When emulating TLB miss / invalid exceptions during CACHE instruction
emulation, be sure to set up the correct PC and host_cp0_badvaddr state
for the kvm_mips_emlulate_tlb*_ld() function to pick up for guest EPC
and BadVAddr.
PC needs to be rewound otherwise the guest EPC will end up pointing at
the next instruction after the faulting CACHE instruction.
host_cp0_badvaddr must be set because guest CACHE instructions trap with
a Coprocessor Unusable exception, which doesn't update the host BadVAddr
as a TLB exception would.
This doesn't tend to get hit when dynamic translation of emulated
instructions is enabled, since only the first execution of each CACHE
instruction actually goes through this code path, with subsequent
executions hitting the SYNCI instruction that it gets replaced with.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a CACHE instruction is emulated by kvm_mips_emulate_cache(), the PC
is first updated to point to the next instruction, and afterwards it
falls through the "dont_update_pc" label, which rewinds the PC back to
its original address.
This works when dynamic translation of emulated instructions is enabled,
since the CACHE instruction is replaced with a SYNCI which works without
trapping, however when dynamic translation is disabled the guest hangs
on CACHE instructions as they always trap and are never stepped over.
Roughly swap the meanings of the "done" and "dont_update_pc" to match
kvm_mips_emulate_CP0(), so that "done" will roll back the PC on failure,
and "dont_update_pc" won't change PC at all (for the sake of exceptions
that have already modified the PC).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When faulting guest addresses are matched against guest segments with
the KVM_GUEST_KSEGX() macro, change the mask to 0xe0000000 so as to
include bit 31.
This is mainly for safety's sake, as it prevents a rogue BadVAddr in the
host kseg2/kseg3 segments (e.g. 0xC*******) after a TLB exception from
matching the guest kseg0 segment (e.g. 0x4*******), triggering an
internal KVM error instead of allowing the corresponding guest kseg0
page to be mapped into the host vmalloc space.
Such a rogue BadVAddr was observed to happen with the host MIPS kernel
running under QEMU with KVM built as a module, due to a not entirely
transparent optimisation in the QEMU TLB handling. This has already been
worked around properly in a previous commit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never
get a TLB refill exception in it when KVM is built as a module.
This was observed to happen with the host MIPS kernel running under
QEMU, due to a not entirely transparent optimisation in the QEMU TLB
handling where TLB entries replaced with TLBWR are copied to a separate
part of the TLB array. Code in those pages continue to be executable,
but those mappings persist only until the next ASID switch, even if they
are marked global.
An ASID switch happens in __kvm_mips_vcpu_run() at exception level after
switching to the guest exception base. Subsequent TLB mapped kernel
instructions just prior to switching to the guest trigger a TLB refill
exception, which enters the guest exception handlers without updating
EPC. This appears as a guest triggered TLB refill on a host kernel
mapped (host KSeg2) address, which is not handled correctly as user
(guest) mode accesses to kernel (host) segments always generate address
error exceptions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MicroMIPS kernels may be expected to run on microMIPS only cores which
don't support the normal MIPS instruction set, so be sure to pass the
-mmicromips flag through to the VDSO cflags.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In microMIPS kernels, handle_signal() sets the isa16 mode bit in the
vdso address so that the sigreturn trampolines (which are offset from
the VDSO) get executed as microMIPS.
However commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
changed the offsets to come from the VDSO image, which already have the
isa16 mode bit set correctly since they're extracted from the VDSO
shared library symbol table.
Drop the isa16 mode bit handling from handle_signal() to fix sigreturn
for cores which support both microMIPS and normal MIPS. This doesn't fix
microMIPS only cores, since the VDSO is still built for normal MIPS, but
thats a separate problem.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/13348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid an aliasing issue causing a build error in VDSO:
In file included from include/linux/srcu.h:34:0,
from include/linux/notifier.h:15,
from ./arch/mips/include/asm/uprobes.h:9,
from include/linux/uprobes.h:61,
from include/linux/mm_types.h:13,
from ./arch/mips/include/asm/vdso.h:14,
from arch/mips/vdso/vdso.h:27,
from arch/mips/vdso/gettimeofday.c:11:
include/linux/workqueue.h: In function 'work_static':
include/linux/workqueue.h:186:2: error: dereferencing type-punned pointer will break strict-aliasing rules [-Werror=strict-aliasing]
return *work_data_bits(work) & WORK_STRUCT_STATIC;
^
cc1: all warnings being treated as errors
make[2]: *** [arch/mips/vdso/gettimeofday.o] Error 1
with a CONFIG_DEBUG_OBJECTS_WORK configuration and GCC 5.2.0. Include
`-fno-strict-aliasing' along with compiler options used, as required for
kernel code, fixing a problem present since the introduction of VDSO
with commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO").
Thanks to Tejun for diagnosing this properly!
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.3+
Patchwork: https://patchwork.linux-mips.org/patch/13357/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow KASLR to be selected on Pistachio based systems. Tested on a
Creator Ci40.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13356/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On certain MIPS32 devices, the ftrace tracer "function_graph" uses
__lshrdi3() during the capturing of trace data. ftrace then attempts to
trace __lshrdi3() which leads to infinite recursion and a stack overflow.
Fix this by marking __lshrdi3() as notrace. Mark the other compiler
intrinsics as notrace in case the compiler decides to use them in the
ftrace path.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: <linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 4.2.x-
Patchwork: https://patchwork.linux-mips.org/patch/13354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Hardware page Table Walker (HTW) is being misconfigured on 64-bit
kernels. The PWSize.PS (pointer size) bit determines whether pointers
within directories are loaded as 32-bit or 64-bit addresses, but was
never being set to 1 for 64-bit kernels where the unsigned long in pgd_t
is 64-bits wide.
This actually reduces rather than improves performance when the HTW is
enabled on P6600 since the HTW is initiated lots, but walks are all
aborted due I think to bad intermediate pointers.
Since we were already taking the width of the PTEs into account by
setting PWSize.PTEW, which is the left shift applied to the page table
index *in addition to* the native pointer size, we also need to reduce
PTEW by 1 when PS=1. This is done by calculating PTEW based on the
relative size of pte_t compared to pgd_t.
Finally in order for the HTW to be used when PS=1, the appropriate
XK/XS/XU bits corresponding to the different 64-bit segments need to be
set in PWCtl. We enable only XU for now to enable walking for XUSeg.
Supporting walking for XKSeg would be a bit more involved so is left for
a future patch. It would either require the use of a per-CPU top level
base directory if supported by the HTW (a bit like pgd_current but with
a second entry pointing at swapper_pg_dir), or the HTW would prepend bit
63 of the address to the global directory index which doesn't really
match how we split user and kernel page directories.
Fixes: cab25bc753 ("MIPS: Extend hardware table walking support to MIPS64")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.
Also print these fields out along with the others in print_htw_config().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify the DSP instruction wrapper macros which use explicit encodings
for microMIPS and normal MIPS by using the new encoding macros and
removing duplication.
To me this makes it easier to read since it is much shorter, but it also
ensures .insn is used, preventing objdump disassembling the microMIPS
code as normal MIPS.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hardcoded MIPS instruction encodings are provided for tlbinvf, mfhc0 &
mthc0 instructions, but microMIPS encodings are missing. I doubt any
microMIPS cores exist at present which support these instructions, but
the microMIPS encodings exist, and microMIPS cores may support them in
the future. Add the missing microMIPS encodings using the new macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the toolchain doesn't support MSA we encode MSA instructions
explicitly in assembly. Unfortunately we use .word for both MIPS and
microMIPS encodings which is wrong, since 32-bit microMIPS instructions
are made up from a pair of halfwords.
- The most significant halfword always comes first, so for little endian
builds the halves will be emitted in the wrong order.
- 32-bit alignment isn't guaranteed, so the assembler may insert a
16-bit nop instruction to pad the instruction stream to a 32-bit
boundary.
Use the new instruction encoding macros to encode microMIPS MSA
instructions correctly.
Fixes: d96cc3d1ec ("MIPS: Add microMIPS MSA support.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <Paul.Burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Toolchains may be used which support microMIPS but not VZ instructions
(i.e. binutis 2.22 & 2.23), so extend the explicitly encoded versions of
the guest COP0 register & guest TLB access macros to support microMIPS
encodings too, using the new macros.
This prevents non-microMIPS instructions being executed in microMIPS
mode during CPU probe on cores supporting VZ (e.g. M5150), which cause
reserved instruction exceptions early during boot.
Fixes: bad50d7925 ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To allow simplification of macros which use inline assembly to
explicitly encode instructions, add a few simple abstractions to
mipsregs.h which expand to specific microMIPS or normal MIPS encodings
depending on what type of kernel is being built:
_ASM_INSN_IF_MIPS(_enc) : Emit a 32bit MIPS instruction if microMIPS is
not enabled.
_ASM_INSN32_IF_MM(_enc) : Emit a 32bit microMIPS instruction if enabled.
_ASM_INSN16_IF_MM(_enc) : Emit a 16bit microMIPS instruction if enabled.
The macros can be used one after another since the MIPS / microMIPS
macros are mutually exclusive, for example:
__asm__ __volatile__(
".set push\n\t"
".set noat\n\t"
"# mfgc0 $1, $%1, %2\n\t"
_ASM_INSN_IF_MIPS(0x40610000 | %1 << 11 | %2)
_ASM_INSN32_IF_MM(0x002004fc | %1 << 16 | %2 << 11)
"move %0, $1\n\t"
".set pop"
: "=r" (__res)
: "i" (source), "i" (sel));
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13310/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As noticed by Sergei in the discussion of Andrea Gelmini's patch series.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
The versions of the __write_{32,64}bit_gc0_register() macros for when
there is no virt support in the assembler use the "J" inline asm
constraint to allow integer zero, but this needs to be accompanied by
the "z" formatting string so that it turns into $0. Fix both macros to
do this.
Fixes: bad50d7925 ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13289/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When starting secondary VPEs which support EVA and the SegCtl registers,
copy the memory segmentation configuration from the running VPE to ensure
that all VPEs in the core have a consistent virtual memory map.
The EVA configuration of secondary cores is dealt with when starting the
core via the CM.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13291/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SegCtl registers are standard for MIPSr3..MIPSr5. Add definitions of
these registers and use them rather than constants
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13290/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 12822570a2 ("MIPS: Separate XPA CPU feature into LPA and MVH")
wasn't fully applied, possibly due to a conflict with commit
f270d881fa ("MIPS: Detect MIPSr6 Virtual Processor support"). This
left decode_config5() referring to the non-existent MIPS_CPU_XPA, which
breaks the build when XPA is enabled:
arch/mips/kernel/cpu-probe.c In function ‘decode_config5’:
arch/mips/kernel/cpu-probe.c:838:17: error: ‘MIPS_CPU_XPA’ undeclared (first use in this function)
c->options |= MIPS_CPU_XPA;
^
Apply the missing hunk, dropping the CONFIG_XPA ifdef and setting the
MIPS_CPU_MVH option when Config5.MVH is set.
Fixes: 12822570a2 ("MIPS: Separate XPA CPU feature into LPA and MVH")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Link: https://patchwork.linux-mips.org/patch/13112/
Patchwork: https://patchwork.linux-mips.org/patch/13277/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When using an external interrupt controller (EIC) the interrupt mask
bits in the cop0 Status register are reused for the Interrupt Priority
Level, and any interrupts with a priority lower than the field will be
ignored. Clear the field to 0 by default such that all interrupts are
serviced.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When using an external interrupt controller (EIC) the interrupt mask
bits in the cop0 Status register are reused for the Interrupt Priority
Level, and any interrupts with a priority lower than the field will be
ignored. Clear the field to 0 by default such that all interrupts are
serviced. Without doing so we default to arbitrarily ignoring all or
some subset of interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Joe Perches <joe@perches.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13272/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull perf updates from Ingo Molnar:
"Mostly tooling and PMU driver fixes, but also a number of late updates
such as the reworking of the call-chain size limiting logic to make
call-graph recording more robust, plus tooling side changes for the
new 'backwards ring-buffer' extension to the perf ring-buffer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
perf record: Read from backward ring buffer
perf record: Rename variable to make code clear
perf record: Prevent reading invalid data in record__mmap_read
perf evlist: Add API to pause/resume
perf trace: Use the ptr->name beautifier as default for "filename" args
perf trace: Use the fd->name beautifier as default for "fd" args
perf report: Add srcline_from/to branch sort keys
perf evsel: Record fd into perf_mmap
perf evsel: Add overwrite attribute and check write_backward
perf tools: Set buildid dir under symfs when --symfs is provided
perf trace: Only auto set call-graph to "dwarf" when syscalls are being traced
perf annotate: Sort list of recognised instructions
perf annotate: Fix identification of ARM blt and bls instructions
perf tools: Fix usage of max_stack sysctl
perf callchain: Stop validating callchains by the max_stack sysctl
perf trace: Fix exit_group() formatting
perf top: Use machine->kptr_restrict_warned
perf trace: Warn when trying to resolve kernel addresses with kptr_restrict=1
perf machine: Do not bail out if not managing to read ref reloc symbol
perf/x86/intel/p4: Trival indentation fix, remove space
...
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
most architectures are relying on mmap_sem for write in their
arch_setup_additional_pages. If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving. Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Andy Lutomirski <luto@amacapital.net> [x86 vdso]
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This option was replaced by PAGE_COUNTER which is selected by MEMCG.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_MIPS32_N32=y but CONFIG_BINFMT_ELF disabled results in the
following linker errors:
arch/mips/built-in.o: In function `elf_core_dump':
binfmt_elfn32.c:(.text+0x23dbc): undefined reference to `elf_core_extra_phdrs'
binfmt_elfn32.c:(.text+0x246e4): undefined reference to `elf_core_extra_data_size'
binfmt_elfn32.c:(.text+0x248d0): undefined reference to `elf_core_write_extra_phdrs'
binfmt_elfn32.c:(.text+0x24ac4): undefined reference to `elf_core_write_extra_data'
CONFIG_MIPS32_O32=y but CONFIG_BINFMT_ELF disabled results in the following
linker errors:
arch/mips/built-in.o: In function `elf_core_dump':
binfmt_elfo32.c:(.text+0x28a04): undefined reference to `elf_core_extra_phdrs'
binfmt_elfo32.c:(.text+0x29330): undefined reference to `elf_core_extra_data_size'
binfmt_elfo32.c:(.text+0x2951c): undefined reference to `elf_core_write_extra_phdrs'
binfmt_elfo32.c:(.text+0x29710): undefined reference to `elf_core_write_extra_data'
This is because binfmt_elfn32 and binfmt_elfo32 are using symbols from
elfcore but for these configurations elfcore will not be built.
Fixed by making elfcore selectable by a separate config symbol which
unlike the current mechanism can also be used from other directories
than kernel/, then having each flavor of ELF that relies on elfcore.o,
select it in Kconfig, including CONFIG_MIPS32_N32 and CONFIG_MIPS32_O32
which fixes this issue.
Link: http://lkml.kernel.org/r/20160520141705.GA1913@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Hogan