The standard badness values don't seem to fit to all preferences.
Some configuration prefer the side output over the headphone, some
want the speaker over the surround, etc.
This patch moves the badness table pointers into hda_gen_spec, so that
the codec driver can override them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling snd_hda_attach_beep_device() and
snd_hda_detach_beep_device() in each codec driver, move them to the
generic parser. The codec driver just needs to set spec->beep_nid for
activating the digital beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the headphone mic jack enum control is created (via explicitly
specification by user), it doesn't make much sense to change the I/O
direction dynamically per capture source change, since the I/O
direction is rather controlled over the enum ctl.
This also reduces the implicit dependency between the capture source
and the hp mic jack enum ctls, which might confuse a program accessing
the whole control elements at once like alsactl.
In addition, this patch introduces update_hp_automute_hook() function
to call the proper hook function. It's just to remove the open codes
in multiple places in hda_generic.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no big merit to distinguish these two hints. Instead, just
have a single flag, add_jack_modes, for creating the jack mode enum
ctls for both I/O directions.
The hint string parser code is left and translated as add_jack_modes
just for keeping compatibility.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch improves the generic parser code to allow to set up the
headphone jack as a mic input. User can enable this feature by giving
hp_mic hint string.
The former shared hp/mic feature for the single built-in mic is still
retained. This detection can be disabled now via hp_mic_detect hint
string, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loopback list is referred by the VIA codec driver no matter
whether CONFIG_PM is set or not, thus we need to enable it always.
Otherwise it gets compile errors.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a better power filter hook for powering down unused
widgets in the generic parser.
The feature is enabled by setting hda_gen_spec.power_down_unused
flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1988 family and AD1882 codecs have another mixer widget (0x21)
between the analog-loopback mixer widget (0x20) and the actual
outputs. Due to this hole, the analog-loopbacks aren't sent properly
to the output pins.
As a band-aid fix, introduce another fields holding the aamix merge
path, and activate it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It'd be better to give another name to the secondary (alt) analog PCM
stream, which is dedicated for the independent HP out and extra
inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch eventually fixes two issues:
- Handle the case where the primary output is a headphone and can have
independent HP mode;
so far we checked only the case where the headphone is the secondary
output.
- Fix the conflict of HP independent mode and aamix mode;
when switched to aamix mode, the DAC might be also switched to
another widget shared with other outputs. Then even if we disable
the DAC for the original output, it doesn't change -- because the
active route is from another (shared) DAC to HP pin through aamix.
So, in such a case, we have to prohibit the switch to aamix for HP
routes.
This fixes issues appearing on VT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Looking through the whole definitions, some fields have inappropriate
array sizes, especially about the capture. The array assigned to each
input (pin) should have HDA_MAX_NUM_INPUTS entries while the array
assigned to each ADC should have AUTO_CFG_MAX_INS entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I found a codec configuration which had six inputs, so the max of
five was not appropriate.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play
very similar roles. The only differences are that the former is
called more often (e.g. at init or switching capsrc) while the latter
can take an on/off argument.
As a more generic implementation, consolidate these two hooks, and
pass snd_ctl_elem_value pointer as the second argument. If the
secondary argument is non-NULL, it can take the on/off value, so the
caller handles it like the former capture_switch_hook. If it's NULL,
it's called in the init or capsrc switch case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code. This is redundant
and makes harder to maintain. Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.
This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config(). This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.
Note that ground and 100% vrefs are excluded from the list for
simplicity, currently. We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag. It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new hook which is called at each PCM playback ops.
It can be used to control the codec-specific power-saving feature in
each codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bind-volume workaround was introduced for simplifying the mixer
abstraction in the case where one or more pins of multiple outputs
lack of individual volume controls. This was essentially the case
like Acer Aspire 5935, which has 5.1 speakers and 5.1 (multi-io)
jacks although there are 5 DACs, so some of them must share a DAC.
However, the recent code rewrite changed the DAC assignment policy to
share with the same channel instead of binding to the front, thus
binding the volumes for all channels makes little sense now, rather
it's confusing. So in this patch, the ugly workaround is finally
dropped and simply create the volume control corresponding to the
parsed path position.
For dual headphones or 2.1 speakers with a shared volume control, it's
anyway bound to the same DAC if needed, so this change shouldn't bring
any practical difference.
And, as a good bonus, we can cut off the whole code handling the bind
volume elements.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For codecs that have individual routes going through a loopback mixer
(like VIA codecs), we need to provide an explicit switch to choose
whether the output goes through mixer or directly from DAC.
This patch adds the check for such paths and creates "Loopback Mixing"
enum control when available.
It won't influence on codecs like Realtek or others where the loopback
mixer is connected independently from the primary output routes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call the path activation for the digital input pin properly, not only
setting the pin control. Also add spec->digin_path for keeping the
path index.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of search for the path with the certain route at each time,
keep the path index for each output and loopback, and just use it when
referred.
In this implementation, the path index number begins with one, not
zero (although I've been writing in C over decades). It's just to
make the check for uninitialized values easier.
So far, the input paths aren't handled with indices yet, but still
picked up via snd_hda_get_nid_path() at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the requested path has been already added, return the existing path
instance instead of adding a duplicated instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the implementation in patch_analog.c and patch_via.c,
the generic parser can provide the independent HP PCM stream now.
It's enabled when spec->indep_hp is set by the caller while parsing.
Currently no dynamic PCM switching as in patch_via.c is implemented
yet. The control returns -EBUSY when the value is changed during PCM
operations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's never used in the generic parser. It was there from the old
Realtek code, which has been dropped quite ago, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a flag to indicate whether the vmaster mute hook enum is exposed
or not. Conexant codecs may want not to expose the control depending
on the model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old codecs like AD1986A tend to have long paths as they were just made
to be the way like AC97. The current max depth 5 can be too short for
such devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These handlers are supposed to be called externally from the codec
drivers once when they need to handle own jack events.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, we want to manipulate the auto_pin_cfg table before
passing to snd_hda_gen_parse_auto_config() (e.g. Realtek SSID check
code fiddles with the headphone pin). Also passing ignore_pins just
for snd_hda_parse_pin_defcfg() isn't good.
In this patch, snd_hda_gen_parse_auto_config() is changed to receive
the auto_pin_cfg table to be parsed. The passed auto_pin_cfg table
must have been initialized (typically by calling
snd_hda_gen_parse_auto_config()) beforehand by the caller.
Also together with this change, spec->parse_flags is also removed.
Since this was referred only at the place calling
snd_hda_parse_pin_defcfg(), no longer needed to be kept in spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally the whole generic parser code in Realtek driver is moved into
hda_generic.c so that it can be used for generic codec driver.
The old dumb generic driver is replaced. Yay.
The future plan is to adapt this generic parser for other codecs,
i.e. the codec driver calls the exported functions in generic driver
but adds some codec-specific fixes and setups.
As of this commit, the complete driver code is still duplicated in
Realtek codec driver. The big code reduction will come from now on.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai