Modules: USB generic driver
This is my naive attempt at adding ALSA device support. The attached
patch provides support for the EDIROL UM-3ex. This is a 3-port USB midi
interface with a built-in USB hub and the ability to chain 2 other
UM-3x's in a master-slave configuration. I only have one, so I do not
know how this works in practice.
Though this is a 3-port device, I had to throw in that 4th 'Control' interface
to the definition in order to make the 3rd port work. If I set in/out_cables
to 0x000b, a 3rd interface appears on the driver, but it does nothing.
Changing it to 0x000f allows the 3rd interface to work, but of course
interface 4 does not work because it does not exist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
On the Audigy 2 ZS, disable all sample rate that are not a multiple of
48 kHz because the others work only with the digital output which is
not yet supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Some widespread USB interface chips with adaptive iso endpoints hang
after receiving a series of empty packets when they expect data (ALSA
bug#1585). To avoid this, we have to send packets containing silence
(zero samples) instead.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Somebody at Edirol fucked up and released a new revision of the UA-20
without class-specific descriptors, so now we have to hard-code the
sample format.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Something noticed when studying use of VM_RESERVED in different drivers:
snd_usX2Y_hwdep_pcm_vm_nopage omitted to get_page: fixed.
And how did this work before? Aargh! That nopage is returning a page from
within a buffer allocated by snd_malloc_pages, which allocates a high-order
page, then does SetPageReserved on each 0-order page within.
That would have worked in 2.6.14, because when the area was unmapped,
PageReserved inhibited put_page. 2.6.15-rc1 removed that inhibition (while
leaving ineffective PageReserveds around for now), but it hasn't caused
trouble because.. we've not been freeing from VM_RESERVED at all.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modules: USB generic driver
If we submit all our URBs when a playback stream is started, the first
hwptr_done update for each URB happens at the same time. This results
in an underrun when there isn't enough PCM data available at this
point for all URBs.
To avoid this, we begin submitting our URBs earlier (when the stream
is prepared), with empy packets. When the stream is started, the
prepare_playback_urb() call for each URB will be run only when the
respective URB has completed previously, so the first hwptr_done
updates will be done nicely staggered.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Remove the usb_reset_configuration() call from the probe callback
because it isn't needed and it may interfere with other drivers
already loaded for the device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
Move the usb_complete_callback() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Move the usb_pipe_needs_resubmit() compatibility wrapper out of the
kernel tree.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add more comments about other device modes and unsupported devices to
the Roland part of the quirks table.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: USB generic driver
Simplify the handling of MIDI quirks by treating an interface without
quirks as a QUIRK_MIDI_STANDARD_INTERFACE.
This also fixes the bug where a MIDI_STANDARD quirk would not be
recognized.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a quirk entry for the external MIDI ports of the
Windows Edition of the Hercules DJ Console.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a mixer quirk entry for the Hercules DJ Console (Windows Edition)
that uses a different USB product ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Increase the maximum PCM buffer size to 1 MB. The USB driver doesn't
have any inherent buffer size limit, and big multichannel interfaces
may benefit from this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
There is another revision of the PHASE26 with a different product ID;
add a quirk entry for that, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a quirk entry for the Roland RD-700SX.
This should work for the RD-300SX, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a quirk entry for the Hercules DJ Console to ignore timeouts on
some mixer control transfers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add the SNDRV_PCM_INFO_BATCH flag to the PCM hardware information to
indicate that the driver uses double buffering.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB generic driver
When a USB error occurs that might indicate that the device has been
unplugged, don't resubmit the URB immediately to prevent flooding the
log with error messages before khubd has us disconnect()ed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Emagic devices pad their packets not with 0xff bytes but with a 0xff
byte followed by garbage, so we have to stop at the first such byte.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
With the double buffering, we no longer need contiguous memory for the
PCM buffer, so we can use vmalloc() instead of the preallocation
functions, and increase the maximum size to 256 KB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Use the USB buffer allocation functions to avoid repeated DMA mappings
of our buffers, which are re-used quite a lot.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Take the substream lock when reading hwptr_done to avoid a race
condition with the updates in the URB callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Change prepare_playback_urb() not to stop preparing packets before a
frame boundary has been reached.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
We always had to use double buffering when capturing, and when playback
data for one URB crosses a buffer boundary. The latter would make hwptr
updates less precise because the double-buffered data is read from the
buffer much earlier than the other data is read by the host controller.
Double-buffering all data allows to update hwptr immediately after the
data was copied to the USB buffer(s), which has the additional benefit
of avoiding the latency imposed by the host controller's delay of up to
one frame when interrupting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When preparing capture URBs, we don't need to stop when we cross a
period boundary because we now never handle more than one millisecond of
data per URB anyway.
When handling captured data, use an extra flag to call
snd_pcm_period_elapsed() no more than once. This allows us to move the
period boundary checking code before the copying of the data which
avoids a second locking of the substream's lock.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The EHCI driver doesn't interrupt more than once per millisecond, and
organizes all iso transfers with frame-sized ITDs, so we can (try to)
be more efficient by aligning all URBs on frame boundaries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The nrpacks module parameter is used only when initializing a playback
stream, so it doesn't hurt to make it writeable.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When determining how many packets are needed for one period, we cannot
assume that all packets have their maximum size -- we always use the
nominal sample rate when sending data, and could use an even lower rate
when the endpoint uses frequency feedback.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When capturing audio data, we do not know beforehand how many samples
the device sends per frame, so we have to use URBs that are as short as
possible to make sure that we can handle period boundaries without any
additional latencies.
