Change-Id: Ibd0bcd46895eb88952b9db29e1f68572d39aae01
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The APB DMA block handles DMA transfers to and from some peripherals
in the Tegra SOC. It reads from sequential addresses on the memory
bus, and writes repeatedly to the same address on the APB bus.
Two transfer modes are supported, oneshot for transferring a known
size to or from a peripheral, and continuous for streaming data.
In continuous mode, a callback occurs when the buffer is half full
to allow the existing data to be handled and a new request queued.x
v2 changes:
dma API no longer uses PTR_ERR
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement cpufreq support for the Tegra SOC. DVFS is handled by the
core virtual cpu clock. The frequencies of the two cores are tied
together, the highest frequency requested by either core determines
the actual frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- Add drivers to clock lookup table
- Add new pll_m entries
- Support I2C U16 divider
- Fix rate reporting on 32.768kHz clock
- Call propagate rate only if set_rate succeeds
- Add support for audio_sync clock
- Add 24MHz to PLLA frequency list
- Correct i2s1/2/spdifout mux
- Add suspend support
- Fix enable/disable parent clocks in set_parent
- Add max_rate parameter to all clocks
- DVFS support
- Add virtual cpu clock with dvfs
- Support clk_round_rate
- Fix requesting very high periph frequencies
- Add quirks for PLLU:
PLLU is slightly different from the rest of the PLLs. The
lock enable bit is at bit 22 instead of 18 in the MISC
register, and the post divider field is a single bit with
reversed values from other PLLs.
- Simplify recalculating clock rates
- Fix UART divider flags
- Remove unused clock ops
Signed-off-by: Colin Cross <ccross@android.com>
The Tegra SOC contains fuses to identify the CPU type and
bin, and a unique id. The CPU info is required to determine
the correct voltages for each cpu and core frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- the reset values for some pin groups in the tegra pin mux can result in
functional errors due to conflicting with actively-configured pin groups
muxing from the same controller. this change adds a known safe, non-
conflicting mux for every pin group, which can be used on platforms
where the pin group is not routed to any peripheral
- also add each pin group's I/O voltage rail, to enable platform code to
map from the pin groups used by each interface to the regulators used
for dynamic voltage control
- add routines to individually configure the tristate, pin mux and pull-
ups for a pingroup_config array, so that it is possible to program
individual values at run-time without modifying other values.
this allows driver power-management code to reprogram individual
interfaces into lower power states during idle / suspend, or to
reprogram the pin mux to support multiple physical busses per
internal controller (e.g., sharing a single I2C or SPI controller
across multiple pin groups)
- move chip-specific data like pingroups and drive-pingroups
out of the common code and into chip-specific code
- fix debug output for group with no pullups
- add a TEGRA_MUX_SAFE function. Setting a pingroup to TEGRA_MUX_SAFE
will automatically select a mux setting that is guaranteed not to
conflict with any of the hardware blocks.
Signed-off-by: Gary King <gking@nvidia.com>
mirror IRQ enable and disable operations on the legacy PPI system
interrupt controller, since the legacy controller is responsible
for responding to wakeup interrupts when the CPU is in LP2 idle mode
save the irq controller state on suspend and restore on resume
Signed-off-by: Gary King <gking@nvidia.com>
The "legacy irq controller" duplicates the functionality of the GIC,
but remains powered during the cpu suspend and idle modes that power
down the CPU and the GIC.
Signed-off-by: Colin Cross <ccross@android.com>
Add missing io address map entries from datasheet.
Add the IRAM area to the statically mapped io regions.
Correct the onewire, USB, and statmon addresses
Signed-off-by: Colin Cross <ccross@android.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Since we can get both physical and virtual addresses from the addruart
macro, we can use this to establish the debug mappings.
In the case of CONFIG_DEBUG_ICEDCC, we don't need any mappings, but
may still need to setup r7 correctly.
Incorporating ASM changes from Nicolas Pitre <npitre@fluxnic.net>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
As mentioned in the comment right at the top, the first four fields
are directly accessed by assembly code in head.S. Move nr_irqs so the
comment is true again.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
this patch fix the following errors :
arch/arm/mach-mx3/mach-pcm037_eet.c:62: error: implicit declaration of function 'MXC_SPI_CS'
arch/arm/mach-mx3/mach-pcm037_eet.c:185: error: implicit declaration of function 'imx35_add_spi_imx0'
from the Kconfig pcm037 is i.MX31 based and not i.MX35 so replace
imx35_add_spi_imx0 by imx31_add_spi_imx0
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: remove unneeded #include <mach/spi.h>]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.
Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>
this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>
During the reorganisation of the imx-i2c devices
(in 64de5ec168) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes build error about GPIO address due to
conflict of commit 4d914705 and 19a2c065.
- commit 4d914705: Fix on GPIO base addresses
- commit 19a2c065: Moves initial map for merging S5P64X0
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Mike Rapoport