Update CFG_1US_TIMER_TRSH and CON_CFG_DRIVER settings.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The init is missed for hisi_sas_phy spinlock, so add it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver spends much time allocating and freeing the slot DMA
buffer for command delivery/completion. To boost the performance,
pre-allocate the buffers for all IPTT. The downside of this approach is
that we are reallocating all buffer memory upfront, so hog memory which we
may not need.
However, the current method - DMA buffer pool - also caches all buffers and
does not free them until the pool is destroyed, so is not exactly efficient
either.
On top of this, since the slot DMA buffer is slightly bigger than a 4K
page, we need to allocate 2x4K pages per buffer (for 4K page kernel), which
is quite wasteful. For 64K page size this is not such an issue.
So, for the 4K page case, in order to make memory usage more efficient,
pre-allocating larger blocks of DMA memory for the buffers can be more
efficient.
To make DMA memory usage most efficient, we would choose a single
contiguous DMA memory block, but this could use up all the DMA memory in
the system (when CMA enabled and no IOMMU), or we may just not be able to
allocate a DMA buffer large enough when no CMA or IOMMU.
To decide the block size we use the LCM (least common multiple) of the
buffer size and the page size. We roundup(64) to ensure the LCM is not too
large, even though a little memory may be wasted per block.
So, with this, the total memory requirement is about is about 17MB for 4096
max IPTT.
Previously (for 4K pages case), it would be 32MB (for all slots
allocated).
With this change, the relative increase of IOPS for bs=4K read when
PAGE_SIZE=4K and PAGE_SIZE=64K is as follows:
IODEPTH 4K PAGE_SIZE 64K PAGE_SIZE
32 56% 47%
64 53% 44%
128 64% 43%
256 67% 45%
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In host reset, we use TMF or soft-reset to re-init device, and if success,
we will release all LLDD resources of this device. If the init fails -
maybe because the device was removed or link has not come up - then do not
release the LLDD resources, but rather rely on SCSI EH to handle the
timeout for these resources later on.
But if clear nexus ha calls host reset, which is the last effort of SCSI
EH, we should release all LLDD remain resources. Because SCSI EH will
release all tasks after clear nexus ha.
Before release, we do I_T nexus reset to try to clear target remain IOs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During reset, we don't want PHY events reported to libsas for PHYs which
were previously attached prior to reset.
So check hisi_hba->flags for HISI_SAS_RESET_BIT to filter PHY events during
reset.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After soft_reset() for host reset, we should not be allowed to send
commands to the HW before the PHYs have come up and the port ids have been
refreshed.
Prior to this point, any commands cannot be successfully completed.
This exclusion is achieved by grabbing the host reset semaphore.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possible conflict when a device is removed and host reset occurs
concurrently.
The reason is that then the device is notified as gone, we try to clear the
ITCT, which is notified via an interrupt. The dev gone function pends on
this event with a completion, which is completed when the ITCT interrupt
occurs.
But host reset will disable all interrupts, the wait_for_completion() may
wait indefinitely.
This patch adds an semaphore to synchronise this two processes. The
semaphore is taken by the host reset as the basis of synchronising.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are many BROADCAST primitives generated by the host. We are only
interested in BROADCAST (CHANGE) primitives currently, so only process
this.
We have applied this processing for v2 hw before, and it is also needed for
v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch replaces the usage of dma_alloc_coherent() with the managed
version, dmam_alloc_coherent(), hereby reducing replicated code.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by; John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware provides drive specific target reset and task abort timeout
values. Driver needs to use these timeout values during task management
calls. If FW does not provide these values, fall back to using earlier
default timeout of 50 seconds for TM.
[mkp: clarified comment]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While driver is waiting for adapter to become operational, if a kill
adapter is issued, driver can bail out from the wait loop immediately
rather than waiting for the entire 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If MR_DCMD_CTRL_GET_INFO DCMD timed out, return failure rather than doing
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to "26.100.00.00"
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently driver is using combined reply queue feature when MSI-x vectors >
8 for both SAS3 and SAS3.5 controllers. But as per MPI-spec,
1. For SAS3 controllers, driver should use combined reply queue when HBA
supports more than 8 MSI-x vectors.
2. For SAS3.5 controllers, driver should use combined reply queue when HBA
supports more than 16 MSI-x vectors.
Modified driver code to use combined reply queue for SAS3 controllers when
HBA supports > 8 MSI-x vectors and for SAS3.5 controllers when HBA supports
> 16 MSI-x vectors.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While configuring of NVMe device handling, _pcie_device structure member
was accessed after its reference count is decremented/put. Hence modified
code to access member of _pcie_device structure before its reference count
is decremented/put.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_scan_finished driver should mark port_enable_cmd.status as
'command not used', instead base_cmds.status was marked as 'command not
used'. Update code to mark port_enable_cmd.status as 'command not used'.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux driver when receives Broadcast Asynchronous Event Notification (BAEN)
from the controller firmware, checks all pending I/Os at the driver level
and issues query task, abort task TMs. This is done in the driver to handle
drives which are connected with multiple initiators and undergoing target
resets. In the BAEN handling code, the I/Os issued to NVMe drives are also
handled and query task and abort task TMs are issued, which are not
necessary as there is no multi-initiator and no BAEN concept with NVMe
drives. Hence when the driver checks for pending I/Os it skips NVMe drives
at this moment.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWyHBVCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTkjAPoDF71y
5+w0pim7HQvyo02GxKRWyYzkibZsTfNQ49Yo6wD9EhKp1OD4TIrO1ey3fHpCcYry
CHfUIClnev6hiqDBDrI=
=xJ+K
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Mask off Scope bits in retry delay
scsi: qla2xxx: Fix crash on qla2x00_mailbox_command
scsi: aic7xxx: aic79xx: fix potential null pointer dereference on ahd
scsi: mpt3sas: Add an I/O barrier
scsi: qla2xxx: Fix setting lower transfer speed if GPSC fails
scsi: hpsa: disable device during shutdown
scsi: sd_zbc: Fix sd_zbc_check_zone_size() error path
scsi: aacraid: remove bogus GFP_DMA32 specifies
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
Some newer target uses "Status Qualifier" response in a returned "Busy
Status". This new response code of 0x4001, which is "Scope" bits,
translates to "Affects all units accessible by target". Due to this new
value returned in the Scope bits, driver was using that value as timeout
value which resulted into driver waiting for 27min timeout.
This patch masks off this Scope bits so that driver does not use this
value as retry delay time.
Cc: <stable@vger.kernel.org>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a crash on qla2x00_mailbox_command caused when the driver
is on UNLOADING state and tries to call qla2x00_poll, which triggers a
NULL pointer dereference.
Signed-off-by: Rodrigo R. Galvao <rosattig@linux.vnet.ibm.com>
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If AHD_DEBUG is enabled and ahd_platform_alloc fails then ahd is set to
null and the debug printk dereferences ahd when passing it to ahd_name.
Fix this by moving the debug printk to before the call to
ahd_platform_alloc where ahd is not null at that point.
Detected by CoverityScan, CID#100296 ("Explicit null dereference")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prevents driver from setting lower default speed of 1 GB/sec,
if the switch does not support Get Port Speed Capabilities (GPSC)
command. Setting this default speed results into much lower write
performance for large sequential WRITE. This patch modifies driver to
check for gpsc_supported flags and prevents driver from issuing
MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver
does not send this mailbox command, firmware assumes maximum supported
link speed and will operate at the max speed.
Cc: stable@vger.kernel.org
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reported-by: Eda Zhou <ezhou@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'Commit cc27b735ad ("PCI/portdrv: Turn off PCIe services during
shutdown")' has been added to kernel to shutdown pending PCIe port service
interrupts during reboot so that a newly started kexec kernel wouldn't
observe pending interrupts.
pcie_port_device_remove() is disabling the root port and switches by
calling pci_disable_device() after all PCIe service drivers are shutdown.
This has been found to cause crashes on HP DL360 Gen9 machines during
reboot due to hpsa driver not clearing the bus master bit during the
shutdown procedure by calling pci_disable_device().
Disable device as part of the shutdown sequence.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199779
Fixes: cc27b735ad ("PCI/portdrv: Turn off PCIe services during shutdown")
Cc: stable@vger.kernel.org
Reported-by: Ryan Finnie <ryan@finnie.org>
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a drive with variable zone sizes or an invalid last zone size is
detected, the local variable this_zone_blocks is set to 0 and early return
from the function triggered, but this does not result in an error return.
The local variable zone_blocks must be set to 0 for an error to be
returned.
[mkp: typo in commit description]
Fixes: ccce20fc79 ("scsi: sd_zbc: Avoid that resetting a zone fails sporadically")
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For one GFP_DMA32 does not actually work with kmalloc, as we only have
GFP_DMA and GFP_KERNEL caches, but not GFP_DMA32. Second the memory
is mapped using the proper DMA API anyway, which would include proper
bounce buffering if needed by the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eve of merge window fix: The original code was so bogus as to be
casting the wrong generic device to an rport and proceeding to take
actions based on the bogus values it found. Fortunately it seems the
location that is dereferenced always exists, so the code hasn't oopsed
yet, but it certainly annoys the memory checkers.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWxMJDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWkTAP0QPfpP
ywyhrODRRPNg73zZnF3qo3CSeswSxDdjyW/4JAD/aLgTfPOydD+EA/sr/hjcs+Z/
DU3lt68c+CVp1kRtZ9A=
=9sLD
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Eve of merge window fix: The original code was so bogus as to be
casting the wrong generic device to an rport and proceeding to take
actions based on the bogus values it found.
Fortunately it seems the location that is dereferenced always exists,
so the code hasn't oopsed yet, but it certainly annoys the memory
checkers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_srp: Fix shost to rport translation
Bsg holding a reference to the parent device may result in a crash if a
bsg file handle is closed after the parent device driver has unloaded.
Holding a reference is not really needed: the parent device must exist
between bsg_register_queue and bsg_unregister_queue. Before the device
goes away the caller does blk_cleanup_queue so that all in-flight
requests to the device are gone and all new requests cannot pass beyond
the queue. The queue itself is a refcounted object and it will stay
alive with a bsg file.
Based on analysis, previous patch and changelog from Anatoliy Glagolev.
Reported-by: Anatoliy Glagolev <glagolig@gmail.com>
Reviewed-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
libiscsi is the only SCSI code that return BLK_EH_HANDLED, thus trying to
bypass the normal SCSI EH code. We are going to remove this return value
at the block layer, and at least from a quick look it doesn't look too
harmful to try to send an abort for these cases, especially as the first
one should not actually be possible. If this doesn't work out iscsi
will probably need its own eh_strategy_handler instead to just do the
right thing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BLK_EH_NOT_HANDLED implies nothing happen, but very often that
is not what is happening - instead the driver already completed the
command. Fix the symbolic name to reflect that a little better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
John Garry