This is an ugly one unfortunately. Currently, all DRM drivers supporting
atomic modesetting will save the state that userspace had set before
suspending, then attempt to restore that state on resume. This probably
worked very well at one point, like many other things, until DP MST came
into the picture. While it's easy to restore state on normal display
connectors that were disconnected during suspend regardless of their
state post-resume, this can't really be done with MST because of the
fact that setting up a downstream sink requires performing sideband
transactions between the source and the MST hub, sending out the ACT
packets, etc.
Because of this, there isn't really a guarantee that we can restore the
atomic state we had before suspend once we've resumed. This sucks pretty
bad, but so far I haven't run into any compositors that this actually
causes serious issues with. Most compositors will notice the hotplug we
send afterwards, and then reprobe state.
Since nouveau and i915 also don't fail the suspend/resume process due to
failing to restore the atomic state, let's make amdgpu match this
behavior. Better to resume the GPU properly, then to stop the process
half way because of a potentially unavoidable atomic commit failure.
Eventually, we'll have a real fix for this problem on the DRM level. But
we've got some more important low-hanging fruit to deal with first.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.com
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcL65eAAoJEAx081l5xIa+y7EP+wQnTk3GV7rKiIi5LEtux5xW
X2tTaPKHnwrMYjRaP2VNUntJPH6Wxcby3OHGNvGMe1IqNGL/5qRLQ/g1rSSPuM4z
rYwWR/ooDU/KwYvsT/o+DSO62AoVzIqx8gn8+ShirRN3MdobCcwDebd5oqKjduOn
hRy9WQwgPOnDG1D3fRWOGSzOE1K9yDFCUaR0AmhUehn9NvsztQGamMBBwMNg+y52
a5vu+nSLxQrv3ZyZ5TQUgAzi2pWFtC6QxIVuLpl5TqFA3vdRVyN1T78klDnQ7WU7
6GY1yq9D923c1Tfa0RZoXnE++bX91KKJ5y9YFuNFv8X/th6UoEzRrOPDINfLoZv3
JsPPSPAiZTgoXc/RGfoMbnidajNB7Gx+No+Pd8P6MeY5H1E+ivMXt5MrOgcMXUqk
FajthiuSlaB+u5OjNjuS6gBbAMIKw7Idg4hEFSabj91qhJIet/fPhzNmp0HPJ1wF
XlNnxI7XOytCAORrjLy2q4/lkaoG2AlVpZzeMLgXSxGGlSCtIpDUIqgQbtV1ppCi
RboQ8yMflRejeK6oXoC92mI8yDB6rwoQy2tK0Hvnag5/q1r7AVYJq+3890NFEU4X
F5TuCgvhswdkTEJUED1G6pnX7aQzW0dh6KrCltF34sFzD1etYb150En7laa+2kmX
G5HfZbkLwscPt91moA6B
=hFld
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mmu notifier contextual informations", v2.
This patchset adds contextual information, why an invalidation is
happening, to mmu notifier callback. This is necessary for user of mmu
notifier that wish to maintains their own data structure without having to
add new fields to struct vm_area_struct (vma).
For instance device can have they own page table that mirror the process
address space. When a vma is unmap (munmap() syscall) the device driver
can free the device page table for the range.
Today we do not have any information on why a mmu notifier call back is
happening and thus device driver have to assume that it is always an
munmap(). This is inefficient at it means that it needs to re-allocate
device page table on next page fault and rebuild the whole device driver
data structure for the range.
Other use case beside munmap() also exist, for instance it is pointless
for device driver to invalidate the device page table when the
invalidation is for the soft dirtyness tracking. Or device driver can
optimize away mprotect() that change the page table permission access for
the range.
This patchset enables all this optimizations for device drivers. I do not
include any of those in this series but another patchset I am posting will
leverage this.
The patchset is pretty simple from a code point of view. The first two
patches consolidate all mmu notifier arguments into a struct so that it is
easier to add/change arguments. The last patch adds the contextual
information (munmap, protection, soft dirty, clear, ...).
This patch (of 3):
To avoid having to change many callback definition everytime we want to
add a parameter use a structure to group all parameters for the
mmu_notifier invalidate_range_start/end callback. No functional changes
with this patch.
[akpm@linux-foundation.org: fix drivers/gpu/drm/amd/amdgpu/amdgpu_mn.c kerneldoc]
Link: http://lkml.kernel.org/r/20181205053628.3210-2-jglisse@redhat.com
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Jason Gunthorpe <jgg@mellanox.com> [infiniband]
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <zwisler@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
totalram_pages, zone->managed_pages and totalhigh_pages updates are
protected by managed_page_count_lock, but readers never care about it.
Convert these variables to atomic to avoid readers potentially seeing a
store tear.
This patch converts zone->managed_pages. Subsequent patches will convert
totalram_panges, totalhigh_pages and eventually managed_page_count_lock
will be removed.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
Link: http://lkml.kernel.org/r/1542090790-21750-3-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PSP ASD firmware loading on Vega20. Not sure why
this was missing before.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resolves __udivdi3 missing errors when building for i386.
Fixes: 6378ef012ddc ("drm/amd/display: Add below the range support for FreeSync")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since umr tool can't handle bracket, change uvd ring name convention.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support manual LCLK DPM level switch on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When a job is timeout, try to print the related process information
for debugging
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
passive update planes still spends a litte more
time on some cases.
[How]
Remove unnecessary trace which involving in some register read.
Disable debug output for release build.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP LL CTS1.4 4.3.2.1 test failure.
[how]
The failure is caused by not handling DP link loss
hpd short pusle during set mode. The change is to read link status
before set mode link training. If link is lost, re-verify link caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently, when the VSP infopacket is rebuilt in DM, it is not updated
when being programmed in encoder.
[HOW]
Add new VSP case for update_info_frame
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.
[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.
[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.
This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout. Most of the time it isn't
a real issue.
[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.
[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.
[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.
In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need a way to differentiate Vega 20 in DC
[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the flip-rate is below the minimum supported variable refresh rate
range for the monitor the front porch wait will timeout and be
frequently misaligned resulting in stuttering and/or flickering.
The FreeSync module can still maintain a smooth and flicker free
image when the monitor has a refresh rate range such that the maximum
refresh > 2 * minimum refresh by utilizing low framerate compensation,
"below the range".
[How]
Hook up the pre-flip and post-flip handlers from the FreeSync module.
These adjust the minimum/maximum vrr range to duplicate frames
when appropriate by tracking flip timestamps.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value observed on some
systems
[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The behavior of drm_atomic_helper_cleanup_planes differs depending on
whether the commit was asynchronous or not. When it's called from
amdgpu_dm_atomic_commit_tail during a typical atomic commit the
plane state has been swapped so it calls cleanup_fb on the old plane
state.
However, in the asynchronous commit codepath the call to
drm_atomic_helper_commit also calls dm_plane_helper_cleanup_fb after
atomic_async_update has been called. Since the plane state is updated
in place and has not been swapped the cleanup_fb call affects the new
plane state.
This results in a use after free for the given sequence:
- Fast update, fb1 pin/ref, fb1 unpin/unref
- Fast update, fb2 pin/ref, fb2 unpin/unref
- Slow update, fb1 pin/ref, fb2 unpin/unref
- Fast update, fb2 pin/ref -> use after free. bug
[How]
Disallow framebuffer changes in the fast path. Since this includes
a NULL framebuffer, this means that only framebuffers that have
been previously pin+ref at least once will be used, preventing a
use after free.
This has a significant throughput reduction for cursor updates where
the framebuffer changes. For most desktop usage this isn't a problem,
but it does introduce performance regressions for two specific IGT
tests:
- cursor-vs-flip-toggle
- cursor-vs-flip-varying-size
Fixes: 2cc751931afc ("drm/amd/display: Add fast path for cursor plane updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should not return 0 for error case as '0' is actually
a special value for index.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On errors, dma_buf_get returns a negative error code, rather than NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If register value is updating, reset timeout counter.
It improves robustness of SOC15_WAIT_ON_RREG.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove bit 31 for scratch2 to indicate the Hardware bug work around is active.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scan enc/jpeg fences to init dpg pause new state in begin use.
It will help set dpg mode to desire state actively.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always check all vcn ring status during dpg mode stop, it will help
identify which vcn ring may cause the issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is a bug fix.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under Dynamic Power Gate mode, UVD_STATUS needn't be checked.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It indicates a pin/unpin imbalance bug somewhere. While the bug isn't
necessarily in the call chain hitting this, it's at least one part
involved.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Page queue is supported on Vega20 with SDMA firmware
123 onwards.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Vega20 uses ring id 1 for page queues EOP irq while previous
ASICs take ring id 3.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need new invalidation engine layout due to new SDMA page
queues added.
V2: fix coding style and add correct return value
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As two more SDMA page queue rings are added on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the fence is already signaled it is perfectly normal to get a NULL
fence here. But since we can't export that we need to use a stub fence.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently driver only psp v11 support vmr.
v2: squash in unused variable removal (Alex)
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If PSP FW is running already, driver will not load PSP FW again and skip
it. So psp fw version is not correct if reading it from FW binary file,
need to get right version from register.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude Paul