Convert list_for_each() to list_for_each_entry() where
applicable. This simplifies the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->plat->mdio_bus_data is optional, some platforms may not set it,
however we proceed to look straight at priv->plat->mdio_bus_data->has_xpcs.
Since the xpcs is instantiated based on the has_xpcs property, we can
avoid looking at the priv->plat->mdio_bus_data structure altogether and
just check for the presence of the xpcs pointer.
Fixes: 11059740e6 ("net: pcs: xpcs: convert to phylink_pcs_ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert list_for_each() to list_for_each_entry() where
applicable. This simplifies the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert list_for_each() to list_for_each_entry() where
applicable. This simplifies the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert list_for_each() to list_for_each_entry() where
applicable. This simplifies the code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang says:
====================
net: hns3: add RAS compatibility adaptation solution
This patchset adds RAS compatibility adaptation solution for new devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, the driver logs and clears the hw errors that
already occurred. For device supports imp-handle ras capability, it
needs handle different error status, otherwise it may cause wrong reset.
So fix it by adding a new processing branch.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update error recovery module and type for RoCE.
The enumeration values of module names and error types are not sorted
in sequence. If use the current printing mode, they cannot be correctly
printed.
Use the index mode, If mod_id and type_id match the enumerated value,
display the corresponding information.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IMP(Intelligent Management Processor) firmware add a new feature to
handle and consolidate RAS information for new devices, NIC driver
only needs to query the reported RAS information. NIC driver adds
support for this feature.
Driver queries device capability to check whether IMP support this
feature, If yes, execute the new RAS processing branch.
In order to add a method to check whether PF supports imp-handle RAS
feature, add dumping this info in debugfs.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To adapt to hardware modification and ensure that the driver is
compatible with the original error handling content, we need to add the
RAS compatibility adaptation solution.
Add a processing branch to the driver during error handling. In the new
processing branch, NIC fault information is integrated by the IMP. An
interaction command is added between the driver and IMP to query
and clear the fault source and interrupt source. The IMP integrates
error information and reports the highest reset level to the driver.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, hardware errors can be reported through AER or MSI-X mode.
However, the AER mode is intended to handle only bus errors, but not
hardware errors. On the other hand, virtual machines cannot handle
AER errors. When an AER error is reported, virtual machines will be
suspended. So add support for handling all these hardware errors
through MSI-X mode which depends on a newer version of firmware,
and reserve the handler of the AER mode for compatibility.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shay Agroskin says:
====================
se build_skb and reorganize some code in ENA
this patchset introduces several changes:
- Use build_skb() on RX side.
This allows to ensure that the headers are in the linear part
- Batch some code into functions and remove some of the code to make it more
readable and less error prone
- Fix RST format and outdated description in ENA documentation
- Improve cache alignment in the code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure some ethtool to a switch-case blocks to make it more uniform
with other similar functions.
Also restructure variable declaration to create reversed x-mas tree.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_alloc() when allocating RX buffers instead of specifying the
allocation flags explicitly. This result in same behaviour with less
code.
Also move the page allocation and its DMA mapping into a function. This
creates a logical block, which may help understanding the code.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena_ring_tx_doorbell() is introduced to call the doorbell and
increase the driver's corresponding stat.
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation file used to be written in markdown format but was
converted to reStructuredText (rst).
The converted file doesn't keep up with rst format requirements which
results in hard-to-read text.
This patch fixes the formatting of the file. The patch also
* Highlights and emphasizes some lines to improve readability
* Rephrases some hard-to-understand text
* Updates outdated function descriptions.
* Removes TSO description which falsely claims the driver supports it
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the module param 'debug' which allows to specify the message
level of the driver. This value can be specified using ethtool command.
Also reduce the message level of LLQ support to be a warning since it is
not an indication of an error.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are instances when we want to know when the last napi was
called for debugging.
On stuck / heavy loaded CPUs, the ena napi handler might not be
called for a long period of time. This stat can help us to
determine how much time passed since the last execution of napi.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the RX path to use build_skb() for packets larger
than copybreak (set to 256 by default). This function makes the first
descriptor's page to be the linear part of the sk_buff struct buffer.
