actions (parsing common request
header, allocating message and filling netlink/genetlink headers etc.) and
specific actions (querying the device, composing the reply). The processing
also happens in three different situations: "do" request, "dump" request
and notification, each doing things in slightly different way.
The request specific code is implemented in four or five callbacks defined
in an instance of struct get_request_ops:
parse_request() - parse incoming message
prepare_data() - retrieve data from driver or NIC
reply_size() - estimate reply message size
fill_reply() - compose reply message
cleanup_data() - (optional) clean up additional data
Other members of struct get_request_ops describe the data structure holding
information from client request and data used to compose the message. The
default handlers ethnl_default_doit(), ethnl_default_dumpit(),
ethnl_default_start() and ethnl_default_done() can be then used in genl_ops
handler. Notification handler will be introduced in a later patch.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for ethtool netlink notifications. There is only one
multicast group "monitor" which is used to notify userspace about changes
and actions performed. Notification messages (types using suffix _NTF)
share the format with replies to GET requests.
Notifications are supposed to be broadcasted on every configuration change,
whether it is done using the netlink interface or ioctl one. Netlink SET
requests only trigger a notification if some data is actually changed.
To trigger an ethtool notification, both ethtool netlink and external code
use ethtool_notify() helper. This helper requires RTNL to be held and may
sleep. Handlers sending messages for specific notification message types
are registered in ethnl_notify_handlers array. As notifications can be
triggered from other code, ethnl_ok flag is used to prevent an attempt to
send notification before genetlink family is registered.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool netlink code uses common framework for passing arbitrary
length bit sets to allow future extensions. A bitset can be a list (only
one bitmap) or can consist of value and mask pair (used e.g. when client
want to modify only some bits). A bitset can use one of two formats:
verbose (bit by bit) or compact.
Verbose format consists of bitset size (number of bits), list flag and
an array of bit nests, telling which bits are part of the list or which
bits are in the mask and which of them are to be set. In requests, bits
can be identified by index (position) or by name. In replies, kernel
provides both index and name. Verbose format is suitable for "one shot"
applications like standard ethtool command as it avoids the need to
either keep bit names (e.g. link modes) in sync with kernel or having to
add an extra roundtrip for string set request (e.g. for private flags).
Compact format uses one (list) or two (value/mask) arrays of 32-bit
words to store the bitmap(s). It is more suitable for long running
applications (ethtool in monitor mode or network management daemons)
which can retrieve the names once and then pass only compact bitmaps to
save space.
Userspace requests can use either format; ETHTOOL_FLAG_COMPACT_BITSETS
flag in request header tells kernel which format to use in reply.
Notifications always use compact format.
As some code uses arrays of unsigned long for internal representation and
some arrays of u32 (or even a single u32), two sets of parse/compose
helpers are introduced. To avoid code duplication, helpers for unsigned
long arrays are implemented as wrappers around helpers for u32 arrays.
There are two reasons for this choice: (1) u32 arrays are more frequent in
ethtool code and (2) unsigned long array can be always interpreted as an
u32 array on little endian 64-bit and all 32-bit architectures while we
would need special handling for odd number of u32 words in the opposite
direction.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common request/reply header definition and helpers to parse request
header and fill reply header. Provide ethnl_update_* helpers to update
structure members from request attributes (to be used for *_SET requests).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic genetlink and init infrastructure for the netlink interface, register
genetlink family "ethtool". Add CONFIG_ETHTOOL_NETLINK Kconfig option to
make the build optional. Add initial overall interface description into
Documentation/networking/ethtool-netlink.rst, further patches will add more
detailed information.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike e.g. netdev features, the ethtool ioctl interface requires link mode
table to be in sync between kernel and userspace for userspace to be able
to display and set all link modes supported by kernel. The way arbitrary
length bitsets are implemented in netlink interface, this will be no longer
needed.
To allow userspace to access all link modes running kernel supports, add
table of ethernet link mode names and make it available as a string set to
userspace GET_STRSET requests. Add build time check to make sure names
are defined for all modes declared in enum ethtool_link_mode_bit_indices.
Once the string set is available, make it also accessible via ioctl.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce file net/ethtool/common.c for code shared by ioctl and netlink
ethtool interface. Move name tables of features, RSS hash functions,
tunables and PHY tunables into this file.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool netlink interface is going to be split into multiple files so
that it will be more convenient to put all of them in a separate directory
net/ethtool. Start by moving current ethtool.c with ioctl interface into
this directory and renaming it to ioctl.c.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller