{ Update to correct 1 patch subject in the description }
We have fixed a lot of race issues in the EC driver recently.
The following commit introduces MSI udelay()/msleep() quirk to MSI laptops
to make EC firmware working for bug 12011 without root causing any EC
driver race issues:
Commit: 5423a0cb3f
Subject: ACPI: EC: Add delay for slow MSI controller
Commit: 34ff4dbccc
Subject: ACPI: EC: Separate delays for MSI hardware
The following commit extends ECDT validation quirk to MSI laptops to make
EC driver locating EC registers properly for bug 12461:
Commit: a5032bfdd9
Subject: ACPI: EC: Always parse EC device
This is a different quirk than the MSI udelay()/msleep() quirk. This patch
keeps validating ECDT for only "Micro-Star MS-171F" as reported.
The following commit extends MSI udelay()/msleep() quirk to Quanta laptops
to make EC firmware working for bug 20242, there is no requirement to
validate ECDT for Quanta laptops:
Commit: 534bc4e3d2 Mon Sep 17 00:00:00 2001
Subject: ACPI EC: enable MSI workaround for Quanta laptops
The following commit extends MSI udelay()/msleep() quirk to Clevo laptops
to make EC firmware working for bug 77431, there is no requirement to
validate ECDT for Clevo laptops:
Commit: 777cb38295
Subject: ACPI / EC: Add msi quirk for Clevo W350etq
All udelay()/msleep() quirks for MSI/Quanta/Clevo seem to be the wrong
fixes generated without fixing the EC driver race issues.
And even if it is not wrong, the guarding can be covered by the following
commits in wait polling mode:
Commit: 9e295ac14d
Subject: ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
Commit: commit in the same series
Subject: ACPI / EC: Fix and clean up register access guarding logics.
The only case that is not covered is the inter-transaction guarding. And
there is no evidence that we need the inter-transaction guarding upon
reading the noted bug entries.
So it is time to remove the quirks and let the users to try again. If there
is a regression, the only thing we need to do is to restore the
inter-transaction guarding for the reported platforms.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12461
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have 2 polling modes in the EC driver:
1. busy polling: originally used for the MSI quirks. udelay() is used to
perform register access guarding.
2. wait polling: normal code path uses wait_event_timeout() and it can be
woken up as soon as the transaction is completed in the interrupt mode.
It also contains the register acces guarding logic in case the interrupt
doesn't arrive and the EC driver is about to advance the transaction in
task context (the polling mode).
The wait polling is useful for interrupt mode to allow other tasks to use
the CPU during the wait.
But for the polling mode, the busy polling takes less time than the wait
polling, because if no interrupt arrives, the wait polling has to wait the
minimal HZ interval.
We have a new use case for using the busy polling mode. Some GPIO drivers
initialize PIN configuration which cause a GPIO multiplexed EC GPE to be
disabled out of the GPE register's control. Busy polling mode is useful
here as it takes less time than the wait polling. But the guarding logic
prevents it from responding even faster. We should spinning around the EC
status rather than spinning around the nop execution lasted a determined
period.
This patch introduces 2 module params for the polling mode switch and the
guard time, so that users can use the busy polling mode without the
guarding in case the guarding is not necessary. This is an example to use
the 2 module params for this purpose:
acpi.ec_busy_polling acpi.ec_polling_guard=0
We've tested the patch on a test platform. The platform suffers from such
kind of the GPIO PIN issue. The GPIO driver resets all PIN configuration
and after that, EC interrupt cannot arrive because of the multiplexing.
Then the platform suffers from a long delay carried out by the
wait_event_timeout() as all further EC transactions will run in the polling
mode. We switched the EC driver to use the busy polling mechanism instead
of the wait timeout polling mechanism and the delay is still high:
[ 44.283005] calling PNP0C0B:00+ @ 1305, parent: platform
[ 44.417548] call PNP0C0B:00+ returned 0 after 131323 usecs
And this patch can significantly reduce the delay:
[ 44.502625] calling PNP0C0B:00+ @ 1308, parent: platform
[ 44.503760] call PNP0C0B:00+ returned 0 after 1103 usecs
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the polling mode, EC driver shouldn't access the EC registers too
frequently. Though this statement is concluded from the non-root caused
bugs (see links below), we've maintained the register access guarding
logics in the current EC driver. The guarding logics can be found here and
there, makes it hard to root cause real timing issues. This patch collects
the guarding logics into one single function so that all hidden logics
related to this can be seen clearly.
The current guarding related code also has several issues:
1. Per-transaction timestamp prevents inter-transaction guarding from being
implemented in the same place. We have an inter-transaction udelay() in
acpi_ec_transaction_unblocked(), this logic can be merged into ec_poll()
if we can use per-device timestamp. This patch completes such merge to
form a new ec_guard() function and collects all guarding related hidden
logics in it.
One hidden logic is: there is no inter-transaction guarding performed
for non MSI quirk (wait polling mode), this patch skips
inter-transaction guarding before wait_event_timeout() for the wait
polling mode to reveal the hidden logic.
The other hidden logic is: there is msleep() inter-transaction guarding
performed when the GPE storming is observed. As after merging this
commit:
Commit: e1d4d90fc0
Subject: ACPI / EC: Refine command storm prevention support
EC_FLAGS_COMMAND_STORM is ensured to be cleared after invoking
acpi_ec_transaction_unlocked(), the msleep() guard logic will never
happen now. Since no one complains such change, this logic is likely
added during the old times where the EC race issues are not fixed and
the bugs are false root-caused to the timing issue. This patch simply
removes the out-dated logic. We can restore it by stop skipping
inter-transaction guarding for wait polling mode.
Two different delay values are defined for msleep() and udelay() while
they are merged in this patch to 550us.
2. time_after() causes additional delay in the polling mode (can only be
observed in noirq suspend/resume processes where polling mode is always
used) before advance_transaction() is invoked ("wait polling" log is
added before wait_event_timeout()). We can see 2 wait_event_timeout()
invocations. This is because time_after() ensures a ">" validation while
we only need a ">=" validation here:
[ 86.739909] ACPI: Waking up from system sleep state S3
[ 86.742857] ACPI : EC: 2: Increase command
[ 86.742859] ACPI : EC: ***** Command(RD_EC) started *****
[ 86.742861] ACPI : EC: ===== TASK (0) =====
[ 86.742871] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 86.742873] ACPI : EC: EC_SC(W) = 0x80
[ 86.742876] ACPI : EC: ***** Event started *****
[ 86.742880] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.743972] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.747966] ACPI : EC: ===== TASK (0) =====
[ 86.747977] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 86.747978] ACPI : EC: EC_DATA(W) = 0x06
[ 86.747981] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.751971] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.755969] ACPI : EC: ===== TASK (0) =====
[ 86.755991] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
[ 86.755993] ACPI : EC: EC_DATA(R) = 0x03
[ 86.755994] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.755995] ACPI : EC: ***** Command(RD_EC) stopped *****
[ 86.755996] ACPI : EC: 1: Decrease command
This patch corrects this by using time_before() instead in ec_guard():
[ 54.283146] ACPI: Waking up from system sleep state S3
[ 54.285414] ACPI : EC: 2: Increase command
[ 54.285415] ACPI : EC: ***** Command(RD_EC) started *****
[ 54.285416] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.285417] ACPI : EC: ===== TASK (0) =====
[ 54.285424] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 54.285425] ACPI : EC: EC_SC(W) = 0x80
[ 54.285427] ACPI : EC: ***** Event started *****
[ 54.285429] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.287209] ACPI : EC: ===== TASK (0) =====
[ 54.287218] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 54.287219] ACPI : EC: EC_DATA(W) = 0x06
[ 54.287222] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.291190] ACPI : EC: ===== TASK (0) =====
[ 54.291210] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
[ 54.291213] ACPI : EC: EC_DATA(R) = 0x03
[ 54.291214] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.291215] ACPI : EC: ***** Command(RD_EC) stopped *****
[ 54.291216] ACPI : EC: 1: Decrease command
After cleaning up all guarding logics, we have one single function
ec_guard() collecting all old, non-root-caused, hidden logics. Then we can
easily tune the logics in one place to respond to the bug reports.
Except the time_before() change, all other changes do not change the
behavior of the EC driver.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following commit merges polling and interrupt modes for EC driver:
Commit: 2a84cb9852 Mon Sep 17 00:00:00 2001
Subject: ACPI: EC: Merge IRQ and POLL modes
The irqs_disabled() check introduced in it tries to fall into busy polling
mode when the context of ec_poll() cannot sleep.
Actually ec_poll() is ensured to be invoked in the contexts that can sleep
(from a sysfs /sys/kernel/debug/ec/ec0/io access, or from
acpi_evaluate_object(), or from acpi_ec_gpe_poller()). Without the MSI
quirk, we never saw the udelay() logic invoked. Thus this check is useless
and can be removed.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch removes the storming threashold enlarging quirk.
After applying the following commit, we can notice that there is no no-op
GPE handling invocation can be observed, thus it is unlikely that the
no-op counts can exceed the storming threashold:
Commit: ca37bfdfbc
Subject: ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
Even when the storming happens, we have already limited its affection to
the only transaction and no further transactions will be affected. This is
done by this commit:
Commit: e1d4d90fc0
Subject: ACPI / EC: Refine command storm prevention support
So it's time to remove this quirk.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=45151
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates acpi_ec_is_gpe_raised() according to the following
commit:
Commit: 09af8e8290
Subject: ACPICA: Events: Add support to return both enable/status register values for GPE and fixed event.
This is actually a no-op change as both the flags are defined to a same
value.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the definition of struct acpi_predefined_names, value is of
type char *. Make the OSL override function also work with type
char * (or, more precisely, with a pointer to it).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make sure that async function scheduled with async_schedule() has already
been executed.
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If ACPI is disabled there's no need to schedule an async function call,
the driver initialization can be aborted earlier in acpi_battery_init().
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce invalid_phys_cpuid() to identify cpu with invalid
physical ID, then used it as replacement of the direct comparisons
with PHYS_CPUID_INVALID.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since invalid_logical_cpuid() can check error values, so
return specific error instead of -1 for acpi_map_cpuid().
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use pr->phys_id to replace phys_id to simplify the code.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Just use pr->id instead of cpu_index to simplify the code.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ACPI processor drivers, we use direct comparisons of cpu logical
id with -1 which are error prone in case logical cpuid is accidentally
assinged an error code and prevents us from returning an error-encoding
cpuid directly in some cases.
So introduce invalid_logical_cpuid() to identify cpu with invalid
logical cpu num, then it will be used to replace the direct comparisons
with -1.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit b1ef297258 (ACPICA: Permanently set _REV to the value
'2'.) as it causes a sound regression to happen on Dell XPS 13 (2015).
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
An old comment in acpi_power_transition() indicates that support
for ordering power resources needs to be added, but the current
code handles that already.
Drop the comment to avoid confusion.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
Since acpi_reserve_resources() is defined as a device_initcall(),
there's no guarantee that it will be executed in the right order
with respect to the rest of the ACPI initialization code. On some
systems this leads to breakage if, for example, the address range
that should be reserved for the ACPI fixed registers is given to
the PCI host bridge instead if the race is won by the wrong code
path.
Fix this by turning acpi_reserve_resources() into a void function
and calling it directly from within the ACPI initialization sequence.
Reported-and-tested-by: George McCollister <george.mccollister@gmail.com>
Link: http://marc.info/?t=143092384600002&r=1&w=2
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI procfs power interface is initialized by compilation units
that are only selectable on X86 platforms. Since its usage is
deprecated and it cannot even be used on platforms other than X86
it should be compiled in only on X86 platforms.
This patch makes CONFIG_ACPI_PROCFS_POWER dependent on X86, so
that other architectures are prevented from compiling it in for
no purpose.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Refine the check for the presence of the "compatible" property
if the PRP0001 device ID is present in the device's list of
ACPI/PNP IDs to also print the message if _DSD is missing
entirely or the format of it is incorrect.
One special case to take into accout is that the "compatible"
property need not be provided for devices having the PRP0001
device ID in their lists of ACPI/PNP IDs if they are ancestors
of PRP0001 devices with the "compatible" property present.
This is to cover heriarchies of device objects where the kernel
is only supposed to use a struct device representation for the
topmost one and the others represent, for example, functional
blocks of a composite device.
While at it, reduce the log level of the message to "info"
and reduce the log level of the "broken _DSD" message to
"debug" (noise reduction).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently you can specify the weight of the cooling device in the device
tree but that information is not populated to the
thermal_bind_params where the fair share governor expects it to
be. The of thermal zone device doesn't have a thermal_bind_params
structure and arguably it's better to pass the weight inside the
thermal_instance as it is specific to the bind of a cooling device to a
thermal zone parameter.
Core thermal code is fixed to populate the weight in the instance from
the thermal_bind_params, so platform code that was passing the weight
inside the thermal_bind_params continue to work seamlessly.
While we are at it, create a default value for the weight parameter for
those thermal zones that currently don't define it and remove the
hardcoded default in of-thermal.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Kapileshwar Singh <kapileshwar.singh@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This is the result of us seeing this during boot
[ 24.332560] INFO: NMI handler (ghes_notify_nmi) took too long to run: 3.265 msecs
[ 24.332567] INFO: NMI handler (ghes_notify_nmi) took too long to run: 5.946 msecs
[ 24.332568] INFO: NMI handler (ghes_notify_nmi) took too long to run: 5.948 msecs
and a report of people running perf stat and the machine softlocking.
"hest_disable" was helping in this case, which made us look at that
particular NMI handler. It was grabbing a lock each time it is run and
on each CPU. But this is not needed as the GHES sources are global and
they need only a single reader.
This patchset does that and cleans up the handler in the process.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Qj+0
-----END PGP SIGNATURE-----
Merge tag 'ras_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into acpi-apei
Pull GHES changes for 4.2 from Borislav Petkov:
"GHES: Seriously speedup and cleanup NMI handler (Jiri Kosina and Borislav Petkov)
This is the result of us seeing this during boot
[ 24.332560] INFO: NMI handler (ghes_notify_nmi) took too long to run: 3.265 msecs
[ 24.332567] INFO: NMI handler (ghes_notify_nmi) took too long to run: 5.946 msecs
[ 24.332568] INFO: NMI handler (ghes_notify_nmi) took too long to run: 5.948 msecs
and a report of people running perf stat and the machine softlocking.
"hest_disable" was helping in this case, which made us look at that
particular NMI handler. It was grabbing a lock each time it is run and
on each CPU. But this is not needed as the GHES sources are global and
they need only a single reader.
This patchset does that and cleans up the handler in the process."
* tag 'ras_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
GHES: Make NMI handler have a single reader
GHES: Elliminate double-loop in the NMI handler
GHES: Panic right after detection
GHES: Carve out the panic functionality
GHES: Carve out error queueing in a separate function
Commit eec15edbb0 (ACPI / PNP: use device ID list for PNPACPI device
enumeration) changed the way how ACPI devices are enumerated and when
they are added to the PNP bus.
However, it broke the sound card support on (at least) a vintage
IBM ThinkPad 600E: with said commit applied, two of the necessary
"CSC01xx" devices are not added to the PNP bus and hence can not be
found during the initialization of the "snd-cs4236" module. As a
consequence, loading "snd-cs4236" causes null pointer exceptions.
The attached patch fixes the problem end re-enables sound on the
IBM ThinkPad 600E.
Fixes: eec15edbb0 (ACPI / PNP: use device ID list for PNPACPI device enumeration)
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7bc5a2bad0 'ACPI: Support _OSI("Darwin") correctly' caused
the MacBook firmware to expose the SBS, resulting in intermittent
hangs of several minutes on boot, and failure to detect or report
the battery. Fix this by adding a 5 us delay to the start of each
SMBUS transaction. This timing is the result of experimentation -
hangs were observed with 3 us but never with 5 us.
Fixes: 7bc5a2bad0 'ACPI: Support _OSI("Darwin") correctly'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94651
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
An IO port or MMIO resource assigned to a PCI host bridge may be
consumed by the host bridge itself or available to its child
bus/devices. The ACPI specification defines a bit (Producer/Consumer)
to tell whether the resource is consumed by the host bridge itself,
but firmware hasn't used that bit consistently, so we can't rely on it.
Before commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource
interfaces to simplify implementation"), arch/x86/pci/acpi.c ignored
all IO port resources defined by acpi_resource_io and
acpi_resource_fixed_io to filter out IO ports consumed by the host
bridge itself.
Commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource interfaces
to simplify implementation") started accepting all IO port and MMIO
resources, which caused a regression that IO port resources consumed
by the host bridge itself became available to its child devices.
Then commit 63f1789ec7 ("x86/PCI/ACPI: Ignore resources consumed by
host bridge itself") ignored resources consumed by the host bridge
itself by checking the IORESOURCE_WINDOW flag, which accidently removed
MMIO resources defined by acpi_resource_memory24, acpi_resource_memory32
and acpi_resource_fixed_memory32.
On x86 and IA64 platforms, all IO port and MMIO resources are assumed
to be available to child bus/devices except one special case:
IO port [0xCF8-0xCFF] is consumed by the host bridge itself
to access PCI configuration space.
So explicitly filter out PCI CFG IO ports[0xCF8-0xCFF]. This solution
will also ease the way to consolidate ACPI PCI host bridge common code
from x86, ia64 and ARM64.
Related ACPI table are archived at:
https://bugzilla.kernel.org/show_bug.cgi?id=94221
Related discussions at:
http://patchwork.ozlabs.org/patch/461633/https://lkml.org/lkml/2015/3/29/304
Fixes: 63f1789ec7 (Ignore resources consumed by host bridge itself)
Reported-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 9faf6136ff (ACPI / SBS: Disable smart battery manager on
Apple) introduced a regression disabling the SBS battery manager.
The battery manager should be marked as present when
acpi_manager_get_info() returns 0.
Fixes: 9faf6136ff (ACPI / SBS: Disable smart battery manager on Apple)
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since GHES sources are global, we theoretically need only a single CPU
reading them per NMI instead of a thundering herd of CPUs waiting on a
spinlock in NMI context for no reason at all.
Do that.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
There's no real need to iterate twice over the HW error sources in the
NMI handler. With the previous cleanups, elliminating the second loop is
almost trivial.
Signed-off-by: Borislav Petkov <bp@suse.de>
The moment we log an error of panic severity, there's no need to noodle
through the ghes_nmi list anymore. So panic instead right then and
there.
Signed-off-by: Borislav Petkov <bp@suse.de>
- Fix a build warning in the intel_pstate driver showing up in non-SMP
builds (Borislav Petkov).
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi).
- Fix a NULL pointer dereference in the ACPI EC driver due to an unsafe
list walk in the query handler removal routine (Chris Bainbridge).
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki).
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki).
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian).
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu).
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0bKD
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
cpupower tool), a new CPU ID for the Intel RAPL driver and one
intel_pstate driver improvement that didn't make it to my previous
pull requests due to timing.
Specifics:
- Fix a build warning in the intel_pstate driver showing up in
non-SMP builds (Borislav Petkov)
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi)
- Fix a NULL pointer dereference in the ACPI EC driver due to an
unsafe list walk in the query handler removal routine (Chris
Bainbridge)
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki)
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki)
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian)
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu)
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach)"
* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Add a scan handler for PRP0001
ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
MAINTAINERS: remove maintainship entry of docking station driver
powercap / RAPL: Add support for Intel Skylake processors
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
cpupower: fix breakage from libpci API change
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
If the special PRP0001 device ID is present in the given device's list
of ACPI/PNP IDs and the device has a valid "compatible" property in
the _DSD, it should be enumerated using the default mechanism,
unless some scan handlers match the IDs preceding PRP0001 in the
device's list of ACPI/PNP IDs. In addition to that, no scan handlers
matching the IDs following PRP0001 in that list should be attached
to the device.
To make that happen, define a scan handler that will match PRP0001
and trigger the default enumeration for the matching devices if the
"compatible" property is present for them.
Since that requires the check for platform_id and device->handler
to be removed from acpi_default_enumeration(), move the fallback
invocation of acpi_default_enumeration() to acpi_bus_attach()
(after it's checked if there's a matching ACPI driver for the
device), which is a better place to call it, and do the platform_id
check in there too (device->handler is guaranteed to be unset at
the point where the function is looking for a matching ACPI driver).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
acpi_scan_is_offline() may be called under the physical_node_lock
lock of the given device object's parent, so prevent lockdep from
complaining about that by annotating that instance with
SINGLE_DEPTH_NESTING.
Fixes: caa73ea158 (ACPI / hotplug / driver core: Handle containers in a special way)
Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use list_for_each_entry_safe for iterating because handler may be freed
in the loop.
BUG: unable to handle kernel NULL pointer dereference at 000000000000002c
IP: [<ffffffff814d69c8>] acpi_ec_put_query_handler+0x7/0x1a
Call Trace:
acpi_ec_remove_query_handler+0x87/0x97
acpi_smbus_hc_remove+0x2a/0x44 [sbshc]
acpi_device_remove+0x7b/0x9a
__device_release_driver+0x7e/0x110
driver_detach+0xb0/0xc0
bus_remove_driver+0x54/0xe0
driver_unregister+0x2b/0x60
acpi_bus_unregister_driver+0x10/0x12
acpi_smb_hc_driver_exit+0x10/0x12 [sbshc]
SyS_delete_module+0x1b8/0x210
system_call_fastpath+0x12/0x6a
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix for a GPE handling regression on Dell Latitude D600 that
caused GPE signaling to stop working on that machine, which
appears to be due to a hardware glitch, but it used to work
and it can be made work again in a relativly straightforward
way (Rafael J Wysocki).
- Fix for a mutex unlock regression related to the handling of ACPI
tables introduced during the 3.16 development cycle (Octavian Purdila).
- _REV modification to always return 2 which has been done by all
versions of Windows since NT and the firmware people started to
use it to distinguish between OSes in their AML and do some silly
and wrong things on that basis (Bob Moore).
- Fixes and cleanups related to the acpi_physicall_address data type
including one stable-candidate fix for an issue occasionally occuring
on 64-bit machines running 32-bit kernels where using offsets provided
by the firmware may lead to address overflows (Lv Zheng).
- External() opcode support infrastructure needed for recompiling
disassembled ACPI tables in some cases including interpreter
modification to ignore that opcode (Bob Moore).
- Support for the "Windows 2015" string in _OSI (Bob Moore).
- GPE debug interface change to return values read from hardware
registers (Lv Zheng).
- Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).
- Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
Bob Moore).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xUhi
-----END PGP SIGNATURE-----
Merge tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"This updates the kernel's ACPICA code to upstream revision 20150410
and adds a fix for a GPE handling regression introduced during the
3.19 cycle on top of that.
Included are two stable-candidate bug fixes (one of them fixing a 3.16
regression), multiple other fixes and a bunch of cleanups.
Specifics:
- Fix for a GPE handling regression on Dell Latitude D600 that caused
GPE signaling to stop working on that machine, which appears to be
due to a hardware glitch, but it used to work and it can be made
work again in a relativly straightforward way (Rafael J Wysocki).
- Fix for a mutex unlock regression related to the handling of ACPI
tables introduced during the 3.16 development cycle (Octavian
Purdila).
- _REV modification to always return 2 which has been done by all
versions of Windows since NT and the firmware people started to use
it to distinguish between OSes in their AML and do some silly and
wrong things on that basis (Bob Moore).
- Fixes and cleanups related to the acpi_physicall_address data type
including one stable-candidate fix for an issue occasionally
occuring on 64-bit machines running 32-bit kernels where using
offsets provided by the firmware may lead to address overflows (Lv
Zheng).
- External() opcode support infrastructure needed for recompiling
disassembled ACPI tables in some cases including interpreter
modification to ignore that opcode (Bob Moore).
- Support for the "Windows 2015" string in _OSI (Bob Moore).
- GPE debug interface change to return values read from hardware
registers (Lv Zheng).
- Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).
- Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
Bob Moore)"
* tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Store GPE register enable masks upfront
ACPICA: Update version to 20150410.
ACPICA: Fix a couple issues with the local printf module.
ACPICA: Disassembler: Some cleanup of the table dump module.
ACPICA: iASL: Add support for MSDM ACPI table.
ACPICA: Update for SLIC ACPI table.
ACPICA: Add "//" before ascii output of buffers.
ACPICA: Remove unused internal AML opcode.
ACPICA: Permanently set _REV to the value '2'.
ACPICA: Add "Windows 2015" string to _OSI support.
ACPICA: Add infrastructure for External() opcode.
ACPICA: iASL: Enhancement for constant folding.
ACPICA: iASL/Disassembler: Add option to assume table contains valid AML.
ACPICA: Update AML Debugger global variables.
ACPICA: Update Resource descriptor dump module.
ACPICA: Fix a sscanf format string.
ACPICA: Casting changes around acpi_physical_address/acpi_size.
ACPICA: Resources: Correct conditional compilation definitions.
ACPICA: Utilities: Correct conditional compilation definitions.
ACPICA: Tables: Move an iasl specific table function to iasl source file.
...
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
It is reported that ACPI interrupts do not work any more on
Dell Latitude D600 after commit c50f13c672 (ACPICA: Save
current masks of enabled GPEs after enable register writes).
The problem turns out to be related to the fact that the
enable_mask and enable_for_run GPE bit masks are not in
sync (in the absence of any system suspend/resume events)
for at least one GPE register on that machine.
Address this problem by writing the enable_for_run mask into
enable_mask as soon as enable_for_run is updated instead of
doing that only after the subsequent register write has
succeeded. For consistency, update acpi_hw_gpe_enable_write()
to store the bit mask to be written into the GPE register
in enable_mask unconditionally before the write.
Since the ACPI_GPE_SAVE_MASK flag is not necessary any more after
that, drop it along with the symbols depending on it.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl>
Fixes: c50f13c672 (ACPICA: Save current masks of enabled GPEs after enable register writes)
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6853da4c0a99b49d62d6c58d22956cd6ff5759a9
The following commit has fixed local printf issue in width.prec:
Commit: 3589b8b8af
Subject: ACPICA: Utilities: Fix local printf issue.
But this commit only resets width/precision/quialifier to fix the reported
issue and doesn't fix other states issues. So now we still can see breakage
in format types and integer bases.
This patch resets format type/base states for local printf to fix this
issue. Lv Zheng.
Linux kernel is not affected by this patch as acpi_ut_vsnprintf() hasn't
been enabled in the kernel.
Link: https://github.com/acpica/acpica/commit/6853da4c
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 657dc227672709895df3192fa5ea59a649b9a76f
Updates the dump buffer utility to comment out the ASCII part
of buffer dump. Prevents some tools from getting confused.
Link: https://github.com/acpica/acpica/commit/657dc227
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3ec867764b079a98d8097d705c9f7b68270c04ec
This patch removes unused AML_INT_STATICSTRING_OP. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/3ec86776
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7af00219681ab35ebe57d64a9189fd04a5a026d8
Windows uses a value of 2, and has no plans to ever change this. So, _REV is
essentially useless for its primary purpose.
Worse, some BIOS vendors have used the difference in _REV values between
Windows and ACPICA to indicate which one is running.
It has been decided by the ACPI community to deprecate this method, and return
1 for ACPI 1.0 (32-bit integers) and 2 for ACPI 2.0 and greater (both 32-bit
and 64-bit integers.
ACPICA is changed to reflect this.
Link: https://github.com/acpica/acpica/commit/7af00219
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b293f602a67da478ae0bec129e68bd99787d9908
This change adds this string for Windows 10.
Link: https://github.com/acpica/acpica/commit/b293f602
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit d115fe2ffdab449d6107d58580c5afd0a81d65fe
This change adds the basic low-level infrastructure for the External
AML opcode. The interpreter will simply ignore this op, as the op
is intended for use by the disassembler only.
Note that External() opcode is useful for disassembler, interpreter
can simply ignore it and still return exceptions for unknown control
methods so the kernel part only includes the grammar definition of
External() opcode in order to ignore it but doesn't interpret it.
Link: https://github.com/acpica/acpica/commit/d115fe2f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 4f9e950d41cd6f6c704d5d6cf518647620d65e99
Add support to fold expressions with a target operand -- these are
folded and converted to a Store operator:
Add (4, 3, INT1) --> Store (7, INT1)
Also supports ASL+ constructs:
INT1 = 4 + 3 --> Store (7, INT1)
Linux kernel is not affected by this patch.
Link: https://github.com/acpica/acpica/commit/4f9e950d
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f5d2ff3fa05341d9fe27250fcb2e14c7f871432c
For dynamically loaded tables that have unknown ACPI signatures,
this option (-df) forces the disassembler to treat the table as if
it contains valid AML code (like a DSDT or SSDT). Otherwise, the
disassembler will treat the table as an unkown data table and
simply do a hex dump of the table.
Linux kernel is not affected by this patch.
Link: https://github.com/acpica/acpica/commit/f5d2ff3f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f65d0e5b880860a6da0c336b7c48139d1469f5b4
- Remove unused variables
- Update to use standard naming/capitalization convention.
Linux kernel is not affected by this patch.
Link: https://github.com/acpica/acpica/commit/f65d0e5b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 184f3cc4d162a6b6b2005eacd8be2fe55f19a245
- Change global #ifdef to check for ACPI_DEBUGGER only.
- Cleanup some long lines and misaligned code.
Link: https://github.com/acpica/acpica/commit/184f3cc4
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 46dc081e570b1363af1e368980201cbb65c4100f
Update for some recent changes, detected by MSVC and FreeBSD builds.
Link: https://github.com/acpica/acpica/commit/46dc081e
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f92a08512b0b35dce4a7fc6a73216674a3c2541b
Some conditional compilation definitions are wrong across header and source
files. This patch corrects them for the resources component.
NOTE that a further patch in this patchset cleans up all ACPI_EXEC_APP,
converting them into ACPI_DEBUGGER, including part of this change.
Link: https://github.com/acpica/acpica/commit/f92a0851
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9a5982afbebc56289c4834b5f6dac87e0f04af14
Some conditional compilation definitions are wrong across header and source
files. This patch corrects them for the utilities component.
Link: https://github.com/acpica/acpica/commit/9a5982af
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6eb364d790dd103bd4990f808e0095a421c437cb
acpi_tb_store_table() implements a logic that is only correct to iasl. So it
won't be used by any other utilities except iasl. This function is
complained by the kernel users as an unused function. The best choice to
stop releasing it to the Linux kernel should be moving it to adisasm.c.
ACPI table manager can use both struct acpi_table_desc (direct referencing)
and table index (indirect referencing) as the descriptor to the table, so
acpi_tb_get_next_root_index() is extended to return both of them to allow
maximum usability from the callers. NOTE that indirect referencing is a
design result to meet the boot stage static allocation requirement for the
table descriptors.
This is a linuxized acpi_tb_store_table() removing result, there should be
no functional changes introduced to the Linux kernel by this patch except
the additonal kernel unused argument for acpi_tb_get_next_root_index()
(renamed to acpi_tb_get_next_root_index()). This argument is used in the
ACPICA upstream.
Link: https://github.com/acpica/acpica/commit/6eb364d7
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 2a9ebd974aee41391f4b0edcd4f0cc5ee23ec2f8
Remove the function acpi_ut_create_pkg_state_and_push() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Link: https://github.com/acpica/acpica/commit/2a9ebd97
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3d9fb6d1f216a78ad098d3ad23f1304376c2f4ef
The macro __DATE__ and friends is not allowed in the Linux kernel. Also,
including the build time in output doesn't seem to provide any value.
Link: https://github.com/acpica/acpica/commit/3d9fb6d1
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit e25d791e4b3d5b9f4ead298269610cb05f89749a
There is a facility in Linux, developers can obtain GPE and fixed event
status via /sys/firmware/interrupts/. This is implemented using
acpi_get_event_status() and acpi_get_gpe_status(). Recently while debugging some
GPE race issues, it is found that the facility is lacking in the ability to
obtain real hardware register values, the confusing information makes
debugging difficult.
This patch modifies acpi_get_gpe_status() to return EN register values to fix
this gap. Then flags returned from acpi_get_event_status() and
acpi_get_gpe_status() are also cleaned up to reflect this change.
The old ACPI_EVENT_FLAG_SET is carefully kept to avoid regressions. It can
be deleted after we can make sure all its references are removed from OSPM
code. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/e25d791e
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c70434d4da13e65b6163c79a5aa16b40193631c7
ACPI_MTX_TABLES is acquired and released by the callers of
acpi_tb_install_standard_table() so releasing it in the function itself is
causing the following error in Linux kernel if the table is reloaded:
ACPI Error: Mutex [0x2] is not acquired, cannot release (20141107/utmutex-321)
Call Trace:
[<ffffffff81b0bd48>] dump_stack+0x4f/0x7b
[<ffffffff81546bf5>] acpi_ut_release_mutex+0x47/0x67
[<ffffffff81544357>] acpi_load_table+0x73/0xcb
Link: https://github.com/acpica/acpica/commit/c70434d4
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT
and ACPI_FORMAT_UINT64() instead of
ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT().
This patch also removes above replaced macros as there are no users.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/b6061237
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7f06739db43a85083a70371c14141008f20b2198
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to
convert the %p formats.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: https://github.com/acpica/acpica/commit/7f06739d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 154f6d074dd38d6ebc0467ad454454e6c5c9ecdf
There are code pieces converting pointers using "(acpi_physical_address) x"
or "ACPI_CAST_PTR (t, x)" formats, this patch cleans up them.
Known issues:
1. Cleanup of "(ACPI_PHYSICAL_ADDRRESS) x" for a table field
For the conversions around the table fields, it is better to fix it with
alignment also fixed. So this patch doesn't modify such code. There
should be no functional problem by leaving them unchanged.
Link: https://github.com/acpica/acpica/commit/154f6d07
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c327986430b7eb170c17d0f45735fe71bb62a810
The conversion converts an acpi_physical_address to acpi_physical_address,
this patch thus removes such useless conversion.
Link: https://github.com/acpica/acpica/commit/c3279864
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7d9fd64397d7c38899d3dc497525f6e6b044e0e3
OSPMs like Linux expect an acpi_physical_address returning value from
acpi_find_root_pointer(). This triggers warnings if sizeof (acpi_size) doesn't
equal to sizeof (acpi_physical_address):
drivers/acpi/osl.c:275:3: warning: passing argument 1 of 'acpi_find_root_pointer' from incompatible pointer type [enabled by default]
In file included from include/acpi/acpi.h:64:0,
from include/linux/acpi.h:36,
from drivers/acpi/osl.c:41:
include/acpi/acpixf.h:433:1: note: expected 'acpi_size *' but argument is of type 'acpi_physical_address *'
This patch corrects acpi_find_root_pointer().
Link: https://github.com/acpica/acpica/commit/7d9fd643
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch reduces source code differences between the Linux kernel and the
ACPICA upstream so that the linuxized ACPICA 20150410 release can be
applied with reduced human intervention.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
Commit e1acdeb0e7 "ACPI / scan: Simplify acpi_match_device()"
introduced code that may lead to a NULL pointer dereference when
trying to unlock a mutex. Fix that.
Fixes: e1acdeb0e7 "ACPI / scan: Simplify acpi_match_device()"
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- clockevents state machine cleanups and enhancements (Viresh Kumar)
- clockevents broadcast notifier horror to state machine conversion
and related cleanups (Thomas Gleixner, Rafael J Wysocki)
- clocksource and timekeeping core updates (John Stultz)
- clocksource driver updates and fixes (Ben Dooks, Dmitry Osipenko,
Hans de Goede, Laurent Pinchart, Maxime Ripard, Xunlei Pang)
- y2038 fixes (Xunlei Pang, John Stultz)
- NMI-safe ktime_get_raw_fast() and general refactoring of the clock
code, in preparation to perf's per event clock ID support (Peter
Zijlstra)
- generic sched/clock fixes, optimizations and cleanups (Daniel
Thompson)
- clockevents cpu_down() race fix (Preeti U Murthy)"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
timers/PM: Drop unnecessary braces from tick_freeze()
timers/PM: Fix up tick_unfreeze()
timekeeping: Get rid of stale comment
clockevents: Cleanup dead cpu explicitely
clockevents: Make tick handover explicit
clockevents: Remove broadcast oneshot control leftovers
sched/idle: Use explicit broadcast oneshot control function
ARM: Tegra: Use explicit broadcast oneshot control function
ARM: OMAP: Use explicit broadcast oneshot control function
intel_idle: Use explicit broadcast oneshot control function
ACPI/idle: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast oneshot control function
x86/amd/idle, clockevents: Use explicit broadcast oneshot control functions
clockevents: Provide explicit broadcast oneshot control functions
clockevents: Remove the broadcast control leftovers
ARM: OMAP: Use explicit broadcast control function
intel_idle: Use explicit broadcast control function
cpuidle: Use explicit broadcast control function
ACPI/processor: Use explicit broadcast control function
ACPI/PAD: Use explicit broadcast control function
...
* device-properties:
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
driver core: Implement device property accessors through fwnode ones
driver core: property: Update fwnode_property_read_string_array()
driver core: Add comments about returning array counts
ACPI: Introduce has_acpi_companion()
driver core / ACPI: Represent ACPI companions using fwnode_handle
* acpi-scan:
ACPI / scan: Rework modalias creation when "compatible" is present
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
ACPI / scan: fix fixed event handler return value
* acpi-pm:
ACPI / PM: Enable all wakeup GPEs in suspend-to-idle
ACPI / sleep: Drop acpi_suspend() which is not used
* acpi-enumeration:
ACPI: Add acpi_device_uid() for convenience
ACPI: Update GPIO documentation to mention _DSD
* acpi-sysfs:
ACPI / sysfs: Treat the count field of counter_show() as unsigned
Currently, the ACPI modalias creation covers two mutually exclusive
cases: If the PRP0001 device ID is present in the device's list of
ACPI/PNP IDs and the "compatible" property is present in _DSD, the
created modalias will follow the OF rules of modalias creation.
Otherwise, ACPI rules are used.
However, that is not really desirable, because the presence of PRP0001
in the list of device IDs generally does not preclude using other
ACPI/PNP IDs with that device and those other IDs may be of higher
priority. In those cases, the other IDs should take preference over
PRP0001 and therefore they also should be present in the modalias.
For this reason, rework the modalias creation for ACPI so that it
shows both the ACPI-style and OF-style modalias strings if the
device has a non-empty list of ACPI/PNP IDs (other than PRP0001)
and a valid "compatible" property at the same time.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the special PRP0001 device ID is present in a device's _CID list,
it should not prevent any ACPI/PNP IDs preceding it in the device's
list of identifiers from being matched first. That is, only if none
of the IDs preceding PRP0001 in the device's PNP/ACPI IDs list
matches the IDs recognized by the driver, the driver's list of
"compatible" IDs should be matched against the device's "compatible"
property, if present.
In addition to that, drivers can provide both acpi_match_table and
of_match_table at the same time and the of_compatible matching
should be used in that case too if PRP0001 is present in the
device's list of identifiers.
To make that happen, rework acpi_driver_match_device() to do the
"compatible" property check in addition to matching the driver's
list of ACPI IDs against the device's one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Redefine acpi_companion_match() to return an ACPI device object
pointer instead of a bool and use it to remove some redundant code
from acpi_match_device().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Redefine the function used for matching the device's "compatible"
property against a given list of "compatible" strings to take
a pointer to that list instead of a driver object pointer to
make it more general.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pci/misc:
PCI: Read capability list as dwords, not bytes
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
Communications with a hardware vendor confirm that the expected behaviour
on systems that set the FADT ASPM disable bit but which still grant full
PCIe control is for the OS to leave any BIOS configuration intact and
refuse to touch the ASPM bits. This mimics the behaviour of Windows.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a bug that leads to showing the name and description of C-state C0
as "<null>" in sysfs after the ACPI C-states changed (e.g. after AC->DC
or DC->AC
transition).
The function poll_idle_init() in drivers/cpuidle/driver.c initializes the
state 0 during cpuidle_register_driver(), so we better do not overwrite it
again with '\0' during acpi_processor_cst_has_changed().
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/2653377.MSAlfA939I@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1552509.UntNmyqF5v@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/25071624.dkenaL3SGT@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace the clockevents_notify() call with an explicit function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1521832.mm0ZfkTzTA@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While looking through the (ab)use of the clockevents_notify()
function I stumbled over the following gem in the acpi_pad code:
if (lapic_detected_unstable && !lapic_marked_unstable) {
/* LAPIC could halt in idle, so notify users */
for_each_online_cpu(i)
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &i);
lapic_marked_unstable = 1;
}
This code calls on the cpu which detects the lapic unstable
condition first clockevents_notify() to tell the core code that
the broadcast should be enabled on all online cpus. Brilliant
stuff that as it notifies the core code a num_online_cpus()
times that the broadcast should be enabled on the current cpu.
This probably has never been noticed because that code got never
tested with NOHZ=n and HIGHRES_TIMER=n or it just worked by
chance because one of the other mechanisms told the core in the
right way that the local apic timer is wreckaged.
Sigh, this is:
- The 4th incarnation of idle drivers which has their own mechanism
to detect and deal with X86_FEATURE_ARAT.
- The 2nd incarnation of fake idle mechanisms with a different set of
brainmelting bugs.
- Has been merged against an explicit NAK of the scheduler
maintainer with the promise to improve it over time.
- Another example of featuritis driven trainwreck engineering.
- Another pointless waste of my time.
Fix this nonsense by removing that lapic detection and
notification logic and simply call into the clockevents code
unconditonally. The ARAT feature is marked in the lapic
clockevent already so the core code will just ignore the
requests and return.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1887788.RObRuI4tSv@vostro.rjw.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On some machines(E,G Mircosoft surface 3), ACPI battery depends on
the EC operation region and it has _DEP method which contains EC.
Current code doesn't support such devices whose dep_unmet will be
not be decreased after EC opregion handler being installed. This
blocks battery device to be attached with its driver. This patch
is to fix the issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=90161
Reported-and-tested-by: Lompik <lompik@voila.fr>
Tested-by: Valentin Lab <valentin.lab_bugzilla.kernel.org@kalysto.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, in suspend-to-idle, wakeup GPE for PCI devices are
handled properly because acpi_pci_sleep_wake() invokes acpi_enable_gpe()
to enable the wakeup GPE directly. But for the other wakeup-capable
devices in ACPI bus, acpi_enable_wakeup_devices() should be invoked
to update enable_for_wake mask in gpe_register_info structure, thus
acpi_enable_all_wakeup_gpes() can enable the wakeup GPE referred in
_PRW methods. And acpi_disable_wakeup_devices() will be called
before disable_irq_wake() in acpi_freeze_restore() to restore the mask.
This patch fixes a power button wakeup problem on Surface Pro 3,
on which platform power button uses EC to deliver event
(EC GPE is referred in _PRW).
Note: enabling EC GPE during freeze state may bring some risks
because EC events are expected to fire more frequently than others.
Thus it may bring the system out of freeze state unnecessarily.
(We already have comments about this in bugzilla)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84651
Reported-and-tested-by: Ethan Schoonover <es@ethanschoonover.com>
Tested-by: Peter Amidon <psa.pub.0@picnicpark.org>
Tested-by: Yani Ioadnnou <yani.ioannou@gmail.com>
Tested-by: Mister Wardrop <mister.wardrop@gmail.com>
Tested-by: Anton Anikin <anton@anikin.name>
Tested-by: Keith McClelland <zismylaptop@gmail.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fix a spelling typo in MODULE_DESCRIPTION within intel_pmic_crc.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code deployed to implement GSI linux IRQ numbers mapping on arm64 turns
out to be generic enough so that it can be moved to ACPI core code along
with its respective config option ACPI_GENERIC_GSI selectable on
architectures that can reuse the same code.
Current ACPI IRQ mapping code is not integrated in the kernel IRQ domain
infrastructure, in particular there is no way to look-up the
IRQ domain associated with a particular interrupt controller, so this
first version of GSI generic code carries out the GSI<->IRQ mapping relying
on the IRQ default domain which is supposed to be always set on a
specific architecture in case the domain structure passed to
irq_create/find_mapping() functions is missing.
This patch moves the arm64 acpi functions that implement the gsi mappings:
acpi_gsi_to_irq()
acpi_register_gsi()
acpi_unregister_gsi()
to ACPI core code. Since the generic GSI<->domain mapping is based on IRQ
domains, it can be extended as soon as a way to map an interrupt
controller to an IRQ domain is implemented for ACPI in the IRQ domain
layer.
x86 and ia64 code for GSI mappings cannot rely on the generic GSI
layer at present for legacy reasons, so they do not select the
ACPI_GENERIC_GSI config options and keep relying on their arch
specific GSI mapping layer.
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add Kconfigs to build ACPI on ARM64, and make ACPI available on ARM64.
acpi_idle driver is x86/IA64 dependent now, so make CONFIG_ACPI_PROCESSOR
depend on X86 || IA64, and implement it on ARM64 in the future.
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Introduce ACPI_IRQ_MODEL_GIC which is needed for ARM64 as GIC is
used, and then register device's gsi with the core IRQ subsystem.
acpi_register_gsi() is similar to DT based irq_of_parse_and_map(),
since gsi is unique in the system, so use hwirq number directly
for the mapping.
We are going to implement stacked domains when GICv2m, GICv3, ITS
support are added.
CC: Marc Zyngier <marc.zyngier@arm.com>
Originally-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Introduce a new function map_gicc_mpidr() to allow MPIDRs to be obtained
from the GICC Structure introduced by ACPI 5.1, since MPIDR for ARM64 is
64-bit, so typedef u64 for phys_cpuid_t.
The ARM architecture defines the MPIDR register as the CPU hardware
identifier. This patch adds the code infrastructure to retrieve the MPIDR
values from the ARM ACPI GICC structure in order to look-up the kernel CPU
hardware ids required by the ACPI core code to identify CPUs.
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CPU hardware ID (phys_id) is defined as u32 in structure acpi_processor,
but phys_id is used as int in acpi processor driver, so it will lead to
some inconsistence for the drivers.
Furthermore, to cater for ACPI arch ports that implement 64 bits CPU
ids a generic CPU physical id type is required.
So introduce typedef u32 phys_cpuid_t in a common file, and introduce
a macro PHYS_CPUID_INVALID as (phys_cpuid_t)(-1) if it's not defined
by other archs, this will solve the inconsistence in acpi processor driver,
and will prepare for the ACPI on ARM64 for the 64 bit CPU hardware ID
in the following patch.
CC: Rafael J Wysocki <rjw@rjwysocki.net>
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[hj: reworked cpu physid map return codes]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When MADT is parsed, print GIC information as debug message:
ACPI: GICC (acpi_id[0x0000] address[00000000e112f000] MPIDR[0x0] enabled)
ACPI: GICC (acpi_id[0x0001] address[00000000e112f000] MPIDR[0x1] enabled)
...
ACPI: GICC (acpi_id[0x0201] address[00000000e112f000] MPIDR[0x201] enabled)
This debug information will be very helpful to bring up early systems to
see if acpi_id and MPIDR are matched or not as spec defined.
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ACPI 5.1 does not currently support S states for ARM64 hardware but
ACPI code will call acpi_target_system_state() and acpi_sleep_init()
for device power management, so introduce
CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT and select it for x86 and
ia64 only to make sleep functions available, and also introduce stub
function to allow other drivers to function until S states are defined
for ARM64.
It will be no functional change for x86 and IA64.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now with the base changes to the arm memory mapping it is safe
to convert to using ioremap to map in the tables after
acpi_gbl_permanent_mmap is set.
CC: Rafael J Wysocki <rjw@rjwysocki.net>
Tested-by: Robert Richter <rrichter@cavium.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For a normal 8 cpu sockets system, it will up to 240 cpu threads (Xeon E7
v2 family for now), and we need 240 entries for local apic or local x2apic
in MADT table, so it will be much verbose information printed with a slow
uart console when system booted, this will be even worse with large system
with 16/32 cpu sockets.
This patch just use pr_debug() instead of pr_info() for ioapic/iosapic,
local apic/x2apic/sapic structures when scanning the MADT table to remove
those verbose information, but leave other structures unchanged.
CC: Rafael J Wysocki <rjw@rjwysocki.net>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Lenovo Ideapad Z570 (which is an Acer in disguise like some other Ideapads)
has a broken acpi_video interface, this was fixed in commmit a11d342fb8
("ACPI / video: force vendor backlight on Lenovo Ideapad Z570").
Which stops acpi_video from registering a backlight interface, but this is
only a partial fix, because for people who have the ideapad-laptop module
installed that module will now register a backlight interface, which also
does not work, so we need to use the native intel_backlight interface.
The Lenovo Ideapad 570 is a pre-win8 laptop / too old for the acpi-video code
to automatically prefer the native backlight interface, so add a quirk for it.
This commit also removes the previous incomplete fix.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1187004
Tested-by: Be <be.0@gmx.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The native backlight behavior (so not registering both the acpi-video
and the vendor backlight driver) can be useful on some non win8 machines
too, so change the behavior of the video.use_native_backlight=1 or 0
kernel cmdline option to be: if user has set video.use_native_backlight=1
or 0, use that no matter if it is a win8 system or not. Also, we will
put some known systems into the DMI table to make them either use native
backlight interface or not, and the use_native_backlight_dmi is used to
reflect that.
Original-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit b4b55cda58 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda58 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_suspend() function has no callers, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
The fixed event handler should return a value that is either 0 or 1
meanning if the event is handled or not, instead of an acpi_status to
mean if the handler runs well or not.
Suggested-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that the ACPI companions of devices are represented by pointers
to struct fwnode_handle, it is not quite efficient to check whether
or not an ACPI companion of a device is present by evaluating the
ACPI_COMPANION() macro.
For this reason, introduce a special static inline routine for that,
has_acpi_companion(), and update the code to use it where applicable.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have struct fwnode_handle, we can use that to point to
ACPI companions from struct device objects instead of pointing to
struct acpi_device directly.
There are two benefits from that. First, the somewhat ugly and
hackish struct acpi_dev_node can be dropped and, second, the same
struct fwnode_handle pointer can be used in the future to point
to other (non-ACPI) firmware device node types.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Sony VGN-SR19XN laptop needs to disable windows vista compatibility,
or else it freezes when plugging/unplugging the VGA connector.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=66771
Tested-by: Lionel Duriez <lionelduriez@hotmail.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.
The power_supply_register() function is changed so all power supply
drivers need updating.
When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.
When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
[for drivers/hid/*]
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The count field is an unsigned 32bit value, and the
counter_show() function should also treat it as a unsigned
value.
Otherwise the counter may show negative number as we found on a
machine:
...
gpe23: 0 invalid
gpe24: -2071733 enabled
gpe25: 0 invalid
...
gpe_all: -2070980
sci: -2070949
Signed-off-by: Nan Li <nli@suse.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enhances debugging with the GPE reference count messages added.
This kind of log entries can be used by the platform validators to validate
if there is an EC transaction broken because of firmware/driver bugs.
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch refines logging/debugging splitter support so that when DEBUG is
disabled, splitters won't be visible in the kernel logs while they are
still available for developers when DEBUG is enabled.
This patch also refines the splitters to mark the following handling
process boundaries:
+++++: boundary of driver starting/stopping
boundary of IRQ storming
=====: boundary of transaction advancement
*****: boundary of EC command
boundary of EC query
#####: boundary of EC _Qxx evaluation
The following 2 log entries are originally logged using pr_info() in order
to be used as the boot/suspend/resume log entries for the EC device, this
patch also restores them to pr_info() logging level:
ACPI : EC: EC started
ACPI : EC: EC stopped
In this patch, one log entry around "Polling quirk" is converted into
ec_dbg_raw() which doesn't contain the boundary marker.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7d78cbefaa (serial: 8250_dw: add ability to handle
the peripheral clock) introduces handling for a second clk
to 8250_dw.c which is the driver also for LPSS UART. The
second clk forces us to provide identifier (con_id) for the
clkdev we create.
This fixes an issue where 8250_dw.c is getting the same
handler for both clocks.
Fixes: 7d78cbefaa (serial: 8250_dw: add ability to handle the peripheral clock)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Report the actual error code from acpi_bus_register_driver(), it may
help future debugging (typically ENODEV as previously reported, but the
unusual cases are where it may help most).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.
Reported-by: Bill Augur <bill-auger@programmer.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Aaron Lu <aaron.lu@intel.com>
[ rjw: Fixed up the new comment in acpi_video_init() ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some BIOSes report incorrect length for ACPI address space descriptors,
so relax the checks to avoid regressions. This issue has appeared several
times as:
3162b6f0c5 ("PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
d558b483d5 ("x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
f238b414a7 ("PNPACPI: compute Address Space length rather than using _LEN")
48728e0774 ("x86/PCI: compute Address Space length rather than using _LEN")
Please refer to https://bugzilla.kernel.org/show_bug.cgi?id=94221
for more details and example malformed ACPI resource descriptors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94221
Fixes: 593669c2ac (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and Braswell
SoCs in case they have been left in wrong states by the platform
firmware which then may casuse fatal controller driver failures during
resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related to
ACPI resources that may become noisy in some cases (Rafael J Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native backlight
interface doesn't work while the ACPI based one does (Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed by
__release_region() instead of __check_region() which then will allow
us to get rid of the latter as it has no more users (Jakub Sitnicki).