Also remove the SKB description from the README since most of it no
longer relevant and the parts that are left don't add information.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add prints to improve logging of driver's errors.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA_DEFAULT_MIN_RX_BUFF_ALLOC_SIZE macro,
ena_xdp_queues_present() function and SUSPEND_RESUME enums aren't used
in the driver, and so not needed.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tweaks several small places to improve the data access in fast
path:
* Remove duplicates of first_interrupt flag and surround it with
WRITE/READ_ONCE macros:
The flag is used to detect HW disorders in its
interrupt communication with the driver. The flag is set when an
interrupt is received and used in the health check function
(ena_timer_service()) to help it find irregularities.
* Reorder some fields in ena_napi struct to take better advantage of
cache access pattern.
* Move XDP TX queue number to a variable to save its calculation for
every packet.
* Use likely in a condition to improve branch prediction
The 'first_interrupt' and 'interrupt_masked' flags were moved to reside
in the same cache line as the first fields of 'napi' struct. This
placement ensures that all memory accessed during upper-half handler
reside in the same cacheline (napi_schedule_irqoff() only accesses
'state' and 'poll_list' fields which are at the beginning of napi
struct).
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Various updates
This patchset contains various updates for mlxsw. The most significant
change is the long overdue removal of the abort mechanism in the first
two patches.
Patches #1-#2 remove the route abort mechanism. This change is long
overdue and explained in detail in the commit message.
Patch #3 sets ports down in a few selftests that forgot to do so.
Discovered using a BPF tool (WIP) that monitors ASIC resources.
Patch #4 fixes an issue introduced by commit 557c4d2f78 ("selftests:
devlink_lib: add check for devlink device existence").
Patches #5-#8 modify the driver to read transceiver module's temperature
thresholds using MTMP register (when supported) instead of directly from
the module's EEPROM using MCIA register. This is both more reliable and
more efficient as now the module's temperature and thresholds are read
using one transaction instead of three.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_thermal_module_trips_update() is used to update the trip points of
the module's thermal zone. Currently, this is done by querying the
thresholds from the module's EEPROM via MCIA register. This data does
not pass validation and in some cases can be unreliable. For example,
due to some problem with transceiver module.
Previous patch made it possible to read module's temperature and
thresholds via MTMP register. Therefore, extend
mlxsw_thermal_module_trips_update() to use the thresholds queried from
MTMP, if valid.
This is both more reliable and more efficient than current method, as
temperature and thresholds are queried in one transaction instead of
three. This is significant when working over a slow bus such as I2C.
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide new function mlxsw_thermal_module_temp_and_thresholds_get() for
reading temperature and temperature thresholds by a single operation.
The motivation is to reduce the number of transactions with the device
which is important when operating over a slow bus such as I2C.
Currently, the sole caller of the function is only using it to read the
module's temperature. The next patch will also use it to query the
module's temperature thresholds.
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, module temperature thresholds are obtained from Management
Cable Info Access (MCIA) register by specifying the thresholds offsets
within module EEPROM layout. This data does not pass validation and in
some cases can be unreliable. For example, due to some problem with the
module.
Add support for a new feature provided by Management Temperature (MTMP)
register for sanitization of temperature thresholds values.
Extend mlxsw_env_module_temp_thresholds_get() to get temperature
thresholds through MTMP field 'max_operational_temperature' - if it is
not zero, feature is supported. Otherwise fallback to old method and get
the thresholds through MCIA.
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend Management Temperature (MTMP) register with new field specifying
the maximum temperature threshold.
Extend mlxsw_reg_mtmp_unpack() function with two extra arguments,
providing high and maximum temperature thresholds. For modules, these
thresholds correspond to critical and emergency thresholds that are read
from the module's EEPROM.
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f78 ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several tests do not set some ports down as part of their cleanup(),
resulting in IPv6 link-local addresses and associated routes not being
deleted.
These leaks were found using a BPF tool that monitors ASIC resources.
Solve this by setting the ports down at the end of the tests.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To check how many routes are installed in hardware, the test runs "ip
route" and greps for "offload", which includes routes with state
"offload_failed".
Till now, this wrong check was not found because after one failure in
route insertion, the driver moved to "abort" mode, which means that user
cannot try to add more routes.
The previous patch removed the abort mechanism and now failed routes are
counted as offloaded.
Fix this by not considering routes with "offload_failed" flag as
offloaded.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The abort mechanism was introduced in commit 8e05fd7166 ("fib: hook
IPv4 fib for hardware offload") with the purpose of falling back to
software-based routing in case of a route programming error in hardware.
The process is irreversible and requires users to reload the offloading
driver or reboot the machine.
While this approach might make sense in theory, it makes very little
sense in practice. In the case of high speed ASICs such as the Spectrum
ASIC, the abort mechanism effectively kills the machine upon a non-fatal
error such as a route programming error.
Such an extreme policy does not belong in the kernel, especially when
user space can simply try to reprogram the route following the
RTM_NEWROUTE failure notification.
Therefore, remove the abort mechanism.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Add NXP SJA1110 support to the sja1105 DSA driver
The NXP SJA1110 is an automotive Ethernet switch with an embedded Arm
Cortex-M7 microcontroller. The switch has 11 ports (10 external + one
for the DSA-style connection to the microcontroller).
The microcontroller can be disabled and the switch can be controlled
over SPI, a la SJA1105 - this is how this driver handles things.
There are some integrated NXP PHYs (100base-T1 and 100base-TX). Their
initialization is handled by their own PHY drivers, the switch is only
concerned with enabling register accesses to them, by registering two
MDIO buses.
Changes in v3:
- Make sure the VLAN retagging port is enabled and functional
- Dropped SGMII PCS from this series
Changes in v2:
- converted nxp,sja1105 DT bindings to YAML
- registered the PCS MDIO bus and forced auto-probing off for all PHY
addresses for this bus
- changed the container node name for the 2 MDIO buses from "mdio" to
"mdios" to avoid matching on the mdio.yaml schema (it's just a
container node, not an MDIO bus)
- fixed an uninitialized "offset" variable usage in
sja1110_pcs_mdio_{read,write}
- using the mdiobus_c45_addr macro instead of open-coding that operation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 contains two types of integrated PHYs: one 100base-TX PHY
and multiple 100base-T1 PHYs.
The access procedure for the 100base-T1 PHYs is also different than it
is for the 100base-TX one. So we register 2 MDIO buses, one for the
base-TX and the other for the base-T1. Each bus has an OF node which is
a child of the "mdio" subnode of the switch, and they are recognized by
compatible string.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has an extra configuration in the General Parameters Table
through which the user can select the buffer reservation config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 is basically an SJA1105 with more ports, some integrated
PHYs (100base-T1 and 100base-TX) and an embedded microcontroller which
can be disabled, and the switch core can be controlled by a host running
Linux, over SPI.
This patch contains:
- the static and dynamic config packing functions, for the tables that
are common with SJA1105
- one more static config tables which is "unique" to the SJA1110
(actually it is a rehash of stuff that was placed somewhere else in
SJA1105): the PCP Remapping Table
- a reset and clock configuration procedure for the SJA1110 switch.
This resets just the switch subsystem, and gates off the clock which
powers on the embedded microcontroller.
- an RGMII delay configuration procedure for SJA1110, which is very
similar to SJA1105, but different enough for us to be unable to reuse
it (this is a pattern that repeats itself)
- some adaptations to dynamic config table entries which are no longer
programmed in the same way. For example, to delete a VLAN, you used to
write an entry through the dynamic reconfiguration interface with the
desired VLAN ID, and with the VALIDENT bit set to false. Now, the VLAN
table entries contain a TYPE_ENTRY field, which must be set to zero
(in a backwards-incompatible way) in order for the entry to be deleted,
or to some other entry for the VLAN to match "inner tagged" or "outer
tagged" packets.
- a similar thing for the static config: the xMII Mode Parameters Table
encoding for SGMII and MII (the latter just when attached to a
100base-TX PHY) just isn't what it used to be in SJA1105. They are
identical, except there is an extra "special" bit which needs to be
set. Set it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 variations of the SJA1110 switch which have a different set
of MII protocols supported per port. Document the compatible strings.
Also, the SJA1110 optionally supports 2 internal MDIO buses for 2
different types of Ethernet PHYs. Document a container node called
"mdios" which has 2 subnodes "mdio@0" and "mdio@1", identifiable via
compatible string, under which the driver finds the internal PHYs.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey Ryazanov says:
====================
net: WWAN subsystem improvements
While working on WWAN netdev creation support, I notice a few things
that could be done to make the wwan subsystem more developer and user
friendly. This series implements them.
The series begins with a WWAN HW simulator designed simplify testing
and make the WWAN subsystem available for a wider audience. The next two
patches are intended to make the code a bit more clearer. This is
followed by a few patches to make the port device naming more
user-friendly. The series is finishes with a set of changes that allow
the WWAN AT port to be used with terminal emulation software.
All changes were tested with the HW simulator that was introduced in
this series, as well as with a Huawei E3372 LTE modem (a CDC-NCM
device), which I finally found on my desk.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Purge the rx queue as soon as a user closes the port, just after the
port stop callback invocation. This is to prevent feeding a user that
will open the port next time with outdated and possibly unrelated
data.
While at it also remove the odd skb_queue_purge() call in the port
device destroy callback. The queue will be purged just before the
callback is ivoncated in the wwan_remove_port() function.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not unreasonable to assume that users will use terminal emulation
software to communicate directly with a WWAN device over the AT port.
But terminal emulators will refuse to work with a device that does not
support terminal IOCTLs (e.g. TCGETS, TCSETS, TIOCMSET, etc.). To make
it possible to interact with the WWAN AT port using a terminal emulator,
implement a minimal set of terminal IOCTLs.
The implementation is rather stub, no passed data are actually used to
control a port behaviour. An obtained configuration is kept inside the
port structure and returned back by a request. The latter is done to
fool a program that will test the configuration status by comparing the
readed back data from the device with earlier configured ones.
Tested with fresh versions of minicom and picocom terminal apps.
MBIM, QMI and other ports for binary protocols can hardly be considered
a terminal device, so terminal IOCTLs are only implemented for the AT
port.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite common for a userpace program to fetch the buffered amount
of data in the rx queue to avoid the read block. Implement the TIOCINQ
ioctl to make the migration to the WWAN port usage smooth.
Despite the fact that the read call will return no more data than the
size of a first skb in the queue, TIOCINQ returns the entire amount of
buffered data (sum of all queued skbs). This is done to prevent the
breaking of programs that optimize reading, avoiding it if the buffered
amount of data is too small.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we limit the total ports number to 256. It is quite common
for PBX or SMS gateway to be equipped with a lot of modems. In now days,
a modem could have 2-4 control ports or even more, what only accelerates
the ports exhausing rate.
To avoid facing the port number limitation issue reports, increase the
limit up the maximum number of minors (i.e. up to 1 << MINORBITS).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, the port name is allocated based on the parent device
name, port id and the port type. Where the port id specifies nothing but
the ports registration order and is only used to make the port name
unique.
Most likely, to configure a WWAN device, the user will look for a port
of a specific type (e.g. AT port or MBIM port, etc.). The current naming
scheme can make it difficult to find a port of a specific type.
Consider a WWAN device that has 3 ports: AT port, MBIM port, and another
one AT port. With the global port index, the port names will be:
* wwan0p1at
* wwan0p2mbim
* wwan0p3at
To find the MBIM port, user should know in advance the device ports
composition (i.e. the user should know that the MBIM port is the 2nd
one) or carefully examine the whole ports list. It is not unusual for
USB modems to have a different composition, even if they are build on a
same chipset. Moreover, some modems able to change the ports composition
based on the user's configuration. All this makes port names fully
unpredictable.
To make naming more user-friendly, remove the global port id and
enumerate ports by its type. E.g.:
* wwan0p1at -> wwan0at0
* wwan0p2mbim -> wwan0mbim0
* wwan0p3at -> wwan0at1
With this naming scheme, the first AT port name will always be wwanXat0,
the first MBIM port name will always be wwanXmbim0, etc.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually a device name is spelled in lowercase, let us follow this
practice in the WWAN subsystem as well. The bottom line is that such
name is easier to type.
To keep the device type attribute contents more natural (i.e., spell
abbreviations in uppercase), while making the device name lowercase,
turn the port type strings array to an array of structure that contains
both the port type name and the device name suffix.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This array is indexed by port type. Make it self-descriptive by using
the port type enum values as indices in the array initializer.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite unusual when some value can not be equal to a defined range
max value. Also most subsystems defines FOO_TYPE_MAX as a maximum valid
value. So turn the WAN_PORT_MAX meaning from the number of supported
port types to the maximum valid port type.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
wwan_hwsim creates and removes simulated control ports on module loading
and unloading. It would be helpful to be able to create/remove devices
and ports at run-time to trigger wwan port (un-)register actions without
module reloading.
Some simulator objects (e.g. ports) do not have the underling device and
it is not possible to fully manage the simulator via sysfs. wwan_hsim
intend for developers, so implement it as a self-contained debugfs based
management interface.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver simulates a set of WWAN device with a set of AT control
ports. It can be used to test WWAN kernel framework as well as user
space tools.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Sit Wei Hong says:
====================
Enable 2.5Gbps speed for stmmac
Intel mGbE supports 2.5Gbps link speed by overclocking the clock rate
by 2.5 times to support 2.5Gbps link speed. In this mode, the serdes/PHY
operates at a serial baud rate of 3.125 Gbps and the PCS data path and
GMII interface of the MAC operate at 312.5 MHz instead of 125 MHz.
This is configured in the BIOS during boot up. The kernel driver is not able
access to modify the clock rate for 1Gbps/2.5G mode on the fly. The way to
determine the current 1G/2.5G mode is by reading a dedicated adhoc
register through mdio bus.
Changes:
v5 -> v6
patch 1/3
- Check if mdio_bus_data is populated to prevent NULL pointer dereferencing
when accesing mdio_bus_data member
v4 -> v5
patch 1/3
- Rebase to latest code changes after Vladimir's code is merged and fix
build warnings
v3 -> v4
patch 1/3
- Rebase to latest code and Initialize 'found' to 0 to avoid build warning
patch 2/3
- Fix indentation issue from v3
v2 -> v3
patch 1/3
-New patch added to restructure the code. enabling reading the dedicated
adhoc register to determine link speed mode.
patch 2/3
-Restructure for 2.5G speed to use 2500BaseX configuration as the
PHY interface.
patch 3/3
-Restructure to read serdes registers to set max_speed and configure to
use 2500BaseX in 2.5G speeds.
v1 -> v2
patch 1/2
-Remove MAC supported link speed masking
patch 2/2
-Add supported link speed masking in the PCS
iperf3 and ping for 2.5Gbps and regression test on 10M/100M/1000Mbps
is done to prevent regresson issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel mGbE supports 2.5Gbps link speed by increasing the clock rate by
2.5 times of the original rate. In this mode, the serdes/PHY operates at a
serial baud rate of 3.125 Gbps and the PCS data path and GMII interface of
the MAC operate at 312.5 MHz instead of 125 MHz.
For Intel mGbE, the overclocking of 2.5 times clock rate to support 2.5G is
only able to be configured in the BIOS during boot time. Kernel driver has
no access to modify the clock rate for 1Gbps/2.5G mode. The way to
determined the current 1G/2.5G mode is by reading a dedicated adhoc
register through mdio bus. In short, after the system boot up, it is either
in 1G mode or 2.5G mode which not able to be changed on the fly.
Compared to 1G mode, the 2.5G mode selects the 2500BASEX as PHY interface and
disables the xpcs_an_inband. This is to cater for some PHYs that only
supports 2500BASEX PHY interface with no autonegotiation.
v2: remove MAC supported link speed masking
v3: Restructure to introduce intel_speed_mode_2500() to read serdes registers
for max speed supported and select the appropritate configuration.
Use max_speed to determine the supported link speed mask.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XPCS IP supports 2500BASEX as PHY interface. It is configured as
autonegotiation disable to cater for PHYs that does not supports 2500BASEX
autonegotiation.
v2: Add supported link speed masking.
v3: Restructure to introduce xpcs_config_2500basex() used to configure the
xpcs for 2.5G speeds. Added 2500BASEX specific information for
configuration.
v4: Fix indentation error
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Hai