The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:
echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Fixes: b493129482 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx23-olinuxino the LED turns on when level logic high is aplied to
GPIO2_1.
Fix the gpios property accordingly.
Fixes: b34aa18502 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tsadc is used to read cpu and gpu temperatures. Also enable it on the
other rk3288 boards beside the evb using the cru reset settings.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We defined bindings for the supply handling of act8846 regulators now, so
describe those on the firefly too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Specifying these rails should eventually let us do UHS.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the dts node for the PMU with the correct PMUIRQ interrupts
for each core.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is no crystal connected to the internal RTC on the Open Block
AX3. So let's disable it in order to prevent the kernel probing the
driver uselessly. Eventually this patches removes the following
warning message from the boot log:
"rtc-mv d0010300.rtc: internal RTC not ticking"
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8 +
On sun6i we already have PLL6 as AHB1 clock's parent. However this was
previously set in the dma controller node, which takes effect when the
dma controller is probed.
We want this to take effect as soon as possible, so hrtimer rate
calculation is correct, and to be sure the AHB1 clock rate remains as
stable as possible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock driver now supports a muxable ahb clock. Update the dtsi
with the proper compatible and add the new parent clocks.
This also adds the new pll6/4 output for pll6 on sun7i-a20. The
output is not used on sun4/5i.
Also use assigned-clocks to reparent ahb to pll6. We want ahb to
have a stable, non-changing clock rate. cpu/axi clock rate changes
as a result of newly added cpufreq support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU topology is unspecified for Ux500 but will be needed
for things like CoreSight. Let's just add it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Jesurun Q5 has a black plastic casing with the approximate dimensions
of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it
features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The
external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female
jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the
device has 1x red LED (hard wired to power) and an programmable green led.
On the board there is also an unpopulated IR receiver and the UART.
The devices is equipped with an AXP209 PMU.
For more details see: http://linux-sunxi.org/Jesurun_Q5
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the chipone-icn8318 touchscreen found on the Utoo P66 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi mini is a development board using the Allwinner A20 SoC,
with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI,
1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports,
ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pi_Minihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM,
microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A
ports, ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[hdegoede@redhat.com: Do not change soc node name, change compatible to
sun4i-a10-sram-controller to match the driver change]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13 / A10s has a few SRAM that can be mapped either to a device or to
the CPU, with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Since most of the time these SRAM won't be accessible by the CPU,
we can't use the mmio-sram driver and compatible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The eMMC on the A13 based Utoo-P66 tablet does not properly support hpi,
and trying to enable it results in the eMMC not working, so add a child-node
describing the eMMC, and set the broken-hpi property on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the a list compiled by Maxime Ripard,
which is based on A31 FEX files from the sunxi-boards repository. Not all
boards have the same settings. The settings in this patch are the ones
shared by A/B/C revisions, plus the default clock setting from u-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the unused usb1_vbus_pin_csq908 node (vbus is always on on the cs908),
and sort the remaining nodes alphabetically.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since the phy core already supports specifying a regulator to handle
during power up/down, it was decided to drop the regulator support
in the sun9i usb phy driver.
This patch switches the DT to the core bindings. This and the phy driver
would be in the same release and should not be a problem as far as DT
stability goes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has the architected timer, but the existing firmware from
Allwinner does not set CNTFRQ at all.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 SoC has the architected timer, but the existing firmware from
Allwinner does not set CNTFRQ at all.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The
WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO.
The IC also takes a power enable signal via GPIO. This is supported
with the new power sequencing bindings.
The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not enabled yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc1 is used to connect to the WiFi chip on the Hummingbird A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[maxime: Changed the drive and pull values for their defines]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Sometimes we need to specify non-probably information for sdio devices in the
devicetree, this is done through child nodes addressed by the reg property,
whereby the reg property refers to the sdio function number, see;
Documentation/devicetree/bindings/mmc/mmc.txt
This commit adds the necessary address- and size-cells properties to the mmc
controller nodes in the dtsi files, so that dts files needing such a child
node do not need to specify these themselves.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the AXP221 regulators. Only the ones directly used
on the board are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the
P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Hummingbird A31 has an AXP221 PMIC hooked up to the P2WI controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The p2wi controller has only one possible pinmux setting. Use it by
default in the dtsi, instead of having to set it in each board's dts.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: reformat commit title; rename p2wi pins and use as default]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.
[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add support for Wexler TAB7200 tablet.
The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The touchscreen controller in the A13 and later has a different temperature
curve than the one in the original A10, change the compatible for the A13 and
later so that the kernel will use the correct curve.
Reported-by: Tong Zhang <lovewilliam@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
lcd screen, 512MB RAM & 4GB emmc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The auxtek-t004:
http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
a 2 micro-usb receptacles, one for power and one for USB OTG.
The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add A13 mmc2 pinmux settings, note these are for a 8bit bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13 and the A10s use the same die (this has been confirmed by Allwinner),
as such there is no need to differentiate between the ehci/ohci parts of both,
the only reasons there were different allwinner,sun5i-a*-foo compatible
between these 2 parts is costemetically and because we could when we still
had 2 completely different dtsi files.
The allwinner,sun5i-a*-foo compatible strings are not used for binding at all,
the actual driver binds to the generic-?hci compatible, so we can safely remove
this cosmetical difference and simplify the dtsi files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the lradc controlled tablet keys on the Chuwi V7 CW0825 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM,
8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using
USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out,
a TRS connector for A/V, SPDIF and IrDA.
This patch adds basic support for the device, more information can
be found here (http://linux-sunxi.org/Mele_I7).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10s and the A13 are very similar SoCs, the only difference being the
number of pins and the number of devices available (number of UARTs, EMAC only
in the A10s, etc.), and the clocks and pinctrl functions obviously.
Create a common DTSI that will be included by the A10s and A13 DTSI, that will
add their SoC differences in there.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Optimus board, all three USB hosts can be used.
HCI0 and HCI2 are available through the USB connector.
HCI1 is available with HSIC through 2 pins on the GPIO
expansion header.
This patch also adds a regulator for HCI2/USB3's VBUS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zalan Blenessy <zalan.blenessy@gmail.com>
On sun9i, there are 3 independent usb phys for EHCI/OHCI.
Add device nodes for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB controller and phy clocks and resets have a separate address
block and driver. Add the nodes to represent them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Wills Wang <wills.wang.open@gmail.com>
Add support for the LinkSprite pcDuino 3 Nano board. This is a low-cost
Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM,
4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and
another for power in, HDMI, SATA, 5V power for SATA devices, gigabit
Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.
For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano
Changes in v3:
- rename LEDs to pcduino3-nano:green:usr[12]
- remove optional features on Arduino headers (i2c2, spi0, uart2)
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot,
miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and
3.5mm headphone jack.
Changes since v2:
* Fix syntax error (brown paper bag release)
Changes since v1:
* Added sun4i-lradc keymap
* Added TODO note about missing IRQ pins for bma250
* Fixed formatting issues and removed external URLs
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
DTSI first under a GPL/X11 dual-license. Hopefully, the DTS will follow soon.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Oliver Schinagl <oliver@schinagl.nl>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
DTSI first under a GPL/X11 dual-license. Hopefully, the DTS will follow soon.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Oliver Schinagl <oliver@schinagl.nl>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
MSIOF Base Address H'E6xx can be accessed by CPU and DMAC.
MSIOF Base Address H'E7xx for DMAC was removed from H/W manual.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSIOF Base Address H'E6xx can be accessed by CPU and DMAC.
MSIOF Base Address H'E7xx for DMAC was removed from H/W manual.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We were expecting to sit on this branch through most of the merge window since
the contents was merged into our tree late, but we ended up sitting on all of
our contents so it can go in with the rest.
The contents here is:
- A large branch of cleanups of the CM/PRM blocks on OMAP.
- A couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- A branch with DT updates for Freescale i.MX. including some shuffling from
.dts to .dtsi (include) files that causes a little churn.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ssbK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
Driver updates for v4.1. Some of these are for drivers/soc, where we find more
and more SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level interface
for talking to the system PMIC over a dedicated I2C interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used for CPU
up/down and needs to be in a shared location for arm/arm64 common code.
- Cleanup of ARM-CCI PMU code.
- Anoter set of cleanusp to the OMAP GPMC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/sWo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Our SoC branch usually contains expanded support for new SoCs and other core
platform code. In this case, that includes:
- Support for the new Annapurna Labs "Alpine" platform
- A rework greatly simplifying adding new platform support to the MCPM
subsystem (Multi-cluster power management)
- Cpuidle and PM improvements for Exynos3250
- Misc updates for Renesas, OMAP, Meson, i.MX. Some of these could have
gone in other branches but ended up here for various reasons.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzfWAAoJEIwa5zzehBx3idcP/Rt042tqb0bian/4M1Ud1aQ7
AMRd4oU5MfWAlzaGPeMBS+b1eo/eENj6wyWsvBQIByZN76ImlUXtxsx0U0frLrVg
mWVo9zOLRuoE6yyq329zZgg1IM1RtRIruS6zucKsHgKtq0DcjhYGGUH0ZVZk/rKI
RLtRK8U6Jr0lnpu1TDE5mii7GCCZlEl5dG+J3w5ewC9y7RLRlM09xjK/Zsj0QOqY
JvMOIaHuHMT6l7BQ6QajtVxTeGECOJ3YDqC6mDHCVD7f3v88+7H5C20xNGPK921w
tLfB5qOojnj+kKZRPhi8EGnRzKwrBq6/mE5CvvigTCGlAEUOzy7PFSY9oNE80QeL
6mUdPTuZuqz7ZEIF0kj8I0AkB6k8B+aYfqA9mqM5yGpa11HvZZGfP7CwI4izoe6+
sT++0OeDPwbsMyRxZjqNQLs4QYaKGYMP4NCgA17zz5ToRCQZy7e5hd2GYzaRouyi
kTpR9FbxwDcBIwTcA3F7oJ90BEMJ0tvGz/Al11UQpzPePhTwQt2yB5bRZyK/RYIU
x8k8RHArG3fmS89D4aOViL3sy/zoUBedx4UfAo6jVbrvoZGALQL23KHdqBqDiPmP
sMRj/sSr+0h9nJCVNM6I/OUD4/IrpFGaeX9V7rpEsHVe7j83eV7Q2wNRPyVTgxdn
jS8TS0FNAXIv8FO9EoNH
=tcGs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. In this case, that includes:
- support for the new Annapurna Labs "Alpine" platform
- a rework greatly simplifying adding new platform support to the
MCPM subsystem (Multi-cluster power management)
- cpuidle and PM improvements for Exynos3250
- misc updates for Renesas, OMAP, Meson, i.MX. Some of these could
have gone in other branches but ended up here for various reasons"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
ARM: alpine: add support for generic pci
ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: DCSCB: tighten CPU validity assertion
ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
ARM: MCPM: move the algorithmic complexity to the core code
ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
ARM: EXYNOS: add AFTR mode support for Exynos3250
ARM: EXYNOS: add code for setting/clearing boot flag
ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
ARM: EXYNOS: Remove left over 'extra_save'
ARM: EXYNOS: Constify exynos_pm_data array
ARM: EXYNOS: use static in suspend.c
ARM: EXYNOS: Use platform device name as power domain name
ARM: EXYNOS: add support for async-bridge clocks for pm_domains
ARM: omap-device: add missed callback for suspend-to-disk
...
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
Add the watchdog related entries to the Krait Processor Sub-system
(KPSS) timer IPQ8064 devicetree section. Also, add a fixed-clock
description of SLEEP_CLK, which will do for now.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Merge a set of fixes that we missed sending in before v4.0 release. These
will also be sent to -stable.
* fixes: (659 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
arm64: juno: Fix misleading name of UART reference clock
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: socfpga: dts: fix spi1 interrupt
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
As pointed out by Stephen Rothwell, commit e52117638b ("ARM: dts:
omap3: Add DT entries for OMAP 3 ISP") conflicts with b8845074cf
("ARM: dts: omap3: add minimal l4 bus layout with control module support")
in non-obvious ways, causing a build failure when both patches
are present.
This merges the two branches that introduce the respective changes
into the next/late branch to resolve the way that Stephen suggested,
as confirmed by Tony.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.org/lkml/2015/4/6/436
Acked-by: Tony Lindgren <tony@atomide.com>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlUsHXYACgkQMUfUDdst+ykGvwCfbI3z0VYJqyvPi7pbn+jtGouQ
E7MAoICdP90ofZfyzQzXy+2xKTTCiP5L
=jSjh
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver updates from Greg KH:
"Here's the big USB (and PHY) driver patchset for 4.1-rc1.
Everything here has been in linux-next, and the full details are below
in the shortlog. Nothing major, just the normal round of new
drivers,api updates, and other changes, mostly in the USB gadget area,
as usual"
* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
drivers/usb/core: devio.c: Removed an uneeded space before tab
usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
usb: chipidea: debug: add low power mode check before print registers
usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
usb: core: hub: use new USB_RESUME_TIMEOUT
usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
usb: host: sl811: use new USB_RESUME_TIMEOUT
usb: host: r8a66597: use new USB_RESUME_TIMEOUT
usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
usb: host: fusbh200: use new USB_RESUME_TIMEOUT
usb: host: fotg210: use new USB_RESUME_TIMEOUT
usb: host: isp116x: use new USB_RESUME_TIMEOUT
usb: musb: use new USB_RESUME_TIMEOUT
usb: host: uhci: use new USB_RESUME_TIMEOUT
usb: host: ehci: use new USB_RESUME_TIMEOUT
usb: host: xhci: use new USB_RESUME_TIMEOUT
usb: define a generic USB_RESUME_TIMEOUT macro
usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
ehci-hub: use USB_DT_HUB
...
- Convert GPC controller to use stacked interrupt domains
- Add power domain descriptions for i.MX6 platforms
- Improve i.MX25 pin function defines
- Disable PWM devices in <soc>.dtsi by default and enable it at board
level dts where the device is actually available.
- Define labels for SNVS RTC device to ease the board description,
where an external RTC is available.
- Add dr_mode host setting to all i.MX host-only USB instances
- Support Miscellaneous System Control Module (MSCM) for VF610
- Add initial i.MX6SL WaRP Board support
- Add i.MX6SX SDB revision B board support
- A bunch of imx28-apf28dev board updates, including gpio polarity
correction and CAN, AUART device support.
- SolidRun iMX6 platform updates: dual-license of GPLv2/X11, PWM
setup, PCF8523 RTC, GPIO key and SGTL5000 audio support.
- A number of random device additions for boards: SPI and CAN for
vf-colibri, MAX7310 GPIO expander for imx6qdl-sabreauto and LCD
support for imx25-pdk.
Note: Branch imx/cleanup was merged as the base to solve conflict on
imx25 iomux header. Branch imx/soc was merged as the base to solve
conflict on arch/arm/mach-imx/gpc.c. And Jason Cooper's irqchip/vybrid
branch was pulled into the base as a run-time dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVGUnPAAoJEFBXWFqHsHzOfU4H/2YtayumlbwhySiP7pAD0fty
qmAUgJqZxvfS+Sxo1qnm5FEQrNS0bMswB1htWLKEJuPEe9kf+/iDw7g4SWXx3Ul0
W2Lkk5jJl32P+SWCg+8BQKk46Tp3FASOeiA4TTCcQmjFJ9h6W5z/cY8zaEH/J7eH
QRFC62A8NCvS3rlnyGumCpBtcDnWNV/LwSmGMtPOAmFrMmXpZOKRCArA3AoP50ml
L6wPI+ZYGnn4PimwX9Fea5mBgecNdLiTEziBQYTsqeiE8vtU5AAqnmjYXEwAvM/f
MeCxBcdDzwrsa5z/WfpOVw1ERMokMSBjJ/nYkRHIgMzDwRYTYW+M69mOIpyy+iM=
=gKJl
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/late
Pull "The i.MX device tree updates for 4.1" from Shawn Guo:
- Convert GPC controller to use stacked interrupt domains
- Add power domain descriptions for i.MX6 platforms
- Improve i.MX25 pin function defines
- Disable PWM devices in <soc>.dtsi by default and enable it at board
level dts where the device is actually available.
- Define labels for SNVS RTC device to ease the board description,
where an external RTC is available.
- Add dr_mode host setting to all i.MX host-only USB instances
- Support Miscellaneous System Control Module (MSCM) for VF610
- Add initial i.MX6SL WaRP Board support
- Add i.MX6SX SDB revision B board support
- A bunch of imx28-apf28dev board updates, including gpio polarity
correction and CAN, AUART device support.
- SolidRun iMX6 platform updates: dual-license of GPLv2/X11, PWM
setup, PCF8523 RTC, GPIO key and SGTL5000 audio support.
- A number of random device additions for boards: SPI and CAN for
vf-colibri, MAX7310 GPIO expander for imx6qdl-sabreauto and LCD
support for imx25-pdk.
Note: Branch imx/cleanup was merged as the base to solve conflict on
imx25 iomux header. Branch imx/soc was merged as the base to solve
conflict on arch/arm/mach-imx/gpc.c. And Jason Cooper's irqchip/vybrid
branch was pulled into the base as a run-time dependency.
* tag 'imx-dt-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (69 commits)
ARM: dts: hummingboard: add sgtl5000 support for Hummingboard Pro
ARM: dts: imx25-pinfunc: Add several pinfunctions
ARM: dts: vf610: fix missing irqs
ARM: dts: cubox: Map gpio-keys to gpio3 8
ARM: dts: hummingboard: Setup pwm lines
ARM: dts: hummingboard: enable PCF8523 RTC support
ARM: dts: Re-license SolidRun iMX6 platform DT GPL v2/X11
ARM: dts: imx28: add alternative pinmuxing for spi3
ARM: dts: imx6sx: Add label snvs_rtc
ARM: dts: imx6sl: Add label snvs_rtc
ARM: imx6: Warn when an old DT is detected
ARM: imx6: Allow GPC interrupts affinity to be changed
ARM: imx6qdl-sabreauto.dtsi: add max7310 support
ARM: dts: imx6sl-warp: Add BCM4330 support
ARM: dts: imx28-apf28dev: add wakeup function to user button
ARM: dts: imx28-apf28dev: fix user button polarity
ARM: dts: imx25-pinfunc: remove input values for pinfuncs without input register
ARM: dts: vf610: add Miscellaneous System Control Module (MSCM)
ARM: dts: imx6sl-warp: Pass 'bus-width' property
ARM: dts: imx6qdl: disable PWMs by default
...
This patch adds device-tree entry for the internal pci bus on Alpine.
Alpine's on-chip devices appear as pci devices on this bus.
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
from Tero Kristo <t-kristo@ti.com>.
This sets gets us into a better position for further clean-up:
- Gets PRCM code closer to being device drivers
- Allows to move the remainig clock code to drivers/clk for v4.2
- Starts enforcing interconnect hierarchy in the SoC specific .dts
files to enforce device drivers are only accesing registers in
the related hardware module
This patchset has seen quite a few revisions but did not come into
mergeable shape until recently. As other patchsets for clock specific
device drivers depend on this, it would be good to get this merged
although it's a bit late for the v4.1 merge window.
Note that as the device entries in the .dts files are moved around,
this is based on earlier non-urgent fixes to avoid a non-trivial
merge conflict.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jiqd
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/prcm-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late
Pull "Clean-up for omap PRCM (Power Reset Clock Management) and interconnects" from Tony Lindgren
Patches originally from Tero Kristo <t-kristo@ti.com>.
This sets gets us into a better position for further clean-up:
- Gets PRCM code closer to being device drivers
- Allows to move the remainig clock code to drivers/clk for v4.2
- Starts enforcing interconnect hierarchy in the SoC specific .dts
files to enforce device drivers are only accesing registers in
the related hardware module
This patchset has seen quite a few revisions but did not come into
mergeable shape until recently. As other patchsets for clock specific
device drivers depend on this, it would be good to get this merged
although it's a bit late for the v4.1 merge window.
Note that as the device entries in the .dts files are moved around,
this is based on earlier non-urgent fixes to avoid a non-trivial
merge conflict.
* tag 'omap-for-v4.1/prcm-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (44 commits)
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
ARM: OMAP2+: PRM: move SoC specific init calls within a generic API
...
use 0xf1000000 as internal registers on Armada 370 DB: needed for the
recent version of the board which no more comes with a bogus version of
the Armada 370 SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlUnaLQACgkQCwYYjhRyO9WMIwCfSlT0IQHw0PGHoXO7AW+hByyJ
THQAn0eCblJ3eHmBQqaeo/ftVc/xxZju
=G5cB
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.0-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu fix for 4.0" from Gregory CLEMENT:
use 0xf1000000 as internal registers on Armada 370 DB: needed for the
recent version of the board which no more comes with a bogus version of
the Armada 370 SoC.
* tag 'mvebu-fixes-4.0-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: mvebu: Disable CPU Idle on Armada 38x
This reverts commit e6f219b8ec.
to fix a build error:
arch/arm/boot/dts/mt8135-pinfunc.h:18:40: fatal error: dt-bindings/pinctrl/mt65xx.h: No such file or directory
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IPgJ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-core-4.1-3' of git://git.infradead.org/users/jcooper/linux into irq/core
irqchip core change for v4.1 (round 3) from Jason Cooper
Purge the gic_arch_extn hacks and abuse by using the new stacked domains
NOTE: Due to the nature of these changes, patches crossing subsystems have
been kept together in their own branches.
- tegra
- Handle the LIC properly
- omap
- Convert crossbar to stacked domains
- kill arm,routable-irqs in GIC binding
- exynos
- Convert PMU wakeup to stacked domains
- shmobile, ux500, zynq (irq_set_wake branch)
- Switch from abusing gic_arch_extn to using gic_set_irqchip_flags
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0gB+
-----END PGP SIGNATURE-----
Merge tag 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
New Features
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values
Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
All Marvell EBU SoCs (Kirkwood, Dove, Orion, Armada) have the
capability of changing the location of their internal registers (i.e
the registers for most hardware blocks inside the SoC). When coming
out of reset, the internal registers are mapped at 0xd0000000, but
since years and years, the tradition has been to have the internal
registers remapped at 0xf1000000 by the bootloader, and Linux has
since then assumed that the internal registers for the SoC were
located at 0xf1000000 on Kirkwood, Dove, Orion, etc. Linux has never
been aware that those registers are remappable (and there is no way to
know where they are mapped at runtime, since the register to configure
the address of the registers is itself within the internal registers).
Then came the Armada 370 and Armada XP, in which some of the very
early silicon steppings had an issue, which forced to use 0xd0000000:
the SoC was no longer working properly when the internal registers
were remapped at 0xf1000000. This issue is only affecting very early
silicon steppings and production steppings are not affected: the issue
has been fixed in between.
Since what we (Free Electrons) used to do the initial submission of
the Armada 370 and Armada XP platforms was evaluation boards with
those very early steppings, we submitted Device Tree that assumed the
internal registers were mapped at 0xd0000000. This is the case for
Armada 370 DB, Armada XP DB and Armada XP GP.
However, in practice, since Marvell has been shipping the evaluation
boards with production steppings of the SoC, they are shipping those
boards with bootloaders that remap the registers to 0xf1000000. We
have already changed this internal register address to 0xf1000000 for
the Armada XP DB in commit 82066bdb5a and for the Armada XP GP in
commit 91ed32200e (both merged in v3.15).
We only recently got our hand on an Armada 370 DB with a production
stepping of the SoC, which uses a bootloader that remaps internal
registers at 0xf1000000. Therefore, this commit aligns the Armada 370
DB to be like the Armada XP DB and Armada XP GP: assume that the
internal registers are mapped at 0xf1000000.
We would like to stress out the fact that the usage of 0xd0000000 as
the internal register base address was a temporary workaround for
early steppings deficiencies, and that the real long-term solution is
the usage of 0xf1000000. Having 0xd0000000 is an *accident* in the
life of the Marvell platform support in the kernel, as is confirmed by
the usage of 0xf1000000 in all previous Marvell platforms (Dove,
Kirkwood, Orion).
There are unfortunately a number of commercial devices that continue
to use 0xd0000000 even though they use production steppings of the
SoC, simply because the vendors of such devices have never bothered
using a more recent bootloader version from Marvell. There is not much
we can do about it, and we plan on keeping 0xd0000000 in the Device
Tree of such devices.
The main reason for remapping the internal registers at 0xf1000000
instead of 0xd0000000 is that it leaves more space in the 0 -> 4 GB
part of the physical address space for RAM. With registers at
0xd0000000, all RAM between 0xd0000000 to 0xffffffff is lost because
it's covered by the I/O registers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedameon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Sz8u
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.1" from Kukjin Kim:
- for exynos3250
: add assigned clock parents for CMU nodes
- for exynos4412-odroid
: add eMMC reset line
- for exynos5250
: fixed typo for interrupt-cells
- for exynos5250-snow
: define stdout-path property
: represent bridge and panel connection
: enable wifi power-on and add cap-sdio-irq to wifi mmc node
- for exynos5250-spring
: define stdout-path property
- for exynos5420
: fixed typo for interrupt-cells
: add async-bridge clocks for gsc and disp1 PDs
- for exynos5420 boards
: Mux XMMCnDATA[0] pad correctly
- for exynos5420-odroidxu3
: add eMMC reset line
- for Peach boards
: add HS400 support and define stdout-path property
: add mclk entry and add WiFi module support
: represent bridge and panel connection
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fixed typo interrupt-cells for exynos5420 and exynos5250
ARM: dts: Add HS400 support for exynos5420 and exynos5800
ARM: dts: add async-bridge clocks to gsc power domain for exynos5420
ARM: dts: add async-bridge clocks to disp1 power domain for exynos5420
dt-bindings: add asynchronous bridge clock for exynos
ARM: dts: Define stdout-path property for exynos5250-spring
ARM: dts: Define stdout-path property for exynos5250-snow
ARM: dts: Define stdout-path property for Peach boards
ARM: dts: Add assigned clock parents to CMU node for exynos3250
ARM: dts: Add mclk entry for Peach boards
ARM: dts: Add WiFi module support for Peach boards
ARM: dts: Mux XMMCnDATA[0] pad correctly for Exynos5420 boards
ARM: dts: add eMMC reset line for exynos5422-odroidxu3
ARM: dts: add eMMC reset line for exynos4412-odroid-common
ARM: dts: represent bridge and panel connection for exynos5420-peach-pit
ARM: dts: represent bridge and panel connection for exynos5250-snow
ARM: dts: Add cap-sdio-irq to wifi mmc node for exynos5250-snow
ARM: dts: Enable wifi power-on for exynos5250-snow
Signed-off-by: Olof Johansson <olof@lixom.net>
After 57a38effa5 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb1 interface refuses to work properly because it tries
to cling to address 0 which isn't able to communicate in broadcast with
the mac anymore. The micrel phy on the board is actually configured
to show up at address 1.
Adding the phy node and its real address fixes the issue.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: <stable@vger.kernel.org> #3.19
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes have no influence on the kernel behavior (except
removing a warning message), but they allow to have a better
representation of the hardware.
- conform L2CC node with ePAPR specification by adding cache-level
- remove cpuclk resources overlapping coredivclk registers on Armada XP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlUdAKQACgkQCwYYjhRyO9XKEgCgozRuaKXoWuFy8F2LUceCTEl0
y/cAoJOZjhbCTH81dyEFzJSXyUzXXWFX
=VUFU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1-3' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: dt changes for v4.1 (round 3)" from Gregory Clement:
mvebu dt changes for v4.1 (part #3)
These changes have no influence on the kernel behavior (except
removing a warning message), but they allow to have a better
representation of the hardware.
- conform L2CC node with ePAPR specification by adding cache-level
- remove cpuclk resources overlapping coredivclk registers on Armada XP
* tag 'mvebu-dt-4.1-3' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Conform L2CC node with ePAPR specification by adding cache-level
ARM: mvebu: clk: remove cpuclk resources overlapping coredivclk registers on Armada XP
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix build breakage exynos cpuidle driver on !SMP
because it is coupled built-in so added check for SMP.
- Fix lid, power pin-functions and mmc node updates
for exynos5250-spring: Fixes commit ID 53dd4138bb
("ARM: dts: Add exynos5250-spring device tree")
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPV1
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung 2nd fixes for v4.0" from Kukjin Kim:
- Fix build breakage exynos cpuidle driver on !SMP
because it is coupled built-in so added check for SMP.
- Fix lid, power pin-functions and mmc node updates
for exynos5250-spring: Fixes commit ID 53dd4138bb
("ARM: dts: Add exynos5250-spring device tree")
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of changes to improve support on the Nyan Big (Acer Chromebook
13). These enable the trackpad and make the WiFi card work. Changes to
the userspace-exposed name of the soundcard are required for a better
audio experience.
Support for Nyan Blaze (HP Chromebook 14) is added. It is very similar
to Nyan Big and therefore can enjoys many of the above improvements.
Since the EMC driver can now be used to scale the frequency at which
external memory is clocked, corresponding EMC frequency tables are added
for Jetson TK1 and the Nyan boards.
The Jetson TK1, Beaver and Nyan boards now also use generated pinmux
data, which makes it easier to keep it in sync with the data provided by
syseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yFLx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.1-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v4.1-rc1" from Thierry Reding:
A bunch of changes to improve support on the Nyan Big (Acer Chromebook
13). These enable the trackpad and make the WiFi card work. Changes to
the userspace-exposed name of the soundcard are required for a better
audio experience.
Support for Nyan Blaze (HP Chromebook 14) is added. It is very similar
to Nyan Big and therefore can enjoys many of the above improvements.
Since the EMC driver can now be used to scale the frequency at which
external memory is clocked, corresponding EMC frequency tables are added
for Jetson TK1 and the Nyan boards.
The Jetson TK1, Beaver and Nyan boards now also use generated pinmux
data, which makes it easier to keep it in sync with the data provided by
syseng.
* tag 'tegra-for-4.1-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add EMC timings to Nyan Blaze device tree
ARM: tegra: Add EMC timings to Nyan Big device tree
ARM: tegra: Add EMC timings to Jetson TK1 device tree
ARM: tegra: Add EMC to Tegra124 device tree
ARM: tegra: Add Tegra124 ACTMON support
of: Add binding for NVIDIA Tegra ACTMON node
ARM: tegra: nyan: The WiFi card is kept powered during suspend
ARM: tegra: nyan: Add gpio-restart node
ARM: tegra: nyan: Set maximum frequency for SPI flash
ARM: tegra: Use generated pinmux data for Nyan Big
ARM: tegra: Use pwrseq-simple for the wifi in Nyan
ARM: tegra: Add node for trackpad in Nyan boards
ARM: tegra: Add DTS for the nyan-blaze board
ARM: tegra: Move generic parts out of the nyan-big DT
ARM: tegra: Change model of sound card in Nyan Big
ARM: tegra: Use generated pinmux for Beaver board
ARM: tegra: Import latest Jetson TK1 pinmux
Signed-off-by: Olof Johansson <olof@lixom.net>
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Uqd0
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v4.1" from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the -rc cycle.
This is mostly to enable errata 798181 and thermal support for dra7,
configure ocp2scp for am437x, remove dead code for OMAP4_ERRATA_I688
and fix build warnings for omap1510 only config.
* tag 'omap-for-v4.1/fixes-0' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
Signed-off-by: Olof Johansson <olof@lixom.net>
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVFWAiAAoJELescNyEwWM0pK8IALUinCT+Ec/Oi5WwGJaLgQgw
exlDFAcmml0xisxglGL7eHcvNBs/j4wFD37mqDUszrGW3jrM+Ex+/cvUzWIlEyZl
LjG99ZF2j51LFxDHMgpRwg1aD/NNQsQjwsuHHdCr+NHB5R2C0M4umsgX6Kt6/PE4
95LOnnjBOx4FkMOG9mZElzldUlqnhWd6drjQ9qZQar9VVVewfbR1LH/xQhjrCL0w
nwRzJwYj1LnLFO0hBVUAJSfvYltMF9PxBEx0FkyzN7QcuP1tLQ25NmGEvarHP6iZ
XpvTZ7akzButyUQbvz/kf6a0agPNUv1HHEqh7/Zddvgm//+p8nEBORuJ/cC6g1E=
=UHCi
-----END PGP SIGNATURE-----
Merge tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/drivers
Merge "arm-cci PMU updates for 4.1" from Will Deacon:
CCI-400 PMU updates
This series reworks some of the CCI-400 PMU code so that it can be used
on both ARM and ARM64-based systems, without the need to boot in secure
mode on the latter. This paves the way for CCI-500 support in future.
* tag 'arm-perf-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ARM common idle state device bindings for cpuidle support for APQ
8064.
Support Standalone power collapse (SPC) idle state (power down that does not
affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ARM common idle states device bindings for cpuidle support for APQ
8084.
Support Standalone power collapse (SPC) idle state (power down that does not
affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add ARM common idle states device bindings for cpuidle support for APQ
8974/8074.
Support Standalone power collapse (SPC) idle state (power down that does
not affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the SAW2 DT bindings to add qcom,apq8064-saw2-v1.1-cpu compatible
binding string to configure SPM registers and allow the SPM to put the
core in deeper idle states when the core is idle.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Each Krait CPU in the QCOM 8084 SoC has an SAW power controller to
regulate the power to the cpu and aide the core in entering idle states.
Reference the SAW instance and associate the instance with the CPU core.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Each Krait CPU in the QCOM 8074/8974 SoC has an SAW power controller to
regulate the power to the cpu and aide the core in entering idle states.
Reference the SAW instance and associate the instance with the CPU core.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Model the Qualcomm Technologies LPASS hardware for the ipq806x SOC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
PMA8084 have 2 SPMI devices per physical package. Add their
configuration nodes and include them in boards which are using
AQP8084 based chipset.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
PM8841 and PM8941 have 2 SPMI devices per physical package.
Add their configuration nodes and include them in boards
which are using 8x74 based chipset.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SPMI PMIC Arbiter configuration nodes for APQ8084 and MSM8974.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the node for the LPASS clock controller found on a few qcom
SoCs so that the clock driver can probe.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
[sboyd@codeaurora.org: Added apq8064 and msm8960 nodes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds TCSR support for use by the GSBI to automatically
configure ADM CRCI values based on the GSBI port configuration.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds TCSR support for use by the GSBI to automatically
configure ADM CRCI values based on the GSBI port configuration.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds TCSR support for use by the GSBI to automatically
configure ADM CRCI values based on the GSBI port configuration.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds TCSR support for use by the GSBI to automatically
configure ADM CRCI values based on the GSBI port configuration.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
data instead of platform data from Eliad Peller <eliad@wizery.com>:
- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.
- Update the current users to use the bindings instead of pdata-quirks.
- Finally, remove the deprecated wl12xx_platform_data struct
Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.
As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nr1k
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:
Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:
- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.
- Update the current users to use the bindings instead of pdata-quirks.
- Finally, remove the deprecated wl12xx_platform_data struct
Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.
As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.
* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
wlcore: remove wl12xx_platform_data
ARM: dts: add wl12xx/wl18xx bindings
wlcore: add device-tree support
dt: bindings: add TI's wilink wireless device
wl12xx: use frequency instead of enumerations for pdata clocks
wlcore: set irq_trigger in board files instead of hiding behind a quirk
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Broadcom Device Tree changes for 4.1 #3" from Brian Norris:
This pull request contains changes to the BCM7445 reference DTS files from
Brian:
- making a clock-frequency property decimal instead of hexadecimal
- adding the irq0 interrupt controller node to make the reference DTS bootable
again
* tag 'arm-soc/for-4.1/devicetree-part-3' of http://github.com/broadcom/stblinux:
ARM: dts: brcmstb: add IRQ0 controller
ARM: dts: brcmstb: un-hexify clock frequency
Signed-off-by: Olof Johansson <olof@lixom.net>
- add support for Performance Monitor Unit on most of mvebu SoCs
- add nas2big support
- add support for USB3 port On Armada 385 AP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlUL6VsACgkQCwYYjhRyO9Vm/wCfZNIo3l1U82ietdSE8zuVWq1U
A2gAmQHeLLV6izood0nm9/AvvcMHPpI5
=rtR1
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: dt changes for v4.1 (round 2)" from Gregory Clement:
mvebu dt changes for v4.1 (part #2)
- add support for Performance Monitor Unit on most of mvebu SoCs
- add nas2big support
- add support for USB3 port On Armada 385 AP
* tag 'mvebu-dt-4.1-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-385-ap: Enable USB3 port
ARM: mvebu: Enable Performance Monitor Unit on Armada 380/385 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada 375 SoC
ARM: mvebu: Enable Performance Monitor Unit on Armada XP/370 SoCs
ARM: Kirkwood: add DT description for nas2big
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support for ChiliSOM
- Add support for OpenPandora
- Add support for BeagleBoard NAND
- Enable crypto devices for omap3 devices
- Add bindings for omap3 camera support
- Updates for am437x and dra7x and dm816x SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BU88
-----END PGP SIGNATURE-----
Merge tag 'v4.1-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v4.1, part1" from Tony Lindgren:
Device tree related changes for omaps:
- Add support for ChiliSOM
- Add support for OpenPandora
- Add support for BeagleBoard NAND
- Enable crypto devices for omap3 devices
- Add bindings for omap3 camera support
- Updates for am437x and dra7x and dm816x SoCs
* tag 'v4.1-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: dts: Update Nanobone dts file
ARM: dts: n950, n9: Add primary camera support
ARM: dts: omap3: Add DT entries for OMAP 3 ISP
Documentation: DT: Add bindings for omap3isp
ARM: dts: Remove files omap34xx-hs.dtsi and omap36xx-hs.dtsi
ARM: dts: omap3-tao3530: Include directly omap34xx.dtsi
ARM: dts: n900: Enable omap sham and include directly omap34xx.dtsi
ARM: dts: n9/n950: Enable omap crypto support
ARM: dts: Remove PIN_INPUT for dm816x McSPI
ARM: dts: Add cppi41 support for dm816x MUSB
ARM: dts: Fix typo for dm816x usb0_pins
ARM: dts: dra7x-evm: beagle-x15: Fix USB Peripheral
ARM: dts: am57xx-beagle-x15: Do not include the atl header
ARM: dts: DRA7: Remove ti,timer-dsp and ti,timer-pwm properties
Documentation: omap-twl4030: Move ti,codec property to optional
ARM: dts: omap3: Remove all references to ti,codec property
ARM: dts: omap3-beagle: Add NAND device
ARM: dts: AM4372: update hdq compatible property
ARM: dts: omap3-pandora: add DM3730 1 GHz version
ARM: dts: omap3-pandora: add OMAP3530 600 MHz version
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the N900's accelerometer to
the Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight-default-sink configuration option has been
removed from the framework. As such remove it from DT and bindings.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now there are generic phy type constants declared in phy.h, migrate over to
using them rather than defining our own. This change has been done as one
atomic commit to be bisectable.
