Add support for custom fan curves found on some ASUS ROG laptops.
These laptops have the ability to set a custom curve for the CPU
and GPU fans via two ACPI methods.
This patch adds two pwm<N> attributes to the hwmon sysfs,
pwm1 for CPU fan, pwm2 for GPU fan. Both are under the hwmon of the
name `asus_custom_fan_curve`. There is no safety check of the set
fan curves - this must be done in userspace.
The fans have settings [1,2,3] under pwm<N>_enable:
1. Enable and write settings out
2. Disable and use factory fan mode
3. Same as 2, additionally restoring default factory curve.
Use of 2 means that the curve the user has set is still stored and
won't be erased, but the laptop will be using its default auto-fan
mode. Re-enabling the manual mode then activates the curves again.
Notes:
- pwm<N>_enable = 0 is an invalid setting.
- pwm is actually a percentage and is scaled on writing to device.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20211024033705.5595-2-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The X13 Flow laptops can utilise an external GPU. This requires
toggling an ACPI method which will first disable the internal
dGPU, and then enable the eGPU.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20210807023656.25020-4-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In Windows the ASUS Armory Crate program can enable or disable the
dGPU via a WMI call. This functions much the same as various Linux
methods in software where the dGPU is removed from the device tree.
However the WMI call saves the state of dGPU (enabled or not) and
this then changes the dGPU visibility in Linux with no way for
Linux users to re-enable it. We expose the WMI method so users can
see and change the dGPU ACPI state.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20210807023656.25020-3-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some ASUS ROG laptops have the ability to drive the display panel
a higher rate to eliminate or reduce ghosting.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20210807023656.25020-2-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The UX360CA has a WMI device id 0x00060062, which reports whether the
lid is flipped in tablet mode (1) or in normal laptop mode (0).
Add a quirk (quirk_asus_use_lid_flip_devid) for devices on which this
WMI device should be used to figure out the SW_TABLET_MODE state, as
opposed to the quirk_asus_use_kbd_dock_devid.
Additionally, the device needs to be queried on resume and restore
because the firmware does not generate an event if the laptop is put to
sleep while in tablet mode, flipped to normal mode, and later awoken.
It is assumed other UX360* models have the same WMI device. As such, the
quirk is applied to devices with DMI_MATCH(DMI_PRODUCT_NAME, "UX360").
More devices with this feature need to be tested and added accordingly.
The reason for using an allowlist via the quirk mechanism is that the new
WMI device (0x00060062) is also present on some models which do not have
a 360 degree hinge (at least FX503VD and GL503VD from Hans' DSTS
collection) and therefore its presence cannot be relied on.
Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201020220944.1075530-1-samuel@cavoj.net
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On Asus 2-in-1s with a detachable keyboard the Asus WMI interface
reports if the tablet is attached to the keyboard or not.
Report if the 2-in-1 is in tablet or clamshell mode to userspace
by reporting SW_TABLET_MODE events to userspace.
This has been tested on a T100TA, T100CHI, T100HA and T200TA.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Throttle thermal policy ACPI device is used to control CPU cooling and
throttling. This patch adds sysfs entry for setting current mode and
Fn+F5 hotkey that switches to next.
Policy modes:
* 0x00 - default
* 0x01 - overboost
* 0x02 - silent
Signed-off-by: Leonid Maksymchuk <leonmaxx@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The device is officially called "Relative state of charge" (RSOC).
At the same time add the missing DEVID from the name.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At the same time add a comment explaining what it is used for.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Most newer ASUS laptops supports limiting the battery charge level, which
help prolonging the battery life.
Tested on a Zenbook UX430UNR.
Signed-off-by: Kristian Klausen <kristian@klausen.dk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Previously, asus-wmi was using the AGFN interface and FAN_CTRL device
for CPU fan control. However, this code has been found to be not fully
working on some recent products, and having checked the spec, these
interfaces are marked as being removed from future products currently
in development.
The replacement appears to be the CPU_FAN device, added in spec version
8.3 (March 2014) and present on many modern Asus laptops.
Add support for this device, and use it whenever it is detected.
The older approach based on AGFN and FAN_CTRL is used as a fallback
on products that do not have such device.
