* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mount/1865 is trying to release lock (&lo->lo_ctl_mutex) at:
but there are no more locks to release!
mutex is already unlocked in loop_clr_fd(), we should not
try to unlock it in lo_release() again.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add a method for discovering the first memory BAR. All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The MSA2012 cannot inform the driver of configuration changes since all
management is out of band. This is a departure from any storage we have
supported in the past. We need some way to detect changes on the topology
so we implement this kernel thread. In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message. In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/linux-hdreg-h-cleanup:
remove <linux/ata.h> include from <linux/hdreg.h>
include/linux/hdreg.h: remove unused defines
isd200: use ATA_* defines instead of *_STAT and *_ERR ones
include/linux/hdreg.h: cover WIN_* and friends with #ifndef/#endif __KERNEL__
aoe: WIN_* -> ATA_CMD_*
isd200: WIN_* -> ATA_CMD_*
include/linux/hdreg.h: cover struct hd_driveid with #ifndef/#endif __KERNEL__
xsysace: make it 'struct hd_driveid'-free
ubd_kern: make it 'struct hd_driveid'-free
isd200: make it 'struct hd_driveid'-free
Trivial cleanups for nbd: only the return -EIO one really changes code,
and I've verified all the callers (plus 0 == success, 1 == error
convention is really ugly).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code was written to rely on big kernel lock to protect it from races.
It mostly works when interface is not abused.
So this uses tx_lock to protect data structures from concurrent use
between ioctl and worker threads.
Next step will be moving from ioctl to unlocked_ioctl.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: add missing return]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The missing device table means that the floppy module is not auto-loaded,
even when the appropriate PNP device (0700) is found.
We don't actually use the table in the module, since the device doesn't
have a struct pnp_driver, but it's sufficient to cause an alias in the
module that udev/modprobe will use.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Philippe De Muyter <phdm@macqel.be>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use ATA_CMD_* defines instead of WIN_* ones.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
Cc: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Change cf_id field in struct ace_device from 'struct hd_driveid *id'
to 'u16 *id' and update driver accordingly.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
While at it:
* Use ata_id_u32() macro.
There should be no functional changes caused by this patch.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: irq_node.handler() should return irqreturn_t
m68k: section mismatch fixes: Atari SCSI
m68k: section mismatch fixes: DMAsound for Atari
MAINTAINERS: Replace dead link to m68k CVS repository by link to new git repository
m68k: mac - Add SWIM floppy support
m68k: mac - Add a new entry in mac_model to identify the floppy controller type.
m68k: Add install target
* 'for-2.6.30' of git://git.kernel.dk/linux-2.6-block:
Get rid of pdflush_operation() in emergency sync and remount
btrfs: get rid of current_is_pdflush() in btrfs_btree_balance_dirty
Move the default_backing_dev_info out of readahead.c and into backing-dev.c
block: Repeated lines in switching-sched.txt
bsg: Remove bogus check against request_queue->max_sectors
block: WARN in __blk_put_request() for potential bio leak
loop: fix circular locking in loop_clr_fd()
loop: support barrier writes
bsg: add support for tail queuing
cpqarray: enable bus mastering
block: genhd.h cleanup patch
block: add private bio_set for bio integrity allocations
block: genhd.h comment needs updating
block: get rid of unused blkdev_free_rq() define
block: remove various blk_queue_*() setting functions in blk_init_queue_node()
cciss: add BUILD_BUG_ON() for catching bad CommandList_struct alignment
block: don't create bio_vec slabs of less than the inline number
block: cleanup bio_alloc_bioset()
It allows to read data from a floppy, but not to write to, and to eject the
floppy (useful on our Mac without eject button).
Signed-off-by: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (97 commits)
USB: qcserial: add device id for HP devices
USB: isp1760: Add a delay before reading the SKIPMAP registers in isp1760-hcd.c
USB: allow malformed LANGID descriptors
USB: pxa27x_udc: typo fixes and code cleanups
USB: gadget: gadget zero uses new suspend/resume hooks
USB: gadget: composite device-level suspend/resume hooks
USB: r8a66597-hcd: suspend/resume support
USB: more u32 conversion after transfer_buffer_length and actual_length
USB: Fix cp2101 USB serial device driver termios functions for console use
USB: CP2101 New Device ID
USB: ipaq: handle 4 endpoint devices
USB: S3C: Move usb-control.h to platform include
USB: ohci-hcd: Add ARCH_S3C24XX to the ohci-s3c2410.c glue
USB: pedantic: spelling correction in comment for ch9.h
USB: host: fix sparse warning: Using plain integer as NULL pointer
USB: ohci-s3c2410: fix name of bus clock
USB: ohci-s3c2410: remove <mach/hardware.h> include
USB: serial: rename cp2101 driver to cp210x
USB: CP2101 Reduce Error Logging
USB: CP2101 Support AN205 baud rates
...
With CONFIG_PROVE_LOCKING enabled
$ losetup /dev/loop0 file
$ losetup -o 32256 /dev/loop1 /dev/loop0
$ losetup -d /dev/loop1
$ losetup -d /dev/loop0
triggers a [ INFO: possible circular locking dependency detected ]
I think this warning is a false positive.
Open/close on a loop device acquires bd_mutex of the device before
acquiring lo_ctl_mutex of the same device. For ioctl(LOOP_CLR_FD) after
acquiring lo_ctl_mutex, fput on the backing_file might acquire the bd_mutex of
a device, if backing file is a device and this is the last reference to the
file being dropped . But it is guaranteed that it is impossible to have a
circular list of backing devices.(say loop2->loop1->loop0->loop2 is not
possible), which guarantees that this can never deadlock.
So this warning should be suppressed. It is very difficult to annotate lockdep
not to warn here in the correct way. A simple way to silence lockdep could be
to mark the lo_ctl_mutex in ioctl to be a sub class, but this might mask some
other real bugs.
@@ -1164,7 +1164,7 @@ static int lo_ioctl(struct block_device *bdev, fmode_t mode,
struct loop_device *lo = bdev->bd_disk->private_data;
int err;
- mutex_lock(&lo->lo_ctl_mutex);
+ mutex_lock_nested(&lo->lo_ctl_mutex, 1);
switch (cmd) {
case LOOP_SET_FD:
err = loop_set_fd(lo, mode, bdev, arg);
Or actually marking the bd_mutex after lo_ctl_mutex as a sub class could be
a better solution.
Luckily it is easy to avoid calling fput on backing file with lo_ctl_mutex
held, so no lockdep annotation is required.
If you do not like the special handling of the lo_ctl_mutex just for the
LOOP_CLR_FD ioctl in lo_ioctl(), the mutex handling could be moved inside
each of the individual ioctl handlers and I could send you another patch.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This helps the code look more consistent and cleaner.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1206) is the first step in converting usb-storage's
subdrivers into separate modules. It makes the following large-scale
changes:
Remove a bunch of unnecessary #ifdef's from usb_usual.h.
Not truly necessary, but it does clean things up.
Move the USB device-ID table (which is duplicated between
libusual and usb-storage) into its own source file,
usual-tables.c, and arrange for this to be linked with
either libusual or usb-storage according to whether
USB_LIBUSUAL is configured.
Add to usual-tables.c a new usb_usual_ignore_device()
function to detect whether a particular device needs to be
managed by a subdriver and not by the standard handlers
in usb-storage.
Export a whole bunch of functions in usb-storage, renaming
some of them because their names don't already begin with
"usb_stor_". These functions will be needed by the new
subdriver modules.
Split usb-storage's probe routine into two functions.
The subdrivers will call the probe1 routine, then fill in
their transport and protocol settings, and then call the
probe2 routine.
Take the default cases and error checking out of
get_transport() and get_protocol(), which run during
probe1, and instead put a check for invalid transport
or protocol values into the probe2 function.
Add a new probe routine to be used for standard devices,
i.e., those that don't need a subdriver. This new routine
checks whether the device should be ignored (because it
should be handled by ub or by a subdriver), and if not,
calls the probe1 and probe2 functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Honour barrier requests in the loop back block device driver.
In case of barrier bios, flush the backing file once before processing the
barrier and once after to guarantee ordering. In case of filesystems that
does not support fsync, barrier bios would be failed with -EOPNOTSUPP.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We've been carrying this patch for the last 3 years in Fedora,
long past time we got it upstream...
Call pci_set_master to enable bus-mastering if the BIOS hasn't
done it already.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The hardware requires 64-bit alignment of commands, so add a build bug
check for that. The recent commit 8a3173de4a
didn't change the size of the command, but other additions/changes may and
thus break badly at runtime.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
Upon a 'transfer error block' size is set to -EINVAL, but this becomes positive
since size is unsigned: p->offset still gets incremented.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 5e4c91c84b forgot to remove the
initial sleep, get rid of it.
Thanks to Randy Dunlap <randy.dunlap@oracle.com> for spotting this error.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When booting Xen Dom0 on a pre-release 3.2.1 hypervisor the system Oopses on a
"Unable to handle kernel NULL pointer dereference" in xenwatch.
From the backtrace it looks like backend_changed is calling bdget_disk
with a NULL pointer. Checking for NULL and returning ENODEV instead
allows the kernel to boot.
with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On occasion, the request will apparently have more segments than we
fit into the ring. Jens says:
> The second problem is that the block layer then appears to create one
> too many segments, but from the dump it has rq->nr_phys_segments ==
> BLKIF_MAX_SEGMENTS_PER_REQUEST. I suspect the latter is due to
> xen-blkfront not handling the merging on its own. It should check that
> the new page doesn't form part of the previous page. The
> rq_for_each_segment() iterates all single bits in the request, not dma
> segments. The "easiest" way to do this is to call blk_rq_map_sg() and
> then iterate the mapped sg list. That will give you what you are
> looking for.
> Here's a test patch, compiles but otherwise untested. I spent more
> time figuring out how to enable XEN than to code it up, so YMMV!
> Probably the sg list wants to be put inside the ring and only
> initialized on allocation, then you can get rid of the sg on stack and
> sg_init_table() loop call in the function. I'll leave that, and the
> testing, to you.
[Moved sg array into info structure, and initialize once. -J]
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed
This is caused by
| # define mfp ((*(volatile struct MFP*)MFP_BAS))
in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.
Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: fix deadlock in blk_abort_queue() for drivers that readd to timeout list
block: fix booting from partitioned md array
block: revert part of 18ce3751cc
cciss: PCI power management reset for kexec
paride/pg.c: xs(): &&/|| confusion
fs/bio: bio_alloc_bioset: pass right object ptr to mempool_free
block: fix bad definition of BIO_RW_SYNC
bsg: Fix sense buffer bug in SG_IO
The floppy driver requests an I/O port it doesn't need, and sometimes this
causes a conflict with a motherboard device reported by PNPBIOS.
This patch makes the floppy driver request and release only the ports it
actually uses. It also factors out the request/release stuff and the
io-ports list so they're all in one place now.
The current floppy driver uses only these ports:
0x3f2 (FD_DOR)
0x3f4 (FD_STATUS)
0x3f5 (FD_DATA)
0x3f7 (FD_DCR/FD_DIR)
but it requests 0x3f2-0x3f5 and 0x3f7, which includes the unused port
0x3f3.
Some BIOSes report 0x3f3 as a motherboard resource. The PNP system driver
reserves that, which causes a conflict when the floppy driver requests
0x3f2-0x3f5 later.
Philippe reported that this conflict broke the floppy driver between
2.6.11 and 2.6.22. His PNPBIOS reports these devices:
$ cat 00:07/id 00:07/resources # motherboard device
PNP0c02
state = active
io 0x80-0x80
io 0x10-0x1f
io 0x22-0x3f
io 0x44-0x5f
io 0x90-0x9f
io 0xa2-0xbf
io 0x3f0-0x3f1
io 0x3f3-0x3f3
$ cat 00:03/id 00:03/resources # floppy device
PNP0700
state = active
io 0x3f4-0x3f5
io 0x3f2-0x3f2
Reference:
http://lkml.org/lkml/2009/1/31/162
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Reported-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
Cc: Adam M Belay <abelay@mit.edu>
Cc: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Welland ME-747K-SI AoE target generates unsolicited AoE responses that
are marked as vendor extensions. Instead of ignoring these packets, the
aoe driver was generating kernel messages for each unrecognized response
received. This patch corrects the behavior.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Reported-by: <karaluh@karaluh.pl>
Tested-by: <karaluh@karaluh.pl>
Cc: <stable@kernel.org>
Cc: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kexec kernel resets the CCISS hardware in three steps:
1. Use PCI power management states to reset the controller in the
kexec kernel.
2. Clear the MSI/MSI-X bits in PCI configuration space so that MSI
initialization in the kexec kernel doesn't fail.
3. Use the CCISS "No-op" message to determine when the controller
firmware has recovered from the PCI PM reset.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix a problem that causes I/O to a disconnected (or partially initialized)
nbd device to hang indefinitely. To reproduce:
# ioctl NBD_SET_SIZE_BLOCKS /dev/nbd23 514048
# dd if=/dev/nbd23 of=/dev/null bs=4096 count=1
...hangs...
This can also occur when an nbd device loses its nbd-client/server
connection. Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.
This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277
Testing would need to be performed to determine if the two issues are the
same.
This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.
The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request. This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Reported-by: Jon Nelson <jnelson-kernel-bugzilla@jamponi.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two nbd-clients at same time are bad idea, and cause WARN_ON from nbd in
2.6.28-rc7 from sysfs_add_one. This simply prevents that from happening.
To reproduce:
cat /dev/zero | head -c 10000000 > /tmp/delme.fstest.fs
nbd-server 9100 -l /anyone.can.connect > /tmp/delme.fstest.fs &
sleep 1
nbd-client localhost 9100 /dev/nd0 &
nbd-client localhost 9100 /dev/nd0 &
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Apart from sleep_on() calls that could be easily converted to
wait_event() and completion calls amiflop also used a flag in ms_delay()
and ms_isr() as a custom mutex for ms_delay() without a need for
explicit unlocking. I converted that to a standard mutex.
The replacement for the unconditional sleep_on() in fd_motor_on() is a
complete_all() together with a INIT_COMPLETION() before the mod_timer()
call. It appears to me that fd_motor_on() might be called concurrently
and fd_select() does not guarantee mutual exclusivity in the case the
same drive gets selected again.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Acked-by: Jörg Dorchain <joerg@dorchain.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add "xlnx,sysace" compatible string to the of_platform binding
table. Platforms which have the SysACE chip on board (e.g.
Katmai) instead of via a Xilinx generated IP core will use
this value in their device tree.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Work around branch tracer warning.
sparc64: Fix unsigned long long warnings in drivers.
sparc64: Use unsigned long long for u64.
sparc: refactor code in fault_32.c
sparc64: refactor code in init_64.c
sparc64: refactor code in viohs.c
sparc: make proces_ver_nack a bit more readable
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix warnings caused by the unsigned long long usage in sparc
specific drivers.
The drivers were considered sparc specific more or less from the
filename alone.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: struct device - replace bus_id with dev_name()
lguest: move the initial guest page table creation code to the host
kvm-s390: implement config_changed for virtio on s390
virtio_console: support console resizing
virtio: add PCI device release() function
virtio_blk: fix type warning
virtio: block: dynamic maximum segments
virtio: set max_segment_size and max_sectors to infinite.
virtio: avoid implicit use of Linux page size in balloon interface
virtio: hand virtio ring alignment as argument to vring_new_virtqueue
virtio: use KVM_S390_VIRTIO_RING_ALIGN instead of relying on pagesize
virtio: use LGUEST_VRING_ALIGN instead of relying on pagesize
virtio: Don't use PAGE_SIZE for vring alignment in virtio_pci.
virtio: rename 'pagesize' arg to vring_init/vring_size
virtio: Don't use PAGE_SIZE in virtio_pci.c
virtio: struct device - replace bus_id with dev_name(), dev_set_name()
virtio-pci queue allocation not page-aligned
Fix parameter type warning:
linux-next-20081126/drivers/block/virtio_blk.c:307: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Enhance the driver to handle whatever maximum segment number the host
tells us to handle. Do to this, we need to allocate the scatterlist
dynamically.
We set max_phys_segments and max_hw_segments to the same value (1 if
the host doesn't tell us, since that's safest and all known hosts do
tell us).
Note that kmalloc'ing the structure for large sg_elems might be
problematic: the fix for this is sg_table, but that requires more
work.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Setting max_segment_size allows more than 64k per sg element, unless
the host specified a limit. Setting max_sectors indicates that our
max_hw_segments is the only limit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Simplify parameters to deregister_disk function.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In loop_unplug() function is expected that mapping is set
and lo->lo_backing_file is not NULL.
Unfortunately loop_set_fd() set the request queue unplug function,
but loop_clr_fd() doesn't clear that.
Loop device allows open of non-configured loop in some situations.
If the unplug on request queue is called, loop module oopses because
of missing lo_backing_file.
Simple reproducer:
losetup /dev/loop0 /xxx
losetup -d /dev/loop0
dmsetup create x --table "0 1 linear /dev/loop0 0"
EIP is at loop_unplug+0x1d/0x3b
...
Call Trace:
blk_unplug+0x57/0x5e
dm_table_unplug_all+0x34/0x77 [dm_mod]
destroy_inode+0x27/0x38
generic_delete_inode+0xd5/0xd9
iput+0x4b/0x4e
dm_resume+0xca/0xfe [dm_mod]
dev_suspend+0x143/0x165 [dm_mod]
dm_ctl_ioctl+0x18e/0x1cf [dm_mod]
dev_suspend+0x0/0x165 [dm_mod]
dm_ctl_ioctl+0x0/0x1cf [dm_mod]
vfs_ioctl+0x22/0x69
do_vfs_ioctl+0x39d/0x3c7
trace_hardirqs_on+0xb/0xd
remove_vma+0x50/0x56
do_munmap+0x21c/0x237
sys_ioctl+0x2c/0x45
sysenter_do_call+0x12/0x31
Several reports here
http://www.kerneloops.org/search.php?search=loop_unplug
Fix it by simply clear unplug function together with
removing of backing file.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When there are still queued bios and reference count
drops to zero, loop device must flush all queued bios.
Otherwise it can lead to situation that caller
closes the device, but some bios are still running
and endio() function call later OOpses when uses
unallocated mempool.
This happens for example when running dm-crypt over loop,
here is typical oops backtrace:
Oops: 0000 [#1] PREEMPT SMP
EIP is at mempool_free+0x12/0x6b
...
crypt_dec_pending+0x50/0x54 [dm_crypt]
crypt_endio+0x9f/0xa7 [dm_crypt]
crypt_endio+0x0/0xa7 [dm_crypt]
bio_endio+0x2b/0x2e
loop_thread+0x37a/0x3b1
do_lo_send_aops+0x0/0x165
autoremove_wake_function+0x0/0x33
loop_thread+0x0/0x3b1
kthread+0x3b/0x61
kthread+0x0/0x61
kernel_thread_helper+0x7/0x10
(But crash is reproducible with different dm targets
running over loop device too.)
Patch fixes it by flushing the bios in release call,
reusing the flush mechanism for switching backing store.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This both cleans up the code and also helps detect the spurious case
of a command attempted being removed from a queue it doesn't belong
to.
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Xen's blkfront sets noop as the default I/O scheduler at initialization
time to avoid elevator overheads such as idling, but with the advent of
basic disk profiling capabilities this is not necessary anymore. We
should just tell the block layer that we are a paravirt front-end driver
and the elevator will automatically make the necessary adjustments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As a paravirt front-end driver, virtio_blk is not a rotational device so
we want do avoid idling in AS/CFQ. Tell the block layer about this.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The pktcdvd created class devices only export some sysfs files,
but have no char dev_t registered in the driver.
At class device creation time they copy the dev_t value of the
block device to the char device, wich will register a new char
device in the driver core and userspace, with a conflicting dev_t
value.
In many cases the class devices dev_t just points to a random
USB device. This fixes the sysfs "duplicate entry" errors.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
final close of ->bdev should match the initial open, i.e.
get FMODE_READ | FMODE_NDELAY; FMODE_READ|FMODE_WRITE has
been a braino.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
Add %pm to omit the colons when printing a mac address.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should release old elevator when change to use a new one.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
This patch is a bug fix to the SystemACE driver to use resource_size_t
for physical address instead of unsigned long. This makes the driver
work correctly on 32 bit systems with 64-bit resources (e.g. PowerPC 440).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: James Morris <jmorris@namei.org>
Due to recent changes to usb_reset_device, the following hang occurs:
events/0 D 0000000000000000 0 6 2
ffff880037477cc0 0000000000000046 ffff880037477c50 ffffffff80237434
ffffffff80574c80 00000001000a015c 0000000000000286 ffff8800374757d0
ffff88002a31c860 ffff880037475a00 0000000036779140 ffff880037475a00
Call Trace:
[<ffffffff80237434>] try_to_del_timer_sync+0x52/0x5b
[<ffffffff8026f86c>] dma_pool_free+0x1a7/0x1ec
[<ffffffffa02a928a>] ub_disconnect+0x8e/0x1ad [ub]
[<ffffffff802407c9>] autoremove_wake_function+0x0/0x2e
[<ffffffff80378959>] usb_unbind_interface+0x5c/0xb7
[<ffffffff8036ab70>] __device_release_driver+0x95/0xbd
[<ffffffff8036ac70>] device_release_driver+0x21/0x2d
[<ffffffff803789f8>] usb_driver_release_interface+0x44/0x83
[<ffffffff80378ab9>] usb_forced_unbind_intf+0x17/0x1d
[<ffffffff80371ba4>] usb_reset_device+0x7d/0x114
[<ffffffffa02aaffd>] ub_reset_task+0x0/0x293 [ub]
[<ffffffffa02ab1c1>] ub_reset_task+0x1c4/0x293 [ub]
[<ffffffff8033dd1e>] flush_to_ldisc+0x0/0x1cd
[<ffffffffa02aaffd>] ub_reset_task+0x0/0x293 [ub]
[<ffffffff8023d302>] run_workqueue+0x87/0x114
[<ffffffff8023d467>] worker_thread+0xd8/0xe7
[<ffffffff802407c9>] autoremove_wake_function+0x0/0x2e
[<ffffffff8023d38f>] worker_thread+0x0/0xe7
[<ffffffff802404c1>] kthread+0x47/0x73
[<ffffffff8022c8dd>] schedule_tail+0x27/0x60
[<ffffffff8020c249>] child_rip+0xa/0x11
[<ffffffff8024047a>] kthread+0x0/0x73
[<ffffffff8020c23f>] child_rip+0x0/0x11
This is because usb_reset_device now unbinds, and that calls disconnect,
which in case of ub waits until the reset completes... which deadlocks.
Worse, this deadlocks keventd and this takes whole box down.
I'm going to fix this properly later, but let's unbreak the driver
quickly for non-composite devices at least.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This regression was introduced by commit
6ae5ce8e8d ("cciss: remove redundant code").
This patch fixes a regression where the controller firmware version is not
displayed in procfs. The previous patch would be called anytime something
changed. This will get called only once for each controller.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regression introduced by commit 6ae5ce8e8d
("cciss: remove redundant code").
This patch fixes a broken symlink in sysfs that was introduced by the
above commit. We broke it in 2.6.27-rc on or about 20080804. Some
installers are broken if this symlink does not exist and they may not
detect the logical drives configured on the controller. It does not
require being backported into 2.6.26.x or earlier kernels.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by Dick Gevers on Compaq ProLiant:
Oct 13 18:06:51 dvgcpl kernel: Compaq SMART2 Driver (v 2.6.0)
Oct 13 18:06:51 dvgcpl kernel: sys_init_module: 'cpqarray'->init
suspiciously returned 1, it should follow 0/-E convention
Oct 13 18:06:51 dvgcpl kernel: sys_init_module: loading module anyway...
Oct 13 18:06:51 dvgcpl kernel: Pid: 315, comm: modprobe Not tainted
2.6.27-desktop-0.rc8.2mnb #1
Oct 13 18:06:51 dvgcpl kernel: [<c0380612>] ? printk+0x18/0x1e
Oct 13 18:06:51 dvgcpl kernel: [<c0158f85>] sys_init_module+0x155/0x1c0
Oct 13 18:06:51 dvgcpl kernel: [<c0103f06>] syscall_call+0x7/0xb
Oct 13 18:06:51 dvgcpl kernel: =======================
Make it return 0 on success and -ENODEV if no array was found.
Reported-by: Dick Gevers <dvgevers@xs4all.nl>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 2 new SAS/SATA controllers.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing uses prepare_write or commit_write. Remove them from the tree
completely.
[akpm@linux-foundation.org: schedule simple_prepare_write() for unexporting]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
NB: nbd_ioctl() appears to be racy; BKL is held, but doesn't really
help, AFAICS. Left as-is for now, but it'll need fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Analog of blkdev_driver_ioctl() with sane arguments. For
now uses fake struct file, by the end of the series it won't
and blkdev_driver_ioctl() will become a wrapper around it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the Hades support that was marked as BROKEN 5 years ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges in:
x86/build, x86/microcode, x86/spinlocks, x86/memory-corruption-check,
x86/early-printk, x86/xsave, x86/quirks, x86/setup, x86/signal,
core/signal, x86/urgent, x86/xen
* 'x86-core-v2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (142 commits)
x86: make processor type select depend on CONFIG_EMBEDDED
x86: extend processor type select help text
x86, amd-iommu: propagate PCI device enabling error
warnings: fix arch/x86/kernel/io_apic_64.c
warnings: fix arch/x86/kernel/early_printk.c
x86, fpu: check __clear_user() return value
x86: memory corruption check - cleanup
x86: ioperm user_regset
xen: do not reserve 2 pages of padding between hypervisor and fixmap.
xen: use spin_lock_nest_lock when pinning a pagetable
x86: xsave: set FP, SSE bits in the xsave header in the user sigcontext
x86: xsave: fix error condition in save_i387_xstate()
x86: SB450: deprioritize DMI quirks
x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: replace a magic number with a named constant in the VESA boot code
x86 setup: remove IMAGE_OFFSET
x86 setup: remove DEF_INITSEG and DEF_SETUPSEG
Revert "x86: fix ghost EDD devices in /sys again"
x86 setup: fix ghost entries under /sys/firmware/edd take 3
x86: signal: remove indent in restore_sigcontext()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
* Use ATA_CMD_* defines instead of WIN_* ones.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since all bio_split calls refer the same single bio_split_pool, the bio_split
function can use bio_split_pool directly instead of the mempool_t parameter;
then the mempool_t parameter can be removed from bio_split param list, and
bio_split_pool is only referred in fs/bio.c file, can be marked static.
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts virtio_blk to use __blk_end_request() directly
so that end_{queued|dequeued}_request() can be removed.
Related 'uptodate' argument is converted to 'error'.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The current floppy_struct allows floppies to number sectors starting
from 0 or 1. This patch allows arbitrary first-sector numbers - for
example, 0xC1 for Amstrad CPC disks.
This extends the existing 1-bit field (FD_ZEROBASED, bit 2 of stretch)
to 8 bits (FD_SECTMASK, bits 2 to 9).
Currently 0x00 denotes a first sector number of 1, and 0x01 denotes a
first sector number of 0. We extend this by interpreting FD_SECTMASK
as the first sector number with the LSB flipped.
Signed-off-by: Keith Wansbrough <keith@lochan.org>
Cc: Alain Knaff <alain@linux.lu>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Karel Zak <kzak@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix cciss SCSI rescan code to better notice device changes.
If you hot-unplug a tape drive, then hot-plug a different
tape drive into the same slot in a storage enclosure,
the cciss driver wouldn't notice anything had changed, as
it was only looking at the LUN address and device type.
Now it looks at the inquiry page 0x83 device identifier,
and vendor and model strings as well.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Until recently, the maximum number of xvd block devices you could attach
to a Xen domU was 16. This limitation turned out to be problematic for
some users, so it was expanded to handle a much larger number of disks.
