There are two different PCIe PHYs on SM8450, one having one lane (v5)
and another with two lanes (v5.20). This commit adds support for the
second PCIe phy.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211218141754.503661-3-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two different PCIe PHYs on SM8450, one having one lane (v5)
and another with two lanes (v5.20). This commit adds support for the
first PCIe phy only, support for the second PCIe PHY is coming in next
commits.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211214225846.2043361-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Many recent Qualcomm platforms comes with native DP and eDP support.
This consists of a controller in the MDSS and a QMP-like PHY.
While similar to the well known QMP block, the eDP PHY only has TX lanes
and the programming sequences are slightly different. Rather than
continuing the trend of parameterize the QMP driver to pieces, this
introduces the support as a new driver.
The registration of link and pixel clocks are borrowed from the QMP
driver. The non-DP link frequencies are omitted for now.
The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
the prior is supported for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211103234410.1352424-2-bjorn.andersson@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the tables and constants for init sequences for UFS QMP phy found in
SM4250/6115 SoC. The phy is a variation of the v2 phy, but is mistakenly
labeled as v3-660 in downstream sources.
QSERDES COM, RX, TX registers match fully existing v2 registers, with
a few additions. PCS registers don't have much in common, but there are
no clashes with existing ones so new registers were added to existing v2
PCS pack.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Link: https://lore.kernel.org/r/20210821155657.893165-3-iskren.chernev@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe PHY version used in SDX55 is v4.20 which has different register
offsets compared to the v4.0x PHYs. So separate register defines are
used for init sequence and PHY status.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210427065400.18958-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the registers for UFS found in SM8350. The UFS phy used in SM8350
seems to have same offsets as V5 phy, although Documentation for that is
lacking.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210204165805.62235-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB DP & UNI PHYs found on SM8350. These use
version 5.0.0 of the QMP PHY IP and thus require new "V5"
definitions of the register offset macros for the QSERDES RX
and TX blocks. The QSERDES common and QPHY PCS blocks' register
offsets are largely unchanged from V4 so some of the existing
macros can be reused.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210115174723.7424-3-jackp@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SM8250 has multiple different PHY versions:
QMP GEN3x1 PHY - 1 lane
QMP GEN3x2 PHY - 2 lanes
QMP Modem PHY - 2 lanes
Add support for these with relevant init sequence. In order to abstract
the init sequence, this commit introduces secondary tables which can
be used to factor out the unique sequence for each PHY while the former
tables can have the common sequence.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20201027170033.8475-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB3 + DisplayPort (DP) "combo" phy to the qmp phy
driver. We already have support for the USB3 part of the combo phy, so
most additions are for the DP phy.
Split up the qcom_qmp_phy{enable,disable}() functions into the phy init,
power on, power off, and exit functions that the common phy framework
expects so that the DP phy can add even more phy ops like
phy_calibrate() and phy_configure(). This allows us to initialize the DP
PHY and configure the AUX channel before powering on the PHY at the link
rate that was negotiated during link training.
The general design is as follows:
1) DP controller calls phy_init() to initialize the PHY and configure
the dp_com register region.
2) DP controller calls phy_configure() to tune the link rate and
voltage swing and pre-emphasis settings.
3) DP controller calls phy_power_on() to enable the PLL and power on
the phy.
4) DP controller calls phy_configure() again to tune the voltage swing
and pre-emphasis settings determind during link training.
5) DP controller calls phy_calibrate() some number of times to change
the aux settings if the aux channel times out during link training.
6) DP controller calls phy_power_off() if the link rate is to be
changed and goes back to step 2 to try again at a different link rate.
5) DP controller calls phy_power_off() and then phy_exit() to power
down the PHY when it is done.
The DP PHY contains a PLL that is different from the one used for the
USB3 PHY. Instead of a pipe clk there is a link clk and a pixel clk
output from the DP PLL after going through various dividers. Introduce
clk ops for these two clks that just tell the child clks what the
frequency of the pixel and link are. When the phy link rate is
configured we call clk_set_rate() to update the child clks in the
display clk controller on what rate is in use. The clk frequencies
always differ based on the link rate (i.e. 1.6Gb/s 2.7Gb/s, 5.4Gb/s, or
8.1Gb/s corresponding to various transmission modes like HBR1, HBR2 or
HBR3) so we simply store the link rate and use that to calculate the clk
frequencies.
The PLL enable sequence is a little different from other QMP phy PLLs so
we power on the PLL in qcom_qmp_phy_configure_dp_phy() that gets called
from phy_power_on(). This should probably be split out better so that
each phy has a way to run the final PLL/PHY enable sequence.
This code is based on a submission of this phy and PLL in the drm
subsystem.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Vara Reddy <varar@codeaurora.org>
Cc: Tanmay Shah <tanmay@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20200609034623.10844-1-tanmay@codeaurora.org
Link: https://lore.kernel.org/r/20200916231202.3637932-8-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There were some problem in ipq8074 Gen2 PCIe phy init sequence.
1. Few register values were wrongly updated in the phy init sequence.
2. The register QSERDES_RX_SIGDET_CNTRL is a RX tuning parameter
register which is added in serdes table causing the wrong register
was getting updated.
3. Clocks and resets were not added in the phy init.
Fix these to make Gen2 PCIe port on ipq8074 devices to work.
Fixes: eef243d04b ("phy: qcom-qmp: Add support for IPQ8074")
Cc: stable@vger.kernel.org
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1596036607-11877-4-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add both the DP and UNI PHY for primary/secondary usb controllers.
The tables are very similar to sm8150 (serdes_tbl is identical), but there
are some differences.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200524021416.17049-4-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the USB3 PHY used by the secondary usb controller on sm8150
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200524021416.17049-3-jonathan@marek.ca
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The UFS QMP v4 PHY has a largely different register set versus USB and
PCIe. Rename the register offsets to denote that the value is specific for
the UFS PCS register.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1588636467-23409-6-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for SM8150 QMP USB3 PHY with the necessary
initialization sequences as well as additional QMP V4
register definitions.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/1588636467-23409-4-git-send-email-wcheng@codeaurora.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to PHY drivers for Qualcomm platforms.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register
defines and support for SM8150 QMP UFS PHY.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MSM8998 contains a single QMP v3 USB3 phy similar to the existing sdm845
support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add UFS PHY support to make SDM845 UFS work with common PHY framework.
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
QMP V3 UNI PHY is a single lane USB3 PHY without support
for DisplayPort (DP).
Main difference from DP combo QMPv3 PHY is that UNI PHY
doesn't have dual RX/TX lanes and no separate DP_COM
block for configuration related to type-c or DP.
Also remove "qcom,qmp-v3-usb3-phy" compatible string which
was earlier added for sdm845 only as there wouldn't be
any user of same.
While at it, fix has_pwrdn_delay attribute for USB-DP
PHY configuration and.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Disable clocks and enable PHY autonomous mode to detect
wakeup events when PHY is suspended.
Core driver should notify speed to PHY driver to enable
LFPS and/or RX_DET interrupts.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Registers offsets for QMP V3 PHY are changed from
previous versions (1/2), update same in header file.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
New revision (v3) of QMP PHY uses different offsets
for almost all of the registers. Hence, move these
definitions to header file so that updated offsets
can be added for QMP v3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Dmitry Baryshkov