Most hw_random devices return entropy which is assumed to be of full
quality, but driver authors don't bother setting the quality knob. Some
hw_random devices return less than full quality entropy, and then driver
authors set the quality knob. Therefore, the entropy crediting should be
opt-out rather than opt-in per-driver, to reflect the actual reality on
the ground.
For example, the two Raspberry Pi RNG drivers produce full entropy
randomness, and both EDK2 and U-Boot's drivers for these treat them as
such. The result is that EFI then uses these numbers and passes the to
Linux, and Linux credits them as boot, thereby initializing the RNG.
Yet, in Linux, the quality knob was never set to anything, and so on the
chance that Linux is booted without EFI, nothing is ever credited.
That's annoying.
The same pattern appears to repeat itself throughout various drivers. In
fact, very very few drivers have bothered setting quality=1024.
Looking at the git history of existing drivers and corresponding mailing
list discussion, this conclusion tracks. There's been a decent amount of
discussion about drivers that set quality < 1024 -- somebody read and
interepreted a datasheet, or made some back of the envelope calculation
somehow. But there's been very little, if any, discussion about most
drivers where the quality is just set to 1024 or unset (or set to 1000
when the authors misunderstood the API and assumed it was base-10 rather
than base-2); in both cases the intent was fairly clear of, "this is a
hardware random device; it's fine."
So let's invert this logic. A hw_random struct's quality knob now
controls the maximum quality a driver can produce, or 0 to specify 1024.
Then, the module-wide switch called "default_quality" is changed to
represent the maximum quality of any driver. By default it's 1024, and
the quality of any particular driver is then given by:
min(default_quality, rng->quality ?: 1024);
This way, the user can still turn this off for weird reasons (and we can
replace whatever driver-specific disabling hacks existed in the past),
yet we get proper crediting for relevant RNGs.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull dmi updates from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Fortify entry point length checks
linux-next for a couple of months without, to my knowledge, any negative
reports (or any positive ones, come to that).
- Also the Maple Tree from Liam R. Howlett. An overlapping range-based
tree for vmas. It it apparently slight more efficient in its own right,
but is mainly targeted at enabling work to reduce mmap_lock contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
(https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com).
This has yet to be addressed due to Liam's unfortunately timed
vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down to
the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to support
file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY0HaPgAKCRDdBJ7gKXxA
joPjAQDZ5LlRCMWZ1oxLP2NOTp6nm63q9PWcGnmY50FjD/dNlwEAnx7OejCLWGWf
bbTuk6U2+TKgJa4X7+pbbejeoqnt5QU=
=xfWx
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Yu Zhao's Multi-Gen LRU patches are here. They've been under test in
linux-next for a couple of months without, to my knowledge, any
negative reports (or any positive ones, come to that).
- Also the Maple Tree from Liam Howlett. An overlapping range-based
tree for vmas. It it apparently slightly more efficient in its own
right, but is mainly targeted at enabling work to reduce mmap_lock
contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
at [1]. This has yet to be addressed due to Liam's unfortunately
timed vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down
to the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to
support file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and
memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging
activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
Link: https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com [1]
* tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (555 commits)
hugetlb: allocate vma lock for all sharable vmas
hugetlb: take hugetlb vma_lock when clearing vma_lock->vma pointer
hugetlb: fix vma lock handling during split vma and range unmapping
mglru: mm/vmscan.c: fix imprecise comments
mm/mglru: don't sync disk for each aging cycle
mm: memcontrol: drop dead CONFIG_MEMCG_SWAP config symbol
mm: memcontrol: use do_memsw_account() in a few more places
mm: memcontrol: deprecate swapaccounting=0 mode
mm: memcontrol: don't allocate cgroup swap arrays when memcg is disabled
mm/secretmem: remove reduntant return value
mm/hugetlb: add available_huge_pages() func
mm: remove unused inline functions from include/linux/mm_inline.h
selftests/vm: add selftest for MADV_COLLAPSE of uffd-minor memory
selftests/vm: add file/shmem MADV_COLLAPSE selftest for cleared pmd
selftests/vm: add thp collapse shmem testing
selftests/vm: add thp collapse file and tmpfs testing
selftests/vm: modularize thp collapse memory operations
selftests/vm: dedup THP helpers
mm/khugepaged: add tracepoint to hpage_collapse_scan_file()
mm/madvise: add file and shmem support to MADV_COLLAPSE
...
- implement EFI boot support for LoongArch
- implement generic EFI compressed boot support for arm64, RISC-V and
LoongArch, none of which implement a decompressor today
- measure the kernel command line into the TPM if measured boot is in
effect
- refactor the EFI stub code in order to isolate DT dependencies for
architectures other than x86
- avoid calling SetVirtualAddressMap() on arm64 if the configured size
of the VA space guarantees that doing so is unnecessary
- move some ARM specific code out of the generic EFI source files
- unmap kernel code from the x86 mixed mode 1:1 page tables
-----BEGIN PGP SIGNATURE-----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=d8Ps
-----END PGP SIGNATURE-----
Merge tag 'efi-next-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI updates from Ard Biesheuvel:
"A bit more going on than usual in the EFI subsystem. The main driver
for this has been the introduction of the LoonArch architecture last
cycle, which inspired some cleanup and refactoring of the EFI code.
Another driver for EFI changes this cycle and in the future is
confidential compute.
The LoongArch architecture does not use either struct bootparams or DT
natively [yet], and so passing information between the EFI stub and
the core kernel using either of those is undesirable. And in general,
overloading DT has been a source of issues on arm64, so using DT for
this on new architectures is a to avoid for the time being (even if we
might converge on something DT based for non-x86 architectures in the
future). For this reason, in addition to the patch that enables EFI
boot for LoongArch, there are a number of refactoring patches applied
on top of which separate the DT bits from the generic EFI stub bits.
These changes are on a separate topich branch that has been shared
with the LoongArch maintainers, who will include it in their pull
request as well. This is not ideal, but the best way to manage the
conflicts without stalling LoongArch for another cycle.
Another development inspired by LoongArch is the newly added support
for EFI based decompressors. Instead of adding yet another
arch-specific incarnation of this pattern for LoongArch, we are
introducing an EFI app based on the existing EFI libstub
infrastructure that encapulates the decompression code we use on other
architectures, but in a way that is fully generic. This has been
developed and tested in collaboration with distro and systemd folks,
who are eager to start using this for systemd-boot and also for arm64
secure boot on Fedora. Note that the EFI zimage files this introduces
can also be decompressed by non-EFI bootloaders if needed, as the
image header describes the location of the payload inside the image,
and the type of compression that was used. (Note that Fedora's arm64
GRUB is buggy [0] so you'll need a recent version or switch to
systemd-boot in order to use this.)
Finally, we are adding TPM measurement of the kernel command line
provided by EFI. There is an oversight in the TCG spec which results
in a blind spot for command line arguments passed to loaded images,
which means that either the loader or the stub needs to take the
measurement. Given the combinatorial explosion I am anticipating when
it comes to firmware/bootloader stacks and firmware based attestation
protocols (SEV-SNP, TDX, DICE, DRTM), it is good to set a baseline now
when it comes to EFI measured boot, which is that the kernel measures
the initrd and command line. Intermediate loaders can measure
additional assets if needed, but with the baseline in place, we can
deploy measured boot in a meaningful way even if you boot into Linux
straight from the EFI firmware.
Summary:
- implement EFI boot support for LoongArch
- implement generic EFI compressed boot support for arm64, RISC-V and
LoongArch, none of which implement a decompressor today
- measure the kernel command line into the TPM if measured boot is in
effect
- refactor the EFI stub code in order to isolate DT dependencies for
architectures other than x86
- avoid calling SetVirtualAddressMap() on arm64 if the configured
size of the VA space guarantees that doing so is unnecessary
- move some ARM specific code out of the generic EFI source files
- unmap kernel code from the x86 mixed mode 1:1 page tables"
* tag 'efi-next-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: (24 commits)
efi/arm64: libstub: avoid SetVirtualAddressMap() when possible
efi: zboot: create MemoryMapped() device path for the parent if needed
efi: libstub: fix up the last remaining open coded boot service call
efi/arm: libstub: move ARM specific code out of generic routines
efi/libstub: measure EFI LoadOptions
efi/libstub: refactor the initrd measuring functions
efi/loongarch: libstub: remove dependency on flattened DT
efi: libstub: install boot-time memory map as config table
efi: libstub: remove DT dependency from generic stub
efi: libstub: unify initrd loading between architectures
efi: libstub: remove pointless goto kludge
efi: libstub: simplify efi_get_memory_map() and struct efi_boot_memmap
efi: libstub: avoid efi_get_memory_map() for allocating the virt map
efi: libstub: drop pointless get_memory_map() call
efi: libstub: fix type confusion for load_options_size
arm64: efi: enable generic EFI compressed boot
loongarch: efi: enable generic EFI compressed boot
riscv: efi: enable generic EFI compressed boot
efi/libstub: implement generic EFI zboot
efi/libstub: move efi_system_table global var into separate object
...
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
- arm64 perf: DDR PMU driver for Alibaba's T-Head Yitian 710 SoC, SVE
vector granule register added to the user regs together with SVE perf
extensions documentation.
- SVE updates: add HWCAP for SVE EBF16, update the SVE ABI documentation
to match the actual kernel behaviour (zeroing the registers on syscall
rather than "zeroed or preserved" previously).
- More conversions to automatic system registers generation.
- vDSO: use self-synchronising virtual counter access in gettimeofday()
if the architecture supports it.
- arm64 stacktrace cleanups and improvements.
- arm64 atomics improvements: always inline assembly, remove LL/SC
trampolines.
- Improve the reporting of EL1 exceptions: rework BTI and FPAC exception
handling, better EL1 undefs reporting.
- Cortex-A510 erratum 2658417: remove BF16 support due to incorrect
result.
- arm64 defconfig updates: build CoreSight as a module, enable options
necessary for docker, memory hotplug/hotremove, enable all PMUs
provided by Arm.
- arm64 ptrace() support for TPIDR2_EL0 (register provided with the SME
extensions).
- arm64 ftraces updates/fixes: fix module PLTs with mcount, remove
unused function.
- kselftest updates for arm64: simple HWCAP validation, FP stress test
improvements, validation of ZA regs in signal handlers, include larger
SVE and SME vector lengths in signal tests, various cleanups.
- arm64 alternatives (code patching) improvements to robustness and
consistency: replace cpucap static branches with equivalent
alternatives, associate callback alternatives with a cpucap.
- Miscellaneous updates: optimise kprobe performance of patching
single-step slots, simplify uaccess_mask_ptr(), move MTE registers
initialisation to C, support huge vmalloc() mappings, run softirqs on
the per-CPU IRQ stack, compat (arm32) misalignment fixups for
multiword accesses.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAmM9W4cACgkQa9axLQDI
XvEy3w/+LJ3KCFowWiz5gTAWikjv+UVssHjLMJixn47V7hsEFQ26Xnam/438rTMI
kE95u6DHUpw2SMIxKzFRO7oI5cQtP+cWGwTtOUnjVO+U1oN+HqDOIbO9DbylWDcU
eeeqMMmawMfTPuZrYklpOhXscsorbrKIvYBg7wHYOcwBYV3EPhWr89lwMvTVRuyJ
qpX628KlkGMaBcONNhv3nS3qZcAOs0oHQCAVS4C8czLDL+vtJlumXUS3xr1Mqm72
xtFe7sje8Djr2kZ8mzh0GbFiZEBoBD3F/l7ayq8gVRaVpToUt8sk36Stjs4LojF1
6imuAfji/5TItkScq5KhGqj6MIugwp/eUVbRN74OLNTYx7msF1ZADNFQ+Q0UuY0H
SYK13KvmOji0xjS8qAfhqrwNB79sk3fb+zF9LjETbdz4ZJCgg9gcFbSUTY0DvMfS
MXZk/jVeB07olA8xYbjh0BRt4UV9xU628FPQzK5k7e4Nzl4jSvgtJZCZanfuVtjy
/ZS1vbN8o7tQLBAlVnw+Exi/VedkKxkkMgm8tPKsMgERTFDx0Pc4Gs72hRpDnPWT
MRbeCCGleAf3JQ5vF0coBDNOCEVvweQgShHOyHTz0GyhWXLCFx3RJICo5I4EIpps
LLUk4JK0fO3LVrf1AEpu5ZP4+Sact0zfsH3gB7qyLPYFDmjDXD8=
=jl3Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 perf: DDR PMU driver for Alibaba's T-Head Yitian 710 SoC, SVE
vector granule register added to the user regs together with SVE perf
extensions documentation.
- SVE updates: add HWCAP for SVE EBF16, update the SVE ABI
documentation to match the actual kernel behaviour (zeroing the
registers on syscall rather than "zeroed or preserved" previously).
- More conversions to automatic system registers generation.
- vDSO: use self-synchronising virtual counter access in gettimeofday()
if the architecture supports it.
- arm64 stacktrace cleanups and improvements.
- arm64 atomics improvements: always inline assembly, remove LL/SC
trampolines.
- Improve the reporting of EL1 exceptions: rework BTI and FPAC
exception handling, better EL1 undefs reporting.
- Cortex-A510 erratum 2658417: remove BF16 support due to incorrect
result.
- arm64 defconfig updates: build CoreSight as a module, enable options
necessary for docker, memory hotplug/hotremove, enable all PMUs
provided by Arm.
- arm64 ptrace() support for TPIDR2_EL0 (register provided with the SME
extensions).
- arm64 ftraces updates/fixes: fix module PLTs with mcount, remove
unused function.
- kselftest updates for arm64: simple HWCAP validation, FP stress test
improvements, validation of ZA regs in signal handlers, include
larger SVE and SME vector lengths in signal tests, various cleanups.
- arm64 alternatives (code patching) improvements to robustness and
consistency: replace cpucap static branches with equivalent
alternatives, associate callback alternatives with a cpucap.
- Miscellaneous updates: optimise kprobe performance of patching
single-step slots, simplify uaccess_mask_ptr(), move MTE registers
initialisation to C, support huge vmalloc() mappings, run softirqs on
the per-CPU IRQ stack, compat (arm32) misalignment fixups for
multiword accesses.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (126 commits)
arm64: alternatives: Use vdso/bits.h instead of linux/bits.h
arm64/kprobe: Optimize the performance of patching single-step slot
arm64: defconfig: Add Coresight as module
kselftest/arm64: Handle EINTR while reading data from children
kselftest/arm64: Flag fp-stress as exiting when we begin finishing up
kselftest/arm64: Don't repeat termination handler for fp-stress
ARM64: reloc_test: add __init/__exit annotations to module init/exit funcs
arm64/mm: fold check for KFENCE into can_set_direct_map()
arm64: ftrace: fix module PLTs with mcount
arm64: module: Remove unused plt_entry_is_initialized()
arm64: module: Make plt_equals_entry() static
arm64: fix the build with binutils 2.27
kselftest/arm64: Don't enable v8.5 for MTE selftest builds
arm64: uaccess: simplify uaccess_mask_ptr()
arm64: asm/perf_regs.h: Avoid C++-style comment in UAPI header
kselftest/arm64: Fix typo in hwcap check
arm64: mte: move register initialization to C
arm64: mm: handle ARM64_KERNEL_USES_PMD_MAPS in vmemmap_populate()
arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()
arm64/sve: Add Perf extensions documentation
...
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU: simplified VBIF configuration
- cleanup CTL interfaces
- DSI: removed unused msm_display_dsc_config struct
- switch regulator calls to new API
- switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- Improve error and edge conditions handling
- Convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- Add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support
-----BEGIN PGP SIGNATURE-----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=u/MJ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff all over, some new AMD IP support and gang submit
support. i915 has further DG2 and Meteorlake pieces, and a bunch of
i915 display refactoring. msm has a shrinker rework. There are also a
bunch of conversions to use kunit.
This has two external pieces, some MEI changes needed for future Intel
discrete GPUs. These should be acked by Greg. There is also a cross
maintainer shared tree with some backlight rework from Hans in here.
Core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU:
simplified VBIF configuration
cleanup CTL interfaces
- DSI:
removed unused msm_display_dsc_config struct
switch regulator calls to new API
switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduce lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- improve error and edge conditions handling
- convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support"
* tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm: (1374 commits)
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
drm/amdkfd: Track unified memory when switching xnack mode
drm/amdgpu: Enable sram on vcn_4_0_2
drm/amdgpu: Enable VCN DPG for GC11_0_1
drm/msm: Fix build break with recent mm tree
drm/panel: simple: Use dev_err_probe() to simplify code
drm/panel: panel-edp: Use dev_err_probe() to simplify code
drm/panel: simple: Add Multi-Inno Technology MI0800FT-9
dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel
drm/amdgpu: correct the memcpy size for ip discovery firmware
drm/amdgpu: Skip put_reset_domain if it doesn't exist
drm/amdgpu: remove switch from amdgpu_gmc_noretry_set
drm/amdgpu: Fix mc_umc_status used uninitialized warning
drm/amd/display: Prevent OTG shutdown during PSR SU
drm/amdgpu: add page retirement handling for CPU RAS
drm/amdgpu: use RAS error address convert api in mca notifier
drm/amdgpu: support to convert dedicated umc mca address
drm/amdgpu: export umc error address convert interface
drm/amdgpu: fix sdma v4 init microcode error
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback()
...
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
This replaces the prior support for Clang's standard Control Flow
Integrity (CFI) instrumentation, which has required a lot of special
conditions (e.g. LTO) and work-arounds. The current implementation
("Kernel CFI") is specific to C, directly designed for the Linux kernel,
and takes advantage of architectural features like x86's IBT. This
series retains arm64 support and adds x86 support. Additional "generic"
architectural support is expected soon:
https://github.com/samitolvanen/llvm-project/commits/kcfi_generic
- treewide: Remove old CFI support details
- arm64: Replace Clang CFI support with Clang KCFI support
- x86: Introduce Clang KCFI support
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAmM4aAUWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJkgWD/4mUgb7xewNIG/+fuipGd620Iao
K0T8q4BNxLNRltOxNc3Q0WMDCggX0qJGCeds7EdFQJQOGxWcbifM8MAS4idAGM0G
fc3Gxl1imC/oF6goCAbQgndA6jYFIWXGsv8LsRjAXRidWLFr3GFAqVqYJyokSySr
8zMQsEDuF4I1gQnOhEWdtPZbV3MQ4ZjfFzpv+33agbq6Gb72vKvDh3G6g2VXlxjt
1qnMtS+eEpbBU65cJkOi4MSLgymWbnIAeTMb0dbsV4kJ08YoTl8uz1B+weeH6GgT
WP73ZJ4nqh1kkkT9EqS9oKozNB9fObhvCokEuAjuQ7i1eCEZsbShvRc0iL7OKTGG
UfuTJa5qQ4h7Z0JS35FCSJETa+fcG0lTyEd133nLXLMZP9K2antf+A6O//fd0J1V
Jg4VN7DQmZ+UNGOzRkL6dTtQUy4PkxhniIloaClfSYXxhNirA+v//sHTnTK3z2Bl
6qceYqmFmns2Laual7+lvnZgt6egMBcmAL/MOdbU74+KIR9Xw76wxQjifktHX+WF
FEUQkUJDB5XcUyKlbvHoqobRMxvEZ8RIlC5DIkgFiPRE3TI0MqfzNSFnQ/6+lFNg
Y0AS9HYJmcj8sVzAJ7ji24WPFCXzsbFn6baJa9usDNbWyQZokYeiv7ZPNPHPDVrv
YEBP6aYko0lVSUS9qw==
=Li4D
-----END PGP SIGNATURE-----
Merge tag 'kcfi-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kcfi updates from Kees Cook:
"This replaces the prior support for Clang's standard Control Flow
Integrity (CFI) instrumentation, which has required a lot of special
conditions (e.g. LTO) and work-arounds.
The new implementation ("Kernel CFI") is specific to C, directly
designed for the Linux kernel, and takes advantage of architectural
features like x86's IBT. This series retains arm64 support and adds
x86 support.
GCC support is expected in the future[1], and additional "generic"
architectural support is expected soon[2].
Summary:
- treewide: Remove old CFI support details
- arm64: Replace Clang CFI support with Clang KCFI support
- x86: Introduce Clang KCFI support"
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107048 [1]
Link: https://github.com/samitolvanen/llvm-project/commits/kcfi_generic [2]
* tag 'kcfi-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (22 commits)
x86: Add support for CONFIG_CFI_CLANG
x86/purgatory: Disable CFI
x86: Add types to indirectly called assembly functions
x86/tools/relocs: Ignore __kcfi_typeid_ relocations
kallsyms: Drop CONFIG_CFI_CLANG workarounds
objtool: Disable CFI warnings
objtool: Preserve special st_shndx indexes in elf_update_symbol
treewide: Drop __cficanonical
treewide: Drop WARN_ON_FUNCTION_MISMATCH
treewide: Drop function_nocfi
init: Drop __nocfi from __init
arm64: Drop unneeded __nocfi attributes
arm64: Add CFI error handling
arm64: Add types to indirect called assembly functions
psci: Fix the function type for psci_initcall_t
lkdtm: Emit an indirect call for CFI tests
cfi: Add type helper macros
cfi: Switch to -fsanitize=kcfi
cfi: Drop __CFI_ADDRESSABLE
cfi: Remove CONFIG_CFI_CLANG_SHADOW
...
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki).
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus).
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw).
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus).
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello).
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry).
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen).
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv).
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko).
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello).
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin).
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede).
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner).
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton).
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan).
- Fix Tx acknowledge in the PCC address space handler (Huisong Li).
- Use wait_for_completion_timeout() for PCC mailbox operations (Huisong
Li).
- Release resources on PCC address space setup failure path (Rafael
Mendonca).
- Remove unneeded result variables from APEI code (ye xingchen).
- Print total number of records found during BERT log parsing (Dmitry
Monakhov).
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello).
- Drop unneeded result variable from ec_write() (ye xingchen).
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver (Hanjun
Guo).
- Reorder symbols to get rid of a few forward declarations in the ACPI
fan driver (Uwe Kleine-König).
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander).
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam).
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki).
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang).
- Do not initialize ret in main() in the pfrut utility (Shi junming).
- Drop useless ACPI DSDT override documentation (Rafael Wysocki).
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare).
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into an
integer value (Andy Shevchenko).
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko).
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui).
-----BEGIN PGP SIGNATURE-----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=xyUK
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"ACPI and PNP updates for 6.1-rc1.
These rearrange the ACPI device object initialization code (to get rid
of a redundant parent pointer from struct acpi_device among other
things), unify the _UID handling, drop support for some _OSI strings
that should not be necessary any more, add new IDs to support more
hardware and some more quirks, fix a few issues and clean up code all
over.
Specifics:
- Reimplement acpi_get_pci_dev() using the list of physical devices
associated with the given ACPI device object (Rafael Wysocki)
- Rename ACPI device object reference counting functions (Rafael
Wysocki)
- Rearrange ACPI device object initialization code (Rafael Wysocki)
- Drop parent field from struct acpi_device (Rafael Wysocki)
- Extend the the int3472-tps68470 driver to support multiple
consumers of a single TPS68470 along with the requisite
framework-level support (Daniel Scally)
- Filter out non-memory resources in is_memory(), add a helper
function to find all memory type resources of an ACPI device object
and use that function in 3 places (Heikki Krogerus)
- Add IRQ override quirks for Asus Vivobook K3402ZA/K3502ZA and ASUS
model S5402ZA (Tamim Khan, Kellen Renshaw)
- Fix acpi_dev_state_d0() kerneldoc (Sakari Ailus)
- Fix up suspend-to-idle support on ASUS Rembrandt laptops (Mario
Limonciello)
- Clean up ACPI platform devices support code (Andy Shevchenko, John
Garry)
- Clean up ACPI bus management code (Andy Shevchenko, ye xingchen)
- Add support for multiple DMA windows with different offsets to the
ACPI device enumeration code and use it on LoongArch (Jianmin Lv)
- Clean up the ACPI LPSS (Intel SoC) driver (Andy Shevchenko)
- Add a quirk for Dell Inspiron 14 2-in-1 for StorageD3Enable (Mario
Limonciello)
- Drop unused dev_fmt() and redundant 'HMAT' prefix from the HMAT
parsing code (Liu Shixin)
- Make ACPI FPDT parsing code avoid calling acpi_os_map_memory() on
invalid physical addresses (Hans de Goede)
- Silence missing-declarations warning related to Apple device
properties management (Lukas Wunner)
- Disable frequency invariance in the CPPC library if registers used
by cppc_get_perf_ctrs() are accessed via PCC (Jeremy Linton)
- Add ACPI disabled check to acpi_cpc_valid() (Perry Yuan)
- Fix Tx acknowledge in the PCC address space handler (Huisong Li)
- Use wait_for_completion_timeout() for PCC mailbox operations
(Huisong Li)
- Release resources on PCC address space setup failure path (Rafael
Mendonca)
- Remove unneeded result variables from APEI code (ye xingchen)
- Print total number of records found during BERT log parsing (Dmitry
Monakhov)
- Drop support for 3 _OSI strings that should not be necessary any
more and update documentation on custom _OSI strings so that adding
new ones is not encouraged any more (Mario Limonciello)
- Drop unneeded result variable from ec_write() (ye xingchen)
- Remove the leftover struct acpi_ac_bl from the ACPI AC driver
(Hanjun Guo)
- Reorder symbols to get rid of a few forward declarations in the
ACPI fan driver (Uwe Kleine-König)
- Add Toshiba Satellite/Portege Z830 ACPI backlight quirk (Arvid
Norlander)
- Add ARM DMA-330 controller to the supported list in the ACPI AMBA
driver (Vijayenthiran Subramaniam)
- Drop references to non-functional 01.org/linux-acpi web site from
MAINTAINERS and Kconfig help texts (Rafael Wysocki)
- Replace strlcpy() with unused retval with strscpy() in the ACPI
support code (Wolfram Sang)
- Do not initialize ret in main() in the pfrut utility (Shi junming)
- Drop useless ACPI DSDT override documentation (Rafael Wysocki)
- Fix a few typos and wording mistakes in the ACPI device enumeration
documentation (Jean Delvare)
- Introduce acpi_dev_uid_to_integer() to convert a _UID string into
an integer value (Andy Shevchenko)
- Use acpi_dev_uid_to_integer() in several places to unify _UID
handling (Andy Shevchenko)
- Drop unused pnpid32_to_pnpid() declaration from PNP code (Gaosheng
Cui)"
* tag 'acpi-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (79 commits)
ACPI: LPSS: Deduplicate skipping device in acpi_lpss_create_device()
ACPI: LPSS: Replace loop with first entry retrieval
ACPI: x86: s2idle: Add another ID to s2idle_dmi_table
ACPI: x86: s2idle: Fix a NULL pointer dereference
MAINTAINERS: Drop records pointing to 01.org/linux-acpi
ACPI: Kconfig: Drop link to https://01.org/linux-acpi
ACPI: docs: Drop useless DSDT override documentation
ACPI: DPTF: Drop stale link from Kconfig help
ACPI: x86: s2idle: Add a quirk for ASUSTeK COMPUTER INC. ROG Flow X13
ACPI: x86: s2idle: Add a quirk for Lenovo Slim 7 Pro 14ARH7
ACPI: x86: s2idle: Add a quirk for ASUS ROG Zephyrus G14
ACPI: x86: s2idle: Add a quirk for ASUS TUF Gaming A17 FA707RE
ACPI: x86: s2idle: Add module parameter to prefer Microsoft GUID
ACPI: x86: s2idle: If a new AMD _HID is missing assume Rembrandt
ACPI: x86: s2idle: Move _HID handling for AMD systems into structures
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
...
To ease debugging of PSCI supported features, add debugfs file called
'psci' describing PSCI and SMC CC versions, enabled features and
options.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220926110758.666922-1-dmitry.baryshkov@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The function psci_pd_try_set_osi_mode() will print an error if enabling
OSI mode fails. To ease debugging PSCI issues print corresponding
message if switching to PC mode fails too.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20220926110249.666813-1-dmitry.baryshkov@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Terminate infinite loop in SD-UHS voltage switch
MMC host:
- hsq: Fix kernel crash in the recovery path
- moxart: Fix bus width configurations
- sdhci: Fix kernel panic for cqe irq
ARM_SCMI:
- Fixup clock management by reverting "firmware: arm_scmi: Add clock
management to the SCMI power domain"
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmM0BoQXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCmFIw//ZhctvlbOQa2StMO2GrJfgQGi
ELclXWN1MzyyTN2v93LRrIwu1FR3vFV8sJ/80wlt+o0l4XBuwewmlUXdxGEdKwKA
2+Luj5f2sDf1z9wXsVLjybQ7ujD60jSrXgO6sGvF8a4cy0sCW7O3/3sytrXXHqzj
vU5zvr4Y6aBiruEpAFXBKyGWxpj0iFjvMo+ZuJpOHgHiVSF2UWOXuLbuAn04ESG6
Z3sn8qMZbTFI1HoE2XHF7xB10j9sYu09Urp57xAUFLuYf7Rr+MRNDqjByESnl9H7
SZcgomCoycUyjSDSLqdrr0Z4eJ7zacyHRHEYEzX/owAanE9GQpwGDauDYrVHFn7o
75uT6ZhJZwoLguM+6NiURYraIl75o4ijDKhFYrm+8dEmFfTi3hy9Ey86pFsr3UWm
RC+Dxi/oY7mkrpAEwJwkixzUGKqX/42a9zBcUbejE8x1UEw8sljboz3kEzTBlaDU
4mhdeY5//dHOhl3V8V9Oj9rQZJ7jfPJbrg0qK65EEDW5TumMTGnQzR9Zl1BfWBIA
lzIKq3USZ+5Gm8KvZ0yYq8bHmGaYKd/aFfZ3RTHIsPPx7pXt0G81SkE+eJ/jDkRN
FL7TU1wgWU9ovFw0N1LScr/EH/juIl+3bqhMRSuk5cBgDdVuCmKT5XS/694GfZkl
/JUySvxena/yGlNn/Mg=
=F5JH
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes. This time there is also a fix for the ARM SCMI
firmware driver, which has been acked by Sudeep Holla, the maintainer.
MMC core:
- Terminate infinite loop in SD-UHS voltage switch
MMC host:
- hsq: Fix kernel crash in the recovery path
- moxart: Fix bus width configurations
- sdhci: Fix kernel panic for cqe irq
ARM_SCMI:
- Fixup clock management by reverting 'firmware: arm_scmi: Add clock
management to the SCMI power domain'"
* tag 'mmc-v6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: hsq: Fix data stomping during mmc recovery
Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
mmc: core: Terminate infinite loop in SD-UHS voltage switch
mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
mmc: sdhci: Fix host->cmd is null
EFI's SetVirtualAddressMap() runtime service is a horrid hack that we'd
like to avoid using, if possible. For 64-bit architectures such as
arm64, the user and kernel mappings are entirely disjoint, and given
that we use the user region for mapping the UEFI runtime regions when
running under the OS, we don't rely on SetVirtualAddressMap() in the
conventional way, i.e., to permit kernel mappings of the OS to coexist
with kernel region mappings of the firmware regions. This means that, in
principle, we should be able to avoid SetVirtualAddressMap() altogether,
and simply use the 1:1 mapping that UEFI uses at boot time. (Note that
omitting SetVirtualAddressMap() is explicitly permitted by the UEFI
spec).
However, there is a corner case on arm64, which, if configured for
3-level paging (or 2-level paging when using 64k pages), may not be able
to cover the entire range of firmware mappings (which might contain both
memory and MMIO peripheral mappings).
So let's avoid SetVirtualAddressMap() on arm64, but only if the VA space
is guaranteed to be of sufficient size.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
LoadImage() is supposed to install an instance of the protocol
EFI_LOADED_IMAGE_DEVICE_PATH_PROTOCOL onto the loaded image's handle so
that the program can figure out where it was loaded from. The reference
implementation even does this (with a NULL protocol pointer) if the call
to LoadImage() used the source buffer and size arguments, and passed
NULL for the image device path. Hand rolled implementations of LoadImage
may behave differently, though, and so it is better to tolerate
situations where the protocol is missing. And actually, concatenating an
Offset() node to a NULL device path (as we do currently) is not great
either.
So in cases where the protocol is absent, or when it points to NULL,
construct a MemoryMapped() device node as the base node that describes
the parent image's footprint in memory.
Cc: Daan De Meyer <daandemeyer@fb.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We use a macro efi_bs_call() to call boot services, which is more
concise, and on x86, it encapsulates the mixed mode handling. This code
does not run in mixed mode, but let's switch to the macro for general
tidiness.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Move some code that is only reachable when IS_ENABLED(CONFIG_ARM) into
the ARM EFI arch code.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The EFI TCG spec, in §10.2.6 "Measuring UEFI Variables and UEFI GPT
Data", only reasons about the load options passed to a loaded image in
the context of boot options booted directly from the BDS, which are
measured into PCR #5 along with the rest of the Boot#### EFI variable.
However, the UEFI spec mentions the following in the documentation of
the LoadImage() boot service and the EFI_LOADED_IMAGE protocol:
The caller may fill in the image’s "load options" data, or add
additional protocol support to the handle before passing control to
the newly loaded image by calling EFI_BOOT_SERVICES.StartImage().
The typical boot sequence for Linux EFI systems is to load GRUB via a
boot option from the BDS, which [hopefully] calls LoadImage to load the
kernel image, passing the kernel command line via the mechanism
described above. This means that we cannot rely on the firmware
implementing TCG measured boot to ensure that the kernel command line
gets measured before the image is started, so the EFI stub will have to
take care of this itself.
Given that PCR #5 has an official use in the TCG measured boot spec,
let's avoid it in this case. Instead, add a measurement in PCR #9 (which
we already use for our initrd) and extend it with the LoadOptions
measurements
Co-developed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, from the efi-stub, we are only measuring the loaded initrd,
using the TCG2 measured boot protocols. A following patch is
introducing measurements of additional components, such as the kernel
command line. On top of that, we will shortly have to support other
types of measured boot that don't expose the TCG2 protocols.
So let's prepare for that, by rejigging the efi_measure_initrd() routine
into something that we should be able to reuse for measuring other
assets, and which can be extended later to support other measured boot
protocols.
Co-developed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
This is necessary because the EFI libstub refactoring patches are mostly
directed at enabling LoongArch to wire up generic EFI boot support
without being forced to consume DT properties that conflict with
information that EFI also provides, e.g., memory map and reservations,
etc.
-----BEGIN PGP SIGNATURE-----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=IlXm
-----END PGP SIGNATURE-----
Merge tag 'efi-loongarch-for-v6.1-2' into HEAD
Second shared stable tag between EFI and LoongArch trees
This is necessary because the EFI libstub refactoring patches are mostly
directed at enabling LoongArch to wire up generic EFI boot support
without being forced to consume DT properties that conflict with
information that EFI also provides, e.g., memory map and reservations,
etc.
LoongArch does not use FDT or DT natively [yet], and the only reason it
currently uses it is so that it can reuse the existing EFI stub code.
Overloading the DT with data passed between the EFI stub and the core
kernel has been a source of problems: there is the overlap between
information provided by EFI which DT can also provide (initrd base/size,
command line, memory descriptions), requiring us to reason about which
is which and what to prioritize. It has also resulted in ABI leaks,
i.e., internal ABI being promoted to external ABI inadvertently because
the bootloader can set the EFI stub's DT properties as well (e.g.,
"kaslr-seed"). This has become especially problematic with boot
environments that want to pretend that EFI boot is being done (to access
ACPI and SMBIOS tables, for instance) but have no ability to execute the
EFI stub, and so the environment that the EFI stub creates is emulated
[poorly, in some cases].
Another downside of treating DT like this is that the DT binary that the
kernel receives is different from the one created by the firmware, which
is undesirable in the context of secure and measured boot.
Given that LoongArch support in Linux is brand new, we can avoid these
pitfalls, and treat the DT strictly as a hardware description, and use a
separate handover method between the EFI stub and the kernel. Now that
initrd loading and passing the EFI memory map have been refactored into
pure EFI routines that use EFI configuration tables, the only thing we
need to pass directly is the kernel command line (even if we could pass
this via a config table as well, it is used extremely early, so passing
it directly is preferred in this case.)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Expose the EFI boot time memory map to the kernel via a configuration
table. This is arch agnostic and enables future changes that remove the
dependency on DT on architectures that don't otherwise rely on it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Refactor the generic EFI stub entry code so that all the dependencies on
device tree are abstracted and hidden behind a generic efi_boot_kernel()
routine that can also be implemented in other ways. This allows users of
the generic stub to avoid using FDT for passing information to the core
kernel.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Use a EFI configuration table to pass the initrd to the core kernel,
instead of per-arch methods. This cleans up the code considerably, and
should make it easier for architectures to get rid of their reliance on
DT for doing EFI boot in the future.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Remove the RB tree and start using the maple tree for vm_area_struct
tracking.
Drop validate_mm() calls in expand_upwards() and expand_downwards() as the
lock is not held.
Link: https://lkml.kernel.org/r/20220906194824.2110408-18-Liam.Howlett@oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Tested-by: Yu Zhao <yuzhao@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: SeongJae Park <sj@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Start tracking the VMAs with the new maple tree structure in parallel with
the rb_tree. Add debug and trace events for maple tree operations and
duplicate the rb_tree that is created on forks into the maple tree.
The maple tree is added to the mm_struct including the mm_init struct,
added support in required mm/mmap functions, added tracking in kernel/fork
for process forking, and used to find the unmapped_area and checked
against what the rbtree finds.
This also moves the mmap_lock() in exit_mmap() since the oom reaper call
does walk the VMAs. Otherwise lockdep will be unhappy if oom happens.
When splitting a vma fails due to allocations of the maple tree nodes,
the error path in __split_vma() calls new->vm_ops->close(new). The page
accounting for hugetlb is actually in the close() operation, so it
accounts for the removal of 1/2 of the VMA which was not adjusted. This
results in a negative exit value. To avoid the negative charge, set
vm_start = vm_end and vm_pgoff = 0.
There is also a potential accounting issue in special mappings from
insert_vm_struct() failing to allocate, so reverse the charge there in
the failure scenario.
Link: https://lkml.kernel.org/r/20220906194824.2110408-9-Liam.Howlett@oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: Yu Zhao <yuzhao@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: SeongJae Park <sj@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently, struct efi_boot_memmap is a struct that is passed around
between callers of efi_get_memory_map() and the users of the resulting
data, and which carries pointers to various variables whose values are
provided by the EFI GetMemoryMap() boot service.
This is overly complex, and it is much easier to carry these values in
the struct itself. So turn the struct into one that carries these data
items directly, including a flex array for the variable number of EFI
memory descriptors that the boot service may return.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The virt map is a set of efi_memory_desc_t descriptors that are passed
to SetVirtualAddressMap() to inform the firmware about the desired
virtual mapping of the regions marked as EFI_MEMORY_RUNTIME. The only
reason we currently call the efi_get_memory_map() helper is that it
gives us an allocation that is guaranteed to be of sufficient size.
However, efi_get_memory_map() has grown some additional complexity over
the years, and today, we're actually better off calling the EFI boot
service directly with a zero size, which tells us how much memory should
be enough for the virt map.
While at it, avoid creating the VA map allocation if we will not be
using it anyway, i.e., if efi_novamap is true.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
With -fsanitize=kcfi, we no longer need function_nocfi() as
the compiler won't change function references to point to a
jump table. Remove all implementations and uses of the macro.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220908215504.3686827-14-samitolvanen@google.com
Functions called through a psci_initcall_t pointer all have
non-const arguments. Fix the type definition to avoid tripping
indirect call checks with CFI_CLANG.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220908215504.3686827-9-samitolvanen@google.com
In preparation for removing CC_FLAGS_CFI from CC_FLAGS_LTO, explicitly
filter out CC_FLAGS_CFI in all the makefiles where we currently filter
out CC_FLAGS_LTO.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220908215504.3686827-2-samitolvanen@google.com
Currently the gsmi driver registers a panic notifier as well as
reboot and die notifiers. The callbacks registered are called in
atomic and very limited context - for instance, panic disables
preemption and local IRQs, also all secondary CPUs (not executing
the panic path) are shutdown.
With that said, taking a spinlock in this scenario is a dangerous
invitation for lockup scenarios. So, fix that by checking if the
spinlock is free to acquire in the panic notifier callback - if not,
bail-out and avoid a potential hang.
Fixes: 74c5b31c66 ("driver: Google EFI SMI")
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: David Gow <davidgow@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Petr Mladek <pmladek@suse.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20220909200755.189679-1-gpiccoli@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The icc-bwmon driver is expected to support measuring LLCC/DDR bandwidth
on SDM845 and SC7280.
The LLCC driver is extended to provide per-platform register mappings to
the LLCC EDAC driver. The QMI encoder/decoder is updated to allow the
passed qmi_elem_info to be const.
Support for SDM845 is added to the sleep stats driver. Power-domains for
the SM6375 platform is added to RPMPD and the platform is added to
socinfo, together with the PM6125 pmic id.
A couple of of_node reference issues are corrected in the smem state and
smsm drivers.
The Qualcomm SCM driver binding is converted to YAML.
-----BEGIN PGP SIGNATURE-----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=R/5I
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GSE8
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for 6.1
The icc-bwmon driver is expected to support measuring LLCC/DDR bandwidth
on SDM845 and SC7280.
The LLCC driver is extended to provide per-platform register mappings to
the LLCC EDAC driver. The QMI encoder/decoder is updated to allow the
passed qmi_elem_info to be const.
Support for SDM845 is added to the sleep stats driver. Power-domains for
the SM6375 platform is added to RPMPD and the platform is added to
socinfo, together with the PM6125 pmic id.
A couple of of_node reference issues are corrected in the smem state and
smsm drivers.
The Qualcomm SCM driver binding is converted to YAML.
* tag 'qcom-drivers-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (29 commits)
soc: qcom: rpmpd: Add SM6375 support
dt-bindings: power: rpmpd: Add SM6375 power domains
firmware: qcom: scm: remove unused __qcom_scm_init declaration
dt-bindings: power: qcom,rpmpd: drop non-working codeaurora.org emails
soc: qcom: icc-bwmon: force clear counter/irq registers
soc: qcom: icc-bwmon: add support for sc7280 LLCC BWMON
dt-bindings: interconnect: qcom,msm8998-bwmon: Add support for sc7280 BWMONs
soc: qcom: llcc: Pass LLCC version based register offsets to EDAC driver
soc: qcom: llcc: Rename reg_offset structs to reflect LLCC version
soc: qcom: qmi: use const for struct qmi_elem_info
soc: qcom: icc-bwmon: remove redundant ret variable
dt-bindings: soc: qcom: stats: Document SDM845 compatible
soc: qcom: stats: Add SDM845 stats config and compatible
dt-bindings: firmware: document Qualcomm SM6115 SCM
soc: qcom: Make QCOM_RPMPD depend on OF
dt-bindings: firmware: convert Qualcomm SCM binding to the yaml
soc: qcom: socinfo: Add PM6125 ID
soc: qcom: socinfo: Add an ID for SM6375
soc: qcom: smem_state: Add refcounting for the 'state->of_node'
soc: qcom: smsm: Fix refcount leak bugs in qcom_smsm_probe()
...
Link: https://lore.kernel.org/r/20220921155753.1316308-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ensure that the SMBIOS entry point is long enough to include all the
fields we need. Otherwise it is pointless to even attempt to verify
its checksum.
Also fix the maximum length check, which is technically 32, not 31.
It does not matter in practice as the only valid values are 31 (for
SMBIOS 2.x) and 24 (for SMBIOS 3.x), but let's still have the check
right in case new fields are added to either structure in the future.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/lkml/20220823094857.27f3d924@endymion.delvare/T/
This reverts commit a3b884cef8 ("firmware: arm_scmi: Add clock management
to the SCMI power domain").
Using the GENPD_FLAG_PM_CLK tells genpd to gate/ungate the consumer
device's clock(s) during runtime suspend/resume through the PM clock API.
More precisely, in genpd_runtime_resume() the clock(s) for the consumer
device would become ungated prior to the driver-level ->runtime_resume()
callbacks gets invoked.
This behaviour isn't a good fit for all platforms/drivers. For example, a
driver may need to make some preparations of its device in its
->runtime_resume() callback, like calling clk_set_rate() before the
clock(s) should be ungated. In these cases, it's easier to let the clock(s)
to be managed solely by the driver, rather than at the PM domain level.
For these reasons, let's drop the use GENPD_FLAG_PM_CLK for the SCMI PM
domain, as to enable it to be more easily adopted across ARM platforms.
Fixes: a3b884cef8 ("firmware: arm_scmi: Add clock management to the SCMI power domain")
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20220919122033.86126-1-ulf.hansson@linaro.org
Another set of fixes for fixes for the soc tree:
- A fix for the interrupt number on at91/lan966 ethernet PHYs
- A second round of fixes for NXP i.MX series, including a couple
of build issues, and board specific DT corrections on
TQMa8MPQL, imx8mp-venice-gw74xx and imx8mm-verdin for reliability
and partially broken functionality.
- Several fixes for Rockchip SoCs, addressing a USB issue on BPI-R2-Pro,
wakeup on Gru-Bob and reliability of high-speed SD cards, among
other minor issues.
- A fix for a long-running naming mistake that prevented the moxart mmc
driver from working at all.
- Multiple Arm SCMI firmware fixes for hardening some corner cases.
-----BEGIN PGP SIGNATURE-----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=fI2K
-----END PGP SIGNATURE-----
Merge tag 'soc-fixes-6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Another set of fixes for fixes for the soc tree:
- A fix for the interrupt number on at91/lan966 ethernet PHYs
- A second round of fixes for NXP i.MX series, including a couple of
build issues, and board specific DT corrections on TQMa8MPQL,
imx8mp-venice-gw74xx and imx8mm-verdin for reliability and
partially broken functionality
- Several fixes for Rockchip SoCs, addressing a USB issue on
BPI-R2-Pro, wakeup on Gru-Bob and reliability of high-speed SD
cards, among other minor issues
- A fix for a long-running naming mistake that prevented the moxart
mmc driver from working at all
- Multiple Arm SCMI firmware fixes for hardening some corner cases"
* tag 'soc-fixes-6.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
arm64: dts: imx8mp-venice-gw74xx: fix port/phy validation
ARM: dts: lan966x: Fix the interrupt number for internal PHYs
arm64: dts: imx8mp-venice-gw74xx: fix ksz9477 cpu port
arm64: dts: imx8mp-venice-gw74xx: fix CAN STBY polarity
dt-bindings: memory-controllers: fsl,imx8m-ddrc: drop Leonard Crestez
arm64: dts: tqma8mqml: Include phy-imx8-pcie.h header
arm64: defconfig: enable ARCH_NXP
arm64: dts: imx8mp-tqma8mpql-mba8mpxl: add missing pinctrl for RTC alarm
ARM: dts: fix Moxa SDIO 'compatible', remove 'sdhci' misnomer
arm64: dts: imx8mm-verdin: extend pmic voltages
arm64: dts: rockchip: Remove 'enable-active-low' from rk3566-quartz64-a
arm64: dts: rockchip: Remove 'enable-active-low' from rk3399-puma
arm64: dts: rockchip: fix property for usb2 phy supply on rk3568-evb1-v10
arm64: dts: rockchip: fix property for usb2 phy supply on rock-3a
arm64: dts: imx8ulp: add #reset-cells for pcc
arm64: dts: tqma8mpxl-ba8mpxl: Fix button GPIOs
arm64: dts: imx8mn: remove GPU power domain reset
arm64: dts: rockchip: Set RK3399-Gru PCLK_EDP to 24 MHz
arm64: dts: imx8mm: Reverse CPLD_Dn GPIO label mapping on MX8Menlo
arm64: dts: rockchip: fix upper usb port on BPI-R2-Pro
...
- Use the right variable to check for shim insecure mode
- Wipe setup_data field when booting via EFI
- Add missing error check to efibc driver
-----BEGIN PGP SIGNATURE-----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=Earg
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent-for-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Use the right variable to check for shim insecure mode
- Wipe setup_data field when booting via EFI
- Add missing error check to efibc driver
* tag 'efi-urgent-for-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: libstub: check Shim mode using MokSBStateRT
efi: x86: Wipe setup_data on pure EFI boot
efi: efibc: Guard against allocation failure
We currently check the MokSBState variable to decide whether we should
treat UEFI secure boot as being disabled, even if the firmware thinks
otherwise. This is used by shim to indicate that it is not checking
signatures on boot images. In the kernel, we use this to relax lockdown
policies.
However, in cases where shim is not even being used, we don't want this
variable to interfere with lockdown, given that the variable may be
non-volatile and therefore persist across a reboot. This means setting
it once will persistently disable lockdown checks on a given system.
So switch to the mirrored version of this variable, called MokSBStateRT,
which is supposed to be volatile, and this is something we can check.
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Jones <pjones@redhat.com>
When booting the x86 kernel via EFI using the LoadImage/StartImage boot
services [as opposed to the deprecated EFI handover protocol], the setup
header is taken from the image directly, and given that EFI's LoadImage
has no Linux/x86 specific knowledge regarding struct bootparams or
struct setup_header, any absolute addresses in the setup header must
originate from the file and not from a prior loading stage.
Since we cannot generally predict where LoadImage() decides to load an
image (*), such absolute addresses must be treated as suspect: even if a
prior boot stage intended to make them point somewhere inside the
[signed] image, there is no way to validate that, and if they point at
an arbitrary location in memory, the setup_data nodes will not be
covered by any signatures or TPM measurements either, and could be made
to contain an arbitrary sequence of SETUP_xxx nodes, which could
interfere quite badly with the early x86 boot sequence.
(*) Note that, while LoadImage() does take a buffer/size tuple in
addition to a device path, which can be used to provide the image
contents directly, it will re-allocate such images, as the memory
footprint of an image is generally larger than the PE/COFF file
representation.
Cc: <stable@vger.kernel.org> # v5.10+
Link: https://lore.kernel.org/all/20220904165321.1140894-1-Jason@zx2c4.com/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Currently, the non-x86 stub code calls get_memory_map() redundantly,
given that the data it returns is never used anywhere. So drop the call.
Cc: <stable@vger.kernel.org> # v4.14+
Fixes: 24d7c494ce ("efi/arm-stub: Round up FDT allocation to mapping size")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
There is a single kmalloc in this driver, and it's not currently
guarded against allocation failure. Do it here by just bailing-out
the reboot handler, in case this tentative allocation fails.
Fixes: 416581e486 ("efi: efibc: avoid efivar API for setting variables")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Even though it is unlikely to ever make a difference, let's use u32
consistently for the size of the load_options provided by the firmware
(aka the command line)
While at it, do some general cleanup too: use efi_char16_t, avoid using
options_chars in places where it really means options_size, etc.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Implement a minimal EFI app that decompresses the real kernel image and
launches it using the firmware's LoadImage and StartImage boot services.
This removes the need for any arch-specific hacks.
Note that on systems that have UEFI secure boot policies enabled,
LoadImage/StartImage require images to be signed, or their hashes known
a priori, in order to be permitted to boot.
There are various possible strategies to work around this requirement,
but they all rely either on overriding internal PI/DXE protocols (which
are not part of the EFI spec) or omitting the firmware provided
LoadImage() and StartImage() boot services, which is also undesirable,
given that they encapsulate platform specific policies related to secure
boot and measured boot, but also related to memory permissions (whether
or not and which types of heap allocations have both write and execute
permissions.)
The only generic and truly portable way around this is to simply sign
both the inner and the outer image with the same key/cert pair, so this
is what is implemented here.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Jason A. Donenfeld