However, this requires a couple of changes in the way that blkfront
scans for disks. This functionality is already present in the Xen
linux-2.6.18-xen.hg tree; the attached patch adds this functionality to
the mainline xen-blkfront implementation. I successfully tested it on a
2.6.25 tree, and build tested it on 2.6.27-rc3.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move disk->capacity to part0->nr_sects and convert all users who
directly accessed the field to use {get|set}_capacity(). This is done
early to allow the __dev field to be moved.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
disk->part[] is protected by its matching bdev's lock. However,
non-critical accesses like collecting stats and printing out sysfs and
proc information used to be performed without any locking. As
partitions can come and go dynamically, partitions can go away
underneath those non-critical accesses. As some of those accesses are
writes, this theoretically can lead to silent corruption.
This patch fixes the race by using RCU for the partition array and dev
reference counter to hold partitions.
* Rename disk->part[] to disk->__part[] to make sure no one outside
genhd layer proper accesses it directly.
* Use RCU for disk->__part[] dereferencing.
* Implement disk_{get|put}_part() which can be used to get and put
partitions from gendisk respectively.
* Iterators are implemented to help iterate through all partitions
safely.
* Functions which require RCU readlock are marked with _rcu suffix.
* Use disk_put_part() in __blkdev_put() instead of directly putting
the contained kobject.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Implement disk_devt() and part_devt() and use them to directly
access devt instead of computing it from ->major and ->first_minor.
Note that all references to ->major and ->first_minor outside of
block layer is used to determine devt of the disk (the part0) and as
->major and ->first_minor will continue to represent devt for the
disk, converting these users aren't strictly necessary. However,
convert them for consistency.
* Implement disk_max_parts() to avoid directly deferencing
genhd->minors.
* Update bdget_disk() such that it doesn't assume consecutive minor
space.
* Move devt computation from register_disk() to add_disk() and make it
the only one (all other usages use the initially determined value).
These changes clean up the code and will help disk->part dereference
fix and extended block device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the following misc updates in preparation for
disk->part dereference fix and extended block devt support.
* implment part_to_disk()
* fix comment about gendisk->part indexing
* rename get_part() to disk_map_sector()
* don't use n which is always zero while printing disk information in
diskstats_show()
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
struct request has an ioprio member but it is never updated because
currently bios do not hold io context information. The implication of
this is that virtio_blk ends up passing useless information to the
backend driver.
That said, some IO schedulers such as CFQ do store io context
information in struct request, but use private members for that, which
means that that information cannot be directly accessed in a IO
scheduler-independent way.
This patch adds a function to obtain the ioprio of a request. We should
avoid accessing ioprio directly and use this function instead, so that
its users do not have to care about future changes in block layer
structures or what the currently active IO controller is.
This patch does not introduce any functional changes but paves the way
for future clean-ups and enhancements.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It was only used by ps3disk, and it should probably have been
REQ_TYPE_LINUX_BLOCK + REQ_LB_OP_FLUSH.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The variable statindex in send_request is never read, so remove it.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported by Thomas Graf.
If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.
Add __skb_unlink() call to fix that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This mirrors the of_device_id[] changes done in
fd098316ef ("sparc: Annotate
of_device_id arrays with const or __initdata.")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5b6155ee70, because
the block device ioctl's really aren't ready for it.
In particular, the "struct file *" and the "struct inode *" arguments do
not necessarily match, which means that the unlocked version of the
ioctl (that only gets a "struct file *") isn't actually able to handle
the cases it needs to handle.
This fixes bugzilla
http://bugzilla.kernel.org/show_bug.cgi?id=11401
Reported-and-bisected-by: Laurent Riffard <laurent.riffard@free.fr>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Alan Cox <alan@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of brd block device is "ramdisk", it's not "brd".
(The block device is registered by register_blkdev(RAMDISK_MAJOR, "ramdisk")
So it should be unregistered by unregister_blkdev(RAMDISK_MAJOR, "ramdisk")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We leak the memory allocated for the nbd_dev array at multiple places.
Fix them by either adding a kfree() or by rearranging code to return
before we allocate the memory.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are four operating modes Xen code may find itself running in:
- native
- hvm domain
- pv dom0
- pv domU
Clean up predicates for testing for these states to make them more consistent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes the needlessly global blkif_ioctl() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Bug fix. If SCSI tape support is turned off we get an implicit declaration
of cciss_unregister_scsi error in cciss_remove_one.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds support for multi-lun devices in a SAS environment. It's
required for the support of media changers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch changes way we notify the scsi layer that something has changed
on the SCSI tape side of the driver. The user can now just tell the driver
to rescan a particular controller rather than having to know the SCSI nexus
to echo into the SCSI mid-layer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes a problem where the logical volume count may go negative.
In some instances if several logical are configured on a controller and all
of them are deleted using the online utilities the volume count in /proc may
go negative with no way get it correct again.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes redundant code where ever logical volumes are added or
removed. It adds 3 new functions that are called instead of having the same
code spread throughout the driver. It also removes the cciss_getgeometry
function.
The patch is fairly complex but we haven't figured out how to make it any
simpler and still do everything that needs to be done. Some of the
complexity comes from having to special case booting from cciss. Otherwise
the gendisk doesn't get added in time and the switchroot will fail.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the rebuild_lun_table smart enough to not rip a logical
volume out from under the OS. Without this fix if a customer is running
hpacucli to monitor their storage the driver will blindly remove and re-add
the disks whenever the utility calls the CCISS_REGNEWD ioctl. Unfortunately,
both hpacucli and ACUXE call the ioctl repeatedly. Customers have reported
IO coming to a standstill. Calling the ioctl is the problem, this patch is
the fix.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Return -EFAULT instead of -ENOMEM if copy_from_user() fails.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
curr_queue is a local variable in a for loop, and it's being initialized
at the start of each loop. So any assignment at the end of the loop is
pointless.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATA over Ethernet: The semaphore emsgs_sema is used for signalling an
event, convert it in a completion.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently virtio_blk assumes a 512 byte hard sector size. This can cause
trouble / performance issues if the backing has a different block size
(like a file on an ext3 file system formatted with 4k block size or a dasd).
Lets add a feature flag that tells the guest to use a different hard sector
size than 512 byte.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code that needed this #include was removed one year ago.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Many people will see this option the first time now that it is in
drivers/block/
Make it clear that virtually noone needs it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch moves hd.c to drivers/block/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (80 commits)
ide-floppy: fix unfortunate function naming
ide-tape: unify idetape_create_read/write_cmd
ide: add ide_pc_intr() helper
ide-{floppy,scsi}: read Status Register before stopping DMA engine
ide-scsi: add more debugging to idescsi_pc_intr()
ide-scsi: use pc->callback
ide-floppy: add more debugging to idefloppy_pc_intr()
ide-tape: always log debug info in idetape_pc_intr() if debugging is enabled
ide-tape: add ide_tape_io_buffers() helper
ide-tape: factor out DSC handling from idetape_pc_intr()
ide-{floppy,tape}: move checking of ->failed_pc to ->callback
ide: add ide_issue_pc() helper
ide: add PC_FLAG_DRQ_INTERRUPT pc flag
ide-scsi: move idescsi_map_sg() call out from idescsi_issue_pc()
ide: add ide_transfer_pc() helper
ide-scsi: set drive->scsi flag for devices handled by the driver
ide-{cd,floppy,tape}: remove checking for drive->scsi
ide: add PC_FLAG_ZIP_DRIVE pc flag
ide-tape: factor out waiting for good ireason from idetape_transfer_pc()
ide-tape: set PC_FLAG_DMA_IN_PROGRESS flag in idetape_transfer_pc()
...
pd_special_command uses blk_put_request with struct request on the
stack. As a result, blk_put_request needs a hack to catch a NULL
request_queue. This converts pd_special_command to use
blk_execute_rq.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (37 commits)
splice: fix generic_file_splice_read() race with page invalidation
ramfs: enable splice write
drivers/block/pktcdvd.c: avoid useless memset
cdrom: revert commit 22a9189 (cdrom: use kmalloced buffers instead of buffers on stack)
scsi: sr avoids useless buffer allocation
block: blk_rq_map_kern uses the bounce buffers for stack buffers
block: add blk_queue_update_dma_pad
DAC960: push down BKL
pktcdvd: push BKL down into driver
paride: push ioctl down into driver
block: use get_unaligned_* helpers
block: extend queue_flag bitops
block: request_module(): use format string
Add bvec_merge_data to handle stacked devices and ->merge_bvec()
block: integrity flags can't use bit ops on unsigned short
cmdfilter: extend default read filter
sg: fix odd style (extra parenthesis) introduced by cmd filter patch
block: add bounce support to blk_rq_map_user_iov
cfq-iosched: get rid of enable_idle being unused warning
allow userspace to modify scsi command filter on per device basis
...
This patch changes the way we determine the maximum number of outstanding
commands for each controller.
Most Smart Array controllers can support up to 1024 commands, the notable
exceptions are the E200 and E200i.
The next generation of controllers which were just added support a mode of
operation called Zero Memory Raid (ZMR). In this mode they only support
64 outstanding commands. In Full Function Raid (FFR) mode they support
1024.
We have been setting the queue depth by arbitrarily assigning some value
for each controller. We needed a better way to set the queue depth to
avoid lots of annoying "fifo full" messages. So we made the driver a
little smarter. We now read the config table and subtract 4 from the
returned value. The -4 is to allow some room for ioctl calls which are
not tracked the same way as io commands are tracked.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression in cciss driver that if no logical drives are configured,
no device nodes at all get created.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid the 'memset(...,0, ...)' before calling 'init_cdrom_command' because
this function already does it.
Signed-off-by: Christophe Jaillet <jaillet.christophe@wanadoo.fr>
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Push the lock_kernel down into the driver and switch to unlocked_ioctl
[akpm@linux-foundation.org: build fix]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Leaves us with lock_kernel for two methods. Also remove a bogus printk
with no printk level and return -ENOTTY not -EINVAL for correctness.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
(Jens: added smp_lock.h include to pt.c, otherwise it wont compile because
of missing {un}lock_kernel() definition)
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When devices are stacked, one device's merge_bvec_fn may need to perform
the mapping and then call one or more functions for its underlying devices.
The following bio fields are used:
bio->bi_sector
bio->bi_bdev
bio->bi_size
bio->bi_rw using bio_data_dir()
This patch creates a new struct bvec_merge_data holding a copy of those
fields to avoid having to change them directly in the struct bio when
going down the stack only to have to change them back again on the way
back up. (And then when the bio gets mapped for real, the whole
exercise gets repeated, but that's a problem for another day...)
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Avoid allocations causing swap activity on the resume path by
preventing the allocations from doing IO and allowing them
to access the emergency pools.
These paths are used when a frontend device is trying to connect
to its backend driver over Xenbus. These reconnections are triggered
on demand by IO, so by definition there is already IO underway,
and further IO would naturally deadlock. On resume, this path
is triggered when the running system tries to continue using its
devices. If it cannot then the resume will fail; to try to avoid this
we let it dip into the emergency pools.
[ linux-2.6.18-xen changesets e8b49cfbdac, fdb998e79aba ]
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Return 0 instead of -EINVAL if the blkfront device is a cdrom,
i.e. had the VDISK_CDROM attribute. This allows udev's cdrom_id
to correctly detect the device as a cdrom device.
[ Add blkif_ioctl, and CDROMMULTISESSION ]
[ linux-2.6.18-xen changeset d2bd9af846b5 ]
Signed-off-by: Christian Limpach <Christian.Limpach@xensource.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add support for the next generation of HP Smart Array SAS/SATA
controllers. Shipping date is late Fall 2008.
Bump the driver version to 3.6.20 to reflect the new hardware support from
patch 1 of this set.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alias brd to rd in the hope of helping legacy users. Suggested by Jan.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hello Rusty,
sometimes it is useful to share a disk (e.g. usr). To avoid file system
corruption, the disk should be mounted read-only in that case. This patch
adds a new feature flag, that allows the host to specify, if the disk should
be considered read-only.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix a modprobe virtio_blk ; rmmod virtio_blk ; modprobe virtio_blk crash; this
was basically because we weren't doing "del_gendisk()" in the remove path.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (moved del_gendisk up)
In 2.6.25, ramdisk devices show up in /proc/partitions, which is a
behaviour change from the old rd.c. Add GENHD_FL_SUPPRESS_PARTITION_INFO,
which was present in rd.c.
All kernels prior to 2.6.25 weren't displaying ramdisks in
/proc/partitions. Since there are many userspace tools using information
from /proc/partitions some of them may now behave incorrectly (I didn't
tested any though). For example before 2.6.25 /proc/partitions was empty
if no block devices like hard disks and such were detected by kernel. Now
all 16 ramdisks are always visible there. Some software may rely on such
information (I mean, on empty /proc/partitions).
There was quite similar situation back in 2004, and ramdisks were excluded
back from displaying. Thats why I called this a regression (maybe a bit
unfortunate). See this patch for info:
http://kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.3-rc2/2.6.3-rc2-mm1/broken-out/nbd-proc-partitions-fix.patch
I also think that someone somewhere (long time ago) excluded ramdisks from
/proc/partitions for good reasons. It is possible that now such new
"feature" is harmless, but I think there are more chances that someone
will say "hey, /proc/partitions has changed, now my software doesn't work"
then "hey where did my new 2.6.25 feature go". nbd devices are also
excluded, maybe for very same (unknown to me) reasons.
Signed-off-by: Marcin Krol <hawk@pld-linux.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I don't use my IBM email address normally and people can find me in
CREDITS.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_part() is fairly expensive, as it O(N) loops over partitions
to find the right one. In lots of normal IO paths we end up looking
up the partition twice, to make matters even worse. Change the
stat add code to accept a passed in partition instead.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (32 commits)
USB GADGET/PERIPHERAL: g_file_storage Bulk-Only Transport compliance, clear-feature ignore
USB GADGET/PERIPHERAL: g_file_storage Bulk-Only Transport compliance
usb_serial: some coding style fixes
USB: Remove redundant dependencies on USB_ATM.
USB: UHCI: disable remote wakeup when it's not needed
USB: OHCI: work around bogus compiler warning
USB: add Cypress c67x00 OTG controller HCD driver
USB: add Cypress c67x00 OTG controller core driver
USB: add Cypress c67x00 low level interface code
USB: airprime: unlock mutex instead of trying to lock it again
USB: storage: Update mailling list address
USB: storage: UNUSUAL_DEVS() for PanDigital Picture frame.
USB: Add the USB 2.0 extension descriptor.
USB: add more FTDI device ids
USB: fix cannot work usb storage when using ohci-sm501
usb: gadget zero timer init fix
usb: gadget zero style fixups (mostly whitespace)
usb serial gadget: CDC ACM fixes
usb: pxa27x_udc driver
USB: INTOVA Pixtreme camera mass storage device
...
I hoped to continue to ignore this problem or use libusual, but these
days it's simpler to work around than to deal with it. Let's attempt to
use bad residue devices and hope that upper level integrity checks catch
any problems (e.g. please use sha1sum on your backups).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wodim says:
"close track/session scsi sendcmd: cmd timeout after 5.000 (480) s"
This happened because we ignored the supplied timeout and used 5s.
It's not completely correct to apply a timeout meant for the complete
command to any single URB, but we don't have many URBs per command, so
this is simple and works.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than faking up some geometry, allow the backend to push the disk
geometry via virtio pci config option. Keep the old geo code around for
compatibility.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified to single struct)
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API: in particular, we assume that feature
negotiation is complete once a driver's probe function returns.
There is nothing in the API to require this, however, and even I
didn't notice when it was violated.
So instead, we require the driver to specify what features it supports
in a table, we can then move the feature negotiation into the virtio
core. The intersection of device and driver features are presented in
a new 'features' bitmap in the struct virtio_device.
Note that this highlights the difference between Linux unsigned-long
bitmaps where each unsigned long is in native endian, and a
straight-forward little-endian array of bytes.
Drivers can still remove feature bits in their probe routine if they
really have to.
API changes:
- dev->config->feature() no longer gets and acks a feature.
- drivers should advertise their features in the 'feature_table' field
- use virtio_has_feature() for extra sanity when checking feature bits
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A recent proposed feature addition to the virtio block driver revealed
some flaws in the API, in particular how easy it is to break big
endian machines.
The virtio config space was originally chosen to be little-endian,
because we thought the config might be part of the PCI config space
for virtio_pci. It's actually a separate mmio region, so that
argument holds little water; as only x86 is currently using the virtio
mechanism, we can change this (but must do so now, before the
impending s390 merge).
API changes:
- __virtio_config_val() just becomes a striaght vdev->config_get() call.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Do not unregister the major at device remove, since there might be
another device instances around.
(qemu) pci_del 0 11
(qemu) ACPI: PCI interrupt for device 0000:00:0b.0 disabled
(qemu) pci_del 0 10
(qemu) ------------[ cut here ]------------
WARNING: at block/genhd.c:126 unregister_blkdev+0x74/0x9e()
ACPI: PCI interrupt for device 0000:00:0a.0 disabled
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Ron Minnich points out that a struct containing a char is not always
sizeof(char); simplest to remove the structure to avoid confusion.
Cc: "ron minnich" <rminnich@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds partition management for Block RAM Device (BRD).
This patch is done to keep in sync BRD and loop device drivers.
This patch adds a parameter to the module, max_part, to specify
the maximum number of partitions per RAM device.
Example:
# modprobe brd max_part=63
# ls -l /dev/ram*
brw-rw---- 1 root disk 1, 0 2008-04-03 13:39 /dev/ram0
brw-rw---- 1 root disk 1, 64 2008-04-03 13:39 /dev/ram1
brw-rw---- 1 root disk 1, 640 2008-04-03 13:39 /dev/ram10
brw-rw---- 1 root disk 1, 704 2008-04-03 13:39 /dev/ram11
brw-rw---- 1 root disk 1, 768 2008-04-03 13:39 /dev/ram12
brw-rw---- 1 root disk 1, 832 2008-04-03 13:39 /dev/ram13
brw-rw---- 1 root disk 1, 896 2008-04-03 13:39 /dev/ram14
brw-rw---- 1 root disk 1, 960 2008-04-03 13:39 /dev/ram15
brw-rw---- 1 root disk 1, 128 2008-04-03 13:39 /dev/ram2
brw-rw---- 1 root disk 1, 192 2008-04-03 13:39 /dev/ram3
brw-rw---- 1 root disk 1, 256 2008-04-03 13:39 /dev/ram4
brw-rw---- 1 root disk 1, 320 2008-04-03 13:39 /dev/ram5
brw-rw---- 1 root disk 1, 384 2008-04-03 13:39 /dev/ram6
brw-rw---- 1 root disk 1, 448 2008-04-03 13:39 /dev/ram7
brw-rw---- 1 root disk 1, 512 2008-04-03 13:39 /dev/ram8
brw-rw---- 1 root disk 1, 576 2008-04-03 13:39 /dev/ram9
# fdisk /dev/ram0
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
Command (m for help): o
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that, of course, the previous
content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-2, default 1): 1
Last cylinder or +size or +sizeM or +sizeK (1-2, default 2): 2
Command (m for help): w
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
# ls -l /dev/ram0*
brw-rw---- 1 root disk 1, 0 2008-04-03 13:40 /dev/ram0
brw-rw---- 1 root disk 1, 1 2008-04-03 13:40 /dev/ram0p1
# mkfs /dev/ram0p1
mke2fs 1.40-WIP (14-Nov-2006)
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
4016 inodes, 16032 blocks
801 blocks (5.00%) reserved for the super user
First data block=1
Maximum filesystem blocks=16515072
2 block groups
8192 blocks per group, 8192 fragments per group
2008 inodes per group
Superblock backups stored on blocks:
8193
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 26 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
# mount /dev/ram0p1 /mnt
df /mnt
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/ram0p1 15521 138 14582 1% /mnt
# ls -l /mnt
total 12
drwx------ 2 root root 12288 2008-04-03 13:41 lost+found
# umount /mnt
# rmmod brd
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Skip I/O merges when disabled
block: add large command support
block: replace sizeof(rq->cmd) with BLK_MAX_CDB
ide: use blk_rq_init() to initialize the request
block: use blk_rq_init() to initialize the request
block: rename and export rq_init()
block: no need to initialize rq->cmd with blk_get_request
block: no need to initialize rq->cmd in prepare_flush_fn hook
block/blk-barrier.c:blk_ordered_cur_seq() mustn't be inline
block/elevator.c:elv_rq_merge_ok() mustn't be inline
block: make queue flags non-atomic
block: add dma alignment and padding support to blk_rq_map_kern
unexport blk_max_pfn
ps3disk: Remove superfluous cast
block: make rq_init() do a full memset()
relay: fix splice problem
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the no longer used aoedev_isbusy().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Permit the use of partitions with network block devices (NBD).
A new parameter is introduced to define how many partition we want to be able
to manage per network block device. This parameter is "max_part".
For instance, to manage 63 partitions / loop device, we will do:
[on the server side]
# nbd-server 1234 /dev/sdb
[on the client side]
# modprobe nbd max_part=63
# ls -l /dev/nbd*
brw-rw---- 1 root disk 43, 0 2008-03-25 11:14 /dev/nbd0
brw-rw---- 1 root disk 43, 64 2008-03-25 11:11 /dev/nbd1
brw-rw---- 1 root disk 43, 640 2008-03-25 11:11 /dev/nbd10
brw-rw---- 1 root disk 43, 704 2008-03-25 11:11 /dev/nbd11
brw-rw---- 1 root disk 43, 768 2008-03-25 11:11 /dev/nbd12
brw-rw---- 1 root disk 43, 832 2008-03-25 11:11 /dev/nbd13
brw-rw---- 1 root disk 43, 896 2008-03-25 11:11 /dev/nbd14
brw-rw---- 1 root disk 43, 960 2008-03-25 11:11 /dev/nbd15
brw-rw---- 1 root disk 43, 128 2008-03-25 11:11 /dev/nbd2
brw-rw---- 1 root disk 43, 192 2008-03-25 11:11 /dev/nbd3
brw-rw---- 1 root disk 43, 256 2008-03-25 11:11 /dev/nbd4
brw-rw---- 1 root disk 43, 320 2008-03-25 11:11 /dev/nbd5
brw-rw---- 1 root disk 43, 384 2008-03-25 11:11 /dev/nbd6
brw-rw---- 1 root disk 43, 448 2008-03-25 11:11 /dev/nbd7
brw-rw---- 1 root disk 43, 512 2008-03-25 11:11 /dev/nbd8
brw-rw---- 1 root disk 43, 576 2008-03-25 11:11 /dev/nbd9
# nbd-client localhost 1234 /dev/nbd0
Negotiation: ..size = 80418240KB
bs=1024, sz=80418240
-------NOTE, RFC: partition table is not automatically read.
The driver sets bdev->bd_invalidated to 1 to force the read of the partition
table of the device, but this is done only on an open of the device.
So we have to do a "touch /dev/nbdX" or something like that.
It can't be done from the nbd-client or nbd driver because at this
level we can't ask to read the partition table and to serve the request
at the same time (-> deadlock)
If someone has a better idea, I'm open to any suggestion.
-------NOTE, RFC
# fdisk -l /dev/nbd0
Disk /dev/nbd0: 82.3 GB, 82348277760 bytes
255 heads, 63 sectors/track, 10011 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/nbd0p1 * 1 9965 80043831 83 Linux
/dev/nbd0p2 9966 10011 369495 5 Extended
/dev/nbd0p5 9966 10011 369463+ 82 Linux swap / Solaris
# ls -l /dev/nbd0*
brw-rw---- 1 root disk 43, 0 2008-03-25 11:16 /dev/nbd0
brw-rw---- 1 root disk 43, 1 2008-03-25 11:16 /dev/nbd0p1
brw-rw---- 1 root disk 43, 2 2008-03-25 11:16 /dev/nbd0p2
brw-rw---- 1 root disk 43, 5 2008-03-25 11:16 /dev/nbd0p5
# mount /dev/nbd0p1 /mnt
# ls /mnt
bin dev initrd lost+found opt sbin sys var
boot etc initrd.img media proc selinux tmp vmlinuz
cdrom home lib mnt root srv usr
# umount /mnt
# nbd-client -d /dev/nbd0
# ls -l /dev/nbd0*
brw-rw---- 1 root disk 43, 0 2008-03-25 11:16 /dev/nbd0
-------NOTE
On "nbd-client -d", we can do an iocl(BLKRRPART) to update partition table:
as the size of the device is 0, we don't have to serve the partition manager
request (-> no deadlock).
-------NOTE
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows Network Block Device to be mounted locally (nbd-client to
nbd-server over 127.0.0.1).
It creates a kthread to avoid the deadlock described in NBD tools
documentation. So, if nbd-client hangs waiting for pages, the kblockd thread
can continue its work and free pages.
I have tested the patch to verify that it avoids the hang that always occurs
when writing to a localhost nbd connection. I have also tested to verify that
no performance degradation results from the additional thread and queue.
Patch originally from Laurent Vivier.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use creation by full path: "driver/foo".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced between 2.6.25-rc2 and -rc3
drivers/block/xen-blkfront.c:139:5: warning: symbol 'blkif_getgeo' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace init_module and cleanup_module with static functions and
module_init/module_exit.
Signed-off-by: Jon Schindler <jkschind@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Any path needs to call it to initialize the request.
This is a preparation for large command support, which needs to
initialize the request in a proper way (that is, just doing a memset()
will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_get_request initializes rq->cmd (rq_init does) so the users don't
need to do that.
The purpose of this patch is to remove sizeof(rq->cmd) and &rq->cmd,
as a preparation for large command support, which changes rq->cmd from
the static array to a pointer. sizeof(rq->cmd) will not make sense and
&rq->cmd won't work.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer initializes rq->cmd (queue_flush calls rq_init) so
prepare_flush_fn hooks don't need to do that.
The purpose of this patch is to remove sizeof(rq->cmd), as a
preparation for large command support, which changes rq->cmd from the
static array to a pointer. sizeof(rq->cmd) will not make sense.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We can save some atomic ops in the IO path, if we clearly define
the rules of how to modify the queue flags.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As ps3disk is a ppc64-only driver, sector_t equals to unsigned long, and the
cast is not needed.
Reuse in another (possibly 32-bit) driver is protected by the safety net called
`compiler warning' (with the cast, it may silently truncate to 32-bit).
If sector_t ever changes, we will get a compiler warning as well (with the
cast, we won't).
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Alter the block device ->direct_access() API to work with the new
get_xip_mem() API (that requires both kaddr and pfn are returned).
Some architectures will not do the right thing in their virt_to_page() for use
by XIP (to translate from the kernel virtual address returned by
direct_access(), to a user mappable pfn in XIP's page fault handler.
However, we can't switch it to just return the pfn and not the kaddr, because
we have no good way to get a kva from a pfn, and XIP requires the kva for its
read(2) and write(2) handlers. So we have to return both.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-mm@kvack.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before getting merged, xen-blkfront was xenblk and
xen-netfront was xennet.
Temporarily adding compatibility module aliases
eases upgrades from older versions by e.g. allowing
mkinitrd to find the new version of the module.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add module aliases to support autoprobing modules
for xen frontend devices.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the xen block frontend driver is built as a module the module load
is only synchronous up to the point where the frontend and the backend
become connected rather than when the disk is added.
This means that there can be a race on boot between loading the module and
loading the dm-* modules and doing the scan for LVM physical volumes (all
in the initrd). In the failure case the disk is not present until after the
scan for physical volumes is complete.
Taken from:
http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/11483a00c017
Signed-off-by: Christian Limpach <Christian.Limpach@xensource.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
info->dev is never initialized to anything, so bdget(info->dev) is
meaningless. Get rid of info->dev, and use bdget_disk on the gendisk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Frontends are expected to write their protocol ABI to xenstore. Since
the protocol ABI defaults to the backend's native ABI, things work
fine without that as long as the frontend's native ABI is identical to
the backend's native ABI. This is not the case for xen-blkfront
running 32-on-64, because its ABI differs between 32 and 64 bit, and
thus needs this fix.
Based on http://xenbits.xensource.com/xen-unstable.hg?rev/c545932a18f3
and http://xenbits.xensource.com/xen-unstable.hg?rev/ffe52263b430 by
Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While looking at the implementation of the Ram backed block device
driver, I stumbled across a write-only local variable, which makes
little sense, so I assume it should actually work like this:
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
block: fix blk_register_queue() return value
block: fix memory hotplug and bouncing in block layer
block: replace remaining __FUNCTION__ occurrences
Kconfig: clean up block/Kconfig help descriptions
cciss: fix warning oops on rmmod of driver
cciss: Fix race between disk-adding code and interrupt handler
block: move the padding adjustment to blk_rq_map_sg
block: add bio_copy_user_iov support to blk_rq_map_user_iov
block: convert bio_copy_user to bio_copy_user_iov
loop: manage partitions in disk image
cdrom: use kmalloced buffers instead of buffers on stack
cdrom: make unregister_cdrom() return void
cdrom: use list_head for cdrom_device_info list
cdrom: protect cdrom_device_info list by mutex
cdrom: cleanup hardcoded error-code
cdrom: remove ifdef CONFIG_SYSCTL
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* Fix oops on cciss rmmod due to calling pci_free_consistent with
irqs disabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix race condition between cciss_init_one(), cciss_update_drive_info(),
and cciss_check_queues().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch allows to use loop device with partitionned disk image.
Original behavior of loop is not modified.
A new parameter is introduced to define how many partition we want to be
able to manage per loop device. This parameter is "max_part".
For instance, to manage 63 partitions / loop device, we will do:
# modprobe loop max_part=63
# ls -l /dev/loop?*
brw-rw---- 1 root disk 7, 0 2008-03-05 14:55 /dev/loop0
brw-rw---- 1 root disk 7, 64 2008-03-05 14:55 /dev/loop1
brw-rw---- 1 root disk 7, 128 2008-03-05 14:55 /dev/loop2
brw-rw---- 1 root disk 7, 192 2008-03-05 14:55 /dev/loop3
brw-rw---- 1 root disk 7, 256 2008-03-05 14:55 /dev/loop4
brw-rw---- 1 root disk 7, 320 2008-03-05 14:55 /dev/loop5
brw-rw---- 1 root disk 7, 384 2008-03-05 14:55 /dev/loop6
brw-rw---- 1 root disk 7, 448 2008-03-05 14:55 /dev/loop7
And to attach a raw partitionned disk image, the original losetup is used:
# losetup -f etch.img
# ls -l /dev/loop?*
brw-rw---- 1 root disk 7, 0 2008-03-05 14:55 /dev/loop0
brw-rw---- 1 root disk 7, 1 2008-03-05 14:57 /dev/loop0p1
brw-rw---- 1 root disk 7, 2 2008-03-05 14:57 /dev/loop0p2
brw-rw---- 1 root disk 7, 5 2008-03-05 14:57 /dev/loop0p5
brw-rw---- 1 root disk 7, 64 2008-03-05 14:55 /dev/loop1
brw-rw---- 1 root disk 7, 128 2008-03-05 14:55 /dev/loop2
brw-rw---- 1 root disk 7, 192 2008-03-05 14:55 /dev/loop3
brw-rw---- 1 root disk 7, 256 2008-03-05 14:55 /dev/loop4
brw-rw---- 1 root disk 7, 320 2008-03-05 14:55 /dev/loop5
brw-rw---- 1 root disk 7, 384 2008-03-05 14:55 /dev/loop6
brw-rw---- 1 root disk 7, 448 2008-03-05 14:55 /dev/loop7
# mount /dev/loop0p1 /mnt
# ls /mnt
bench cdrom home lib mnt root srv usr
bin dev initrd lost+found opt sbin sys var
boot etc initrd.img media proc selinux tmp vmlinuz
# umount /mnt
# losetup -d /dev/loop0
Of course, the same behavior can be done using kpartx on a loop device,
but modifying loop avoids to stack several layers of block device (loop +
device mapper), this is a very light modification (40% of modifications
are to manage the new parameter).
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch adds the missing include directive <linux/scatterlist.h> to the
cciss.c source file. This was discovered by our release team when building
the kernel for the Alpha architecture.
Errors were found as references to functions 'sg_init_table' and 'sg_page' do
not exist without the include for Alpha.
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When __blk_end_request returns nonzero, it means that the request was
not completely processed and some BIOs are still attached. Since we
have dequeued it by that time, it means leaking requests and hanging
processes, which is why BUG() was in there. In ub this happens if
a packet request ends normally, but with residue (e.g. when scsi_id
issues INQUIRY).
The fix is to make sure that arguments passed to __blk_end_request
are correct: the full request length and not just transferred length.
The transferred length is indicated to applications by adjusting
rq->data_len with old, unchanged code outside of this patch.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Cc: Greg KH <greg@kroah.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NBD does not protect the nbd_device's socket from becoming NULL during
receives.
This closes a race with the NBD_CLEAR_SOCK ioctl (nbd-client -d) setting
the nbd_device's socket to NULL right before NBD calls sock_xmit.
Signed-off-by: Mike Snitzer <snitzer@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.
The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
type t;
identifier f;
@@
- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)
@depends on haskernel@
type t;
identifier f;
@@
- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "unexport bio_{,un}map_user"
relay: fix subbuf_splice_actor() adding too many pages
The ps2esdi driver was marked as BROKEN more than two years ago due to being
Fix up so that the virtio_blk devices in sysfs link correctly to their
block device. This then allows them to be detected by hal, etc
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
no longer working for some time.
A driver that had been marked as BROKEN for such a long time seems to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still present in
the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Floppy rmmod locks up when no such hardware was initialized, since there is
nobody to wake the remove code up. Remove the completion, because release is
called during platform_unregister anyway.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The iSeries viodasd drivers does some very strange things with
scatterlists, one of these causing a BUG_ON to trigger when
scatterlist debugging is enabled due to initializing the
scatterlist with memset instead of sg_init_table().
This fixes it by using sg_init_table(). The rest of the stuff
it does to that poor list is still pretty awful but it will work.
I may look into fixing things in a nicer way some other time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On my system, pkt_open() consumes 584 bytes because the compiler decides to
inline lots of functions that would not normally be part of long call chains.
The following patch fixes that problem on my system.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: Nix <nix@esperi.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the #define READ_AHEAD 1024 from the driver and uses the
block layer defaults, instead. We have found that under certain workloads
the setting can cause a disk connected to the e200 controller to go offline.
If the disk hiccups the link may try to downshift but the controller is
never notified that the link successfully completed the renegotiation.
We've also found that performance using the block layer default of 32 pages
was on par with the 1024 setting. We tried setting it to zero at one time
based on info from our firmware guys but that killed performance. Turns out
we were talking about 2 different read ahead settings.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
volumes
This patch allows us to display information about all of the logical volumes
configured on a particular controller without stepping on memory even when
there are many volumes (128 or more) configured.
Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.
The two problems I have experienced with nbd and cfq are:
1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
fixed
There's a similar debian bug that has been filed as well:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638
There have been posts to nbd-general mailing list about problems with
cfq and nbd also.
2) nbd performs about 10% better (the last time I tested) with deadline
vs. cfq (the overhead of cfq doesn't provide much advantage to nbd [not
being a real disk], and you end up going through the I/O scheduler on
the nbd server anyway, so it makes sense that deadline is better with
nbd)
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below implements the getgeo hook for Xen block devices. Extracted
from the xen-unstable tree where it has been used for ages.
It is useful to have because it allows things like grub2 (used by the
Debian installer images) to work in a guest domain without having to
sprinkle Xen specific hacks around the place.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current pmac32_defconfig fails to build with the following error:
Building modules, stage 2.
ERROR: "check_media_bay" [drivers/block/swim3.ko] undefined!
WARNING: modpost: Found 23 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
make[2]: *** [__modpost] Error 1
This patch fixes that.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the arbitrary 128 device limit for NBD. nbds_max can now be set to
any number. In certain scenarios where devices are used sparsely we have
run into the 128 device limit.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I guess aoedev_init() can go away now.
Cc: Greg KH <greg@kroah.com>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the year in the copyright notices.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton pointed out that the "too many targets" message in patch 2 could
be printed for failing GFP_ATOMIC allocations. This patch makes the messages
more specific.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoedev aoeminor member doesn't need a long format.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An AoE target provides an estimate of the number of outstanding commands that
the AoE initiator can send before getting a response. The aoe_maxout
parameter provides a way to set an even lower limit. It will not allow a user
to use more outstanding commands than the target permits. If a user discovers
a problem with a large setting, this parameter provides a way for us to work
with them to debug the problem. We expect to improve the dynamic window
sizing algorithm and drop this parameter. For the time being, it is a
debugging aid.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An aoe driver user who had about 70 AoE targets found that he was hitting a
BUG in sysfs_create_file because the aoe driver was trying to tell the kernel
about an AoE device more than once. Each AoE device was reachable by several
local network interfaces, and multiple ATA device indentify responses were
returning from that single device.