- Fix a build breakage and an issue with two __init functions that may be
called after initialization in the s3c cpufreq driver (Arnd Bergmann).
- Make the powernv cpuidle driver read target_residency values for idle
states from a Device Tree (as we have the suitable DT bindings for that
now) and improve the parsing of the powermgmt DT node in that driver
(Preeti U Murthy).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=us59
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull one more batch of power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes on top of the previously merged recent PM and
ACPI material.
First, one commit that broke the ACPI LPSS (Low-Power Subsystem)
driver on a Dell box is reverted and there are two stable-candidate
fixes for that driver. Another fix cleans up two recently added ACPI
EC messages that look odd and the printk level of a noisy debug
message in the core ACPI resources handling code is reduced.
In addition to that we have two stable-candidate fixes for the s3c
cpufreq driver, two cpuidle powernv driver updates related to Device
Trees and a PNP subsystem cleanup that will allow us to get rid of
some old ugliness going forward. Also there is a new blacklist entry
for the ACPI backlight code.
Specifics:
- Revert a recent ACPI LPSS driver commit that prevented the touchpad
driver from loading on Dell XPS13 (Jarkko Nikula).
- Make the ACPI LPSS driver disable the I2C controllers and deassert
SPI host controllers resets at startup on Intel BayTrail and
Braswell SoCs in case they have been left in wrong states by the
platform firmware which then may casuse fatal controller driver
failures during resume from hibernation (Mika Westerberg).
- Make two recently added ACPI EC messages look better (Scot Doyle).
- Reduce the printk level of a recently added debug message related
to ACPI resources that may become noisy in some cases (Rafael J
Wysocki).
- Add a new ACPI backlight blacklist entry for Samsung Series 9
(900X3C/900X3D/900X3E/900X4C/900X4D) laptops where the native
backlight interface doesn't work while the ACPI based one does
(Jens Reyer).
- Make the PNP sybsystem's core code use __request_region() followed
by __release_region() instead of __check_region() which then will
allow us to get rid of the latter as it has no more users (Jakub
Sitnicki).
- Fix a build breakage and an issue with two __init functions that
may be called after initialization in the s3c cpufreq driver (Arnd
Bergmann).
- Make the powernv cpuidle driver read target_residency values for
idle states from a Device Tree (as we have the suitable DT bindings
for that now) and improve the parsing of the powermgmt DT node in
that driver (Preeti U Murthy)"
* tag 'pm+acpi-3.20-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: powernv: Avoid endianness conversions while parsing DT
cpufreq: s3c: remove last use of resume_clocks callback
cpufreq: s3c: remove incorrect __init annotations
ACPI / LPSS: Deassert resets for SPI host controllers on Braswell
ACPI / LPSS: Always disable I2C host controllers
ACPI / resources: Change pr_info() to pr_debug() for debug information
ACPI / video: Disable native backlight on Samsung Series 9 laptops
cpuidle: powernv: Read target_residency value of idle states from DT if available
Revert "ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C"
ACPI / EC: Remove non-standard log emphasis
PNP: Switch from __check_region() to __request_region()
Pull thermal managament updates from Zhang Rui:
"Specifics:
- Abstract the code and introduce helper functions for all int340x
thermal drivers. From: Srinivas Pandruvada.
- Reorganize the ACPI LPAT table support code so that it can be
shared for both ACPI PMIC driver and int340x thermal driver.
- Add support for Braswell in intel_soc_dts thermal driver.
- a couple of small fixes/cleanups for step_wise governor and int340x
thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal/int340x_thermal: remove unused uuids.
thermal: step_wise: spelling fixes
thermal: int340x: fix sparse warning
Thermal/int340x: LPAT conversion for temperature
ACPI / PMIC: Use common LPAT table handling functions
ACPI / LPAT: Common table processing functions
thermal: Intel SoC DTS: Add Braswell support
Thermal/int340x/int3402: Provide notification support
Thermal/int340x/processor_thermal: Add thermal zone support
Thermal/int340x/int3403: Use int340x thermal API
Thermal/int340x/int3402: Use int340x thermal API
Thermal/int340x: Add common thermal zone handler
On some Braswell systems BIOS leaves resets for SPI host controllers
active. This prevents the SPI driver from transferring messages on wire.
Fix this in similar way that we do for I2C already by deasserting resets
for the SPI host controllers.
Reported-by: Yang A Fang <yang.a.fang@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Baytrail and Braswell the BIOS might leave the I2C host controllers
enabled, probably because it uses them for its own purposes. This is fine
in normal cases because the I2C driver will disable the hardware when it
is probed anyway.
However, in case of suspend to disk it is different story. If the driver
happens to be compiled as a module the boot kernel never loads the driver
thus leaving host controllers enabled upon loading the hibernation image.
The I2C host controller interrupt mask register has default value of 0x8ff,
in other words it has most of the interrupts unmasked. When combined with
the fact that the host controller is enabled, the driver immediately starts
getting interrupts even before its resume hook is called (once IO-APIC is
resumed). Since the driver is not prepared for this it will crash the
kernel due to NULL pointer derefence because dev->msgs is NULL.
Unfortunately we were not able to get full backtrace to from the console
which could be reproduced here.
In order to fix this even when the driver is compiled as module, we disable
the I2C host controllers in byt_i2c_setup() before devices are created.
Reported-by: Yu Chen <yu.c.chen@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Annoying and noisy ACPI debug messages are printed with pr_info()
after the recent ACPI resources handling rework. Replace the
pr_info() with pr_debug() to reduce to noise level.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add video_disable_native_backlight quirk for SAMSUNG 900X3C/900X3D/
900X3E/900X4C/900X4D laptops.
The native intel backlight controls do not work correctly on SAMSUNG
Series 9 (900X3C/900X3D/900X3E/900X4C/900X4D) laptops:
One machine has an completely dimmed (= black) display after boot at the
GDM login screen and brightness controls work only between 0 and 5%
(= no effect).
Another machine has the same brightness control issues if an external
HDMI monitor is or gets connected, although the initial brightness is
ok.
After login to Gnome both machines always work fine.
Tested on both machines.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=87286
Link: https://bugs.debian.org/772440
Signed-off-by: Jens Reyer <jens.reyer@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit b893e80e31 ("ACPI / LPSS: Remove non-existing clock control
from Intel Lynxpoint I2C") because it causes touchpad to not load on Dell
XPS13.
Regression is a clear indication that not only some early prototype version
of Lynxpoint I2C but also newer versions can be doing clock gating even
documentation does not state it.
Therefore it is best to revert since this clock gating haven't caused known
issues on those Lynxpoint version which don't do clock gating.
Reported-by-and-tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unusual pr_info() visual emphasis introduced in ad479e7f47
"ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag".
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
[ rjw: Change pr_info() to pr_debug() too in those places. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an ->enter_freeze callback routine, acpi_idle_enter_freeze(), to
the ACPI cpuidle driver and point ->enter_freeze to it for all the
C2-type and C3-type states that don't need to fall back to C1
(which may be halt-induced and that will re-enable interrupts on
exit from idle, which ->enter_freeze cannot do).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
- Revert two ACPI EC driver commits, one that broke system suspend
on Acer Aspire S5 and one that depends on it (Rafael J Wysocki).
- Fix a typo leading to an incorrect check in the exynos-ppmu devfreq
driver (Dan Carpenter).
- Add support for one more Broadwell CPU model to intel_idle (Len Brown).
- Fix an obscure problem with state transitions related to interrupts
in the speedstep-smi cpufreq driver (Mikulas Patocka).
- Remove some unnecessary messages related to the "out of memory"
condition from the core PM code (Quentin Lambert).
- Update turbostat parameters and documentation, add support for
one more Broadwell CPU model to it and modify it to skip
printing disabled package C-states (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=y7ew
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are two reverts related to system suspend breakage by one of a
recent commits, a fix for a recently introduced bug in devfreq and a
bunch of other things that didn't make it into my previous pull
request, but otherwise are ready to go.
Specifics:
- Revert two ACPI EC driver commits, one that broke system suspend on
Acer Aspire S5 and one that depends on it (Rafael J Wysocki).
- Fix a typo leading to an incorrect check in the exynos-ppmu devfreq
driver (Dan Carpenter).
- Add support for one more Broadwell CPU model to intel_idle (Len Brown).
- Fix an obscure problem with state transitions related to interrupts
in the speedstep-smi cpufreq driver (Mikulas Patocka).
- Remove some unnecessary messages related to the "out of memory"
condition from the core PM code (Quentin Lambert).
- Update turbostat parameters and documentation, add support for one
more Broadwell CPU model to it and modify it to skip printing
disabled package C-states (Len Brown)"
* tag 'pm+acpi-3.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: event: testing the wrong variable
cpufreq: speedstep-smi: enable interrupts when waiting
PM / OPP / clk: Remove unnecessary OOM message
Revert "ACPI / EC: Add query flushing support"
Revert "ACPI / EC: Add GPE reference counting debugging messages"
tools/power turbostat: support additional Broadwell model
intel_idle: support additional Broadwell model
tools/power turbostat: update parameters, documentation
tools/power turbostat: Skip printing disabled package C-states
__FUNCTION__ hasn't been treated as a string literal since gcc 3.4, so
this only helps people who only test-compile using 3.3 (compiler-gcc3.h
barks at anything older than that). Besides, there are almost no
occurrences of __FUNCTION__ left in the tree.
[akpm@linux-foundation.org: convert remaining __FUNCTION__ references]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit f252cb09e1 (ACPI / EC: Add query flushing support),
because it breaks system suspend on Acer Aspire S5. The machine
just hangs solid at the last stage of suspend (after taking non-boot
CPUs offline).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit b5bca896ef (ACPI / EC: Add GPE reference counting
debugging messages), because it depends on commit f252cb09e1
(ACPI / EC: Add query flushing support) which breaks system suspend
on Acer Aspire S5 and needs to be reverted.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
* acpi-resources: (23 commits)
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
x86/irq, ACPI: Implement ACPI driver to support IOAPIC hotplug
ACPI: Add interfaces to parse IOAPIC ID for IOAPIC hotplug
x86/PCI: Refine the way to release PCI IRQ resources
x86/PCI/ACPI: Use common ACPI resource interfaces to simplify implementation
x86/PCI: Fix the range check for IO resources
PCI: Use common resource list management code instead of private implementation
resources: Move struct resource_list_entry from ACPI into resource core
ACPI: Introduce helper function acpi_dev_filter_resource_type()
ACPI: Add field offset to struct resource_list_entry
ACPI: Translate resource into master side address for bridge window resources
ACPI: Return translation offset when parsing ACPI address space resources
ACPI: Enforce stricter checks for address space descriptors
ACPI: Set flag IORESOURCE_UNSET for unassigned resources
ACPI: Normalize return value of resource parser functions
ACPI: Fix a bug in parsing ACPI Memory24 resource
ACPI: Add prefetch decoding to the address space parser
ACPI: Move the window flag logic to the combined parser
ACPI: Unify the parsing of address_space and ext_address_space
ACPI: Let the parser return false for disabled resources
...
* acpi-processor:
ACPI / cpuidle: Common callback routine for entering states
ACPI / cpuidle: Merge acpi_idle_enter_c1() and acpi_idle_enter_simple()
ACPI / cpuidle: Drop flags.bm_check tests from acpi_idle_enter_bm()
ACPI / cpuidle: Clean up white space in a switch statement
ACPI / cpuidle: Drop irrelevant comment from acpi_idle_enter_simple()
ACPI / cpuidle: Clean up fallback to C1 checks
ACPI / cpuidle: Drop unnecessary calls from ->enter callback routines
ACPI / cpuidle: Drop unnecessary calls from acpi_idle_do_entry()
* acpi-doc:
MAINTAINERS / ACPI: add the necessary '/' according to entry rules
ACPI / Documentation: add a missing '='
* acpi-pm:
ACPI / sleep: mark acpi_sleep_dmi_check() __init
* acpi-pcc:
ACPI / PCC: Use pr_debug() for debug messages in pcc_init()
* acpi-tables:
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
* acpi-video:
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / video: Add disable_native_backlight quirk for Samsung 730U3E/740U3E
* acpi-soc:
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / LPSS: Remove non-existing clock control from Intel Lynxpoint I2C
ACPI / LPSS: check the result of ioremap()
* acpica:
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
ACPICA: Events: Introduce acpi_set_gpe()/acpi_finish_gpe() to reduce divergences
ACPICA: Events: Introduce ACPI_GPE_DISPATCH_RAW_HANDLER to fix 2 issues for the current GPE APIs
ACPICA: Update version to 20150204
ACPICA: Update Copyright headers to 2015
ACPICA: Hardware: Cast GPE enable_mask before storing
ACPICA: Events: Cleanup GPE dispatcher type obtaining code
ACPICA: Events: Cleanup to move acpi_gbl_global_event_handler invocation out of acpi_ev_gpe_dispatch()
ACPICA: Events: Cleanup of resetting the GPE handler to NULL before removing
ACPICA: Events: Fix uninitialized variable
ACPICA: Events: Remove acpi_ev_valid_gpe_event() due to current restriction
ACPICA: Events: Remove duplicated sanity check in acpi_ev_enable_gpe()
ACPICA: Events: Back port "ACPICA: Save current masks of enabled GPEs after enable register writes"
ACPICA: Resources: Provide common part for struct acpi_resource_address structures.
ACPI: Introduce acpi_unload_parent_table() usages in Linux kernel
ACPICA: take ACPI_MTX_INTERPRETER in acpi_unload_table_id()
Backlight control through the native intel interface does not work properly
on the Samsung 510R, where as using the acpi_video interface does work, add
a quirk for this.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1186097
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 5de21bb998 ("ACPI / PM: Drop CONFIG_PM_RUNTIME from the
ACPI core"), all occurrences of CONFIG_PM_RUNTIME were replaced with
CONFIG_PM. This created the following structure of #ifdef blocks in
the code:
[...]
#ifdef CONFIG_PM
#ifdef CONFIG_PM
/* always on / undead */
#ifdef CONFIG_PM_SLEEP
[...]
#endif
#endif
[...]
#endif
This patch removes the inner "#ifdef CONFIG_PM" block as it will
always be enabled when the outer block is enabled. This inconsistency
was found using the undertaker-checkpatch tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enhances debugging with the GPE reference count messages added.
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch implementes the QR_EC flushing support.
Grace periods are implemented from the detection of an SCI_EVT to the
submission/completion of the QR_EC transaction. During this period, all
EC command transactions are allowed to be submitted.
Note that query periods and event periods are intentionally distiguished to
allow further improvements.
1. Query period: from the detection of an SCI_EVT to the sumission of the
QR_EC command. This period is used for storming prevention, as currently
QR_EC is deferred to a work queue rather than directly issued from the
IRQ context even there is no other transactions pending, so malicous
SCI_EVT GPE can act like "level triggered" to trigger a GPE storm. We
need to be prepared for this. And in the future, we may change it to be
a part of the advance_transaction() where we will try QR_EC submission
in appropriate positions to avoid such GPE storming.
2. Event period: from the detection of an SCI_EVT to the completion of the
QR_EC command. We may extend it to the completion of _Qxx evaluation.
This is actually a grace period for event flushing, but we only flush
queries due to the reason stated in known issue 1. That's also why we
use EC_FLAGS_EVENT_xxx. During this period, QR_EC transactions need to
pass the flushable submission check.
In this patch, the following flags are implemented:
1. EC_FLAGS_EVENT_ENABLED: this is derived from the old
EC_FLAGS_QUERY_PENDING flag which can block SCI_EVT handlings.
With this flag, the logics implemented by the original flag are
extended:
1. Old logic: unless both of the flags are set, the event poller will
not be scheduled, and
2. New logic: as soon as both of the flags are set, the evet poller will
be scheduled.
2. EC_FLAGS_EVENT_DETECTED: this is also derived from the old
EC_FLAGS_QUERY_PENDING flag which can block SCI_EVT detection. It thus
can be used to indicate the storming prevention period for query
submission.
acpi_ec_submit_request()/acpi_ec_complete_request() are invoked to
implement this period so that acpi_set_gpe() can be invoked under the
"reference count > 0" condition.
3. EC_FLAGS_EVENT_PENDING: this is newly added to indicate the grace period
for event flushing (query flushing for now).
acpi_ec_submit_request()/acpi_ec_complete_request() are invoked to
implement this period so that the flushing process can wait until the
event handling (query transaction for now) to be completed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch refines EC command storm prevention support.
Current command storming code is wrong, when the storming condition is
detected, it only flags the condition without doing anything for the
current command but performing storming prevention for the follow-up
commands. So:
1. The first command which suffers from the storming still suffers from
storming.
2. The follow-up commands which may not suffer from the storming are
unconditionally forced into the storming prevention mode.
Ideally, we should only enable storm prevention immediately after detection
for the current command so that the next command can try the
power/performance efficient interrupt mode again.
This patch improves the command storm prevention by disabling GPE right
after the detection and re-enabling it right before completing the command
transaction using the GPE storming prevention APIs. This thus deploys the
following GPE handling model:
1. acpi_enable_gpe()/acpi_disable_gpe() for reference count changes:
This set of APIs are used for EC usage reference counting.
2. acpi_set_gpe(ACPI_GPE_ENABLE)/acpi_set_gpe(ACPI_GPE_DISABLE):
This set of APIs are used for preventing GPE storm. They must be invoked
when the reference count > 0.
Note that as the storming prevention should always happen when there is
an outstanding request, or GPE enabling value will be messed up by the
races. This patch also adds BUG_ON() to enforces this rule to prevent
future bugs.
The msleep(1) used after completing a transaction is useless now as this
sounds like a guard time only useful for platforms that need the
EC_FLAGS_MSI quirks while we have fixed GPE race issues using the previous
raw handler mode enabling. It is kept to avoid regressions. A seperate
patch which deletes EC_FLAGS_MSI quirks should take care of deleting it.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng