The firmware crash dumps on the 6004 are the same as the 6003. Remove the
statement guarding it from dumping on the 6004. Renamed the
REG_DUMP_COUNT_AR6003 to reflect support on both chips.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a tracing point for hif irq and dump the register content to user space.
This is in hif.c as we could use the same code also with SPI but, as ath6kl
doesn't SPI and most likely never will be, this is used just by SDIO so
name the trace point as ath6kl_sdio_irq to make it easier to manage filters.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just use WARN_ON rather than an if containing only WARN_ON(1).
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These checks are no longer needed as the necessary
USB support is already present in the driver.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-initialize the target when fw crash is reported.
This would make the device functional again after
target crash. During the target re-initialization
it is made sure that target is not bugged with data/cmd
request, ar->state ATH6KL_STATE_RECOVERY is used
for this purpose.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the issues which checkpatch found and were easy to fix. Especially
callers of ath6kl_bmi_write() are tricky and that needs to be fixed
separately.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Collect residue firmware logs following firmware assert.
Firmware sends logs to host once the 1500 byte log buffer
has been filled. At time of assert, there could be residue
logs lying in the firmware. This patch pulls those residue
logs. This would give the full picture of the firmware.
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The firmware crash dump printout was wrong as it was using incorrect
offsets.
kvalo: improve commit log, change the "%d:" to print word indexes, not bytes
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update license header with the copyright to Qualcomm Atheros, Inc.
for the year 2011-2012.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John Linville had to revert the part of USB support which was already
in ath6kl due to build problems in commit cb00ec382b ("ath6kl: revert
USB support"). Now that I fixed the build problems properly by adding
ath6kl_core.ko kernel module it's possible to add back the
(incomplete) USB support. This patch is a revert of John's patch and
adds back the USB code which as already in ath6kl, only difference
being minor changes in Makefile and adapting usb.c to new core
function names.
Note that USB support in ath6kl is not complete yet. This code only
makes it possible to boot firmware but as HTC layer does not yet
support USB it's not possible to send any WMI commands nor data
packets to the firmware. That will be added soon.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now ath6kl is ready for splitting core code to ath6kl_core.ko module.
This also makes it possible to link both sdio and usb code to kernel
at the same time, which earlier failed miserably.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We don't need it as debug calls already have a log level and compiler
should be smart enough to optimise away the code when ath6kl debug code
is not enabled. Also it makes it easier to abstract core code to
ath6kl_core.ko.
In ath6kl_dump_registers() I had to change the debug level from ANY to IRQ
as I removed the AR_DBG_LVL_CHECK() check before calling the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl driver is causing build failures when the ath6kl bits are
not built as modules. A better fix is forthcoming in a future release,
but for now lets revert the problematic code.
This reverts the following commits:
fde57764efd70385a26a59d954dda4
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As HTC layer doesn't support USB devices return an error if that happens.
USB support will be added to HTC in the future, this is just a temporary
solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently firmware crash dump is printed only if debug is enabled.
Change it so that the crash dump is always printed.
Also move the code from init.c to hif.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible to busyloop forever in ath6kl_hif_intr_bh_handler(). Add
a check that it lasts only one second.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That way we htc level debug messages can be removed from hif files. Also
add few new messages and remove useless debug message about using
synchrous irq processing (we don't support anything else).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Dan Kephart