This patch addresses a couple of cases where I forgot to pop open the
gate when in analog mode (a correlary to fix the change made in patch
1c58d5b4a5fca42dce5428bd79b9405878017735).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver prints out a dotted version number but it's in hex. As a
result, the version doesn't visibly match the filename for the firmware,
and it caused a bunch of confusion while discussing different versions
with the chip manufacturer.
Change the firmware printout to be in decimal.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hack I put in a couple of years ago to avoid clock stretching issues
when talking to the xc5000 worked fine for writes, but intermittently
fails for register reads, because the xc5000 may stretch the clock for
longer between bytes (I was seeing cases of 21 us on the analyzer).
The problem manifested itself as the xc5000 firmware version and PLL
lock register intermittently showing garbage values.
Slow down the i2c bus from 30 KHz to 20 KHz to accommodate.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000c and newer versions of the xc5000a firmware need minor revisions
to their initialization process. Add support for validating the firmware
was properly loaded, as well as checking the init status after initialization.
Based on advice from CrestaTech support as well as xc5000 datasheet v2.3.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's possible for the xc5000 to enter an unknown state such that all
subsequent tuning requests fail. The only way to recover is to reset the
tuner and reload the firmware. This problem was detected after several days
straight of issuing tuning requests every five seconds.
Reset the firmware in the event that the PLL is in an unlocked state. This
solution was provided by the engineer at CrestaTech (the company that acquired
Xceive).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjust the retry timeout and number of retries to speed up xc5000
firmware download. With this change it goes from 4.2 seconds to 2.9.
The net time waited is pretty much the same, but we just poll more
often.
Tested at 250 KHz as well as 30 KHz.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are no cases where a control message is ever sent to the au0828
with an actual buffer defined. Remove the reference to dev->ctrlmsg,
which currently requires us to hold a mutex since it is shared with the
read function.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put a hack in place to speed up the firmware load in the case that the
xc5000 has just been reset. The chip can safely do 400 KHz in this mode,
while in normal operation it can only do 100 KHz.
This reduces the firmware load time from 6.9 seconds to 4.2.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We weren't checking whether the resource was in use before calling
res_free(), so applications which called STREAMOFF on a v4l2 device that
wasn't already streaming would cause a BUG() to be hit (MythTV).
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Reported-by: Jay Harbeston <jharbestonus@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original implementation of the analog support would use an
i2c_gate_ctrl function when using the digital side of the au8522, but on
the analog side we would always just force the gate open and leave it
open all the time.
This can have adverse effects on the xc5000 given the tuner is receiving
all the spurious i2c traffic (a problem which can be exaggerated due to
bugs in the au0828 i2c hardware implementation).
Rework the existing hack to only open/close the gate when actually
talking to the tuner.
This logic might need to be reworked a bit if anybody ever tries to add
support for a board that has the au0828/au8522 but doesn't have digital
support implemented (because the i2c_gate_ctrl callback is being set in
the DVB attach). However given how few different models are in
circulation, this can be deferred until such a situation arises (if
ever).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code invokes the auto calibration of the tuner whenever the
init routine is called (whenever the DVB frontend opens the device).
However we should really only be invoking the calibration if we actually
did reset the device and reload the firmware.
Rework the routine to only do calibration if reset and firmware load was
performed. Also because the called function is now a no-op if the
firmware is already loaded, the caller no longer needs to invoke
is_firmware_loaded().
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au8522 driver was broken into three modules (dig, decoder, common),
and as a result the debug modprobe option doesn't work for any of the
common functions.
Copy the module macros over to the common module so that the debug
option works again.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the user performs a tuning attempt without explicitly calling the
s_std ioctl(), a value of zero is sent from tuner-core to xc5000. This
causes the xc5000 driver to leave the standard unchanged. The problem
was masked by the fact that the xc5000 driver defaulted to NTSC, but if
you happened to perform an ATSC/ClearQAM tuning attempt and then do an
analog tune, the net effect is an analog tune with the standard still
set to DTV6.
Keep track of whether the standard has ever been sent to tuner-core. We
don't make an s_std subdev call explicitly during probe because that
will cause a firmware load (which is very time consuming on the 950q).
With the logic in this patch, the s_std call will occur automatically on
the s_freq call if it hasn't already been set.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases users would see the xc5000_attach() call failing for the
digital side of the tuner on initialization. This is because of udev
running v4l-id while the digital side of the board is still coming up.
This is the exact same race condition which was present in em28xx (not
surprising since I copied all the locking logic from that driver when I
added analog support). Reproduce Mauro's fix from the em28xx driver in
au0828.
Reported-by: Rick Harding <rharding@mitechie.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic as written would *never* actually return an error condition,
since the loop would run until the counter hit zero but the check was
for a value less than zero.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When debugging is enabled, also show the analog SNR and the total gain
status values.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The quality register only has relevant data in bits 2-0, so discard the
other bits (which results in a value being printed that is consistent
with the expected 0-7 range).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The g_reg and s_reg calls worked properly if acting on subdev registers
(such as the au8522), but didn't work against the au0828 itself. Copy
the logic over from em28xx.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is an apparent bug in the au8522 TS clocking which can result in
it delivering a TS payload to the au0828 that is shifted by some number
of bits. For example, the device will announce a packet containing "FA
38 FF F8" which if you shift left one bit is "1F 47 1F FF F0..."
This presents itself as no TS stream being delivered from the kernel to
userland, since the kernel demux will drop every packet.
In the event that this condition occurs, restart the DVB stream.
Also, this patch includes a couple of lines of cleanup to not change the
FIFO configuration while the FIFO is running (which can screw up the
state machine), and dequeue the buffers before turning off the FIFO.
This puts the logic in sync with the Windows driver.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The table of valid SNR values for QAM 256 is off by one, and as a result
if the SNR is oscillating between 40.0 and 39.9 dB, tools like azap show
it going back and forth between 40.0 and 0 (misleading some people,
including myself, to think signal lock is being lost or there is a
problem with register reads).
Fix the table so that 40.0 dB is properly represented.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turns up the autodetection for the video standard in the au8522 is
prone to hanging the chip until a reset is performed. This condition is
trivial to reproduce simply by tuning to a station and then rapidly
unplugging/ replugging the coax feed.
Because we've never claimed to support anything other than NTSC-M, just
disable the video-standard autodetection logic and force it to always be
NTSC-M.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that needed V4L2_FL_LOCK_ALL_FOPS have been converted,
so remove this flag altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
I also removed some dead code in the form of the saa7146_devices list and
saa7146_devices_lock mutex: these were used once but that was a long time
ago.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add proper locking to the file operations, allowing for the removal
of the V4L2_FL_LOCK_ALL_FOPS flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dvb-usb-v2 core doesn't know anything about CI. So, the
driver needs to handle it by hand. This patch stops CI just
before stopping URB's/RC, and restarts it before URB/RC start.
It should be noticed that suspend/resume is not yet working properly,
as the PM model requires the implementation of reset_resume:
dvb_usb_az6007 1-6:1.0: no reset_resume for driver dvb_usb_az6007?
But this is not implemented there at dvb-usb-v2 yet.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for I2C W+R will never be true. Fix it.
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change it to use dvb-usb-v2. The driver should be working as before.
The only functional changes should be at the driver debug logs.
This driver needs the cypress firmware load, so, auto-selects it.
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dvb-usb-v2 cypress firmware module is not optional, as drivers
won't work without it. So, instead of opening a menu for the user to
manually select, let the drivers that need it to select, hiding this
option from the Kconfig menu.
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ERROR: "usbv2_cypress_load_firmware" [drivers/media/dvb/dvb-usb-v2/dvb-usb-az6007.ko] undefined!
Cypress fimware will never be compiled properly, as the Makefile rule
is wrong.
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver wasn't converted to the new clock framework
(e038ed50a4).
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/m2m-deinterlace.c: In function ‘deinterlace_issue_dma’:
drivers/media/video/m2m-deinterlace.c:363:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’ [-Wformat]
drivers/media/video/m2m-deinterlace.c:363:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 5 has type ‘dma_addr_t’ [-Wformat]
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some video decoders such as tvp5150 provide separate
video fields (V4L2_FIELD_SEQ_TB/BT). This driver uses
dmaengine to convert this format to V4L2_FIELD_INTERLACED_TB/BT
(weaving) or V4L2_FIELD_NONE (line doubling) so that the
image can be displayed or processed.
Of course there will be combing effect in the image but this
can be accepted for some low quality applications.
Currently only YUV420 and YUYV formats are supported but
it can be extended later.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Coda is a range of video codecs from Chips&Media that
support H.264, H.263, MPEG4 and other video standards.
Currently only support for the codadx6 included in the
i.MX27 SoC is added. H.264 and MPEG4 video encoding
are the only supported capabilities by now.
[mchehab@redhat.com: Add missing include linux/of.h]
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Reviewed-by: Philipp Zabel<p.zabel@pengutronix.de>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this header were meant to be used just by dvb-usb driver, it
is now being used also by dvb-usb-v2 and cx231xx. So, move it to a
better place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1)
AF9015 remote controller query will fail rarely due to register
access failures and dvb_usb_v2 will stop rc polling when error
returned. Add logic to allow errors until two consecutive errors
occurs.
2)
Remote controller key map was not loaded in case of key map was set as
a device property. Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It failed to register device when remote keymap was not set.
Fix it to register device even keymap is NULL. In that case
just skip remote registration.
Driver should set RC_MAP_EMPTY to enable remote in case of
there is remote receiver but default keymap is unknown.
Reported-by: pierigno <pierigno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It works no longer as it was designed since we can change streaming
configuration during device operation.
Maybe it should be performed conditionally on cases when streaming
endpoint is changed. Anyhow, let it out now and add later if needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check that adapter exists before trying to remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pass frontend instead of adapter as some drivers need to make
decisions based frontend.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was left from the legacy remote controller we do not support.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Comment briefly all used structures and variables.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is nice to have this debug, but as it generates very huge amount
of traffic, better to make it conditional. Use define macro to disable
it as I did not find out how to use dynamic debugs to dump variable
length buffers like that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge files dvb_usb_init.c and dvb_usb_dvb.c to dvb_usb_core.c.
It is still under 1000 lines of code after all the optimization
so put it one file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can live easily without it so remove it, make code and binary
few bytes smaller.
>From struct dvb_usb_device variable int num_adapters_initialized.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Merge get_firmware_name() to identify_state().
It is wise to resolve firmware name in that routine as it does
decision wether or not to load firmware at all. It is one very
rarely needed callback less.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Piggypag TS type callback to USB stream callback and change
callback name slightly to fit better.
Both of those are rather rare callback and has a relation. Transport
Stream, TS, is input stream and USB stream is output stream of
DVB USB bridge.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We dont need that pointer as we can use container_of() macro thus
remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can live without it easily.
Also USB data stream complete callback checks for feedcount
seems to be quite redundant so remove those also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was synchronization problem when streaming was stopped.
Frontend was ran down before stream which causes problems.
Use mutex to synchronization. Now it looks like that:
LOCK
start frontend
UNLOCK
LOCK
start streaming
[...]
stop streaming
UNLOCK
LOCK
stop frontend
UNLOCK
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial / default USB stream configuration is now set always as a
dvb_usb_device_properties. Dynamic configuration is done top of
that if callback .get_usb_stream_config() exists. Default values
are set when callback is called so callback needs only change
values that are different than default.
In addition of that define two macros DVB_USB_STREAM_BULK() and
DVB_USB_STREAM_ISOC() for filling struct usb_data_stream_properties
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Give DVB adapter as a parameter for callback. MAC address is
adapter property and it could be (at least in theory) there
is devices having multiple adapters and all has own MAC.
Also add error handling. If callback fails error is returned
which leads device unregister.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove state from struct dvb_usb_device as we can live without.
Add some debug logs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It did not removed adapter on error case as .num_adapters_initialized
was set after success adapter initialization. It should be safe to
try remove all possible adapters in any-case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USB core will call disconnect and remove driver for us as device
will disconnect itself. After that it is loaded again as a new
device but it is warm and no firmware loading needed.
Reported-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first being this patch, no return value from dvb_usb_download_firmware
causes system wide dead lock with COLD disconnect as system attempts to continue
to warm state.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is more than nice to have all those frontend pointers when
attaching tuner to the frontend in question. Make that possible
attaching tuners after dvb_register_frontend()
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Small changes like log writings. No functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is only three functions so move it to the main.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not check active frontend as it could be already shutdown.
Add some more debugs.
It turns out that device is put sleep earlier than streaming
is stopped in some cases. That is because streaming is running
different task and there is no locking.
Maybe some locking could be good idea to force stop streaming
before device is shut down. I can guess there could be problems
in someday cases like chip is sleep but streaming control is
requested after that...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change logging.
Some minor text and error number changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use pointers to properties as device and adapter properties are
constant. No need to embed and copy those structures.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move frontend_attach, tuner_attach, frontend_ctrl and streaming_ctrl
from adapter to device.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware handling routines for various Cypress chips.
Cypress AN2135
Cypress AN2235
Cypress FX2
These were split out from general DVB USB module by
Patrick Boettcher. I did only small changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop remote polling and USB streaming before suspend and resume
those when back to normal operation.
It is far away from complete implementation, but at least it does
not hang system anymore on suspend while streaming is ongoing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In my understanding we never call .disconnect() when .probe()
returns error. Change .probe() to return error all cases it cannot
handle given interface and simplify .disconnect() handling.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I think it is better to allow driver finish pending operations and
disconnect device. Killing all ongoing USB transfers could have very
bad effect, even break hardware in worst case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Almost all hacks are now removed and much less code.
Reducing af9015 driver code from 2084 to 1609, it is almost
500 LOC less!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compilation was disabled as it was failing with allyesconfig.
Rename duplicate functions and enable building.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was possible to free resources by unloading module while
initialization was still ongoing on delayed work.
Use PID to make decision on .disconnect() if caller is our
work or some other as work also calls .disconnect() in error
case. There could be better solution still...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Debug prints write operation data instead of read data was
intention.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no USB match flag for used USB interface. It is rather
common there is multiple interfaces offering different services.
For example one for television and one for remote controller.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No worth to keep it on own file as it is only 30 LOC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use Kernel logging insteads of own macros.
Get rid of old debugs and use dynamic debug.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unregister all if there is any error meet during
frontend initialization.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling usb_clear_halt() during device init is not correct.
2 of 7 AF9015 devices I have timeouts next USB control message
after usb_clear_halt(). It was originally performed between
tuner_attach() and rc_query() and likely not causing problems
since rc_query() is repeated continously. None could see it when
first rc_query() failed...
Secondly it was not called for .generic_bulk_ctrl_endpoint_response.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move work to the struct dvb_usb_device that we can access
it inside .disconnect().
Also many other minor changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It could be null in case of driver does not set it
properly, like missing dynamic ID handling.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adapter priv is not really needed, use device priv instead.
There is only driver or two using that.
Device caps are not needed. There was only "has I2C adapter"
capability defined. It is useless as we can see same just
checking existence of i2c_algo callback.
And also remove some totally not used at all variables.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove Cypress USB-interface firmware downloading routines.
That is common module and having single vendor chip routines
in common module is wrong. Just move those elsewhere.
Move single function out from the dvb_usb_firmware.c and
remove that file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delay firmware download and whole driver initialization using
workqueue. udev causes problems when blocking firmware download
was done during module init. This will likely resolve all
DVB USB firmware downloading issues we have had during recent years.
Fixes bug in case of DVB USB driver:
https://bugzilla.redhat.com/show_bug.cgi?id=827538
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed because all frontends are attached as a one go.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of (struct dvb_usb_adapter_fe_properties) as we no longer
need it. Frontends are now defined as a array of pointers inside
adapter struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move .frontend_attach(), .tuner_attach() and .streaming_ctrl()
from the frontend to adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Filtering given PIDs from the transport stream is done by the
DVB USB bridge. It is highly possible there is limitations what
kind of stream DVB USB bridge can PID filter, but it still does
not make sense to define filters for each frontend as frontend
could offer different stream types for different standards.
Likely new way is to enable / disable PID filters are needed to
make decision at runtime (callback). PID filters are quite legacy
stuff as those are aimed cut stream smaller to fit for the USB1.1...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move USB stream properties from frontend to adapter.
It is property of adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new callback in order to resolve used TS (MPEG transport stream)
configuration. Normal TS is 188 byte payload only but there is
currently 204 byte TS and raw TS supported too.
Traditionally TS type was mapped as a frontend property but it
does not work no longer after we changed from MFE (multi-frontend)
to SFE (single-frontend). So it is not possible to map TS for the
given FE as there could be only one FE instead of multiple.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move stream from the frontend to adapter. There could be only
one stream per adapter. One adapter can has multiple frontends
but only one can stream at the time.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New callback to resolve current USB stream configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller