If the device tree is incorrectly configured, and attempts to
define a "no-map" reserved memory that overlaps with the kernel
data/code, the kernel would crash quickly after boot, with no
obvious clue about the nature of the issue.
For example, this would happen if we have the kernel mapped at
these addresses (from /proc/iomem):
40000000-41ffffff : System RAM
40080000-40dfffff : Kernel code
40e00000-411fffff : reserved
41200000-413e0fff : Kernel data
And we declare a no-map shared-dma-pool region at a fixed address
within that range:
mem_reserved: mem_region {
compatible = "shared-dma-pool";
reg = <0 0x40000000 0 0x01A00000>;
no-map;
};
To fix this, when removing memory regions at early boot (which is
what "no-map" regions do), we need to make sure that the memory
is not already reserved. If we do, __reserved_mem_reserve_reg
will throw an error:
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory
for node 'mem_region': base 0x0000000040000000, size 26 MiB
and the code that will try to use the region should also fail,
later on.
We do not do anything for non-"no-map" regions, as memblock
explicitly allows reserved regions to overlap, and the commit
that this fixes removed the check for that precise reason.
[ qperret: fixed conflicts caused by the usage of memblock_mark_nomap ]
Fixes: 094cb98179 ("of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20210115114544.1830068-3-qperret@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Mark the memory region with NOMAP flag instead of completely removing it
from the memory blocks. That makes the FDT handling consistent with the EFI
memory map handling.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20210115114544.1830068-2-qperret@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Instead of using the array-of-pointers trick to avoid having gcc mess up
the earlycon array stride, specify type alignment when declaring entries
to prevent gcc from increasing alignment.
This is essentially an alternative (one-line) fix to the problem
addressed by commit dd709e72cb ("earlycon: Use a pointer table to fix
__earlycon_table stride").
gcc can increase the alignment of larger objects with static extent as
an optimisation, but this can be suppressed by using the aligned
attribute when declaring variables.
Note that we have been relying on this behaviour for kernel parameters
for 16 years and it indeed hasn't changed since the introduction of the
aligned attribute in gcc-3.1.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201123102319.8090-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For version 1 to 3 of the device tree, this is the node full
path as a zero terminated string, starting with "/". The
following equation will not hold, since the node name has
been processed in the fdt_get_name().
*pathp == '/'
For version 16 and later, this is the node unit name only
(or an empty string for the root node). So the above
equation will still not hold.
So the kbasename() is redundant, just remove it.
Signed-off-by: Qi Zheng <arch0.zheng@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Currently, there are some descriptions of function not
consistent with function name, fixing them will make
the code more readable.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Gerrit will complain with this warnings:
ERROR: (foo*) should be (foo *)
Signed-off-by: tangjianqiang <tangjianqiang@xiaomi.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404 interconnect,
Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
-----BEGIN PGP SIGNATURE-----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=L6uq
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
-----BEGIN PGP SIGNATURE-----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=QCEy
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
As said in commit f2c2cbcc35 ("powerpc: Use pr_warn instead of
pr_warning"), removing pr_warning so all logging messages use a
consistent <prefix>_warn style. Let's do it.
Link: http://lkml.kernel.org/r/20191018031850.48498-16-wangkefeng.wang@huawei.com
To: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
If of_setup_earlycon we should keep on iterating earlycon options
instead of breaking out of the loop.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 428826f535 ("fdt: add support for rng-seed") moves of_fdt_crc32
from early_init_dt_verify() to early_init_dt_scan() since
early_init_dt_scan_chosen() may modify fdt to erase rng-seed.
However, arm and some other arch won't call early_init_dt_scan(), they
call early_init_dt_verify() then early_init_dt_scan_nodes().
Restore of_fdt_crc32 to early_init_dt_verify() then update it in
early_init_dt_scan_chosen() if fdt if updated.
Fixes: 428826f535 ("fdt: add support for rng-seed")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will@kernel.org>
Introducing a chosen node, rng-seed, which is an entropy that can be
passed to kernel called very early to increase initial device
randomness. Bootloader should provide this entropy and the value is
read from /chosen/rng-seed in DT.
Obtain of_fdt_crc32 for CRC check after early_init_dt_scan_nodes(),
since early_init_dt_scan_chosen() would modify fdt to erase rng-seed.
Add a new interface add_bootloader_randomness() for rng-seed use case.
Depends on whether the seed is trustworthy, rng seed would be passed to
add_hwgenerator_randomness(). Otherwise it would be passed to
add_device_randomness(). Decision is controlled by kernel config
RANDOM_TRUST_BOOTLOADER.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu> # drivers/char/random.c
Signed-off-by: Will Deacon <will@kernel.org>
The third argument 'nomap' of early_init_dt_reserve_memory_arch() is
bool. It is preferred to pass it with a bool type parameter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When CONFIG_OF_EARLY_FLATTREE is disabled, there is a compiler
warning,
drivers/of/fdt.c:129:19: warning: ‘of_fdt_match’ defined but not used [-Wunused-function]
static int __init of_fdt_match(const void *blob, unsigned long node,
Since the only caller of of_fdt_match() is of_flat_dt_match(),
let's move the body of of_fdt_match() into of_flat_dt_match()
and eliminate of_fdt_match().
Meanwhile, move of_fdt_is_compatible() under CONFIG_OF_EARLY_FLATTREE,
as all callers are over there.
Fixes: 9b4d2b635b ("of/fdt: Remove dead code and mark functions with __init")
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The FDT pointer, i.e. initial_boot_params, shouldn't be changed after
init. It's only set by boot code and then the only user of the FDT is
the raw sysfs reading API. Mark this pointer with __ro_after_init so
that the pointer can't be changed after init.
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Some functions in here are never called, and others are only called
during __init. Remove the dead code and some dead exports for functions
that don't exist (I'm looking at you of_fdt_get_string!). Mark some
functions with __init so we can throw them away after we boot up and
poke at the FDT blob too.
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The type of variable l in early_init_dt_scan_chosen is
int, there is no need to convert to int.
Signed-off-by: xiaojiangfeng <xiaojiangfeng@huawei.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that all users of device_node.type pointer have been removed in
favor of accessor functions, we can remove it.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
On architectures that only get their bootargs through devicetree's
chosen node (such as RISC-V), that node is mandatory. After a
discussion with Rob [1] I'm adding a warning in case chosen node
is not present, to let users know about it.
[1]: https://patchwork.ozlabs.org/patch/984224/#2016136
Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that ARM64 uses phys_initrd_start/phys_initrd_size, we can get rid
of its custom __early_init_dt_declare_initrd() which causes a fair
amount of objects rebuild when changing CONFIG_BLK_DEV_INITRD. In order
to make sure ARM64 does not produce a BUG() when VM debugging is turned
on though, we must avoid early calls to __va() which is what
__early_init_dt_declare_initrd() does and wrap this around to avoid
running that code on ARM64.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that we have central and global variables holding the physical
address and size of the initrd, we can have
early_init_dt_check_for_initrd() populate
phys_initrd_start/phys_initrd_size for us.
This allows us to remove a chunk of code from arch/arm/mm/init.c
introduced with commit 65939301ac ("arm: set initrd_start/initrd_end
for fdt scan").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architecures use memblock for early memory management. There is no need
for the CONFIG_HAVE_MEMBLOCK configuration option.
[rppt@linux.vnet.ibm.com: of/fdt: fixup #ifdefs]
Link: http://lkml.kernel.org/r/20180919103457.GA20545@rapoport-lnx
[rppt@linux.vnet.ibm.com: csky: fixups after bootmem removal]
Link: http://lkml.kernel.org/r/20180926112744.GC4628@rapoport-lnx
[rppt@linux.vnet.ibm.com: remove stale #else and the code it protects]
Link: http://lkml.kernel.org/r/1538067825-24835-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1536927045-23536-4-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory region size is rounded down to page boundary and with sub-page
region it becomes 0 and there is no point to add an empty region.
Moreover, when the base is less than PAGE_SIZE we get a bogus size as
(base + size - 1) evaluates to -1.
8cccffc526 ("of: check for size < 0 after rounding in
early_init_dt_add_memory_arch") introduced a test for wrap around for the
case when base is not page aligned, the same test can be used to ignore
sub-page region sizes.
Link: http://lkml.kernel.org/r/1533326330-31677-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the OF code was originally made common by Grant in commit
51975db0b7 ("of/flattree: merge early_init_dt_scan_memory() common
code") (Feb 2010), the common code inherited a hack to handle
PPC "longtrail" machines, which had a "memory@0" node with no
device_type.
That check was then made to only apply to PPC32 in b44aa25d20 ("of:
Handle memory@0 node on PPC32 only") (May 2014).
But according to Paul Mackerras the "longtrail" machines are long
dead, if they were ever seen in the wild at all. If someone does still
have one, we can handle this firmware wart in powerpc platform code.
So remove the hack once and for all.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 99492c39f3 ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol. This
fix was based on commit 07fca0e57f ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.
However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format. In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array. If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".
To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
3d56e331b6 ("tracing: Replace syscall_meta_data struct array with pointer array")
6549864629 ("tracepoints: Fix section alignment using pointer array")
e4a9ea5ee7 ("tracing: Replace trace_event struct array with pointer array")
Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.
Fixes: 99492c39f3 ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memblock_virt_alloc() works for both memblock and bootmem, so use it and
make early_init_dt_alloc_memory_arch a static function. The arches using
bootmem define early_init_dt_alloc_memory_arch as either:
__alloc_bootmem(size, align, __pa(MAX_DMA_ADDRESS))
or:
alloc_bootmem_align(size, align)
Both of these evaluate to the same thing as does memblock_virt_alloc for
bootmem. So we can disable the arch specific functions by making
early_init_dt_alloc_memory_arch static and they can be removed in
subsequent commits.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This wasn't documented.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
For static DT usecases, we don't need the disabled nodes and can skip
unflattening. This saves a significant amount of RAM in memory constrained
cases. In one example on STM32F469, the RAM usage goes from 118K to 26K.
There are a few cases in the kernel that modify the status property
dynamically. These all are changes from enabled to disabled, depend on
OF_DYNAMIC or are not FDT based (PDT based).
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add an equivalent function to of_device_is_available for flattened DT, and
convert the one existing open coded occurrence.
Tested-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
With dependencies on a statically allocated full path name converted to
use %pOF format specifier, we can store just the basename of node, and
the unflattening of the FDT can be simplified.
This commit will affect the remaining users of full_name. After
analyzing these users, the remaining cases should only change some print
messages. The main users of full_name are providing a name for struct
resource. The resource names shouldn't be important other than providing
/proc/iomem names.
We no longer distinguish between pre and post 0x10 dtb formats as either
a full path or basename will work. However, less than 0x10 formats have
been broken since the conversion to use libfdt (and no one has cared).
The conversion of the unflattening code to be non-recursive also broke
pre 0x10 formats as the populate_node function would return 0 in that
case.
Signed-off-by: Rob Herring <robh@kernel.org>
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
-----BEGIN PGP SIGNATURE-----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=DNwf
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
of: document /sys/firmware/fdt
dt-bindings: Add RISC-V vendor prefix
vsprintf: Add %p extension "%pOF" for device tree
of: find_node_by_full_name rewrite to compare each level
of: use kbasename instead of open coding
dt-bindings: thermal: add file extension to brcm,ns-thermal
of: update ePAPR references to point to Devicetree Specification
scripts/dtc: dtx_diff - Show real file names in diff header
of: detect invalid phandle in overlay
of: be consistent in form of file mode
of: make __of_attach_node() static
of: address.c header comment typo
of: fdt.c header comment typo
of: make of_fdt_is_compatible() static
dt-bindings: display-timing.txt convert non-ascii characters to ascii
Documentation: remove overlay-notes reference to non-existent file
dt-bindings: usb: exynos-usb: Add missing required VDD properties
dt-bindings: Add vendor prefix for Linksys
MAINTAINERS: add device tree ABI documentation file
of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
...
Fix typo in header comment for early_init_dt_scan_memory()
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The callers of of_fdt_is_compatible() are all in fdt.c so
make it static.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The memory allocator passed to __unflatten_device_tree() (e.g. a wrapped
kzalloc) can fail so add the missing sanity check to avoid dereferencing
a NULL pointer.
Fixes: fe14042358 ("of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree")
Cc: stable <stable@vger.kernel.org> # 2.6.38
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
Introduce primitives for FDT parsing. These will be used for powerpc
cpufeatures node scanning, which has quite complex structure but should
be processed early.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
sparse generates the following warnings in drivers/of/:
../drivers/of/fdt.c:63:36: warning: cast to restricted __be32
../drivers/of/fdt.c:68:33: warning: cast to restricted __be32
../drivers/of/irq.c:105:88: warning: incorrect type in initializer (different base types)
../drivers/of/irq.c:105:88: expected restricted __be32
../drivers/of/irq.c:105:88: got int
../drivers/of/irq.c:526:35: warning: incorrect type in assignment (different modifiers)
../drivers/of/irq.c:526:35: expected int ( *const [usertype] irq_init_cb )( ... )
../drivers/of/irq.c:526:35: got void const *const data
../drivers/of/of_reserved_mem.c:200:50: warning: incorrect type in initializer (different modifiers)
../drivers/of/of_reserved_mem.c:200:50: expected int ( *[usertype] initfn )( ... )
../drivers/of/of_reserved_mem.c:200:50: got void const *const data
../drivers/of/resolver.c:95:42: warning: incorrect type in assignment (different base types)
../drivers/of/resolver.c:95:42: expected unsigned int [unsigned] [usertype] <noident>
../drivers/of/resolver.c:95:42: got restricted __be32 [usertype] <noident>
All these are harmless type mismatches fixed by adjusting the types.
Signed-off-by: Rob Herring <robh@kernel.org>
Existing overlay unit tests examine individual pieces of the overlay
code. The new tests target the entire process of applying an overlay.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- Sync dtc to upstream commit 0931cea3ba20. This picks up overlay
support in dtc.
- Set dma_ops for reserved memory users.
- Make references to IOMMU consistent in DT bindings.
- Cleanup references to pm_power_off in bindings.
- Move some display bindings that snuck into the old bindings/video/
path.
- Fix some wrong documentation paths caused from binding restructuring.
- Vendor prefixes for Faraday and Fujitsu.
- Fix an of_node ref counting leak in of_find_node_opts_by_path
- Introduce new graph helper of_graph_get_remote_node() which will be
used by DRM drivers in 4.12.
-----BEGIN PGP SIGNATURE-----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=D/BO
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"Pretty standard stuff with dtc upstream sync being the biggest piece.
- Sync dtc to upstream commit 0931cea3ba20. This picks up overlay
support in dtc.
- Set dma_ops for reserved memory users.
- Make references to IOMMU consistent in DT bindings.
- Cleanup references to pm_power_off in bindings.
- Move some display bindings that snuck into the old bindings/video/
path.
- Fix some wrong documentation paths caused from binding
restructuring.
- Vendor prefixes for Faraday and Fujitsu.
- Fix an of_node ref counting leak in of_find_node_opts_by_path
- Introduce new graph helper of_graph_get_remote_node() which will be
used by DRM drivers in 4.12"
* tag 'devicetree-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (27 commits)
DT: add Faraday Tec. as vendor
of: introduce of_graph_get_remote_node
of: Add missing space at end of pr_fmt().
of: make of_device_make_bus_id() static
of: fix of_node leak caused in of_find_node_opts_by_path
dt-bindings: net: remove reference to fixed link support
dt-bindings: power: reset: qnap-poweroff: Drop reference to pm_power_off
dt-bindings: power: reset: gpio-poweroff: Drop reference to pm_power_off
dt-bindings: mfd: as3722: Drop reference to pm_power_off
dt-bindings: display: move ANX7814 and SiI8620 bridge bindings
of/unittest: Swap arguments of of_unittest_apply_overlay()
Documentation: usb: fix wrong documentation paths
serial: fsl-imx-uart.txt: Remove generic property
devicetree: Add Fujitsu Ltd. vendor prefix
Documentation: display: fix wrong documentation paths
of: remove redundant memset in overlay
bus:qcom : Fix typo in qcom,ebi2.txt
dt-bindings: qman: Remove pool channel node
Documentation: panel-dpi: fix path to display-timing.txt
devicetree: bindings: clk: mvebu: fix description for sata1 on Armada XP
...
Make pr_fmt() in fdt.c consistent with all other files in drivers/of/
Signed-off-by: Frank Rowand <frank.rowand@am.sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
An empty __dtb_start to __dtb_end section might result in
initial_boot_params being null for arch/mips/ralink. This showed that the
boot process hangs indefinitely in of_scan_flat_dt().
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14605/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When movable nodes are enabled, any node containing only hotpluggable
memory is made movable at boot time.
On x86, hotpluggable memory is discovered by parsing the ACPI SRAT,
making corresponding calls to memblock_mark_hotplug().
If we introduce a dt property to describe memory as hotpluggable,
configs supporting early fdt may then also do this marking and use
movable nodes.
Link: http://lkml.kernel.org/r/1479160961-25840-5-git-send-email-arbab@linux.vnet.ibm.com
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alistair Popple <apopple@au1.ibm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have multiple "earlycon" early_param handlers - merge the DT one into
the main earlycon one. It's a cleanup that also will be useful
to defer setting up DT console until ACPI/DT decision is made.
Rename the exported function to avoid clashing with the function from
arch/microblaze/kernel/prom.c
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
@mynodes is set to NULL when __unflatten_device_tree() is called
to unflatten device sub-tree in PCI hot add scenario on PowerPC
PowerNV platform. Marking @mynodes detached unconditionally causes
kernel crash as below backtrace shows:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000b26f64
cpu 0x0: Vector: 300 (Data Access) at [c000003fcc7cf740]
pc: c000000000b26f64: __unflatten_device_tree+0xf4/0x190
lr: c000000000b26f40: __unflatten_device_tree+0xd0/0x190
sp: c000003fcc7cf9c0
msr: 900000000280b033
dar: 0
dsisr: 40000000
current = 0xc000003fcc281680
paca = 0xc00000000ff00000 softe: 0 irq_happened: 0x01
pid = 2724, comm = sh
Linux version 4.7.0-gavin-07754-g92a6836 (gwshan@gwshan) (gcc version \
4.9.3 (Buildroot 2016.02-rc2-00093-g5ea3bce) ) #539 SMP Mon Aug 1 \
12:40:29 AEST 2016
enter ? for help
[c000003fcc7cfa50] c000000000b27060 of_fdt_unflatten_tree+0x60/0x90
[c000003fcc7cfaa0] c0000000004c6288 pnv_php_set_slot_power_state+0x118/0x440
[c000003fcc7cfb80] c0000000004c6a10 pnv_php_enable+0xc0/0x170
[c000003fcc7cfbd0] c0000000004c4d80 power_write_file+0xa0/0x190
[c000003fcc7cfc50] c0000000004be93c pci_slot_attr_store+0x3c/0x60
[c000003fcc7cfc70] c0000000002d3fd4 sysfs_kf_write+0x94/0xc0
[c000003fcc7cfcb0] c0000000002d2c30 kernfs_fop_write+0x180/0x260
[c000003fcc7cfd00] c000000000230fe0 __vfs_write+0x40/0x190
[c000003fcc7cfd90] c000000000232278 vfs_write+0xc8/0x240
[c000003fcc7cfde0] c000000000233d90 SyS_write+0x60/0x110
[c000003fcc7cfe30] c000000000009524 system_call+0x38/0x108
This avoids the kernel crash by marking @mynodes detached only when
@mynodes is dereferencing valid device node in __unflatten_device_tree().
Fixes: 1d1bde550e ("of: fdt: mark unflattened tree as detached")
Reported-by: Meng Li <shlimeng@cn.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXm9KcAAoJEPr7XbWNvGHDRT4QAIIIOSB4AWHardnMLROgGge9
aOQKZ/05O9feOcxYKe8FkQbcH+IujJjrUL+yrRD36yGQPAyBP21gtcmmfrkCcwFM
kH915f/JbGvXpfwEf8dcarHhzYH6FFJiQGduPpWfwSSWynx+xq5EKPwCqYzMg8bN
SExxt7vUx1MKFOExZ0K8BNCo8VMVLUWQoJ1DNeJDuL25Op4EU3i2l1HQNYV/3XDk
BSA3x7Lw3GjrWEH20VWYn2Azq1OFLY+E2FC2lnG4nbkk5X8dZbUH9PR1Sk7uTQDj
uxTjWe59NBpliCxKSAbMbTAU/WwSB1pJ0I+zDJBiQsdFT+nb5F4zOrs3qSKHa/A9
Rv6AC8k5gdSMrDB1dOspfF2vWvOOInXgNV4/Kza0D92mbCpwyUuF+vhE6rfcMrZU
OiD7rj2/fvO7Y9fUAhrp6zrfrOfH9B1Z9vS+940AlK96YwPE2+J0SA2vBxR/wg8H
7fj4Ud5X+SFisXWQhh5Wlv0W9o6e7C7fsi8vpkQ7gufmezLFWVnJKsUfQaxGEwhG
Hkhm9kuSHHMd+6dEnn2756DnNfJAtQv6rSR0/QR4Lf9y5L4dvR3kAQIci8X/nx4P
sIk+IJWGZG6wziZq59hh+SO6HEqdSNuvh+5sbR0iUimdE/1HsDBdPiocXf/r8iwK
NY9nGeZPRrXmFgdpoZfm
=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Nicolas Boichat