Furthermore, the total count of URBs submitted doesn't matter when
capturing, so we can just use the maximum number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
PCM Midlevel,ALSA<-OSS emulation,USB USX2Y
This patch removes open_flag from struct _snd_pcm_substream.
All of its uses are substituted by querying struct _snd_pcm_substream's
member ffile instead.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
Make the quirk type an enum instead of a #defined integer, and use a
table for the quirk constructor functions instead of a big switch
statement.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add support for Miditech Midistart and MidiStudio keyboards (another
case of devices using the standard protocol but having no descriptors).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver,USB USX2Y
Description: Fix-up sleeping in sound/usb. Replace big_mdelay() with
msleep() to guarantee the task delays as expected. This also involved
replacing/removing custom sleep functions.
Patch is compile-tested.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
USB generic driver
MOTU builds other USB MIDI interfaces with the same product ID as the
FastLane, so we have to check the bDeviceSubClass field to differentiate
between them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Rename the protocol used by the MOTU FastLane to 'raw' because it might
be useful with other devices, and there are other MOTU interfaces that
do not use this protocol.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
This patch enables the boot commands to activate high speed mode (and
associated sample formats like 8 channels with 24 bits at 96 kHz) on the
SB Audigy 2 NX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
On the SB Audigy 2 NX, capturing with sample rates that are not a
multiple of 48 kHz does not seem to work, so disable it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add support for endpoints with bInterval > 1, and decoding of the
wMaxPacketSize field of high-speed endpoints.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Timer Midlevel,ALSA sequencer,ALSA<-OSS sequencer,Digigram VX core
I2C tea6330t,GUS Library,VIA82xx driver,VIA82xx-modem driver
CA0106 driver,CS46xx driver,EMU10K1/EMU10K2 driver,YMFPCI driver
Digigram VX Pocket driver,Common EMU synth,USB generic driver,USB USX2Y
Checking a pointer for NULL before calling kfree() on it is redundant,
kfree() deals with NULL pointers just fine.
This patch removes such checks from sound/
This patch also makes another, but closely related, change.
It avoids casting pointers about to be kfree()'ed.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
When a device does not provide the bRefresh field in its audio endpoint
descriptors, use the bInterval field instead.
Furthermore, increase the number of sync URBs for better queueing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Many Roland USB MIDI devices have two interfaces that are currently not
used by the driver; claim them anyway.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When a USB packet boundary falls exactly on a buffer boundary, hwptr
remains at the end of the buffer which causes an overflow in the next
iteration and triggers double buffering although the next packet would
actually be contiguous.
This patch ensures that hwptr is always smaller than buffer_size.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Check that the synchronization feedback frequency values returned by the
device are more or less near the nominal frequency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Bind the device files to the (first) audio control interface instead of
the entire USB device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
This patch adds a proc file for the SB Audigy 2 NX which shows the
connection status of the various jacks. Unfortunately, no SPDIF input
frequency (yet).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The ioctls for LIRC compatibility can be removed because the
infrastructure and detection stuff is better done in user space.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The SB Audigy 2 NX needs a special boot-up command before it works in
high speed mode.
However, we don't actually enable it yet because high speed
synchronization doesn't seem to work with this device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The SB Audigy 2 NX does not advertise the sample rate attribute in its
endpoint descriptors although it supports it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Adds mixer controls for the CMSS/Dolby Digital/Power LEDs
on the SB Audigy 2 NX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add ioctls to the Sound Blaster remote control hwdep device so that it
can be used with LIRC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Do not use more than one packet in synchronization feedback URBs because
it would be pointless to send or receive more than one value at the same
time.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add sanity checks when reading the bRefresh value, and actually use it
for the synchronization packets instead of polling at 1000 Hz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Extension units can have type 0, so do not ignore them when constructing
mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Cache the decoded values of idVendor/idProduct to get rid of most of
those ugly le16_to_cpu() calls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ALSA Core,USB generic driver
Add an hwdep interface that supports reading remote control data from
Sound Blaster Extigy and Audigy 2 NX devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add support for the optional status interrupt endpoint in audio control
interfaces, and translate USB status notifications into ALSA mixer
control notifications.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Move all data related to audio control interfaces into a separate struct
local to usbmixer.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Unit/terminal IDs are 8-bit integers, so the unitbitmap
variable does not need to be bigger than 256 bits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
On the SB Audigy 2 NX, frequency feedback doesn't quite work
when playing at 44.1 kHz, so temporarily disable this frequency.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver,USB USX2Y
This patch removes the superfluous driver parameter from the
disconnect functions.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a mechanism to specify source names of selector units,
and add such names for the SB Audigy 2 NX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
In the streamX proc file, show the exact number of samples per
USB frame as 16.16 hexadecimal floating point value.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Add a mixer control map for the SB Audigy 2 NX so
that we get meaningful mixer control names.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver,USB USX2Y
Without this patch, some usb kobjects, which are parents to
the usx2y's kobjects can be freed before the usx2y's.
This led to an oops in get_kobj_path_length() and a dead
keyboard, when the usx2y's kobjects were freed.
The patch ensures the correct sequence.
Tested ok on kernel 2.6.12-rc2.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
This patch adds quirks to support 24-bit PCM I/O in the 'Advanced
Driver' mode of the BOSS GS-10.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
This patch reintroduces the check for endpoint numbers that are
specified explicitly in the quirk structure.
This check was accidentally dropped in the last rewrite of
snd_usbmidi_detect_endpoints().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Clemens Ladisch