This patch eliminates a race condition so that aoe always informs the block
layer of a new AoE device once in the presence of multiple incoming ATA device
identify responses.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
What this Patch Does
Even before this recent series of 12 patches to 2.6.22-rc4, the aoe
driver was reusing a small set of skbs that were allocated once and
were only used for outbound AoE commands.
The network layer cannot be allowed to put_page on the data that is
still associated with a bio we haven't returned to the block layer,
so the aoe driver (even before the patch under discussion) is still
the owner of skbs that have been handed to the network layer for
transmission. We need to keep track of these skbs so that we can
free them, but by tracking them, we can also easily re-use them.
The new patch was a response to the behavior of certain network
drivers. We cannot reuse an skb that the network driver still has
in its transmit ring. Network drivers can defer transmit ring
cleanup and then use the state in the skb to determine how many data
segments to clean up in its transmit ring. The tg3 driver is one
driver that behaves in this way.
When the network driver defers cleanup of its transmit ring, the aoe
driver can find itself in a situation where it would like to send an
AoE command, and the AoE target is ready for more work, but the
network driver still has all of the pre-allocated skbs. In that
case, the new patch just calls alloc_skb, as you'd expect.
We don't want to get carried away, though. We try not to do
excessive allocation in the write path, so we cap the number of skbs
we dynamically allocate.
Probably calling it a "dynamic pool" is misleading. We were already
trying to use a small fixed-size set of pre-allocated skbs before
this patch, and this patch just provides a little headroom (with a
ceiling, though) to accomodate network drivers that hang onto skbs,
by allocating when needed. The d->skbpool_hd list of allocated skbs
is necessary so that we can free them later.
We didn't notice the need for this headroom until AoE targets got
fast enough.
Alternatives
If the network layer never did a put_page on the pages in the bio's
we get from the block layer, then it would be possible for us to
hand skbs to the network layer and forget about them, allowing the
network layer to free skbs itself (and thereby calling our own
skb->destructor callback function if we needed that). In that case
we could get rid of the pre-allocated skbs and also the
d->skbpool_hd, instead just calling alloc_skb every time we wanted
to transmit a packet. The slab allocator would effectively maintain
the list of skbs.
Besides a loss of CPU cache locality, the main concern with that
approach the danger that it would increase the likelihood of
deadlock when VM is trying to free pages by writing dirty data from
the page cache through the aoe driver out to persistent storage on
an AoE device. Right now we have a situation where we have
pre-allocation that corresponds to how much we use, which seems
ideal.
Of course, there's still the separate issue of receiving the packets
that tell us that a write has successfully completed on the AoE
target. When memory is low and VM is using AoE to flush dirty data
to free up pages, it would be perfect if there were a way for us to
register a fast callback that could recognize write command
completion responses. But I don't think the current problems with
the receive side of the situation are a justification for
exacerbating the problem on the transmit side.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an AoE device is detected, the kernel is informed, and a new block device
is created. If the device is unused, the block device corresponding to remote
device that is no longer available may be removed from the system by telling
the aoe driver to "flush" its list of devices.
Without this patch, software like GPFS and LVM may attempt to read from AoE
devices that were discovered earlier but are no longer present, blocking until
the I/O attempt times out.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Richter suggested eliminating this goto.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By returning unsigned long long, mac_addr does not generate compiler warnings
on 64-bit architectures.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A remote AoE device is something can process ATA commands and is identified by
an AoE shelf number and an AoE slot number. Such a device might have more
than one network interface, and it might be reachable by more than one local
network interface. This patch tracks the available network paths available to
each AoE device, allowing them to be used more efficiently.
Andrew Morton asked about the call to msleep_interruptible in the revalidate
function. Yes, if a signal is pending, then msleep_interruptible will not
return 0. That means we will not loop but will call aoenet_xmit with a NULL
skb, which is a noop. If the system is too low on memory or the aoe driver is
too low on frames, then the user can hit control-C to interrupt the attempt to
do a revalidate. I have added a comment to the code summarizing that.
Andrew Morton asked whether the allocation performed inside addtgt could use a
more relaxed allocation like GFP_KERNEL, but addtgt is called when the aoedev
lock has been locked with spin_lock_irqsave. It would be nice to allocate the
memory under fewer restrictions, but targets are only added when the device is
being discovered, and if the target can't be added right now, we can try again
in a minute when then next AoE config query broadcast goes out.
Andrew Morton pointed out that the "too many targets" message could be printed
for failing GFP_ATOMIC allocations. The last patch in this series makes the
messages more specific.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support direct_access XIP method with brd.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a rewrite of the ramdisk block device driver.
The old one is really difficult because it effectively implements a block
device which serves data out of its own buffer cache. It relies on the dirty
bit being set, to pin its backing store in cache, however there are non
trivial paths which can clear the dirty bit (eg. try_to_free_buffers()),
which had recently lead to data corruption. And in general it is completely
wrong for a block device driver to do this.
The new one is more like a regular block device driver. It has no idea about
vm/vfs stuff. It's backing store is similar to the buffer cache (a simple
radix-tree of pages), but it doesn't know anything about page cache (the pages
in the radix tree are not pagecache pages).
There is one slight downside -- direct block device access and filesystem
metadata access goes through an extra copy and gets stored in RAM twice.
However, this downside is only slight, because the real buffercache of the
device is now reclaimable (because we're not playing crazy games with it), so
under memory intensive situations, footprint should effectively be the same --
maybe even a slight advantage to the new driver because it can also reclaim
buffer heads.
The fact that it now goes through all the regular vm/fs paths makes it
much more useful for testing, too.
text data bss dec hex filename
2837 849 384 4070 fe6 drivers/block/rd.o
3528 371 12 3911 f47 drivers/block/brd.o
Text is larger, but data and bss are smaller, making total size smaller.
A few other nice things about it:
- Similar structure and layout to the new loop device handlinag.
- Dynamic ramdisk creation.
- Runtime flexible buffer head size (because it is no longer part of the
ramdisk code).
- Boot / load time flexible ramdisk size, which could easily be extended
to a per-ramdisk runtime changeable size (eg. with an ioctl).
- Can use highmem for the backing store.
[akpm@linux-foundation.org: fix build]
[byron.bbradley@gmail.com: make rd_size non-static]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit edfaa7c365
Driver core: convert block from raw kobjects to core devices
This moves the block devices to /sys/class/block. It will create a
flat list of all block devices, with the disks and partitions in one
directory. For compatibility /sys/block is created and contains symlinks
to the disks.
introduced a global disk_type variable in <linux/genhd.h>, causing the
following compile error on Atari:
drivers/block/ataflop.c:93: error: conflicting types for 'disk_type'
include/linux/genhd.h:21: error: previous declaration of 'disk_type' was here
Rename the local disk_type variable in drivers/block/ataflop.c to
atari_disk_type, to avoid the conflict.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use upper_32_bits(x) macro to handle shifts that may be >= the width of
the data type.
drivers/block/cciss.c: In function 'do_cciss_request':
drivers/block/cciss.c:2655: warning: right shift count >= width of type
drivers/block/cciss.c:2656: warning: right shift count >= width of type
drivers/block/cciss.c:2657: warning: right shift count >= width of type
drivers/block/cciss.c:2658: warning: right shift count >= width of type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows a flag to be set on loop devices so that when they are
closed for the last time, they'll self-destruct.
In general, so that we can automatically allocate loop devices (as with
losetup -f) and have them disappear when we're done with them.
In particular, right now, so that we can stop relying on the hackish
special-case in umount(8) which kills off loop devices which were set up by
'mount -oloop'. That means we can stop putting crap in /etc/mtab which
doesn't belong there, which means it can be a symlink to /proc/mounts, which
means yet another writable file on the root filesystem is eliminated and the
'stateless' folks get happier... and OLPC trac #356 can be closed.
The mount(8) side of that is at
http://marc.info/?l=util-linux-ng&m=119362955431694&w=2
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Bernardo Innocenti <bernie@codewiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various instances of
if (!expr & mask)
which should probably have been
if (!(expr & mask))
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compile errors in the xilinxfb, xsysace and uartlite drivers used
by the Xilinx Virtex platform
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
Am Freitag, 1. Februar 2008 schrieb Christian Borntraeger:
> Right. I will fix that with an additional patch.
This patch goes on top of the minor number patch. Please let me know if
you want a merged patch:
Currently virtio_blk creates the disk name combinging "vd" with 'a'++.
This will give strange names after vdz. I have implemented names up to
vdzzz - inspired by the sd.c code. That should be sufficient for now.
There is one driver in the kernel (driver/s390/block/dasd_genhd.c) that
implements names from dasda-dasdzzzz allowing even more disks. Maybe
a janitor can come up with a common implementation usable for all kind
of block device drivers.
I have tested this patch with 100 disks - seems to work.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty,
currently virtio_blk uses one major number per device. While this works
quite well on most systems it is wasteful and will exhaust major numbers
on larger installations.
This patch allocates a major number on init and will use 16 minor numbers
for each disk. That will allow ~64k virtio_blk disks.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty,
I currently try to make my guest boot from an virtio root device
without having an external kernel. Some of the tools that I tried
expect HDIO_GETGEO to work. The most interesting value is likely
the geo.start value to get the offset of a partition. This value
is filled by block/ioctl.c if fops->getgeo is set. This patch also
fills in some standard values for heads, sectors and cylinders.
Makes sense?
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus Torvalds