This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed a function declaration, removed a variable, renamed a variable
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in the Rx path of the driver it would be better to use ATH_DBG_ANY
rather than ATH_DBG_XMIT for printing debug messages
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9340 is not listed in ath_mac_bb_names, which leads to such a message:
ieee80211 phy0: Atheros AR???? Rev:0 mem=0xb8100000, irq=2
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 172805ad46
overwirtes additional clock settings of AR9330 to
all AR9300 chips.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been tested in STA and AP mode by Florian.
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the do_div macro for 64-bit division. Otherwise, the module will
reference __udivdi3 under 32-bit kernels, which is not allowed in
kernel space.
drivers/built-in.o: In function `carl9170_collect_tally':
cmd.c:191: undefined reference to `__udivdi3'
cmd.c:192: undefined reference to `__udivdi3'
cmd.c:193: undefined reference to `__udivdi3'
Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here are the AR9580 1.0 initvals checksums using the
Atheros initvals-tools [1]. This is useful for when
we udate the initvals again with other values. It ensures
that we match the same initvals used internally. The
tool is documented on the wiki [2].
$ ./initvals -f ar9580-1p0
0x00000000e912711f ar9580_1p0_modes_fast_clock
0x000000004a488fc7 ar9580_1p0_radio_postamble
0x00000000f3888b02 ar9580_1p0_baseband_core
0x0000000003f783bb ar9580_1p0_mac_postamble
0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table
0x0000000094be244a ar9580_1p0_high_power_tx_gain_table
0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table
0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484
0x00000000c4d66d1b ar9580_1p0_mac_core
0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table
0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table
0x00000000301fc841 ar9580_1p0_soc_postamble
0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table
0x00000000a15ccf1b ar9580_1p0_soc_preamble
0x0000000029495000 ar9580_1p0_rx_gain_table
0x0000000037ac0ee8 ar9580_1p0_radio_core
0x00000000603a1b80 ar9580_1p0_baseband_postamble
0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1
0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1
0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq
[1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
[2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently this call back is used only in debugfs of mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the aggregation is formed till the aggregation limit
is reached and the rate lookup is done for the first frame alone.
But there can be a legacy rated frames in tid queue. This patch
limits the subframe addition based on presence of legacy rate and
sends the legacy rated frames as unaggregated one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Walsh bit is disabled for regulatory consideration.
FCC limit for walsh enable is lower than that for walsh disable. So
disabling walsh bit will not limit tx power/affect tx power even in
cases where we are not FCC limited (most client cards). If the tx
power is not FCC limited, then enabling/disabling walsh bit will
not affect Avg. EVM/overall performance in any visible manner.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In congested network, having all rate reties at MCS rates
is failing to transmit the frame offenly. By the time reaching
the success rate set, the application gets timed out. One such
scenario is that authentication time out during 4-Way handshake.
This patch uses a legacy rate as last retry sequnce for
unaggregated frames or if the first selected rate's PER is ~80%
of max limit. And also observed from the tx status that the frame
was trasmitted successfully by using legacy rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this useful for debugging and to keep track of success/failure of
frames such as ACK, RTS and FCS error count in a noisy environment
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent 8 bytes from being truncated from MGMT packets
when using TKIP.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EIFS value read from AR_D_GBL_IFS_EIFS register in core clocks and then
written back as microsecond value.
Signed-off-by: Alex Hacker <hacker@epn.ru>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9170 hardware have a 16-Bit random number generator.
The documentation claims the values are suitable for
"security keys".
The "throughput" is around 320Kibit/s. It's slow, but it
does work without introducing any special offload
firmware commands.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the
*best* channel.
Survey data from wlan22
frequency: 2412 MHz [in use]
noise: -86 dBm
channel active time: 3339608 ms
channel busy time: 270982 ms
channel transmit time: 121515 ms
Survey data from wlan22
frequency: 2417 MHz
noise: -86 dBm
channel active time: 70 ms
channel busy time: 2 ms
channel transmit time: 1 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import new headers from our firmware branch:
git://git.kernel.org/pub/scm/linux/kernel/git/chr/carl9170fw.git
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170_PWR_REG_PLL_ADDAC is used to set the main clock
divisor which affects the AHB/CPU speed. Because this
would interfere with the firmware internal timekeeping,
the function has to be moved into the firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded hardware it's normal to not have a PCI device for the PCI
bridge that the wifi card is attached to. pdev->bus->self will be
NULL in that case. In that case, simply return without emitting an
useless kernel stack trace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While switching b/w HT20/40, the current channel's nf values
are updated into history buffer. Since the current channel's
channel type, channel flag got updated before reading
nf value from hw. This channel type mismatch is causing invalid
readings when hw is on ht20 but getnf tries to read on extn chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before doing hw reset the current channel's noisefloor readings
are updated into history buffer. The extension chain's readings
are considered only if the current channel was configured in HT40.
While moving from HT40 to HT20, the extn chain's readings are
skipped though the current channel is in ht40. This patch updates
extn chain reading based on channel flag.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once RXEOL was disabled, it never be enabled again. This patch
re-enables rxeol at the end of rx tasklet.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
[<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
[<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WAR which adds extra delimiters when using RTS/CTS
with aggregation and non-enterprise AR9003 chips.
This extra padding is done after doing all the 4ms limit
checks and hence the total aggregate sizes are exceeding
the allowed duration. This patch limits the aggregate
sizes appropriately after including these extra delimiters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this callback is called during suspend/resume and also via iw command.
it configures parameters like sifs, slottime, acktimeout in
ath9k_hw_init_global_settings where few REG_READ, REG_RMW are also done
and hence the need for PS wrappers
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If is_main_vif(ar, vif) reports that we have to fall back
to software encryption, we goto err_softw; before locking ar->mutex.
As a result, we have unprotected call to carl9170_set_operating_mode
and unmatched mutex_unlock.
The patch fix the issue by adding mutex_lock before goto.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: <stable@kernel.org>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move common checks into wrapper function. Since ASPM can be only enabled
on PCIe devices ->is_pciexpress check is unneeded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.
This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the comments are obselete as the virtual wiphy support was removed from
the driver
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This cleans up error handling for the beacon in case of dma mapping
failure. We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.
Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses an issue with incorrect HW register
AR_PHY_TX_IQCAL_CORR_COEFF_B1 definition which leads to incorrect clibration.
Cc: stable@kernel.org
Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ebefce3d13 failed
to set proper PMU value to address ripple issue for AR9485.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nowhere the firmware memory is freed, free it during
the device destroy process.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes, the network manager is failing to connect to the AP due
to the below kernel crash message. The reason behind this,
after issuing the connect command to the chip, the chip is sending
disconnect event and then immediately one connect event to the host
in some random cases.
The host driver resets all states (including cfg80211 state machine)
when it receives disconnect event from the chip. But, still the host
driver reports the next received connect event to cfg80211, at that time
cfg80211 SME state would have been in IDLE state, which was causing
the below kernel crash.
Now, host driver's sme state machine is checked every time before
delivering connect event to cfg80211
WARNING: at net/wireless/sme.c:517 cfg80211_connect_result+0x10d/0x120()
[..]
Call Trace:
[<c0145732>] warn_slowpath_common+0x72/0xa0
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c0145782>] warn_slowpath_null+0x22/0x30
[<c05d676d>] cfg80211_connect_result+0x10d/0x120
[<f83ff497>] ath6kl_cfg80211_connect_event+0x427/0x4f0 [ath6kl]
[<c035d26a>] ? put_dec+0x2a/0xa0
[<c035d645>] ? number+0x365/0x380
[<c0154675>] ? mod_timer+0x135/0x260
[<c035e00e>] ? format_decode+0x2fe/0x370
[<c01263c8>] ? default_spin_lock_flags+0x8/0x10
[<c05fd91f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[<c0146032>] ? console_unlock+0x172/0x1c0
[<f8402659>] ath6kl_connect_event+0x89/0x400 [ath6kl]
[<f840826e>] ath6kl_wmi_control_rx+0x98e/0x1d60 [ath6kl]
[<c01335b5>] ? __wake_up+0x45/0x60
[<f84053aa>] ath6kl_rx+0x56a/0x770 [ath6kl]
[<c04d0242>] ? mmc_release_host+0x22/0x40
[<c04d9329>] ? sdio_release_host+0x19/0x30
[<f840a27a>] ? ath6kl_sdio_read_write_sync+0x7a/0xc0 [ath6kl]
[<f83f82b1>] do_rx_completion+0x41/0x50 [ath6kl]
[<f83faa6a>] htc_rxmsg_pending_handler+0x6ba/0xbd0 [ath6kl]
[<f8404bb0>] ? ath6kl_tx_data_cleanup+0x30/0x30 [ath6kl]
[<f840a1c0>] ? ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<f83f7cd5>] ath6kldev_intr_bh_handler+0x2a5/0x630 [ath6kl]
[<f840a1c0>] ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<c04d97c7>] sdio_irq_thread+0xc7/0x2d0
[<c013aeb0>] ? default_wake_function+0x10/0x20
[<c012fc98>] ? __wake_up_common+0x48/0x70
[<c04d9700>] ? sdio_claim_irq+0x200/0x200
[<c0163854>] kthread+0x74/0x80
[<c01637e0>] ? kthread_worker_fn+0x160/0x160
[<c0604c06>] kernel_thread_helper+0x6/0x10
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use wlan_iterate_nodes() directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the bssid from ath6kl directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is nothing but bssid of struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
And remove the reference to wmi in ath6kl_node_table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When I connect to my Linksys WT610N AP supporting 11n I see a lot of
aggreation timeout errors:
[ 408.885053] ath6kl: aggr timeout (st 3109 end 3140)
[ 463.872108] ath6kl: aggr timeout (st 3671 end 3702)
[ 495.010060] ath6kl: aggr timeout (st 3983 end 4014)
[ 503.604047] ath6kl: aggr timeout (st 4065 end 0)
[ 518.963047] ath6kl: aggr timeout (st 141 end 172)
[ 525.014066] ath6kl: aggr timeout (st 205 end 236)
[ 573.957051] ath6kl: aggr timeout (st 701 end 732)
[ 585.019067] ath6kl: aggr timeout (st 816 end 847)
But still the connection seems to work. To not clutter the logs change
the error message to a debug message. But add a fixme comment so that
this will be investigated.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl Kconfig still had dependencies to wext, remove those as they are
not needed anymore.
Now ath6kl should not have any wext code left. Time to have a beer and
celebrate this.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When ath6kl module was removed while a scan was ongoing the driver would
crash in ath6kl_cfg80211_scan_complete_event().
Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. This patch removes the
null check entirely as the wmi structure is not accessed anymore during
module unload.
Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular error code.
This is a port of my patch from ath6kl staging with the same title.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_cfg80211_scan_node() was calling cfg80211_inform_bss_frame()
with CFP_KERNEL but the function is executed with a spin lock taken.
This is wrong and the function must use GFP_ATOMIC instead.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In my setup data transfer stalls when there's data transmission during
scan. After some testing I found out that using background scan
when connected to makes the problem go away. This is more like
a workaround than a proper fix, but as the stall is so severe the
workaround is justified.
With a dual band card this increases scan time when connected from
1.9s to 4.4s. When not connected the scan time is not affected and
is the same 1.9s.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use appropriate hif function directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Endpoint id ffrom htc_packet can be used instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define a hook in ath6kl_hif_ops for hif scatter gather mechanism.
When virtual scatter gather is used, call the respective function
directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Last May we started working on cleaning up ath6kl driver which is
currently in staging. The work has happened in a separate
ath6kl-cleanup tree:
http://git.kernel.org/?p=linux/kernel/git/kvalo/ath6kl-cleanup.git;a=summary
After over 1100 (!) patches we have now reached a state where I would
like to start discussing about pushing the driver to the wireless
trees and replacing the staging driver.
The driver is now a lot smaller and looks like a proper Linux driver.
The size of the driver (measured with simple wc -l) dropped from 49
kLOC to 18 kLOC and the number of the .c and .h files dropped from 107
to 22. Most importantly the number of subdirectories reduced from 26
to zero :)
There are two remaining checkpatch warnings in the driver which we
decided to omit for now:
drivers/net/wireless/ath/ath6kl/debug.c:31:
WARNING: printk() should include KERN_ facility level
drivers/net/wireless/ath/ath6kl/sdio.c:527:
WARNING: msleep < 20ms can sleep for up to 20ms;
see Documentation/timers/timers-howto.txt
The driver has endian annotations for all the hardware specific
structures and there are no sparse errors. Unfortunately I don't have
any big endian hardware to test that right now.
We have been testing the driver both on x86 and arm platforms. The
code is also compiled with sparc and parisc cross compilers.
Notable missing features compared to the current staging driver are:
o HCI over SDIO support
o nl80211 testmode
o firmware logging
o suspend support
Testmode, firmware logging and suspend support will be added soon. HCI
over SDIO support will be more difficult as the HCI driver needs to
share code with the wifi driver. This is something we need to research
more.
Also I want to point out the changes I did for signed endian support.
As I wasn't able to find any support for signed endian annotations I
decided to follow what NTFS has done and added my own. Grep for sle16
and sle32, especially from wmi.h.
Various people have been working on the cleanup, the hall of
fame based on number of patches is:
543 Vasanthakumar Thiagarajan
403 Raja Mani
252 Kalle Valo
16 Vivek Natarajan
12 Suraj Sumangala
3 Joe Perches
2 Jouni Malinen
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Suraj Sumangala <surajs@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.
In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the previously calculated maximum of all rates instead of just the one
from the lowest rate of the selected PHY mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unnecessary includes from base.h. Add includes to other files as
necessary. Don't include base.h unless needed.
Move declarations for functions in base.c from ath5k.h to base.h.
Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When checking for the band, use channel->band.
Change ath5k_hw_nic_wakeup() and ath5k_channel_ok() to take
ieee80211_channel. Change ath5k_hw_radio_revision() to take
ieee80211_band.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
XR is a proprietary feature of the chipset. It's not supported and
should not be supported.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct ath5k_avg_val is unused.
In struct ath5k_hw, lladdr, ah_radar and ah_mac_revision are write-only,
rxbufsize is unused, ah_phy is write-only and referenced by unused
macros.
In struct ath5k_vif, lladdr is write-only.
Remove AR5K_TUNE_RADAR_ALERT, which has no effect.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver reads PCI subsystem ID from the PCI configuration register while it's
already stored by the PCI subsystem in the 'subsystem_device' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/wireless.h and net/iw_handler.h headers are
for wireless extensions only, so mac80211 drivers
shouldn't be including them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.
To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.
Bug was introduced by:
commit 53bc7aa08b
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date: Mon Apr 5 14:48:04 2010 +0530
ath9k: Add support for newer AR9285 chipsets.
Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462https://bugzilla.kernel.org/show_bug.cgi?id=37082https://bugzilla.redhat.com/show_bug.cgi?id=697157
however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
There are only two capabilities we need, and both are trivial to find.
ath5k_hw_hasbssidmask() is true on AR5212, but not on AR5210 or AR5211.
ath5k_hw_hasveol() is true on AR5211 and AR5212, but not on AR5210,
according to the HAL source.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (e.g. Ubiquiti AirRouter) ship with broken EEPROM chainmask
data, which breaks the initial calibration after a hardware reset.
To fix this, mask the eeprom chainmask with the chainmask of the chip,
and use the chip chainmask if the result is zero.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Cc: ath9k-devel@lists.ath9k.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both ath5k_hw and ath5k_softc represent one instance of the hardware.
This duplication is historical and is not needed anymore.
Keep the name "ath5k_hw" for the merged structure and "ah" for the
variable pointing to it. "ath5k_hw" is shorter than "ath5k_softc", more
descriptive and more widely used.
Put the combined structure to ath5k.h where the old ath5k_softc used to
be. Move some code from base.h to ath5k.h as needed.
Remove memory allocation for struct ath5k_hw and the corresponding error
handling. Merge iobase and ah_iobase fields.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harshal Chhaya discovered during network tests, that
several of his clients dropped-off the network. The
captured packets shows that the beacons sent by the
AP are at a much lower power than the other data
packets.
The reason for this mishap: The driver never updated
the beacon phy register, so all beacons were always
sent at the lowest power.
Reference: http://marc.info/?l=linux-wireless&m=131067225105801
Reported-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* reserves feature bit for CCA counters
* extends hardware register file definitions
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-By: christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For unicast the hardware sometimes reports MIC errors even though the
frame that it received actually contains a valid MIC - on some chips this
can happen frequently enough to trigger TKIP countermeasures.
Fix this issue by not reporting MIC errors for unicast frames with a
valid key, letting mac80211 validate the MIC instead.
Additionally, strip the MIC for all frames that the hardware considers
valid to avoid wasting CPU cycles re-validating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Instead of using ieee80211_stop_queue, check the configured tx queue
limit before calling ieee80211_get_buffered_bc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While 32 KHz sleep clock might provide some power saving benefits,
it is also a major source of stability issues, on OpenWrt it produced
some reproducible data bus errors on register accesses on several
different MIPS platforms.
All the Atheros drivers that I can find do not enable this feature,
so it makes sense to leave it disabled in ath5k as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enabling the sleep clock alters the AR5K_USEC_32 field, but disabling
it didn't restore it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During scans the full calibration usually does not make much sense,
PAPD probing and IQ calibration should be deferred until there is
enough time to complete them. Adding 100 ms to the initial full
calibration delay should be enough to do this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a division by zero when setting distance before activating the
device for the first time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Might fix some stability issues on newer chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfgain probe is only necessary for OFDM operation on AR5111 and AR5112.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Decryping frames on key_miss handling shouldn't be done for Michael
MIC failed frames as h/w would have already decrypted such frames
successfully anyway.
Also leaving CRC and PHY error(where the frame is going to be dropped
anyway), we are left to prcoess Decrypt error for which s/w decrypt is
selected anway and so having key_miss as a separate check doesn't serve
anything. So making key_miss handling mutually exlusive with other RX
status handling makes much more sense.
This patch addresses an issue with STA not reporting MIC failure events
resulting in STA being disconnected immediately.
Cc: stable@kernel.org
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_AN_SYNTH9 is in the analog shift register range and thus needs to be
written using the ath9k_hw_analog_shift_rmw function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio needs twice / four times as much time to stabilize for half/quarter
channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the clock rate is initialized properly and SIFS, EIFS, USEC,
slot time and ACK timeout are properly calculated by the generic code,
the 'async FIFO' register hacks are no longer necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the the clock-to-TSF field of AR_USEC and the SIFS and EIFS time
registers based on the clock rate instead of relying on initvals.
With those changes, some of the hardcoded AR9287 1.3+ specific overrides
can be dropped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip uses the async FIFO feature and runs the MAC at 117 MHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling half/quarter rate makes the MAC run at half/quarter clock speed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices support this, but some disable it using an EEPROM flag
for some reason. Improves 5 GHz performance on those devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the proper masks for the register instead.
Fixes adding the (still unused) half/quarter PLL flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes read only registers that cause invalid
address access and also updates index for measurement filter
calibration window size.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector calibration is disabled because this block
doesn't exist in AR9003 based chips and also parallel
calibration is enabled otherwise the calibration will never stop.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of temperature reading samples to average
during a Tx packet is decreased to 1 from 2 to improve
5G Tx EVM with chain 0-only mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
sc->imask may change if ath5k_set_current_imask() races against itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
The reg variable is only used by __raw_writel() and __raw_readl(), which
should guarantee memory access in the right order.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch imports all shared header changes
from carl9170fw.git.
* update copyright boilerplate
* add some more strategic __aligned(4).
* WoWLAN
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While sending aggregated frames in AES, the AR5416 chips
required additional padding b/w subframes. This workaround
is not needed for edma (AR9003 family) chips. With this patch
~4Mbps thoughput improvement was observed in clear environment.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Reported-by: Mark Davis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We would free the proper number of curves, but in the wrong
slots, due to a missing level of indirection through
the pdgain_idx table.
It's simpler just to try to free all four slots, so do that.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no interface has been brought up, the chip's power
state continued as AWAKE. So during resume, the chip never
been powered up.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: muddin@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The edma based (AR9003 family) chips update tx status
descriptors in a common ring buffer for all transmitted
frames. Whenever tx interrupt is raised, the descriptors
are processed and tx status index is moved.
The complete tx stauts ring are updated with beacons tx status
when there are no data frames to be sent for a period of time.
In this state, transmitting data frames causes the driver to
wait for the tx status on an incorrect tx status index though
the status was updated by hw properly. The driver detects this
condition as a h/w hang and does unnecessary chip resets.
This issue was orginally reported in adhoc mode while sending
frames after an idle time.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds a callback to ath9k_platform_data. If the
callback is provided by the platform code, then it can be
used to hard reset the WMAC device.
The callback is required for doing a hard reset of the AR9330
chips to get them working again after a hang.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds the missing configuration code for diversity
group 1.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current values must be used only on AR9485 chips. Other chips
requires different values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A multiplication is missing from the current formula.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.
Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger