The TQ (B.A.T.M.A.N. IV) and throughput values (B.A.T.M.A.N. V) are reduced
when they are forwarded. One of the reductions is the penalty for
traversing an additional hop. This hop_penalty (0-255) defines the
percentage of reduction (0-100%).
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the u8 BATADV_ATTR_HOP_PENALTY
attribute.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh/soft-interface can optimize the handling of DHCP packets. Instead
of flooding them through the whole mesh, it can be forwarded as unicast to
a specific gateway server. The originator which injects the packets in the
mesh has to select (based on sel_class thresholds) a responsible gateway
server. This is done by switching this originator to the gw_mode client.
The servers announce their forwarding bandwidth (download/upload) when the
gw_mode server was selected.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the attributes:
* u8 BATADV_ATTR_GW_MODE (0 == off, 1 == client, 2 == server)
* u32 BATADV_ATTR_GW_BANDWIDTH_DOWN (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_BANDWIDTH_UP (in 100 kbit/s steps)
* u32 BATADV_ATTR_GW_SEL_CLASS
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can fragment unicast packets when the packet size
exceeds the outgoing slave/hard-interface MTU.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_FRAGMENTATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can use a distributed hash table to answer ARP requests
without flooding the request through the whole mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_DISTRIBUTED_ARP_TABLE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can try to detect loops in the same mesh caused by
(indirectly) bridged mesh/soft-interfaces of different nodes. Some of the
loops can also be resolved without breaking the mesh.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the
BATADV_ATTR_BRIDGE_LOOP_AVOIDANCE_ENABLED attribute. Setting the u8 to zero
will disable this feature and setting it to something else is enabling this
feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can use multiple slave/hard-interface ports at the same
time to transport the traffic to other nodes.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_BONDING_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can drop messages between clients to implement a
mesh-wide AP isolation.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH and
BATADV_CMD_SET_VLAN/BATADV_CMD_GET_VLAN commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AP_ISOLATION_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
This feature also requires that skbuff which should be handled as isolated
are marked. The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to
set/get the mark/mask using the u32 attributes BATADV_ATTR_ISOLATION_MARK
and BATADV_ATTR_ISOLATION_MASK.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The mesh interface can delay OGM messages to aggregate different ogms
together in a single OGM packet.
The BATADV_CMD_SET_MESH/BATADV_CMD_GET_MESH commands allow to set/get the
configuration of this feature using the BATADV_ATTR_AGGREGATED_OGMS_ENABLED
attribute. Setting the u8 to zero will disable this feature and setting it
to something else is enabling this feature.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the VLANs on top of
the mesh/soft-interface have configuration settings. The genl interface
reflects this by allowing to get/set it using the vlan specific commands
BATADV_CMD_GET_VLAN/BATADV_CMD_SET_VLAN.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_VLAN command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
Beside the mesh/soft-interface specific configuration, the
slave/hard-interface have B.A.T.M.A.N. V specific configuration settings.
The genl interface reflects this by allowing to get/set it using the
hard-interface specific commands.
The BATADV_CMD_GET_HARDIFS (or short version BATADV_CMD_GET_HARDIF) is
reused as get command because it already allow sto dump the content of
other information from the slave/hard-interface which are not yet
configuration specific.
The set command BATADV_CMD_SET_HARDIF will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_HARDIF
command message type that settings might have been changed and what the
current values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv configuration interface was implemented solely using sysfs.
This approach was condemned by non-batadv developers as "huge mistake".
Instead a netlink/genl based implementation was suggested.
The main objects for this configuration is the mesh/soft-interface object.
Its actual object in memory already contains most of the available
configuration settings. The genl interface reflects this by allowing to
get/set it using the mesh specific commands.
The BATADV_CMD_GET_MESH_INFO (or short version BATADV_CMD_GET_MESH) is
reused as get command because it already provides the content of other
information from the mesh/soft-interface which are not yet configuration
specific.
The set command BATADV_CMD_SET_MESH will also notify interested userspace
listeners of the "config" mcast group using the BATADV_CMD_SET_MESH command
message type that settings might have been changed and what the current
values are.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit ff4c92d85c ("genetlink: introduce pre_doit/post_doit hooks")
intoduced a mechanism to run specific code for doit hooks before/after the
hooks are run. Since all doit hooks are requiring the batadv softif, it
should be retrieved/freed in these helpers to simplify the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_dat_put_dhcp is creating a new ARP packet via
batadv_dat_arp_create_reply and tries to forward it via
batadv_dat_send_data to different peers in the DHT. The original skb is not
consumed by batadv_dat_send_data and thus has to be consumed by the caller.
Fixes: b61ec31c85 ("batman-adv: Snoop DHCPACKs for DAT")
Signed-off-by: Martin Weinelt <martin@linuxlounge.net>
[sven@narfation.org: add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=G6IW
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190201' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Avoid WARN to report incorrect configuration, by Sven Eckelmann
- Fix mac header position setting, by Sven Eckelmann
- Fix releasing station statistics, by Felix Fietkau
-----BEGIN PGP SIGNATURE-----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=M/+V
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20190201' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Avoid WARN to report incorrect configuration, by Sven Eckelmann
- Fix mac header position setting, by Sven Eckelmann
- Fix releasing station statistics, by Felix Fietkau
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of TXQ stats in the per-tid statistics the struct
station_info grew significantly. This resulted in stack size warnings
due to the structure itself being above the limit for the warnings.
To work around this, the TID array was allocated dynamically. Also a
function to free this content was introduced with commit 7ea3e110f2
("cfg80211: release station info tidstats where needed") but the necessary
changes were not provided for batman-adv's B.A.T.M.A.N. V implementation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
[sven@narfation.org: add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The caller of ndo_start_xmit may not already have called
skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr
therefore can be in the wrong position and even outside the current skbuff.
This for example happens when the user binds to the device using a
PF_PACKET-SOCK_RAW with enabled qdisc-bypass:
int opt = 4;
setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt));
Since eth_hdr is used all over the codebase, the batadv_interface_tx
function must always take care of resetting it.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Reported-by: syzbot+9d7405c7faa390e60b4e@syzkaller.appspotmail.com
Reported-by: syzbot+7d20bc3f1ddddc0f9079@syzkaller.appspotmail.com
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In a 1000 nodes mesh network (Freifunk Hamburg) we can still see
30KBit/s of ARP traffic (equalling about 25% of all layer two
specific overhead, remaining after some filtering) flooded through
the mesh. These 30KBit/s are mainly ARP Requests from the
gateways / DHCP servers.
By snooping DHCPACKs we can learn about MAC/IP address pairs
in the DHCP range without relying on ARP. This patch is in preparation
to eliminate the need for mesh wide message flooding for IPv4 address
resolution.
Also this allows to quickly update a MAC/IP pair at least in the DHT when
DHCP reassigns an IP address to a new host.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is not allowed to use WARN* helpers on potential incorrect input from
the user or transient problems because systems configured as panic_on_warn
will reboot due to such a problem.
A NULL return value of __dev_get_by_index can be caused by various problems
which can either be related to the system configuration or problems
(incorrectly returned network namespaces) in other (virtual) net_device
drivers. batman-adv should not cause a (harmful) WARN in this situation and
instead only report it via a simple message.
Fixes: b7eddd0b39 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Thanks to rigorous testing in wireless community mesh networks several
issues with multicast entries in the translation table were found and
fixed in the last 1.5 years. Now we see the first larger networks
(a few hundred nodes) with a batman-adv version with multicast
optimizations enabled arising, with no TT / multicast optimization
related issues so far.
Therefore it seems safe to enable multicast optimizations by default.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit ced72933a5 ("batman-adv: use CRC32C instead of CRC16 in TT
code") switched the translation table code from crc16 to crc32c. The
(optional) bridge loop avoidance code is the only user of this function.
batman-adv should only select CRC16 when it is actually using it.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Multiple datastructures use the hash helper functions to add and remove
entries from the simple hlist based hashes. These are often also dumped to
userspace via netlink and thus should have a generation sequence counter.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. And an external generation
sequence counter is introduced which tracks all modifications of the list.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The debug messages of batman-adv are not printed to the kernel log at all
but can be stored (depending on the compile setting) in the tracing buffer
or the batadv specific log buffer. There is also no debug module parameter
but a batadv netdev specific log_level setting to enable/disable different
classes of debug messages at runtime.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The BATMAN_ADV_DEBUGFS portion of batman-adv is marked as deprecated. Thus
all required functionality should be available without it. The debug log
was already modified to also output via the kernel tracing function but
still retained its BATMAN_ADV_DEBUGFS functionality.
Separate the entry point for the debug log from the debugfs portions to
make it possible to build with BATMAN_ADV_DEBUG and without
BATMAN_ADV_DEBUGFS.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_dbg trace event uses different functionality and datastructures
which are not directly associated with the trace infrastructure. It should
not be expected that the trace headers indirectly provide them and instead
include the required headers directly.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 00caf6a2b3 ("batman-adv: Mark debugfs functionality as
deprecated") introduced various messages to inform the user about the
deprecation of the debugfs based functionality. The messages also include
the context/task in which this problem was observed.
The datastructures and functions to access this information require special
headers. These should be included directly instead of depending on a more
complex and fragile include chain.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit dee222c7b2 ("batman-adv: Move OGM rebroadcast stats to
orig_ifinfo") removed all used functionality of the include linux/lockdep.h
from batadv_iv_ogm.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The complete size ("total_size") of the fragmented packet is stored in the
fragment header and in the size of the fragment chain. When the fragments
are ready for merge, the skbuff's tail of the first fragment is expanded to
have enough room after the data pointer for at least total_size. This means
that it gets expanded by total_size - first_skb->len.
But this is ignoring the fact that after expanding the buffer, the fragment
header is pulled by from this buffer. Assuming that the tailroom of the
buffer was already 0, the buffer after the data pointer of the skbuff is
now only total_size - len(fragment_header) large. When the merge function
is then processing the remaining fragments, the code to copy the data over
to the merged skbuff will cause an skb_over_panic when it tries to actually
put enough data to fill the total_size bytes of the packet.
The size of the skb_pull must therefore also be taken into account when the
buffer's tailroom is expanded.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Co-authored-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The announcement messages of batman-adv COMPAT_VERSION 15 have the
possibility to announce additional information via a dynamic TVLV part.
This part is optional for the ELP packets and currently not parsed by the
Linux implementation. Still out-of-tree versions are using it to transport
things like neighbor hashes to optimize the rebroadcast behavior.
Since the ELP broadcast packets are smaller than the minimal ethernet
packet, it often has to be padded. This is often done (as specified in
RFC894) with octets of zero and thus work perfectly fine with the TVLV
part (making it a zero length and thus empty). But not all ethernet
compatible hardware seems to follow this advice. To avoid ambiguous
situations when parsing the TVLV header, just force the 4 bytes (TVLV
length + padding) after the required ELP header to zero.
Fixes: d6f94d91f7 ("batman-adv: ELP - adding basic infrastructure")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
The batadv interfaces are virtual interfaces which just tunnel the traffic
over other ethernet compatible interfaces. It doesn't need serialization
during the tx phase and is using RCU for most of its internal
datastructures. Since it doesn't have actual queues which could be locked
independently, the throughput gets significantly reduced by the extra lock
in the core net code.
8 parallel TCP connections forwarded by an IPQ4019 based hardware over
5GHz could reach:
* without LLTX: 349 Mibit/s
* with LLTX: 563 Mibit/s
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A private debug logging infrastructure is currently provided via
$debug_fs/batman_adv/*/log when CONFIG_BATMAN_ADV_DEBUG is enabled. This is
not well integrated in the rest of the tracing infrastructure of the
kernel.
Other components (like mac80211 or ath10k) allow to gather the debug
messages using generic trace events which are better integrated. This makes
it possible to interact with them using the existing userspace tools.
The tracepoint batadv:batadv_dbg will now be available when
CONFIG_BATMAN_ADV_DEBUG and CONFIG_BATMAN_ADV_TRACING is activated. The log
level mask is still used for filtering as usual.
A full system trace for offline parsing can be created (and read) using:
$ batctl ll all
$ trace-cmd record -e batadv:batadv_dbg
$ trace-cmd report
The same can also be done without recording to a file
$ batctl ll all
$ trace-cmd stream -e batadv:batadv_dbg
The trace infrastructure is especially helpful when tracing processes:
$ batctl ll all
$ ./tools/perf/perf trace --event "batadv:*" batctl p 10.204.32.1
0.000 batadv:batadv_dbg:batman_adv bat0 Parsing outgoing ARP REQUEST
0.045 batadv:batadv_dbg:batman_adv bat0 ARP MSG = [src: a2:64:14:53:f8:22-10.204.32.185 dst: 00:00:00:00:00:00-10.204.32.1]
0.067 batadv:batadv_dbg:batman_adv bat0 Entry updated: 10.204.32.185 a2:64:14:53:f8:22 (vid: -1)
0.099 batadv:batadv_dbg:batman_adv bat0 batadv_dat_select_candidates(): IP=10.204.32.1 hash(IP)=48902
0.757 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 0: selected fe:2c:91:68:29:2b addr=48977 dist=65460
1.178 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 1: selected fe:81:ab:c5:e3:03 addr=49181 dist=65256
1.809 batadv:batadv_dbg:batman_adv bat0 dat_select_candidates() 2: selected 66:25:a7:48:37:fb addr=49328 dist=65109
1.828 batadv:batadv_dbg:batman_adv bat0 DHT_SEND for 10.204.32.1
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
CONFIG_BATMAN_ADV_DEBUGFS is disabled by default because debugfs is not
supported for batman-adv interfaces in any non-default netns. Any remaining
users of this interface should still be informed about the deprecation and
the generic netlink alternative.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The hardif_neigh refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The backbone_gw refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_tvlv_handler_register is responsible for adding new
tvlv_handler to the handler_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: ef26157747 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_tt_global_orig_entry_add is responsible for adding new
tt_orig_list_entry to the orig_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d657e621a0 ("batman-adv: add reference counting for type batadv_tt_orig_list_entry")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_nc_get_nc_node is responsible for adding new nc_nodes
to the in_coding_list and out_coding_list. It first checks whether the
entry already is in the list or not. If it is, then the creation of a new
entry is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: d56b1705e2 ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/elp_interval" is using the generic
functions to store/show uint values. The helper __batadv_store_uint_attr
requires the softif net_device as parameter to print the resulting change
as info text when the users writes to this file. It uses the helper
function batadv_info to add it at the same time to the kernel ring buffer
and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0744ff8fa8 ("batman-adv: Add hard_iface specific sysfs wrapper macros for UINT")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The per hardif sysfs file "batman_adv/throughput_override" prints the
resulting change as info text when the users writes to this file. It uses
the helper function batadv_info to add it at the same time to the kernel
ring buffer and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG
is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes: 0b5ecc6811 ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The probe ELPs for WiFi interfaces are expanded to contain at least
BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the
number of bytes which the template ELP packet requires.
These extra padding bytes were not initialized and thus could contain data
which were previously stored at the same location. It is therefore required
to set it to some predefined or random values to avoid leaking private
information from the system transmitting these kind of packets.
Fixes: e4623c913508 ("batman-adv: Avoid probe ELP information leak")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=dmZo
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180717' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann
- Enable DAT by default at compile time, by Antonio Quartulli
- Remove obsolete default n in Kconfig, by Sven Eckelmann
- Fix checkpatch spelling errors, by Sven Eckelmann
- Unify header guards style, by Sven Eckelmann
- Consolidate batadv_purge_orig functions, by Sven Eckelmann
- Replace type define with proper typedef, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The #define for batadv_dat_addr_t is doing nothing else than giving u16 a
new typename. But C already has the special keyword "typedef" which is also
better supported by kernel-doc.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The single line function batadv_purge_orig_ref has no function beside
providing the name used by other source files. This can also be done
simpler by just renaming _batadv_purge_orig to batadv_purge_orig_ref.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All other include guards in batman-adv use the style:
* _NET_BATMAN_ADV_$(FILENAME)_
* uppercase only
* "." & "-" replaced with "_"
Use this also in the B.A.T.M.A.N. IV/V OGM implementation headers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
commit a2d4df9b673c ("spelling.txt: add more spellings to spelling.txt")
introduced the spellcheck of "cache" for checkpatch.pl.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "default n" is the default value for any bool or tristate Kconfig
setting. It is therefore not necessary to add it to a config entry.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
DAT (Distributed ARP Table) has been enabled by default
in the out-of-tree batman-adv kernel module for several
years already.
It can now be enabled in the kernel too.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The Kconfig option BATMAN_ADV_BATMAN_V is now enabled by default when the
BATMAN_ADV is enabled. A feature which is enabled by default for a module
should not be considered experimental.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a (broken) node wrongly sends multicast TT entries with a ROAM
flag then this causes any receiving node to drop all entries for the
same multicast MAC address announced by other nodes, leading to
packet loss.
Fix this DoS vector by only storing TT sync flags. For multicast TT
non-sync'ing flag bits like ROAM are unused so far anyway.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Since commit 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
TT sync flags and TT non-sync'd flags are supposed to be stored
separately.
The previous patch missed to apply this separation on a TT entry with
only a single TT orig entry.
This is a minor fix because with only a single TT orig entry the DDoS
issue the former patch solves does not apply.
Fixes: 54e22f265e ("batman-adv: fix TT sync flag inconsistencies")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is creating special debugfs directories in the init
net_namespace for each created soft-interface (batadv net_device). But it
is possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new batadv net_device with
the name "bat0". batman-adv is then also adding a new directory under
$debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "bat1" and registers a
different batadv device with the name "bat0". batman-adv will then try to
create a directory with the name "bat0" under $debugfs/batman-adv/ again.
But there already exists one with this name under this path and thus this
fails. batman-adv will detect a problem and rollback the registering of
this device.
batman-adv must therefore take care of renaming the debugfs directories for
soft-interfaces whenever it detects such a net_device rename.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is creating special debugfs directories in the init
net_namespace for each valid hard-interface (net_device). But it is
possible to rename a net_device to a completely different name then the
original one.
It can therefore happen that a user registers a new net_device which gets
the name "wlan0" assigned by default. batman-adv is also adding a new
directory under $debugfs/batman-adv/ with the name "wlan0".
The user then decides to rename this device to "wl_pri" and registers a
different device. The kernel may now decide to use the name "wlan0" again
for this new device. batman-adv will detect it as a valid net_device and
tries to create a directory with the name "wlan0" under
$debugfs/batman-adv/. But there already exists one with this name under
this path and thus this fails. batman-adv will detect a problem and
rollback the registering of this device.
batman-adv must therefore take care of renaming the debugfs directories
for hard-interfaces whenever it detects such a net_device rename.
Fixes: 5bc7c1eb44 ("batman-adv: add debugfs structure for information per interface")
Reported-by: John Soros <sorosj@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_v_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: b71bb6f924 ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_iv_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Virtual interface drivers such as tun / tap interfaces, VLAN, etc tend
to initialize the interface throughput with some value for the sake of
having a throughput number to export via ethtool. This exported
throughput leaves batman-adv to conclude the interface throughput is
genuine (reflecting reality), thus no measurements are necessary.
Based on the observation that those interface types also tend to set
the link auto-negotiation to 'off', batman-adv shall check this
setting to differentiate between genuine link throughput information
and placeholders installed by virtual interfaces.
The "default throughput" setting exported via sysfs still allows to
configure the batman-adv throughput for the interface, thus disabling
the measurements.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A translation table TVLV changset sent with an OGM consists
of a number of headers (one per VLAN) plus the changeset
itself (addition and/or deletion of entries).
The per-VLAN headers are used by OGM recipients for consistency
checks. Said consistency check might determine that a full
translation table request is needed to restore consistency. If
the TT sender adds per-VLAN headers of empty VLANs into the OGM,
recipients are led to believe to have reached an inconsistent
state and thus request a full table update. The full table does
not contain empty VLANs (due to missing entries) the cycle
restarts when the next OGM is issued.
Consequently, when the translation table TVLV headers are
composed, empty VLANs are to be excluded.
Fixes: 21a57f6e7a3b ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The previous TT sync fix so far only fixed TT responses issued by the
target node directly. So far, TT responses issued by intermediate nodes
still lead to the wrong flags being added, leading to CRC mismatches.
This behaviour was observed at Freifunk Hannover in a 800 nodes setup
where a considerable amount of nodes were still infected with 'WI'
TT flags even with (most) nodes having the previous TT sync fix applied.
I was able to reproduce the issue with intermediate TT responses in a
four node test setup and this patch fixes this issue by ensuring to
use the per originator instead of the summarized, OR'd ones.
Fixes: e9c00136a4 ("batman-adv: fix tt_global_entries flags update")
Reported-by: Leonardo Mörlein <me@irrelefant.net>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The functions batadv_tt_prepare_tvlv_local_data and
batadv_tt_prepare_tvlv_global_data are responsible for preparing a buffer
which can be used to store the TVLV container for TT and add the VLAN
information to it.
This will be done in three phases:
1. count the number of VLANs and their entries
2. allocate the buffer using the counters from the previous step and limits
from the caller (parameter tt_len)
3. insert the VLAN information to the buffer
The step 1 and 3 operate on a list which contains the VLANs. The access to
these lists must be protected with an appropriate lock or otherwise they
might operate on on different entries. This could for example happen when
another context is adding VLAN entries to this list.
This could lead to a buffer overflow in these functions when enough entries
were added between step 1 and 3 to the VLAN lists that the buffer room for
the entries (*tt_change) is smaller then the now required extra buffer for
new VLAN entries.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
[sven@narfation.org: fixed alignment]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The debug_dir variable in the main structures is only accessed when
CONFIG_BATMAN_ADV_DEBUGFS is enabled. It can be dropped to potentially save
some bytes of memory.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Using the bool type for structure member is considered inappropriate [1]
for the kernel. Its size is not well defined (but usually 1 byte but maybe
also 4 byte).
[1] https://lkml.org/lkml/2017/11/21/384
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of disabling multicast optimizations mesh-wide once a node with
no multicast optimizations capabilities joins the mesh, do the
following:
Just insert such nodes into the WANT_ALL_IPV4/IPV6 lists. This is
sufficient to avoid multicast packet loss to such unsupportive nodes.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All tools which were known to the batman-adv development team are
supporting the batman-adv netlink interface since a while. Also debugfs is
not supported for batman-adv interfaces in any non-default netns. Thus
disabling CONFIG_BATMAN_ADV_DEBUGFS by default should not cause problems on
most systems. It is still possible to enable it in case it is still
required in a specific setup.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In the case where hard_iface is NULL, the error path may pass a null
pointer to batadv_hardif_put causing a null pointer dereference error.
Avoid this by only calling the function if hard_iface not null.
Detected by CoverityScan, CID#1466456 ("Explicit null dereferenced")
Fixes: 53dd9a68ba ("batman-adv: add multicast flags netlink support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
DHCP connectivity issues can currently occur if the following conditions
are met:
1) A DHCP packet from a client to a server
2) This packet has a multicast destination
3) This destination has a matching entry in the translation table
(FF:FF:FF:FF:FF:FF for IPv4, 33:33:00:01:00:02/33:33:00:01:00:03
for IPv6)
4) The orig-node determined by TT for the multicast destination
does not match the orig-node determined by best-gateway-selection
In this case the DHCP packet will be dropped.
The "gateway-out-of-range" check is supposed to only be applied to
unicasted DHCP packets to a specific DHCP server.
In that case dropping the the unicasted frame forces the client to
retry via a broadcasted one, but now directed to the new best
gateway.
A DHCP packet with broadcast/multicast destination is already ensured to
always be delivered to the best gateway. Dropping a multicasted
DHCP packet here will only prevent completing DHCP as there is no
other fallback.
So far, it seems the unicast check was implicitly performed by
expecting the batadv_transtable_search() to return NULL for multicast
destinations. However, a multicast address could have always ended up in
the translation table and in fact is now common.
To fix this potential loss of a DHCP client-to-server packet to a
multicast address this patch adds an explicit multicast destination
check to reliably bail out of the gateway-out-of-range check for such
destinations.
The issue and fix were tested in the following three node setup:
- Line topology, A-B-C
- A: gateway client, DHCP client
- B: gateway server, hop-penalty increased: 30->60, DHCP server
- C: gateway server, code modifications to announce FF:FF:FF:FF:FF:FF
Without this patch, A would never transmit its DHCP Discover packet
due to an always "out-of-range" condition. With this patch,
a full DHCP handshake between A and B was possible again.
Fixes: be7af5cf9c ("batman-adv: refactoring gateway handling code")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
For multicast frames AP isolation is only supposed to be checked on
the receiving nodes and never on the originating one.
Furthermore, the isolation or wifi flag bits should only be intepreted
as such for unicast and never multicast TT entries.
By injecting flags to the multicast TT entry claimed by a single
target node it was verified in tests that this multicast address
becomes unreachable, leading to packet loss.
Omitting the "src" parameter to the batadv_transtable_search() call
successfully skipped the AP isolation check and made the target
reachable again.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- avoid redundant multicast TT entries, by Linus Luessing
- add netlink support for distributed arp table cache and multicast flags,
by Linus Luessing (2 patches)
-----BEGIN PGP SIGNATURE-----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=HVxO
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180319' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- avoid redundant multicast TT entries, by Linus Luessing
- add netlink support for distributed arp table cache and multicast flags,
by Linus Luessing (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Checking for 0 is insufficient: when an SKB without a batadv header, but
with a VLAN header is received, hdr_size will be 4, making the following
code interpret the Ethernet header as a batadv header.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_check_unicast_ttvn() calls skb_cow(), so pointers into the SKB data
must be (re)set after calling it. The ethhdr variable is dropped
altogether.
Fixes: 7cdcf6dddc ("batman-adv: add UNICAST_4ADDR packet type")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Dump the list of multicast flags entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Dump the list of DAT cache entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a node signals that it wants all traffic for a specific protocol
family then there is no need to announce individual multicast addresses
via TT.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
As the kernel doc describes too the code is supposed to skip adding
multicast TT entries if both the WANT_ALL_IPV4 and WANT_ALL_IPV6 flags
are present.
Unfortunately, the current code even skips adding multicast TT entries
if only either the WANT_ALL_IPV4 or WANT_ALL_IPV6 is present.
This could lead to IPv6 multicast packet loss if only an IGMP but not an
MLD querier is present for instance or vice versa.
Fixes: 687937ab34 ("batman-adv: Add multicast optimization support for bridged setups")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
commit 785ea11441 ("batman-adv: Distributed ARP Table - create DHT helper
functions") introduced a return check of batadv_compare_eth which uses a
boolean return value since commit 16af73458aca ("batman-adv: main,
batadv_compare_eth return bool"). A relational (<, >, <= or >=) operator
is not the right one for such a check.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Also multiline macros should have their statements start on a tabstop. This
was detected by checkpatch.pl after commit a134f8de9f ("checkpatch:
improve the TABSTOP test to include declarations").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv uses internal indices for each enabled and active interface.
It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the
correct position in the ogm_cnt bitmaps.
The type for the number of enabled interfaces (which defines the next
interface index) was set to char. This type can be (depending on the
architecture) either signed (limiting batman-adv to 127 active slave
interfaces) or unsigned (limiting batman-adv to 255 active slave
interfaces).
This limit was not correctly checked when an interface was enabled and thus
an overflow happened. This was only catched on systems with the signed char
type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with
a negative size.
The if_num interface index was only a s16 and therefore significantly
smaller than the ifindex (int) used by the code net code.
Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be
(unsigned) int to support the same number of slave interfaces as the net
core code. And the interface activation code must check the number of
active slave interfaces to avoid integer overflows.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_bla_backbone_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: ea4152e117 ("batman-adv: add backbone table netlink support")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.
But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.
And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.
Fixes: 04f3f5bf18 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: b71bb6f924 ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.
Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uapi headers use the __u8/__u16/... version of the fixed width types
instead of u8/u16/... The use of the latter must be avoided before
packet.h is copied to include/uapi/linux/.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BIT(x) macro is no longer available for uapi headers because it is
defined outside of it (linux/bitops.h). The use of it must therefore be
avoided and replaced by an appropriate other representation.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The headers used by packet.h should also be included by it directly. main.h
is currently dealing with it in batman-adv, but this will no longer work
when this header is moved to include/uapi/linux/.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
-----BEGIN PGP SIGNATURE-----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=5JUK
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20171220' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the kernel-doc documentation, externally visible functions
should be documented. This refers to all all non-static function which can
(and will) be used by functions in other sources files.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Externally visible functions should be documented with kernel-doc. This
usually refers to non-static functions but also static inline files in
headers are visible in other files and should therefore be documented.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All enums in types.h are already documented. But some other headers
still have private enums which also should be documented.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All structs in types.h are already documented. But some other headers
still have private structs which also should be documented.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The correct syntax to create references in kernel-doc to a struct member is
not "struct_name::member"" but "&struct_name->member" or
"&struct_name.member". The correct syntax is required to get the correct
cross-referencing in the reStructuredText text output.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The inline kernel-doc comments make it easier to keep changes to the
struct/enum synchronized with the documentation of the it. And it makes it
easier for larger structures like struct batadv_priv to read the
documentation inside the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/wait.h include was removed with commit 421d988b2c08 ("batman-adv:
Consolidate logging related functions"). The previously required (but not
unused) linux/sched.h include can also be dropped now.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/kobject.h provides the kobject_* function declarations and should
therefore be included directly before they are used.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/net.h provides the net_ratelimited_function. It should
therefore be included directly before it is used.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
commit bc6245e5ef ("bug: split BUILD_BUG stuff out into
<linux/build_bug.h>") added a new header for BUILD_BUG_ON. It should
therefore be included instead of linux/bug.h
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The last remaining file without license notice and/or SPDX license
identifier under net/batman-adv/ is the Kconfig. It should have been
licensed under the same conditions as the rest of batman-adv and the
Makefile which uses the CONFIG_* variables from Kconfig.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This function compiles to 288 bytes of machine code for Linux 4.14 on
Debian Stretch amd64 and (6.3.0-18) with the default configuration. 27
callsites (25 used in default config).
text data bss dec hex filename
179291 10317 4416 194024 2f5e8 batman-adv.ko.pre
171952 10317 4416 186685 2d93d batman-adv.ko.post
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
[sven@narfation.org: Fix includes, correct sizes+counts in commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The originator node object orig_neigh_node is used to when accessing the
bcast_own(_sum) and real_packet_count information. The access to them has
to be protected with the spinlock in orig_neigh_node.
But the function uses the lock in orig_node instead. This is incorrect
because they could be two different originator node objects.
Fixes: 0ede9f41b2 ("batman-adv: protect bit operations to count OGMs with spinlock")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit e99e88a9d2 ("treewide: setup_timer() -> timer_setup()")
changed the argument name and type of the timer function but didn't adjust
the kernel-doc of these functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_v_gw_is_eligible function already assumes that orig_node is not
NULL. But batadv_gw_node_get may have failed to find the originator. It
must therefore be checked whether the batadv_gw_node_get failed and not
whether orig_node is NULL to detect this error.
Fixes: 50164d8f50 ("batman-adv: B.A.T.M.A.N. V - implement GW selection logic")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv unuicast fragment header contains 3 bits for the priority of
the packet. These bits will be initialized when the skb->priority contains
a value between 256 and 263. But otherwise, the uninitialized bits from the
stack will be used.
Fixes: c0f25c802b ("batman-adv: Include frame priority in fragment header")
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The neighbor compare API implementation for B.A.T.M.A.N. V checks whether
the neigh_ifinfo for this neighbor on a specific interface exists. A
warning is printed when it isn't found.
But it is not called inside a lock which would prevent that this
information is lost right before batadv_neigh_ifinfo_get. It must therefore
be expected that batadv_v_neigh_(cmp|is_sob) might not be able to get the
requested neigh_ifinfo.
A WARN_ON for such a situation seems not to be appropriate because this
will only flood the kernel logs. The warnings must therefore be removed.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The parameter extack was added to batadv_softif_slave_add without adding
the kernel-doc for it. This caused kernel-doc warnings.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich
- Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
-----BEGIN PGP SIGNATURE-----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=7hcv
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20171006' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Eckelmann