Note: The values of the defines are the same, so there is no ABI breakage
with this patch.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
- reworked arch/arm/mach-at91/Kconfig and arch/arm/Kconfig to switch to
multi-platform
- updated at91_dt_defconfig
- continue the cleanup of unneeded files and code chunks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVCv+EAAoJEAf03oE53VmQRgQIALCEppiZCt7xzH8bbGToyiSh
A1lWqDFm5kvkUW9igaks1XenxcDmKg7TwLfjolyqny20CL6/rt1oap07Yt7eAIW1
6KdCKk7RML0vduX3F/wl+ZQe6ykob0vWzaeeUNI1RgBkD7hsZCb60Re1fj44pR99
dgj08EAme1yBvvFN2iA7IWUXJMPIuQ+uFzFUMiPVahgR49AbTG/TLfGHWM8i/H15
HF/ETeShV4k02lqipm4E8te0VAiDjYcrpc12NbQ0M1jFgD+1V+tY0IvrrtTcxHEe
53CCwN09nKJTRBZrPyCdKK7r4xrpPb64ZydBWXOHkVizS24jG1fc4aXG74qBooI=
=uyvg
-----END PGP SIGNATURE-----
Merge tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/multiplatform
Merge "at91: multiplatform for 4.1 #1" from Nicolas Ferre:
This is the multi-platform support for AT91:
- reworked arch/arm/mach-at91/Kconfig and arch/arm/Kconfig to switch to
multi-platform
- updated at91_dt_defconfig
- continue the cleanup of unneeded files and code chunks
* tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: (61 commits)
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add DMA sound support to r8a7791 and r8a7790 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j+iC
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC DT Updates for v4.1" from Simon
Horman:
* Add DMA sound support to r8a7791 and r8a7790 SoCs
* tag 'renesas-dt3-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: sound enables Audio DMAC entry on DTSI
ARM: shmobile: r8a7790: sound enables Audio DMAC entry on DTSI
ARM: shmobile: r8a7791: enable Audio DMAC peri peri via sound driver
ARM: shmobile: r8a7790: enable Audio DMAC peri peri via sound driver
ARM: shmobile: r8a7791: add reg-names for sound
ARM: shmobile: r8a7790: add reg-names for sound
Signed-off-by: Olof Johansson <olof@lixom.net>
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVCaAEAAoJEPOmecmc0R2BXykH/iDpn2Nd+wZz9gj3VZgK+COg
+yJZx9hTNvdHw09XPwSHNixUyNCydQC3yTqJ1oJNa+xLpYQ/ClNUOJUv0gnoAPc5
LVzcjdRAt1zMjxawx1GmfEfgDCwxdWGyjY+dEIJqVeDANB4rsbpy2WD080NcpH7O
wzZauc+Vl2TaG/ZhJe/uC1F9lZy3ucxQi8hARk77ixkosVb7skXWTBvnSasE17hV
MMEPjyky28HuD4eY3BR5XIpnzc2rhynRNRruK9yv7Oqf5g4q/BJOXqgij3dUXrs5
4eG/umuBi9vx2i8b2GhUbG0GFQag2pIrznKkO3ttLbBU69BAxTI7gy73BrYp96A=
=dnz7
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:
This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.
* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: complete rk3288-evb pmic supplies
ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
ARM: dts: add rk3288 PopMetal board
dt-bindings: add root compatible property for PopMetal board
ARM: dts: rockchip: enable gmac on rk3288-firefly
ARM: dts: rockchip: enable usbphy on rk3288-firefly
ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
ARM: dts: rockchip: add rk3288 usb PHY
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add multiplatform support to sh73a0 and its kzm9g board
* Use Bus State Controller to enable ethernet for multiplatform sh73a0/kzm9g
* Add PM domain support to multiplatform sh73a0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7DUP
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Merge "Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1" from Simon
Horman:
* Add multiplatform support to sh73a0 and its kzm9g board
* Use Bus State Controller to enable ethernet for multiplatform sh73a0/kzm9g
* Add PM domain support to multiplatform sh73a0
* tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
ARM: shmobile: sh73a0: Remove restart callback
ARM: shmobile: sh73a0 dtsi: Add PM domain support
ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt()
ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node
ARM: shmobile: kzm9g-reference: Remove board C code and DT file
ARM: shmobile: kzm9g dts: Move Ethernet node to BSC
ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node
ARM: shmobile: kzm9g: Build DTS for Multiplatform
ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts
ARM: shmobile: sh73a0: Add Multiplatform support
ARM: shmobile: sh73a0: Introduce generic setup callback
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch creates the l4_cfg and l4_wkup interconnects for DRA7, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates the l4_cfg and l4_wkup interconnects for OMAP5, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates the l4_cfg and l4_wkup interconnects for OMAP4, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4_wkup interconnect for AM43xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM nodea as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Pinmux node should be a reference to the base one, not a complete re-write
of it. Having the node like this also prevents modifying the node layout
in the base am4372.dtsi file, which is needed for control module changes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_wkup interconnect for AM33xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_core interconnect for OMAP3, and moves some
of the generic peripherals under it. System control module nodes are
moved under this new interconnect also, and the SCM clock layout
is changed to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4 / l4-wkup interconnects for omap2420 / omap2430
SoCs, and moves some of the generic peripherals under it. System control
module nodes are moved under this new interconnect also, and the SCM
clock layout is changed to use the new SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the DT description for the SGTL5000 found on the Hummingboard Pro
model.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds some not yet defined pinfunctions. It also adds two
comments about mistakes in the i.MX25 reference manual so it is easier
to spot the difference between reference manual and pinfunction
definitions.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
While adding the MSCM interrupt router, all interrupts have been moved
to vfxxx.dtsi again. However, some properties got lost. Readd the
missing interrupt properties.
Fixes: 97e6466ab9d0 ("ARM: dts: vf610: add Miscellaneous System Control
Module (MSCM)")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Cubox has a recessed button between the HDMI and RJ-45 connectors
that wasn't mapped in the device tree, so I've mapped it to gpio-keys
BTN_0.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Tested-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds a new file, tegra124-nyan-blaze-emc.dtsi that contains
valid timings for the EMC memory clock. The file is included to the
main device tree file for the Nyan Blaze.
The frequency 528MHz is missing because we don't currently have a timing
configuration that works.
Additionally, only the timings for the ram-code 1 is present as that's
what could be tested currently, though downstream has timings for more
ram-codes.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a new file, tegra124-nyan-big-emc.dtsi that contains
valid timings for the EMC memory clock. The file is included to the
main device tree file for the Nyan Big.
The frequency 528MHz is missing because we don't currently have a timing
configuration that works.
Additionally, only the timings for the ram-code 1 is present as that's
what could be tested currently, though downstream has timings for more
ram-codes.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a new file, tegra124-jetson-tk1-emc.dtsi that contains
valid timings for the EMC memory clock. The file is included to the
main Jetson TK1 device tree.
The data is generated from the V5.0.17 version of the DVFS tables.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a node for the EMC memory controller. It is always enabled, but only
provides read-only functionality without board-specific timing tables.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Setup pwm lines as follows -
pwm1: In case HummingBoard base carrier; this pin drives through a serial
capacitor the mono out of the audio jack.
In case HummingBoard pro the this pad can be reached by wiring to
C8 capacitors on the board.
pwm2: Setup pwm2 on gpio-1 but leave the default function of the iopad as
a gpio.
The user can change the io pad mux in user space and therefore use
this function on gpio-1 (pin number 7 on the 26 pin header).
pwm3,pwm4: unused
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
[tweaked alias for pwm pinctrl group --rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the commented out PCF8523 RTC support for Hummingboard pro
base boards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It may be useful to disable the internal snvs-rtc when an external rtc is
available. This patch adds a label so that dts files can disable it.
Based on a patch from Markus Pargmann for imx6qdl.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It may be useful to disable the internal snvs-rtc when an external rtc is
available. This patch adds a label so that dts files can disable it.
Based on a patch from Markus Pargmann for imx6qdl.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Warp has a Murata chip based on a BCM4330 that provides Wifi and Bluetooth
functionality.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
input values are only useful for pin functions which define a input
register. This patch removes all input values of pin functions which do
not have an input configuration register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the Miscellaneous System Control Module (MSCM) to the base
device tree for Vybrid SoC's. This module contains registers
to get information of the individual and current (accessing)
CPU. In a second block, there is an interrupt router, which
handles the routing of the interrupts between the two CPU cores
on VF6xx variants of the SoC. However, also on single core
variants the interrupt router needs to be configured in order
to receive interrupts on the CPU's interrupt controller. Almost
all peripheral interrupts are routed through the router, hence
the MSCM module is the default interrupt parent for this SoC.
In a earlier commit the interrupt nodes were moved out of the
peripheral nodes and specified in the CPU specific vf500.dtsi
device tree. This allowed to use the base device tree vfxxx.dtsi
also for a Cortex-M4 specific device tree, which uses different
interrupt nodes due to the NVIC interrupt controller. However,
since the interrupt parent for peripherals is the MSCM module
independently which CPU the device tree is used for, we can move
the interrupt nodes into the base device tree vfxxx.dtsi again.
Depending on which CPU this base device tree will be used with,
the correct parent interrupt controller has to be assigned to
the MSCM-IR node (GIC or NVIC). The driver takes care of the
parent interrupt controller specific needs (interrupt-cells).
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USDHC2 port uses all the 8 data signals, so pass the 'bus-width' property
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PU regulator is enabled during boot, but not necessarily always-on.
It can be disabled by the generic pm domain framework when the PU power
domain is shut down. The ramp delay of 150 us might be a bit conservative,
the value is taken from the Freescale kernel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled and a list of clocks to be enabled during powerup
for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled, and a list of phandles to all clocks that must be
enabled during powerup for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The chipidea driver adds an extra line of spam to the log when a
host-only chipidea instance is left set to the default of a dual role
controller.
[ 2.010873] ci_hdrc ci_hdrc.1: doesn't support gadget
Set the dr_mode property to host on all the host-only nodes
to avoid this warning.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The WaRP Board is a Wearable Reference Plaform. The board features:
- Freescale i.MX6 SoloLite processor with 512MB of RAM
- Freescale FXOS8700CQ 6-axis Xtrinsic sensor
- Freescale Kinetis KL16 MCU
- Freescale Xtrinsic MMA955xL intelligent motion sensing platform
The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.
For more information about the project, visit:
http://www.warpboard.org/
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The anyway depricated gpio-range-cells property was never used
by the pin controller driver. This patch removes it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
IMX6 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the GPC block is actually the first
interrupt controller in the chain, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs won't even boot.
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add some defines currently missing, fix ordering to make the list
sorted by (mux_reg, mux_val), make sure pins are grouped by mux_reg.
The same definitions are missing from the old pinmux header
(arch/arm/mach-imx/iomux-mx25.h) but as only legacy machine support uses
that and therefor the existing list is obviously good enough I didn't
spend the effort to add the corresponding definitions there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Noticed while looking over the pad definitions. None of the bogus
definitions is used in-tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It may be useful to disable the internal rtc snvs-rtc because an
external rtc is available. This patch adds a label so that board files
can disable this rtc.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MIPI DSI node contains some ports which represent possible DRM CRTCs
it can connect with. Each port has a 'reg' property embedded. This
property will be wrongly interpretted by the MIPI DSI bus driver, because
the driver will take each subnode which contains a 'reg' property as a
DSI peripheral device. This patch moves the existing MIPI DSI ports into
a new 'ports' node so that the MIPI DSI bus driver may distinguish its
DSI peripheral device(s) from the existing ports.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since imx6sx-sdb reva board is experimental and will not be used
formally (eg, no software release based on it), we set revb board
as the formal imx6sx-sdb board.
The imx6sx-sdb uses pfuse200 as pmic which has only one power supply
for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to
use the same (higher one in the same frequency) one as its power supply,
that's the reason we override the OPP setting in board dts file.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6sx sdb board has two revisions, the current mainline one
is reva which is experimental and mainly for internal use. In
this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and
move the reva dedicated contents to imx6sx-sdb-reva.dts.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MCP2515 CAN controller is available on Colibri Evaluation board.
Hence enable MCP2515 CAN.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e6O1
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.0
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eCH/
-----END PGP SIGNATURE-----
Merge tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for the -rc cycle:
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix interrupt number for SPI1 interface
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVCxZzAAoJEBmUBAuBoyj0V3YQAJN24cPBrxeyAG1atuHN2T9r
8QtJ2eVOU32IwzNoOl1PHITGaf1b3Ks03NC+GSk3WMAzMJ/fJMY2p6ABpCCrriBZ
xRZfkqqlJlB6/BNb62BkUK45yy0chgxoPoaDiX9CR0KqBeVciZM0Ag4Tw82oQDDF
mEBKJxSO7GIzRj5uHzQHaTh6Fi6QMRYLYDMyoRNom1tpdOLm7ufyWI++q6FLk2/W
YAxI8tj+AN48cgTB9oO+K83RjxVuR7YM4xQPUJ3K21AAAc1AHhXgOyzMd2FZhIhJ
qC5xODFXVcG5+m6/7vYxkBnLo9sexHF8EdD7ByRE2KMoRrsWU2s304ErUBfzp635
9LbSHZB2HD3rM7KEz/QiRGYkijACgVVBbIImHAaAbd4H13hz4FevKARPNvFz9u62
Bu3jYj94wuGJYHuiIa9p4QZcMaQVSThBsnWUfq18l1UljIoeRzK4jt0P/DCowRJO
J3gtmH1E/N/NKGbw1RqNwqSydUqdbeyDdOua/2oLrEaOthJATCj3eFCTpIK5lrQD
Ttc3EsdL7r2OVD7zOXZsbH9mZXxgDnIu0E4Ocm3F3Xs22ERRMVPiDb0xvwXbtq5+
uN0HdFN2P7wb02dv2r3NWcTpQEBVqvPe4VRIv+U4hgXXJJrYeEZqWYQ8Vd2d4bsb
ZkvK7CHsv9FiU3aCnT7B
=NEia
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next into fixes
Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface
* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>
BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.
NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bandgap and related thermal nodes. The patch adds 5 thermal
sensors. Only one cooling device for mpu as of now. The sensors are
the exact same on both dra72 and dra7. Introduce CPU, GPU, core nodes
for the moment as they are direct reuse of OMAP5 entities.
NOTE: OMAP4 has a finer counter granularity, which allows for a delay
of 1000ms in the thermal zone polling intervals. DRA7 have different
counter mechanism, which allows at maximum a 500ms timer. Adjust the
cpu thermal zone accordingly for DRA7.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[t-kristo@ti.com: few reuse from OMAP5 entities]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added a new compatible string "ti,am437x-ocp2scp" for OCP2SCP module.
This is needed since except for the OCP2SCP used in AM437x, SYNC2 value
in OCP2SCP TIMING should be changed whereas the default value is sufficient
in AM437x.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Changes fixes the misspelled of #interrups-cell.
arch/arm/boot/dts/exynos5420.dtsi:224: WARNING: 'interrups'
may be misspelled - perhaps 'interrupts'?
Tested on OdroidXU3 board.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
[kgene@kernel.org: added fixing same typo in exynos5250]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
HS400 timing values are added for SMDK5420, exynos5420-peach-pit
and exynos5800-peach-pi boards. This also adds RCLK GPIO line,
this gpio should be in pull-down state.
This also enables HS400 on peach-pi and this updates the clock
frequency to 800MHz to be set as input clock to controller.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
[alim.akhtar@samsung.com: addressed review comments]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Without proper regulator support for individual boards, it is dangerous
to have overclocked/overvoltaged OPPs in the list. Cpufreq will increase
the frequency without the accompanying voltage increase, resulting in
an unstable system.
Remove them for now. We can revisit them with the new version of OPP
bindings, which support boost settings and frequency ranges, among
other things.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A10-Lime is known to be unstable when running at 1008MHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Even if the host controller doesn't have power during suspend, the card
is kept powered.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Nyan Chromebooks have a GPIO line dedicated to restarting the
system. Using this line will make sure that the TPM is restarted as
well.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Google has submitted a board config for the pinmux programming of the
Nyan Big board. Use the whole of it as it's generated to make it easier
to update as the configuration gets fixed in the future.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Nyan boards have a Marvell 88w8897 wifi card connected through SDIO
that needs the reset line to be asserted before mmc power up and deasserted
afterwards.
This patch also adds references to the power supplies of the card so that
the regulators are enabled when it's probed.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Nyan boards have a eKTH3000 from Elan as their trackpad, connected
through I2C.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's commercial name is HP Chromebook 14 and is substantially similar to
the Acer Chromebook 13 (nyan-big).
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding the DT for the nyan-blaze board.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Change it from "Acer Chromebook 13" to GoogleNyanBig so it's unique and
identifiable.
With this change the card id exposed to userspace becomes GoogleNyanBig
instead of the current A13.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace the current incomplete pinmux setup with a proper one generated
using the tegra pinmux scripts.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
syseng has revamped the Jetson TK1 pinmux spreadsheet, basing the content
completely on correct configuration for the board/schematic, rather than
the previous version which was based on the bare minimum changes relative
to another reference board.
This content comes from Jetson_TK1_customer_pinmux.xlsm (v09) downloaded
from https://developer.nvidia.com/hardware-design-and-development.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For the SAMA5D4 SoC, some LCD lines are in conflict with useful peripherals.
Remove these lines and the lowest significant bit of a 24 bit LCD. It gives
us a RGB 777 configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The color arrangement for SAMA5D4 in RGB 666 takes the most significant bits of
each color line groups.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the HLCDC (HLCD Controller) IP available on some sama5d3 SoCs
(i.e. sama5d31, sama5d33, sama5d34 and sama5d36) in sama5d3 dtsi file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define alternative pin muxing for the LCDC pins.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The HLCDC (HLCD Controller) IP supports 4 different output mode (RGB444,
RGB565, RGB666 and RGB888) and the pin muxing will depend on the chosen
RGB mode.
Split pin definitions to be able to set pin config according to the
selected mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update dts file to reflect:-
* new flash memory layout
* add missing phy-mode property
* dual_emac now just a boolean
* rename mcp to microchip
* update gpio definition
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the primary camera of the Nokia N950 and N9.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The resources the ISP needs are slightly different on 3[45]xx and 3[67]xx.
Especially the phy-type property is different.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: use omap3_scm_general instead of scm_conf for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This L2 controller handles multiplexing a few different interrupts. We
also need it for configuring the interrupt forwarding masks for the
UART.
With this, we can *now* boot BCM7445 to a prompt using the upstream
kernel + DTB.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
These files are not used by any DTS file anymore.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This value makes much more sense in decimal.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch just move content of file omap34xx-hs.dtsi into omap3-tao3530.dts.
There is no code change, patch is just preparation for removing -hs file.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves content of file omap34xx-hs.dtsi into omap3-n900.dts and enable
omap sham support (omap HW support for SHA + MD5). After testing both omap hwmod
and omap-sham.ko drivers it looks like signed Nokia X-Loader enable L3 firewall
for omap sham. There is no kernel crash with both official bootloader and crypto
enable bootloader. So we can safely enable sham code.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Harmattan system on Nokia N9 and N950 devices uses omap crypto support.
Bootloader on those devices is known that it enables HW crypto support.
This patch just include omap36xx.dtsi directly, so aes and sham is enabled.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On dm816x we have no PIN_INPUT vs PIN_OUTPUT configuration, there
are just pulls. Let's remove the bogus flags.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we have cppi41 on dm816x just like on am335x.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a54879a008 ("ARM: dts: Fix USB dts configuration for dm816x")
attempted to fix the USB features introduced by commit 7800064ba5
("ARM: dts: Add basic dm816x device tree configuration") but obviously
I did not read the dmesg as more USB issues still keep trickling in.
It should be usb1_pins instead not usb0_pins for the second interface
to avoid warnings from pinctrl framework.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The socfpga.dtsi currently has the wrong interrupt number set for SPI master 1
Trying to use the master without this change results in the kernel boot
process waiting forever for an interrupt that will never occur while
attempting to probe any slave devices configured in the device tree as being
under SPI master 1.
The change works for the Cyclone V, and according to the Arria 5 handbook
should be good there too.
Signed-off-by: Mark James <maj@jamers.net>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
For L2 cache controller node, cache-level property is mandatory. Let's
add it to Armada 370 and Armada XP device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The resources of the cpuclk node are overlapping the one from
coredivclk node. It was not noticed until now because the driver did a
simple of_iomap and not a request_mem_region. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and port to 4.0-rc]
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:
platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Exynos has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the PMU block is actually the first
interrupt controller in the chain for RTC, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs may not even boot.
Also, I strongly suspect that there is more than two wake-up
interrupts on these platforms, but I leave it to the maintainers
to fix their mess.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088693-15724-2-git-send-email-marc.zyngier@arm.com
[ jac: squash in maz's fixup from
https://lkml.kernel.org/r/5506989D.9050703@arm.com ]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 385 AP board has a USB3 port exposed that uses a GPIO to drive the
VBUS line. Enable the needed drivers to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we have EXTCON_USB_GPIO queued for v4.1, revert
commit addfcde7c4 ("ARM: dts: dra7x-evm: beagle-x15: Fix USB Host")
On these EVMs, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Both GSCALER IPs in gsc power domain have async-bridges (to FIMD and MIXER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
FIMD and MIXER IPs in disp1 power domain have async-bridges (to GSCALER),
therefore their clocks should be enabled during power domain switch.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Configure the pins in external interrupt mode, as done for Snow in
e5e5c6d14e ("ARM: dts: Add power and lid GPIO keys pinctrl for
exynos5250-snow").
Reported-by: Kukjin Kim <kgene@kernel.org>
Suggested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Resolve a merge conflict with mmc refactoring aaa25a5a33 ("ARM: dts:
unuse the slot-node and deprecate the supports-highspeed for dw-mmc in
exynos") by dropping the slot@0 nodes, moving its bus-width property to
the mmc node and replacing supports-highspeed with cap-{mmc,sd}-highspeed,
matching exynos5250-snow.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Fixes: 53dd4138bb ("ARM: dts: Add exynos5250-spring device tree")
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Currently the Spring DTS has bootargs in the /chosen node and this is
kept since users that don't have a serial console on this board might
be using it to have the boot log shown in the display. This will have
more precedence than the stdout-path but it's fine since is only used
when CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Currently the Snow DTS has a bootargs in the /chosen node and this is
kept since users that don't have a serial console on this board might
be using it to have the boot log shown in the display. This will have
more precedence than the stdout-path but it's fine since is only used
when CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use assigned-clocks/assigned-clock-parents properties for
CMU clock controller DT node to secure proper clock setup:
switching the two muxes to root oscillator clock is not only
required for proper powering down the ISP power domain,
but it also reduces the risk of accessing the ISP CMU
registers while the ISP power domain remains turned off
(i.e. through the common clock framework by clk_summary)
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Armada 380 and 385 SoCs have a Cortex-A9 CPU, so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 375 SoC has a Cortex-A9 CPU, and so the PMU is available
to be used. This commit enables it in the devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 370 and XP SoCs have Cortex-A9 compatible CPUs, and with a
Performance Monitoring Unit.
Enable it so that we can have hardware-assisted perf support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Remove the 'ti,timer-dsp' and 'ti,timer-pwm' properties from the timer
nodes that still have them. This seems to be copied from OMAP5, on
which only certain timers are capable of providing PWM functionality
or be able to interrupt the DSP. All the GPTimers On DRA7 are capable
of PWM and interrupting any core (due to the presence of Crossbar).
These properties were used by the driver to add capabilities to each
timer, and support requesting timers by capability. In the DT world,
we expect any users of timers to use phandles to the respective timer,
and use the omap_dm_timer_request_by_node() API. The API to request
using capabilities, omap_dm_timer_request_by_cap() API should be
deprecated eventually.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti,codec property is not used (parsed) in omap-twl4030 driver. The ti,twl4030-audio
which ti,codec points by phandle is mfd driver and device for ASoC codec is created
w/o DT compatible string. Removing all references in DT files.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The beagle board contains a 16-bit NAND device connected to
chip select 0 of the GPMC controller.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates hdq node compatible property to "ti,am4372-hdq".
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added Pandora 1 GHz model which is based on Classic/Rebirth
with following changes:
- upgraded cpu to dm3730 runs on 1GHz
- 512 MiB DDR-333 SDRAM @ 200 MHz
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added Pandora Rebirth model which is based on Pandora
Classic with 512 MiB DDR-333 SDRAM memory.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This device tree allows to boot, supports the panel,
framebuffer, touch screen, as well as some more peripherals.
Since there is a OMAP3530 based 600 MHz variant and a DM3730 based
1 GHz variant we must include this common device tree code
in one of two CPU specific device trees.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To be able to control the gate for the clkout2 clock output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.
Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since this is a SOM (System on Module) that will be part
of another embedded board (and can't really exist on its own)
define it as a "dtsi" that will be included in the Device tree
describing the whole system later on.
Hardware specification:
* AM335x SoC
* up to 512 MB RAM
* NAND Flash (8x interface, cs0)
* UART0
* PMIC
* I2C0 (for PMIC)
* 1x Ethernet MAC
Signed-off-by: Rostislav Lisovy <lisovy@jablotron.cz>
[tony@atomide.com: updated nand io size to be just 4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The system timer register range is used to handle three different
functionalities: Periodic Interval Timer, Real Time Timer and watchdog. Declare
it as a syscon to be able to get a regmap.
Also declare it as a simple-mfd and its watchdog subnode.
Finally, document the watchdog compatible string.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVBgAuAAoJENfPZGlqN0++Ks0P/04y8/pbeyOIz3jnPXvXKjE0
ouZc+wcoIlJzV2uTpHnfNsHeepKG7HBHF3GH6DLn6Au21W68JwJ3fbV7Lo0xCI2P
gmphYThMfRLLxy0wx/tJhG99KDannzHxEIVpTjS7IYWCJMB/WX0s2pjxf5GlFlDu
sfp1AdFlw0QuOa55lUk7nluyrw6OfJoAKUZVVeK8q8gZXRju2ecnv0yeS511d38k
vrRhYip2Gone69GFIusdhDozng51YdbnAle4Z2ZLpzrkIFp+yONYvLnDlRXtxJqH
UAL6cjX4O2WewO5bgnF6dnVnwm2wfXb3WcsfWQVmpQ7ujk0GsehwGvECFODh/ikm
IViNijKOMhFJhJlR56bED/a1fDSWZs8eQf1q1lsUYCJDvsZ1bf15aaj5lVI2nZ+n
v0/p4ZbzR2dNhPNEveKKMcLO+LNHmOAH9QgvrLLHrs7osfYimht+Rd7z1mRoNnl4
nyg/SqdPVuEu52uA1EXuDPdwJm9oGU/QNaazaR3GROPvVbgodYhnni7ors5nOFyI
XRgcnW06yWUoAn5BNW67p0/mg2F1YELmp652CnWj80s7O53vc0c5vF0vmgy6fSb3
mlUqDDtUvyLROdjgW0elWph6nRIE5nFBZEylQf3PVedvKa5VxrJ6Epd03cgLw1GQ
qPeQl8tUW2z48BSTMGNb
=EXNz
-----END PGP SIGNATURE-----
Merge tag 'renesas-da9063-da9210-quirk-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC da9063/da9210 Regulator Quirk for v4.1" from Simon Horman:
The r8a7790/lager and r8a7791/koelsch development boards have da9063 and
da9210 regulators. Both regulators have their interrupt request lines
tied to the same interrupt pin (IRQ2) on the SoC.
After cold boot or da9063-induced restart, both the da9063 and da9210
seem to assert their interrupt request lines. Hence as soon as one
driver requests this irq, it gets stuck in an interrupt storm, as it
only manages to deassert its own interrupt request line, and the other
driver hasn't installed an interrupt handler yet.
To handle this, install a quirk that masks the interrupts in both the
da9063 and da9210. This quirk has to run after the i2c master driver
has been initialized, but before the i2c slave drivers are initialized.
As it depends on i2c, select I2C if one of the affected platforms is
enabled in the kernel config.
* tag 'renesas-da9063-da9210-quirk-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: Add da9063 PMIC device node for system restart
ARM: shmobile: lager dts: Add da9210 regulator interrupt
ARM: shmobile: koelsch: Add da9063 PMIC device node for system restart
ARM: shmobile: koelsch dts: Add da9210 regulator interrupt
ARM: shmobile: R-Car Gen2: Add da9063/da9210 regulator quirk
Pull "This pull request contains the following changes from Ray for Cygnus SoCs: from Florian Fainelli:
- enable IOMUX, required for pinmux/pinctrl
- enable GPIO, required for the GPIO driver
- enable GPIO hook detection for BCM911360-based phone designs
- enable PCIe controller for the bcm958300k designs
* tag 'arm-soc/for-4.1/devicetree-part-2' of http://github.com/broadcom/stblinux:
ARM: dts: enable PCIe support for Cygnus
ARM: dts: cygnus: enable GPIO based hook detection
ARM: dts: enable GPIO for Broadcom Cygnus
ARM: dts: enable IOMUX for Broadcom Cygnus
This patch introduces devicetree for the Alpine platform, and
for a development board based on the same platform.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
update to the MAINTAINERS entry adding a rockchip regexp entry.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVBIBSAAoJEPOmecmc0R2BitkH/2zUwSyOh/zTpyxS3XqzfNJa
88AKTy1FVMIfI9aaL3HjVYe9/NwcQUYj3Av/0GnwqXRsV8mCbGY0s1ou1a+Xe6qw
YR6rDBAzjKcvYk8zsPVE91L29nA81VMxbgEVLtGQmeBUzbAX4Ac9poWo9xLzSHaG
UTxA18VArMmmHn47KgOPz1S2qTQikVjpDyfPF7fU/bn6aLPLrtzHd0Bq1RI5uG8q
3rA4ZVEb18bK3DIBIH+vf1v6GTF33VZrCtTWqI5RFV9OO+0nglNfERHGx9z7gi7x
vXXze1kKnaL+nsjxjhQg/oRhN+4YlivoEt1Z2Is4v2/2sYXP6T/C7bbOVdQZQoY=
=VQ49
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "ARM: rockchip: small fixes for 4.0-rc" from Heiko Stuebner:
Adding a default-disabled state to the new gmac node and an
update to the MAINTAINERS entry adding a rockchip regexp entry.
* tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
OMAP4/5 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the WUGEN HW block, kernels with this patch applied
won't have any suspend-resume facility when booted with old DTs,
and old kernels with updated DTs won't even boot.
On a platform with this patch applied, the system looks like
this:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 0 0 WUGEN 37 gp_timer
19: 233799 155916 GIC 27 arch_timer
23: 0 0 WUGEN 9 l3-dbg-irq
24: 1 0 WUGEN 10 l3-app-irq
27: 282 0 WUGEN 13 omap-dma-engine
44: 0 0 4ae10000.gpio 13 DMA
294: 0 0 WUGEN 20 gpmc
297: 506 0 WUGEN 56 48070000.i2c
298: 0 0 WUGEN 57 48072000.i2c
299: 0 0 WUGEN 61 48060000.i2c
300: 0 0 WUGEN 62 4807a000.i2c
301: 8 0 WUGEN 60 4807c000.i2c
308: 2439 0 WUGEN 74 OMAP UART2
312: 362 0 WUGEN 83 mmc2
313: 502 0 WUGEN 86 mmc0
314: 13 0 WUGEN 94 mmc1
350: 0 0 PRCM pinctrl, pinctrl
406: 35155709 0 GIC 109 ehci_hcd:usb1
407: 0 0 WUGEN 7 palmas
409: 0 0 WUGEN 119 twl6040
410: 0 0 twl6040 5 twl6040_irq_ready
411: 0 0 twl6040 0 twl6040_irq_th
IPI0: 0 1 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 95334 902334 Rescheduling interrupts
IPI3: 0 0 Function call interrupts
IPI4: 479 648 Single function call interrupts
IPI5: 0 0 CPU stop interrupts
IPI6: 0 0 IRQ work interrupts
IPI7: 0 0 completion interrupts
Err: 0
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This block should not be enabled by default or else if the kconfig is set,
it will try to load/probe even if there's no phy connected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The DBGU is not a simple UART and we need to be able to distinguish it from the
other UARTs, in particular to get its address and check the chip id.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds the static vcc_sys regulator to the rk3288-evb, the missing
rk808 supplies from it and all the supplies of the act8846 evb-variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVAFaGAAoJEAf03oE53VmQilsH/Aie6f2WmzqtBACUTJKae3Kj
BLXyewX89rSEDuUEjImJhYdafYDEq/5IeoeRMY/qPdXKrY0KCEhwnVUT5LEH3qy3
P8yl0UAtZycMnKtP2YhFRAFUY/DozxprcOqTw4IfZ7PHHsQKcn4+qrgG8LcHpvfZ
d5wv6C+6gi9UBh3B7omOx98ULFDOnST56UhOml9HGsdOgCc7AbsusEG4FzRON7Bc
4QEJuYxxZPONoeuczpn9qF8SFk9ShO5dHQsjzWkSZjgneBPJK7vujcItR9KWWqw5
gtjQ19BPNuAYY4MY6/2mc/qOGsA3o17Cn9CvNwaAnlvMLebk4tMAWL8Y9Dmjouc=
=l68g
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes3' into at91-4.1-cleanup
Third fixes batch for AT91 on 4.0:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+DZAAAoJEAf03oE53VmQe34H/3cACqt00PvJiJ/DJNOLq8xM
1E93vZb/sQ5nD4JwF1DK1/VezT8QjOpIdb/Uo/XIKxqV0T7ZfFcLcAYHDCZup1HP
VbNtGRYPDGtQypBBVHDgCHwfgH6QVjTQJk67vjZkKmvWXFBnv6akY2XTrXLeMBKw
24nWEamrpR5tlEG5z9WIx6YFYBslDHq+R8j98AThJRo3NI+d00FPYwfDEwNf730e
T4xh/Rzz9eNbttBoTP5AeN75OXowsnpZwVicbQNtkX0E2jNdv1Ltbkpzc9zWdw8m
pL1kf+sV2MvD7KvcOrFGXMD2Ei3MCUNFdscaftQvfjutjEdmF2eIcK4qAzYRifw=
=UTAc
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' into at91-4.1-cleanup
Second fixes batch for AT91 on 4.0:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' into at91-4.1-cleanup
First fixes batch for AT91 on 4.0:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlT9S+0ACgkQCwYYjhRyO9XSkQCfcrsiF6bS+B1B9Gdu+nBwyXdC
BHYAmwUm92D7yH8ePjbKldM4ONM1315b
=yn/6
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVAFaGAAoJEAf03oE53VmQilsH/Aie6f2WmzqtBACUTJKae3Kj
BLXyewX89rSEDuUEjImJhYdafYDEq/5IeoeRMY/qPdXKrY0KCEhwnVUT5LEH3qy3
P8yl0UAtZycMnKtP2YhFRAFUY/DozxprcOqTw4IfZ7PHHsQKcn4+qrgG8LcHpvfZ
d5wv6C+6gi9UBh3B7omOx98ULFDOnST56UhOml9HGsdOgCc7AbsusEG4FzRON7Bc
4QEJuYxxZPONoeuczpn9qF8SFk9ShO5dHQsjzWkSZjgneBPJK7vujcItR9KWWqw5
gtjQ19BPNuAYY4MY6/2mc/qOGsA3o17Cn9CvNwaAnlvMLebk4tMAWL8Y9Dmjouc=
=l68g
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Third fixes batch for AT91 on 4.0" from Nicolas Ferre:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
* tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
This patch adds the DT description for the LaCie "2Big NAS" (nas2big).
This NAS is an hardware upgrade of the 2Big Network v2.
Chipset and device list:
- CPU Marvell 88F6282 1600Mhz
- SDRAM memory, 256MB DDR3 (2x128MB x8) 533Mhz
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- Flash memory, NAND 256MB TSOP48
- I2C EEPROM, 512 bytes (AT24 type)
- PCIe SATA controller JMicron JMB360 (eSATA)
- I2C fan controller GMT G762 (with a separate alarm GPIO)
- 1 USB2 host port
- 1 push button
- 1 power switch
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
- CPLD for LEDs and start-up management (Altera Max EMP3064)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18
The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly
different UDC IPs.
Those differences were previously handled with cpu_is_at91xx macro which
are about to be dropped for multi-platform support, thus we need to
change compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
There is no specific driver handling the AHB matrix, this is a simple syscon
device. the matrix is needed by several other drivers including the USB on some
SoCs (at91sam9261 for instance).
Without this definition, the USB will not work on these SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/8l7AAoJEFBXWFqHsHzOb3sH/1fFkQXzUcAon971XnD3sP55
zAbUvcowEQ/04xpb3Q5r5KCfeN4UvOCSY6Zed4sevq/TJZidYl8DKu9q4s0rSnfX
m1GghT3pAixMlyEWdJldmIwTYBXEkaJVrqeNuTB6BqBIsInWW/R+WkuByrPGkaxS
P5ENbyMVz68S0Cq88lmYzFjRXCCc2vWPZiVKj0DEOnqld1TIpY9hQyZwHmepCydZ
GKHLApyWP9qyUs/N6Bxwt/2vPoauit2xfDTvCbBk75jO34uSYEo9L9YpwDQorXPW
f6vj1EkVqW3TljghEm/kSoi1nhU2fNnfUAWClfKQ1UO2yzNLQAWtY+23upR5Qkw=
=kuEJ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.0" from Shawn Guo:
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
* tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C0ct
-----END PGP SIGNATURE-----
Merge tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes against v4.0-rc2" from Tony Lindgren:
Fixes for various omap variants, mostly minor fixes for various SoCs
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
* tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
ARM: dts: am335x-lxm: Use rmii-clock-ext
ARM: dts: am335x-bone-common: enable aes and sham
ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
ARM: dts: OMAP5: Fix the bypass clock source for dpll_iva and others
ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
ARM: OMAP2+: hwmod: fix deassert hardreset clkdm usecounting
ARM: DRA7: hwmod_data: Fix hwmod data for pcie
ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU+DZAAAoJEAf03oE53VmQe34H/3cACqt00PvJiJ/DJNOLq8xM
1E93vZb/sQ5nD4JwF1DK1/VezT8QjOpIdb/Uo/XIKxqV0T7ZfFcLcAYHDCZup1HP
VbNtGRYPDGtQypBBVHDgCHwfgH6QVjTQJk67vjZkKmvWXFBnv6akY2XTrXLeMBKw
24nWEamrpR5tlEG5z9WIx6YFYBslDHq+R8j98AThJRo3NI+d00FPYwfDEwNf730e
T4xh/Rzz9eNbttBoTP5AeN75OXowsnpZwVicbQNtkX0E2jNdv1Ltbkpzc9zWdw8m
pL1kf+sV2MvD7KvcOrFGXMD2Ei3MCUNFdscaftQvfjutjEdmF2eIcK4qAzYRifw=
=UTAc
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Second fixes batch for AT91 on 4.0" from Nicolas Ferre:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/pm: MOR register KEY was missing
ARM: at91/dt: sama5d4: fix lcdck clock definition
ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clk
ARM: at91: debug: fix non MMU debug
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pm9Y
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next into fixes
Pull "Fixes for v4.0 on the SoCFPGA platform" from Dinh Nguyen:
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
* tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: make sure socfpga_cpu1start_addr is properly flushed
ARM: socfpga: fix uart DMA binding error
ARM: socfpga: Correct SCU virtual mapping in socfpga
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the da9063 PMIC, with subnodes for rtc and wdt.
Regulator support is not yet included.
This allows the system to be restarted when the watchdog timer times
out, or when a system restart is requested.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The da9210 regulator is connected to IRQ2. Reflect this in its device
node, so the driver can use it when it gains interrupt support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Audio DMAC peri peri is no longer DMAEngine. it is supported by
sound driver. this patch enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables all 3 GPIO controllers including the ASIU GPIO, the
chipcommonG GPIO, and the ALWAYS-ON GPIO, for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This enables the IOMUX support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some at91 SoCs embed a 10/100 Mbit Ethernet IP, that is based on the
at91sam9260 SoC.
Fix at91 DTs accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The switches on r8a73a4/ape6evm do not have pull-up registers. The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.
Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb91: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1m2R
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.1" from Simon Horman:
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
* tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
ARM: shmobile: emev2 dtsi: Add PFC information
ARM: shmobile: r8a7791: smp: remap whole apmu region
ARM: shmobile: r8a7790: smp: remap whole apmu region
ARM: shmobile: koelsch: Add DU HDMI output support
ARM: shmobile: r8a7791: Correct SDHI clock labels and output-names
ARM: shmobile: r8a7794: Correct SDHI clock base address, labels and output-names
ARM: shmobile: r8a7794: alt: Enable ethernet controller
ARM: shmobile: r8a7794: Add ethernet controller to device tree
ARM: shmobile: r8a7794: Add IPMMU DT nodes
ARM: shmobile: r8a7791: Add IPMMU DT nodes
ARM: shmobile: r8a7790: Add IPMMU DT nodes
...
* Remove the sh7372 SoC and its mackerel board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lpw8
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Pull "Renesas ARM Based SoC sh7372 SoC Removal Updates for v4.1" from Simon Horman:
* Remove the sh7372 SoC and its mackerel board
* tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
Documentation: Remove ZBOOT MMC/SDHI utility and docs
ARM: shmobile: sh7372 dtsi: Remove Legacy DTSI file
ARM: shmobile: sh7372: Remove DT binding documentation
ARM: shmobile: sh7372: Remove Legacy C SoC code
ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support
ARM: shmobile: mackerel: Remove from MAINTAINERS
ARM: shmobile: mackerel: Remove defconfig
ARM: shmobile: mackerel: Remove mach-type entry
ARM: shmobile: mackerel: Remove DT binding documentation
ARM: shmobile: mackerel dts: Remove Legacy DTS file
ARM: shmobile: mackerel: Remove Legacy C board code
ARM: shmobile: mackerel: Remove ZBOOT code
[arnd: The sh7372 platform is rather dated and is believed to
have no active users on modern kernels. It stands in the way
of converting all of mach-shmobile to be multiplatform capable,
as adding pinctrl and common-clock support for it would be more
work than it's worth. As always, should any legitimate upstream
users show up in the future, we will revert this removal]
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: keep watchdog running in idle mode
dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
ARM: at91/defconfig: add at91rm9200 ethernet support
ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
ARM: at91/dt: at91sam9260: fix usart pinctrl
ARM: at91/dt: sama5d4: add missing alias for i2c0
ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
ARM: at91: pm: fix SRAM allocation
ARM: at91: pm: fix at91rm9200 standby
pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbWq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add display power domain for exynos5250
ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
ARM: dts: enable hdmi support for exynos4210-universal_c210
ARM: dts: enable hdmi support for exynos4412-odroid-common
ARM: dts: add dependency between TV and LCD0 power domains for exynos4
ARM: dts: add hdmi related nodes for exynos4 SoCs
ARM: EXYNOS: add support for sub-power domains
dt-bindings: document a note about power domain subdomains
ARM: dts: Provide dt bindings identical for Exynos TMU
ARM: dts: Trip points and sensor configuration data for exynos5440
ARM: dts: define default thermal-zones for exynos4
ARM: dts: default trip points definition for exynos5420
ARM: dts: add TMU default definitions for exynos4412
ARM: dts: Adding CPU cooling binding for Exynos SoCs
ARM: dts: Enable TMU for exynos4412-odriod-common
ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
ARM: dts: Enable TMU for exynos4210-trats
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).
This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:
of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
ttyS0 - failed to request DMA
Provide the correct DMA channels to fix this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: Philip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC, L2 cache
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
controller, MPIC interrupt controller, timer, CPU reset for SMP,
PMSU.
* I2C
* SPI
* SDHCI
* XOR
* NAND
* UART
* PCIe
Additional features will be supported in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Device Tree nodes describing the MPIC nodes on Armada 370, 375,
38x and XP had a unit address that did not match the first reg
property, as suggested by the ePAPR. This commit fixes that.
[gregory.clement@free-electrons.com: removed the armada-38x part, as it
was already applied by a previous patch]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds 'serialX' aliases for the various serial ports on
Armada 370, 375, 38x and XP platforms. It will allow the usage of the
stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Having aliases for Ethernet devices is useless, since the networking
subsystem unfortunately doesn't care about aliases to name network
interfaces.
Note that the 'aliases' nodes in armada-370-xp.dtsi and armada-xp.dtsi
become empty, but that we keep it as is since a followup patch will
re-add some aliases to it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the standard uart0 and uart1 DT labels to the Device
Tree description of the Marvell Armada 375 SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 38x had a label for UART0, but not UART1. This commit fixes
that.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Marvell Armada 38x, the USB2 controller registers are at 0x58000,
so the corresponding Device Tree node should have a unit address of
58000, and not 50000. We were using 50000 due to an incorrect
copy/pastebin of Armada 370/XP code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development Board has a 1GB NAND SLC chip from
Micron as its main storage. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a DSA section to the DT blob representing the Ethernet switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the LaCie 2Big Network v2 (net2big_v2) board, the fan alarm is not
wired to the I2C fan controller but to a separe GPIO. This GPIO can be
controlled by using the gpio-fan driver.
This patch adds the gpio-fan alarm description in the net2big_v2 DTS.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The unit-address is supposed to be equal the first reg address, which is not
the case for the MPIC, that uses the mbus-controller one. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This add common pinctrl settings for pcie[01]_clkreq, spi1, i2c[23],
and internal i2c mux. These settings have either one or two options
only, so put them into the SoC dtsi instead of repeating them on
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since turning on idle-halt in commit fe46aa679f (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT file to enable the Wireless Audio reference design based on the
BCM58305.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add pinctrl node to the DTSI file for meson8 and sub-nodes for some
standard mux configurations.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add a node for the Ethernet controller to Meson DTS file and
enable it on the Geniatech ATV1200 board.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
This adds a node for the SPI Flash Controller to the Amlogic Meson
DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Mark Brown <broonie@kernel.org>
The PHY IRQ line is connected to external IRQ8, not IRQ0. Fix DT
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds sound card using the ak4643 codec.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds an entry for an R-Car Gen. 1 sound controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[horms: Removed undocumented "renesas,rcar_sound" compat string]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 65MHz pixel clock connected to the DU clock input.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While the LEDs on r8a73a4/ape6evm are tied to VSUPPLY, they're driven by
an N-channel MOSFET. Hence the GPIO signal should be active high.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sets the extal clock to the frequency of the oscillator installed by
default (33 MHz).
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node to the new BSC node, as its connected to the
Bus State Controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: dropped compat string changes as they seem out of scope]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.
Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds domain definition and references to it in appropriate devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
[mszyprow: rebased onto generic power domains dt bindings]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds configuration of hw modules required to enable HDMI
support on Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
TV Mixer needs both TV and LCD0 domains enabled to be fully operational.
This dependency is modelled by making TV power domains a sub-domain of
LCD0 power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds entries for HDMI, Mixer and i2c with hdmi-phy modules
found in Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented device tree bindings provide data already hardcoded in the
exynos_tmu_data.c file.
After this commit, it should be possible to reuse common thermal core
framework in Exynos SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit provides information about Exynos5440 device configuration.
Previously this information was available in exynos_tmu_data.c file.
Now it is available in the device tree.
Such approach allows reusing some common code for thermal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Trip points corresponding to the one defined in the exynos_tmu_data.c
for Exynos4 have been included.
This thermal-zones attribute is afterwards reused for Exynos4210,
Exynos4412 and Exynos5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This code groups in one place default settings of trip points.
It is used in SoCs with multiple instances of TMU sensor.
Separate device tree file prevents from multiple copying of the
same data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos 4 and 5 family of SoCs uses almost identical TMU sensor to
measure the on chip temperature. For this reason it is possible to
group TMU configuration parameters in one dts file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit enables TMU IP block on the Exynos4412 Odroid based
devices such as Odroid U3.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The thermal IP block (Thermal Management Unit) called TMU has been
enabled in this device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add pcie[01] node labels to allow to reference them easily from
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We want to enforce the use of named flags in GPIO and interrupt
specifiers, include the corresponding headers to Dove's SoC dtsi.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix Dove's register addresses of uart2 and uart3 nodes that seem to
be broken since ages due to a copy-and-paste error.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900AC (Mamba) is a router that has
- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM
gregory.clement@free-electrons.com: - add ARM to the title
- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
- fix the unbalanced comment for the syscfg partition
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enabling SDIO IRQ signalling for the wifi MMC/SDIO slot
doubles the transmission transfer rate.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.
So the reset line will be left de-asserted and the enable pin will be
left asserted.
The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.
Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7791 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7790 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the three
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the four
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and
hook it up to the D4 PM domain, so the R-Mobile System Controller
driver can keep the domain powered, until the new Coresight code
handles runtime PM.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we have i2c0 sleep pinctrl state but were passing
default state anyhow. Fix that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As it turns out, tps62362 is actually on I2C bus0,
not bus1. This has gone unnoticed because Linux
doesn't use (as of now) that regulator at all, it's
setup by the bootloader and left as is.
While at that, also add missing reg property for
our regulator.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Offset for smc91x must be zero otherwise smc91x linux kernel driver does not
detect smc91x ethernet hardware in qemu N900 machine.
The 0x300 offset was used to supress a warning the smsc911x
driver produces about non-standard offset as 0x300 seems to
be the EEPROM default. As only three address lines are
connected both 0 and 0x300 will work just fine with 0 being
correct. The warning about the non-standard offset can be
fixed by writing to EEPROM as that's needed in any case to
set the MAC address.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[tony@atomide.com: updated comments, just use 0 instead of 0x0]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With legacy boot i2c buses on Nokia N900 are numbered i2c1, i2c2 and i2c3.
Commit 20b80942ef ("ARM: dts: OMAP3+: Add i2c aliases") fixed the
numbering with DT boot, but introduced a regression on N900 - aliases
become i2c0, i2c1 and i2c2. Fix that by providing the correct aliases in
the board dts.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: this is needed for legacy user space to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.
After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:
- The USB id pin on dm8168-evm is hardwired and can be changed
only by software. As there are two USB-A type connectors, let's
start both in host mode instead of otg.
- The Mentor core is configured in such a way on dm8168-evm that
it's not capable of multipoint at least on revision c board
that I have.
- We need ranges for the syscon to properly set up the phy as
children of the SCM syscon area.
- Let's not disable the second interface, the board specific
dts files can do that if really needed. Most boards should
just keep it enabled to ensure the device is idled properly.
Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Note that unlike on R-Mobile A1 (r8a7740), PM domain D4 can be powered
down without ill effects on s2ram behavior, just like on SH-Mobile AP4
(sh7372). Hence we can postpone adding a (minimal) device node for the
Coresight-ETM hardware block.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Private Timer and Watchdog, as found in the Cortex-A9
MPCore.
Without this, there's no clocksource available during early kernel
initialization, before cmt1 is initialized, leading to a lock-up if
CONFIG_CPU_IDLE=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the sh73a0 generic multiplatform case has the same feature set
as the kzm9g DT reference board code, we get rid of the latter.
DT reference code in the future shall make use of the sh73a0
multiplatform support code with the generic SoC machine vector.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the root of the device tree to the BSC node,
as it's connected to the Bus State Controller. This allows the system
to know the right position of the Ethernet node in the clock and PM
domain hierarchy, and manage the clock and PM domain appropriately.
Also rename the node's name from "lan9220" to "ethernet", to conform to
ePAPR generic name recomendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on sh73a0, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain A4S.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Build the sh73a0 KZM9G board DTB in case of Multiplatform.
The DT reference case will be removed in the future and
can be ignored for now.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sync the two DTS for the KZM9G board. The target is the file
"sh73a0-kzm9g.dts" and it is made identical to the DT reference
case with the exception of the compatbile string. In the future
the DT reference file will go away.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[geert: Update for recent changes to sh73a0-kzm9g-reference.dts]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7794 parts of the SDHI[012] device nodes.
Based on the orginal patch by Shinobu Uehara <shinobu.uehara.xc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the sh7372 DTSI file for the now unsupported sh7372 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the DTS file for the no longer supported Mackerel board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on r8a7778, to which
multiple external devices can be connected.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds pin control info for USB host and video-in devices.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declares all r8a7778 clocks supported by the legacy clock framework,
plus tmu2.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: only included dtsi changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This moves everything to the legacy dts that is missing there to make it
suitable for use with multiplatform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since ("ARM: shmobile: r8a73a4: ape6evm: Remove legacy platform"),
ape6evm is restricted to booting from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from
chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This removes the remains of the legacy ape6evm platform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the r8a73a4 generic multiplatform case has the same features as the
APE6EVM DT reference board code, we get rid of the latter. DT reference
code in the future shall make use of the r8a73a4 multiplatform support code
with the generic SoC machine vector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Update Documentation/devicetree/bindings/arm/shmobile.txt]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently the pin function controller (which is also a GPIO controller)
is instantiated before the interrupt controllers due to the order in the
DTS. At that time, the irq domains for the interrupt controllers
referenced by its interrupts-extended property cannot be found yet:
irq: no irq domain found for /interrupt-controller@e61c0000 !
Nevertheless, the core OF probing code ignores this failure, besides a
debug message that's not normally printed:
not all legacy IRQ resources mapped for pfc
and continues initialization of the device. Then, the sh-pfc driver
cannot find any IRQ resources, and thinks no interrupts are available,
causing gpio-keys to fail later:
gpio-keys keyboard: Unable to claim irq 0; error -22
gpio-keys: probe of keyboard failed with error -22
Move the pin function controller node after the interrupt controller
nodes it references to work around the bug in the core OF probing code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the ad-hoc lbsc node to the BSC node,
as its connected to the Bus State Controller. This allows the system to
know the right position of the Ethernet node in the clock and PM domain
hierarchy, and manage the clock and PM domain appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on r8a73a4, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain C4.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7790 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the CAN0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure the pinmux on kzm9d to use the serial connector for uart1.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With this information all GPIOs can make use of the PFC functionality.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
This has no run-time affect as the clock nodes are not currently used.
Fixes: 8e181633e6 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7794 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7790 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7794 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specifies clock sources and register bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the R2025D real-time clock, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.
As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.
While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Specify the device interrupt to avoid polling for end of conversion.
While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While at it rename the ak4648 node to "codec" to describe the device's
function instead of its model, and move its device-specific property
after its generic properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the control-parent property to delegate masking to the
parent interrupt controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the remaining DIV6 clocks and all possible parents for the SUB
clock.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Device Tree description of SDHCI on Armada 388 RD board was
missing. This commit adds the node for it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The binding of the armada-380-sdhci has been extended with a new
register in order to be able to use the SDR50 and DDR50 mode. This
commit add the resource associated to this new register for the
Armada 38x.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 38x SDHCI node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This was left out of the original firefly board definition due to the
ethernet support going completely through the network tree, making the
underlying nodes unavailable.
Now that everything is present enable the gmac on the firefly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable usb PHY for all usb ports on rk3288-evb.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a device_node for RK3288 SoC usb phy. It also
defines the phy to be used by three usb controllers: usb_host0/1
and usb_otg.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few fixes that came in too late to make it into the first set of pull
requests but would still be nice to have in -rc1. The majority of these
are trivial build fixes for bugs that I found myself using randconfig
testing, and a set of two patches from Uwe to mark DT strings as 'const'
where appropriate, to resolve inconsistent section attributes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hrfV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few fixes that came in too late to make it into the first set of
pull requests but would still be nice to have in -rc1.
The majority of these are trivial build fixes for bugs that I found
myself using randconfig testing, and a set of two patches from Uwe to
mark DT strings as 'const' where appropriate, to resolve inconsistent
section attributes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make of_device_ids const
ARM: make arrays containing machine compatible strings const
ARM: mm: Remove Kconfig symbol CACHE_PL310
ARM: rockchip: force built-in regulator support for PM
ARM: mvebu: build armada375-smp code conditionally
ARM: sti: always enable RESET_CONTROLLER
ARM: rockchip: make rockchip_suspend_init conditional
ARM: ixp4xx: fix {in,out}s{bwl} data types
ARM: prima2: do not select SMP_ON_UP
ARM: at91: fix pm declarations
ARM: davinci: multi-soc kernels require AUTO_ZRELADDR
ARM: davinci: davinci_cfg_reg cannot be init
ARM: BCM: put back ARCH_MULTI_V7 dependency for mobile
ARM: vexpress: use ARM_CPU_SUSPEND if needed
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
This pull request contains the following Broadcom SoCs Device Tree changes:
- Ray adds support for the Cygnus i2c Device Tree controller on Cygnus SoCs
- Fixes to the BCM63138 dtsi file for the L2 cache controller properties
* tag 'arm-soc/for-3.20/dts' of http://github.com/broadcom/stblinux:
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU4uYeAAoJEIwa5zzehBx3v58P/RGKt5e4CgCdHKjVhbPmADSE
FVECT4qrIkf4dFgU5qPCBDCtQn/B3ljxZnq6Hqi8VxYD+pRcXt94R50ZyhGUZ6QF
GLXU8jDSlY906uJwW+CHZFVLmDjTM4ONLn1ZMRtcdOrU3yGC5rZq9+Kla6ZIE6jb
mUAFMj6e+NBPYDonq93G7968EdyLJOtK4B2ylPW0+wgSRGIEPibCiNi9yyN4hBFr
LiaOyY/execKUo2K2BFWkfAZWt7GrwBu/qAkz/9YDRDiikLwFG2UBWbaik5Fj8tf
v8wvpL6Af6iLpRx1wI/HoCgjFS/g/n4O3svMe7aHGyfrkEAxNtoCKlFscO8w/aLc
eABNAb5j65it8IHvQMR5RhgqWoQe4XMlDcwsxotTe64GfxpTahdhDmhk7RKAY9Xq
MyITvtZPTPHTSZHNEDE3HtgHn62ndSinYFhdTaBi2FQxLNCUFl2TKZxpb0r65JI/
2yOf6hcgWGTgV1VOruAc5SHcSkQOY3SptM4n4F1B0VcDrCphBDYhRTdokELFJIIq
I47Week8o0f+a4ot/sf0QhU68wVZENgUJO3/Q5Buta+UGSZa4NYH7Ymc159e7hGS
k+7mCeTJC85F0H/EBWvCcZzbpwiq7jBRAY2PhqYF1EQkefdR/+28o1sX090fVaXD
n0gXv3/ZDvJB2ryv8lR/
=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
Merge fifth set of updates from Andrew Morton:
- A few things which were awaiting merges from linux-next:
- rtc
- ocfs2
- misc others
- Willy's "dax" feature: direct fs access to memory (mainly NV-DIMMs)
which isn't backed by pageframes.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (37 commits)
rtc: add driver for DS1685 family of real time clocks
MAINTAINERS: add entry for Maxim PMICs on Samsung boards
lib/Kconfig: use bool instead of boolean
powerpc: drop _PAGE_FILE and pte_file()-related helpers
ocfs2: set append dio as a ro compat feature
ocfs2: wait for orphan recovery first once append O_DIRECT write crash
ocfs2: complete the rest request through buffer io
ocfs2: do not fallback to buffer I/O write if appending
ocfs2: allocate blocks in ocfs2_direct_IO_get_blocks
ocfs2: implement ocfs2_direct_IO_write
ocfs2: add orphan recovery types in ocfs2_recover_orphans
ocfs2: add functions to add and remove inode in orphan dir
ocfs2: prepare some interfaces used in append direct io
MAINTAINERS: fix spelling mistake & remove trailing WS
dax: does not work correctly with virtual aliasing caches
brd: rename XIP to DAX
ext4: add DAX functionality
dax: add dax_zero_page_range
ext2: get rid of most mentions of XIP in ext2
ext2: remove ext2_aops_xip
...
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version).
Note: isl9305 is an I2C device so the patch does not in fact currently
depend on the introduction of "isil"-based compatible string in isl9305
driver (provided by another patch) because I2C core does not check the
prefix yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull clocksource updates from Ingo Molnar:
"The main change in this tree is the addition of various new SoC
clocksource/clockevents drivers: Conexant Digicolor SoCs, rockchip
rk3288 board, asm9260 for MIPS and versatile AB/PB boards"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dts: versatile: Add sysregs node
clocksource: versatile: Adapt for Versatile AB and PB boards
dt/bindings: Add binding for Versatile system registers
clocksource: Driver for Conexant Digicolor SoC timer
clocksource: devicetree: Document Conexant Digicolor timer binding
clockevents: rockchip: Add rockchip timer for rk3288
ARM: clocksource: Add asm9260_timer driver
clocksource: marco: Rename marco to atlas7
clocksource: sirf: Remove unused variable
Add I2C device nodes and its properties in bcm-cygnus.dtsi but keep
them disabled there. Individual I2C devices can be enabled in board
specific dts file when I2C slave devices are enabled in the future
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The L2 cache properties were completely off with respect to what the
hardware is configured for. Fix the cache-size, cache-line-size and
cache-sets to reflect the L2 cache controller we have: 512KB, 16 ways
and 32 bytes per cache-line.
Fixes: 46d4bca044 ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This commit adds the Device Tree
description of this interface at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that alarm support for ISL12057 chip is available w/ the specific
"isil,irq2-can-wakeup-machine" property, let's use that feature of the
driver dedicated to NETGEAR ReadyNAS 102, 104 and 2120 specific routing of
RTC Alarm IRQ#2 pin; on those devices, this pin is not connected to the
SoC but to a PMIC, which allows the device to be powered up when RTC alarm
rings.
For that to work, the chip needs to be explicitly marked as a device
wakeup source using this "isil,irq2-can-wakeup-machine" boolean property.
This makes 'wakealarm' sysfs entry available to configure the alarm.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
A few new drivers (power button handler for AXP20x PMIC, tps65218
power button driver, sun4i keys driver, regulator haptic driver, NI
Ettus Research USRP E3x0 button, Alwinner A10/A20 PS/2 controller).
Updates to Synaptics and ALPS touchpad drivers (with more to come
later), brand new Focaltech PS/2 support, update to Cypress driver to
handle Gen5 (in addition to Gen3) devices, and number of other fixups
to various drivers as well as input core"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: elan_i2c - fix wrong %p extension
Input: evdev - do not queue SYN_DROPPED if queue is empty
Input: gscps2 - fix MODULE_DEVICE_TABLE invocation
Input: synaptics - use dmax in input_mt_assign_slots
Input: pxa27x_keypad - remove unnecessary ARM includes
Input: ti_am335x_tsc - replace delta filtering with median filtering
ARM: dts: AM335x: Make charge delay a DT parameter for TSC
Input: ti_am335x_tsc - read charge delay from DT
Input: ti_am335x_tsc - remove udelay in interrupt handler
Input: ti_am335x_tsc - interchange touchscreen and ADC steps
Input: MT - add support for balanced slot assignment
Input: drv2667 - remove wrong and unneeded drv2667-haptics modalias
Input: drv260x - remove wrong and unneeded drv260x-haptics modalias
Input: cap11xx - remove wrong and unneeded cap11xx modalias
Input: sun4i-ts - add support for touchpanel controller on A31
Input: serio - add support for Alwinner A10/A20 PS/2 controller
Input: gtco - use sign_extend32() for sign extension
Input: elan_i2c - verify firmware signature applying it
Input: elantech - remove stale comment from Kconfig
Input: cyapa - off by one in cyapa_update_fw_store()
...
In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data
driven initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/84r
-----END PGP SIGNATURE-----
Merge tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data driven
initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards"
* tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (542 commits)
ALSA: line6: toneport: Use explicit type for firmware version
ALSA: line6: Use explicit type for serial number
ALSA: line6: Return EIO if read/write not successful
ALSA: line6: Return error if device not responding
ALSA: line6: Add delay before reading status
ASoC: Intel: Clean data after SST fw fetch
ALSA: hda - Add docking station support for another HP machine
ALSA: control: fix failure to return new numerical ID in 'replace' event data
ALSA: usb: update trigger timestamp on first non-zero URB submitted
ALSA: hda: read trigger_timestamp immediately after starting DMA
ALSA: pcm: allow for trigger_tstamp snapshot in .trigger
ALSA: pcm: don't override timestamp unconditionally
ALSA: off by one bug in snd_riptide_joystick_probe()
ASoC: rt5670: Set use_single_rw flag for regmap
ASoC: rt286: Add rt288 codec support
ASoC: max98357a: Fix build in !CONFIG_OF case
ASoC: Intel: fix platform_no_drv_owner.cocci warnings
ARM: dts: Switch Odroid X2/U2 to simple-audio-card
ARM: dts: Exynos4 and Odroid X2/U3 sound device nodes update
ALSA: control: fix failure to return numerical ID in 'add' event
...
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
Now when the CDCLK I2S output clock can be handled through the clock
API the Odroid X2/U3 can be switched to the simple-audio-card DT binding.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock related properties are added to the Exynos4 I2S device nodes
so they can be referred to as clock providers. Missing i2s_opclk1
clock is added to the I2S0 node and clock properties are added
to the MAX98090 codec node to allow it to control/read frequency
of the MCLK clock directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
X11. This should make it easier to reuse these files with other
operating systems and boot loaders.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJUxuxOAAoJEOa/DcumaUyEShgP/3kdxUxjKFDxLuerOCbvUQ5p
raAXsnysEij0x0yrQcIGRKLRN/OyQ/mZYcGJIAo6f15OuUKs+q7zoFW47kKMCoHY
mDNp2bHC8j2LDp2QE7Ylib6xE1ttQFxRtABzLdem6yxuQHniHa+tkM7i6Kbil9Lk
v764iOu3BAlLBKK7IEtoGeywWmhJ3mQ9IX8Tp5i91G0JW5GG7gpfrxg2RyzbBRg6
75c3inm7nDpqQw6vBraJRLpPOD6TYTskWVPuEFiCoXJbOEBShgsE2q1RXEaJml71
lajF7abfWpsmqhv5MsCPXBYJvC4MnHM7mDdE3OMr7/sjAYUHqnssFafS/o7B9eHW
MpU/b8RBVzFlzs9PQ8WPcnOOomvgsKmuVTVTfzmdgnZDD75SMzNaZNDxYY9pISoZ
UYelj7iKITr8fWuUkslf/ywuhCQjzs27sqM947Izpj3n71X2+UsxnwL1JvAv4vmh
754I50Wo++RbbhKzm0HpkyzlGETeL97GdlCSBhWlU5nMFuUqzkSNPrSg7G9FbbpQ
FrzTiQReBw8xe3YOrkQqSvGBZmv/KkNxIUYlqjkaDU0ni1ghjL2jzzv9J1wFvzpa
yX+RFbYTj2t+foCROnsS/e4UBIwVjTpB5m96y2I+GiDRQO81ZAGote37TGCn3/6d
kuDhIBUHqNE1PyZ5IziG
=gJhY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.20-3' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: DT changes for v3.20 (round 2)" from Gregory CLEMENT:
Relicense all Armada dts{i} files under dual license of GPLv2+ and
X11. This should make it easier to reuse these files with other
operating systems and boot loaders.
* tag 'mvebu-dt-3.20-3' of git://git.infradead.org/linux-mvebu: (27 commits)
ARM: mvebu: armada-xp-synology-ds414: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-openblocks-ax3-4: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-netgear-rn2120: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78460: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78260: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78230: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-matrix: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-lenovo-ix4-300d: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-gp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-axpwifiap: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-38x: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-rd: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-385: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-380: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-370-xp: Relicense the device tree under GPLv2+/X11
...
Signed-off-by: Olof Johansson <olof@lixom.net>
fix various devices for gta04, and add USB nodes for am57xx
and dra7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sRWN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dt-pt3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 3" from Tony Lindgren:
Device tree related chages for omaps to fix dm816x syscon,
fix various devices for gta04, and add USB nodes for am57xx
and dra7.
* tag 'omap-for-v3.20/dt-pt3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: Fix dm816x pinctrl and syscon so they are children of SCM
ARM: dts: omap3-gta04: Disable keypad
ARM: dts: omap3-gta04: only power DSS when necessary.
ARM: dts: omap3-gta04: add gyroscope
ARM: dts: omap3-gta04: enable power-off for wifi card.
ARM: dts: omap3-gta04: add comments about gpios
ARM: dts: omap3-gta04: Add ramp value for twl4030 audio
ARM: dts: omap3-gta04: Enable power-off using twl4030
ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
ARM: dts: omap3-gta04: Enable twl audio vibra support
ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
ARM: dts: omap3-gta04: Fix audio node malformatting
ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Stefan Wahren