Other than switching between automatic and full speed, there is
no fan speed control through this new interface.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The asus-wmi driver currently uses the "AGFN" interface and
the FAN_CTRL device for fan control. According to the spec, this
interface is very dated and marked as pending removal from products
currently in development.
Clean up the way that the AGFN fan is detected and handled, also
preparing the driver for the introduction of an alternate fan
control method needed to support recent Asus products.
Not anticipating further development of this interface, simplify
the code by dropping any notion of being able to control multiple
AGFN fans (this was already limited to just a single fan through only
exposing a single fan in sysfs).
Check for the presence of AGFN fans at probe time, simplifying the code
flow in asus_hwmon_sysfs_is_visible().
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Asus WMI spec indicates that the function being controlled here
is called "Fan Boost Mode". The user-facing documentation also calls it
this.
The spec uses the term "fan mode" is used to refer to other things,
including functionality expected to appear on future products.
We missed this before as we are not dealing with the most readable of
specs, and didn't forsee any confusion around shortening the name.
Rename "fan mode" to "fan boost mode" to improve consistency with the
spec and to avoid a future naming conflict.
There is no interface breakage here since this has yet to be included
in an official kernel release. I also updated the kernel version listed
under ABI accordingly.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Yurii Pavlovskyi <yurii.pavlovskyi@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The WMI exposes a write-only device ID where up to three fan modes can be
switched on some laptops (TUF Gaming FX505GM). There is a hotkey
combination Fn-F5 that does have a fan icon, which is designed to toggle
between fan modes. The DSTS of the device ID returns information about the
presence of this capability and the presence of each of the two additional
fan modes as a bitmask (0x01 - overboost present, 0x02 - silent present)
[1].
Add a SysFS entry that reads the last written value and updates value in
WMI on write and a hotkey handler that toggles the modes taking into
account their availability according to DSTS.
Modes:
* 0x00 - normal or balanced,
* 0x01 - overboost, increased fan RPM,
* 0x02 - silent, decreased fan RPM
[1] Link: https://lkml.org/lkml/2019/4/12/110
Signed-off-by: Yurii Pavlovskyi <yurii.pavlovskyi@gmail.com>
Suggested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The DSTS method detection mistakenly selects DCTS instead of DSTS if
nothing is returned when the method ID is not defined in WMNB. As a result,
the control of keyboard backlight is not functional for TUF Gaming series
laptops. Implement detection based on _UID of the WMI device instead.
There is evidence that DCTS is handled by ACPI WMI devices that have _UID
ASUSWMI, whereas none of the devices without ASUSWMI respond to DCTS and
DSTS is used instead [1].
DSDT examples:
FX505GM (_UID ATK):
Method (WMNB, 3, Serialized)
{ ...
If ((Local0 == 0x53545344))
{
...
Return (Zero)
}
...
// No return
}
K54C (_UID ATK):
Method (WMNB, 3, Serialized)
{ ...
If ((Local0 == 0x53545344))
{
...
Return (0x02)
}
...
Return (0xFFFFFFFE)
}
[1] Link: https://lkml.org/lkml/2019/4/11/322
Signed-off-by: Yurii Pavlovskyi <yurii.pavlovskyi@gmail.com>
Suggested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some of latest ASUS laptops support new fn-lock mode switching.
This commit detect whether if the fn-lock option is enabled in
BIOS setting, and toggle the fn-lock mode via a new WMI DEVID
0x00100023 when the corresponding notify code captured.
The ASUS fn-lock mode switch is activated by pressing Fn+Esc.
When on, keys F1 to F12 behave as applicable, with meanings
defined by the application being used at the time. When off,
F1 to F12 directly triggers hardware features, well known audio
volume up/down, brightness up/down...etc, which were triggered
by holding down Fn key and F-keys.
Because there's no way to retrieve the fn-lock mode via existing
WMI methods per ASUS spec, driver need to initialize and keep the
fn-lock mode by itself.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Export asus_wmi_evaluate_method() and related headers for use by other
drivers.
hid-asus is going to use this to avoid advertising that it has a keyboard
backlight when the keyboard backlight is controlled via WMI.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Luke D. Jones