DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total
when typical 4 byte message is sent. Don't hard-code time limit to
54 ms, but calculate it. Time limit is only used to determine when to
start poll "DiSEqC Tx ready" status from the chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
No need to clear negative msb bits as those were dropped in any
case when data is written to register.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Si2168-B40 firmware API has changed somewhere between 4.0-11 and
4.0-19 so that sleep will lose firmware upgrade from the chip. Due
to that firmware re-upload is needed when newer firmwares are used.
Rewrote firmware handling logic partly at the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those tables are currently unused, so comment them out:
drivers/media/dvb-frontends/dib0090.c:852:18: warning: 'rf_ramp_pwm_sband' defined but not used [-Wunused-const-variable=]
static const u16 rf_ramp_pwm_sband[] = {
^~~~~~~~~~~~~~~~~
drivers/media/dvb-frontends/dib0090.c:800:18: warning: 'bb_ramp_pwm_boost' defined but not used [-Wunused-const-variable=]
static const u16 bb_ramp_pwm_boost[] = {
^~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid this warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1243:18: warning: 'nicam_presc_table_val' defined but not used [-Wunused-const-variable=]
static const u16 nicam_presc_table_val[43] = {
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
status is not initialized so it can contain garbage. The
check for status containing the FE_HAS_LOCK bit may randomly pass
or fail if the read of register 0x8c fails to set status after 25
read attempts. Fix this by initializing status to 0.
Issue found with CoverityScan, CID#986738
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rtl2832 demod has 2 sets of PID filters. This patch enables
the filter support when using a slave demod.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return -EINVAL if ds3000_set_frontend is called with invalid parameters.
v1 of the patch series got incorrect subject lines.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move mn88472 DVB-T/T2/C demod driver out of staging to media.
v2: Fix build error reported by kbuild test robot:
drivers/staging/media/mn88472/Makefile: No such file or directory
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Finalize driver in order to move out of staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Latest, 3rd, regmap instance should be freed on error case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/helene.c: In function 'helene_write_regs':
drivers/media/dvb-frontends/helene.c:312:5: warning: format '%lu' expects argument of type 'long unsigned int', but argument 5 has type 'unsigned int' [-Wformat=]
"wr reg=%04x: len=%d vs %lu is too big!\n",
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
correct is CXD2841ER and CXD2854ER
incorrect was CXD2441ER and CXD2454ER
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
now when new tuning parameters specified demod should retune.
Also ISDB-T frequency offset calculation added
(cxd2841er_get_carrier_offset_i).
While here, fix re-tune for DVB-C Annex A, using the desired
bandwidth, instead of using 8MHz.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Avoid error message:
cxd2841er_read_status_s(): invalid state 1
Always force demod to shutdown state before initializing
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CXD2854ER is identical to CXD2841ER except ISDB-T/S added.
New method 'cxd2841er_attach_i' is added
xtal frequency now configurable. Available options:
20.5MHz, 24MHz, 41MHz
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is Sony HELENE DVB-S/S2 DVB-T/T2 DVB-C/C2 ISDB-T/S tuner
driver (CXD2858ER).
Tuner is used on NetUP Dual Universal DVB CI card (hardware revision 1.4).
Use 'helene_attach_s' to attach tuner in 'satellite mode'.
Use 'helene_attach' for 'terrestrial mode'.
Satellite delivery systems supported:
DVB-S/S2, ISDB-S
Terrestrial delivery systems supported:
DVB-T/T2, ISDB-T
Cable delivery systems supported:
DVB-C/C2
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
The ds3000 driver returned 1 as an error code in many places.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using div_u64() instead of do_div() makes the code slightly more
readable by humans.
[mchehab@osg.samsung.org: originally, this patch was proposed as a bug
fix for a gcc bug. This was solved already, but it is still better to
use div_u64, instead of do_div, so I'm applying it, removing the
comments about the gcc bug]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the regmap overrides
that makes the i2c accesses unlocked and use plain old regmap
accesses. This also removes the need for the regmap wrappers used by
rtl2832_sdr, so deconvolute the code further and provide the regmap
handle directly instead of the wrapper functions.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the code that makes the
i2c accesses unlocked. But add a mutex so that firmware commands are
still serialized.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix this smatch error:
dib0090.c:1124 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
s32tmp in the below code may be negative, and dev->mclk_khz is an
unsigned type.
s32tmp = 0x10000 * (tuner_frequency - c->frequency);
s32tmp = DIV_ROUND_CLOSEST(s32tmp, dev->mclk_khz);
This is undefined, as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is of unsigned type.
So, change mclk_khz to be signed (s32).
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change get_frontend to re-check current lock status rather than relying
on a cached value from get_status. Removes potential for tuning failure
if get_frontend is called during tuning.
Probably not too essential as other changes work around this:
https://patchwork.linuxtv.org/patch/32845/
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do statistics polling on read status in order to avoid
unnecessary delayed work.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback parameter to select enable / disable slave TS and use
it when slave demod is in use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Finalize the driver.
It still lacks a lot of features, like all statistics and PLP
filtering, but basic functionality and sensitivity is pretty good
shape.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we want au0828 to use the core function to create the MC
graphs, use enum demod_pad_index instead of
enum au8522_media_pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch with -pkernel --no-data keeps complaining about rf_ramp:
drivers/media/dvb-frontends/dib0090.c:1119 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While there's no risk of divison by zero, the logic there is akward, as it
does the calculus for the numerator and denominator before checking
if this will be used.
Change the order to check first if the denominator is zero, and only
calculating the numerator/denominator if not.
This should also avoid those smatch errors:
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new pad for ALSA Audio Out to au8522_media_pads.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the au8522_media_pads enum to au8522.h from au8522_priv.h to export
them. This will allow au0828-core to use these defines instead of
hard-coding them them.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both dib9000_read16_attr and dib9000_write16_attr can return an
error code. However, they currently return an u16. This produces the
following warnings on smatch:
drivers/media/dvb-frontends/dib9000.c:262 dib9000_read16_attr() warn: signedness bug returning '(-121)'
drivers/media/dvb-frontends/dib9000.c:321 dib9000_write16_attr() warn: signedness bug returning '(-22)'
drivers/media/dvb-frontends/dib9000.c:353 dib9000_write16_attr() warn: signedness bug returning '(-121)'
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/dvb-frontends/dib0090.c:1118 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
Instead of using the DTV properties cache directly, pass the get
frontend data as an argument. For now, everything should remain
the same, but the next patch will prevent get_frontend to
affect the global cache.
This is needed because several drivers don't care enough to only
change the properties if locked. Due to that, calling
G_PROPERTY before locking on those drivers will make them to
never lock. Ok, those drivers are crap and should never be
merged like that, but the core should not rely that the drivers
would be doing the right thing.
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This device doesn't really have a get_frontend(). All it does is
to blindly set everything to auto mode.
Remove the get_frontend(), as the code does that already,
and put the frontend changes at set_frontend, where it
belongs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.
This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.
Tested with a saa7134 card 78:
ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from ktime_get_real is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
[mchehab@osg.samsung.com: fix trivial merge conflicts]
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(dev->stat_work). A similar bug in si2157 caused
kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rtl2830_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(&dev->stat_work). A similar bug in si2157
caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
af9033_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(&dev->stat_work). A similar bug in si2157
caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
af9013_remove was calling kfree(state) with possibly still active
schedule_delayed_work(&state->statistics_work). A similar bug in
si2157 caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stv6110x_devctl structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
1. Let us return directly if a call of the si2165_readreg8()
function failed.
2. Reduce the scope for the local variables "ret" and "tmp" to one branch
of an if statement.
3. Delete the jump label "err" then.
4. Return the value from a call of the si2165_writereg8() function
without using an extra assignment for the variable "ret" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The si2165 does not support bandwidth auto-detection.
Reject the request.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for analog and dvb tv using media controller.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not remove slave TS NULL padding PID (0x1fff) by default as
there is no real need. After that whole TS is passed to kernel sw
PID filter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to debug possible I2C failures without knowing the
possible register itself. Add register number to error printing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kmemleak:
unreferenced object 0xffff880321e1da40 (size 32):
comm "modprobe", pid 3309, jiffies 4295019569 (age 2359.636s)
hex dump (first 32 bytes):
47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G...............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff82278c8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8153c08c>] kmem_cache_alloc_trace+0x1ec/0x280
[<ffffffffa13a896a>] au8522_probe+0x19a/0xa30 [au8522_decoder]
[<ffffffff81de0032>] i2c_device_probe+0x2b2/0x490
[<ffffffff81ca7004>] driver_probe_device+0x454/0xd90
[<ffffffff81ca7c1b>] __device_attach_driver+0x17b/0x230
[<ffffffff81ca15da>] bus_for_each_drv+0x11a/0x1b0
[<ffffffff81ca6a4d>] __device_attach+0x1cd/0x2c0
[<ffffffff81ca7d43>] device_initial_probe+0x13/0x20
[<ffffffff81ca451f>] bus_probe_device+0x1af/0x250
[<ffffffff81c9e0f3>] device_add+0x943/0x13b0
[<ffffffff81c9eb7a>] device_register+0x1a/0x20
[<ffffffff81de8626>] i2c_new_device+0x5d6/0x8f0
[<ffffffffa0d88ea4>] v4l2_i2c_new_subdev_board+0x1e4/0x250 [v4l2_common]
[<ffffffffa0d88fe7>] v4l2_i2c_new_subdev+0xd7/0x110 [v4l2_common]
[<ffffffffa13b2f76>] au0828_card_analog_fe_setup+0x2e6/0x3f0 [au0828]
Checking where the error happens:
(gdb) list *au8522_probe+0x19a
0x99a is in au8522_probe (drivers/media/dvb-frontends/au8522_decoder.c:761).
756 printk(KERN_INFO "au8522_decoder attach existing instance.\n");
757 break;
758 }
759
760 demod_config = kzalloc(sizeof(struct au8522_config), GFP_KERNEL);
761 if (demod_config == NULL) {
762 if (instance == 1)
763 kfree(state);
764 return -ENOMEM;
765 }
Shows that the error path is not being handled properly.
The are actually several issues here:
1) config free should have been calling hybrid_tuner_release_state()
function, by calling au8522_release_state();
2) config is only allocated at the digital part. On the analog one,
it is received from the caller.
A complex logic could be added to address it, however, it is simpler
to just embeed config inside the state.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ops aren't used by any driver, with is weird. I suspect
that mantis_vb3030 driver were not working properly...
Anyway, now that the driver uses the set_parms, the DVB
frontend core should do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two callbacks are the ones that should be used by normal
DVB frontend drivers.
Add support for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari