The revision register is a 32 bit register. The serial_in() function reads
only the lower 16 bits of the register. This leads to an incorrect computation
of the Module revision.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
[oleksandr.savchenko@ti.com: add some whitespaces]
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current logic results in interrupt storm since the fifo
is constantly below the threshold level. Change the logic
to fill all the available spaces in the fifo as long as
we have data to minimize the possibilty of underflow and
elimiate excessive interrupts.
Signed-off-by: Dmitry Fink <finik@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wer has TX wakeup bit available enable the same
by populating the necessary tx wakeup flag for the
applicable module ip blocks and use the same
while configuaring wer reg.
Also wer is not context restored, restore wer when
context is lost.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(for drivers/tty changes)
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only enable the DMA support when the following are meet:
[1] The uart port supports the hardware flow control(CTS/RTS).
(Some uart port does not support the CTS/RTS.)
[2] The application enables the CTS/RTS.
[3] The Soc is imx6q.
For the sdma's firmware limit, we do not support the DMA except
the imx6q platform.
[4] The uart is not used as a console.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was not possible to set custom-baudrates like 62500.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will add the DMA support for the imx uart. For the firmware's limit,
only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can
support the DMA.
This patch adds the necessary macro and helper to distinguish the
imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart"
to enable the DMA support.
This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_console() check makes the clocks(clk_per and clk_ipg) opened
even when we close the console uart.
This patch enable/disable the clocks in imx_console_write(),
so we can keep the clocks closed when the console uart is closed.
Also remove the clock enable/disable oprations in the probe, we do not
need them any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the dtr_rts() hvc console callback to improve control when to
disconnect the IUCV connection. Previously, the IUCV connection was
disconnected during the notifier_del() callback, i.e., when the last file
descriptor to the hvc terminal device was closed.
Recent changes in login programs caused undesired disconnects during the
login phase. To prevent these kind of disconnects, implement the dtr_rts
callback to implicitly handle the HUPCL termios control via the hvc_console
driver.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new callback to explicitly handle the HUPCL termios control flag.
This prepares for a follow-up commit for the hvc_iucv device driver to
improve handling when to drop an established network connection.
The callback naming is based on the recently added tty_port interface to
facilitate a potential refactoring of the hvc_console to use tty_port
functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specifically:
n_gsm.c:810: ERROR: space required before the open parenthesis '('
n_gsm.c:830: WARNING: line over 80 characters
n_gsm.c:971: ERROR: trailing whitespace
n_gsm.c:984: ERROR: code indent should use tabs where possible
n_gsm.c:984: WARNING: please, no space before tabs
n_gsm.c:984: WARNING: please, no spaces at the start of a line
n_gsm.c:1141: WARNING: space prohibited before semicolon
n_gsm.c:1743: ERROR: space required before the open brace '{'
n_gsm.c:1744: WARNING: line over 80 characters
n_gsm.c:1745: ERROR: code indent should use tabs where possible
n_gsm.c:1746: ERROR: code indent should use tabs where possible
n_gsm.c:2908: WARNING: line over 80 characters
n_gsm.c:2912: ERROR: trailing whitespace
Signed-off-by: Aldo Iljazi <neonsync1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acquiring the write_wait queue spin lock now accounts for the largest
slice of cpu time on the tty write path. Two factors contribute to
this situation; a overly-pessimistic line discipline write loop which
_always_ sets up a wait loop even if i/o will immediately succeed, and
on ptys, a wakeup storm from reads and writes.
Writer wakeup does not need to be performed by the pty driver.
Firstly, since the actual i/o is performed within the write, the
line discipline write loop will continue while space remains in
the flip buffers. Secondly, when space becomes avail in the
line discipline receive buffer (and thus also in the flip buffers),
the pty unthrottle re-wakes the writer (non-flow-controlled line
disciplines unconditionally unthrottle the driver when data is
received). Thus, existing in-kernel i/o is guaranteed to advance.
Finally, writer wakeup occurs at the conclusion of the line discipline
write (in tty_write_unlock()). This guarantees that any user-space write
waiters are woken to continue additional i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LNEXT processing accounts for ~15% of total cpu time in end-to-end
tty i/o; factor the lnext test/clear from the per-char i/o path.
Instead, attempt to immediately handle the literal next char if not
at the end of this received buffer; otherwise, handle the first char
of the next received buffer as the literal next char, then continue
with normal i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always pre-figure the space available in the read_buf and limit
the inbound receive request to that amount.
For compatibility reasons with the non-flow-controlled interface,
n_tty_receive_buf() will continue filling read_buf until all data
has been received or receive_room() returns 0.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf processing; factor char receive
processing for unusual termios settings out of normal per-char
i/o path.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor 'special' per-char processing into standalone fn,
n_tty_receive_char_special(), which handles processing for chars
marked in the char_map.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the IXANY restart tty test to code paths where the
the received char is not START_CHAR, STOP_CHAR, INTR_CHAR,
QUIT_CHAR or SUSP_CHAR.
Fixes the condition when ISIG if off and one of INTR_CHAR,
QUIT_CHAR or SUSP_CHAR does not restart i/o.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify __receive_buf() into a dispatch function; perform per-char
processing for all other modes not already handled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 20bafb3d23
'n_tty: Move buffers into n_tty_data'
broke the ppc64 build.
Include vmalloc.h for the required function declarations.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf() processing; factor receive char
processing when tty->closing into n_tty_receive_buf_closing().
Note that EXTPROC when ISTRIP or IUCLC is set continues to be
handled by n_tty_receive_char().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When EXTPROC is set without ISTRIP or IUCLC, processing is
identical to raw mode; handle this receiving mode as a special-case
of raw mode.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to modal receive_buf() processing; factor raw mode
per-char i/o into n_tty_receive_buf_raw().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for modal receive_buf() handling; factor handling for
TTY_BREAK, TTY_PARITY, TTY_FRAME and TTY_OVERRUN into
n_tty_receive_char_flagged().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the monolithic n_tty_receive_char() complexity; factor the
handling of INTR_CHAR, QUIT_CHAR and SUSP_CHAR into
n_tty_receive_signal_char().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The char and flag buffer local alias pointers, p and f, are
unnecessary; remove them.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In canonical mode, an EOF which is not the first character of the line
causes read() to complete and return the number of characters read so
far (commonly referred to as EOF push). However, if the previous read()
returned because the user buffer was full _and_ the next character
is an EOF not at the beginning of the line, read() must not return 0,
thus mistakenly indicating the end-of-file condition.
The TTY_PUSH flag is used to indicate an EOF was received which is not
at the beginning of the line. Because the EOF push condition is
evaluated by a thread other than the read(), multiple EOF pushes can
cause a premature end-of-file to be indicated.
Instead, discover the 'EOF push as first read character' condition
from the read() thread itself, and restart the i/o loop if detected.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the head & commit indices from the tail index to avoid
cache-line contention (so called 'false-sharing') between concurrent
threads.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since neither echo_commit nor echo_tail can change for the duration
of __process_echoes loop, substitute index comparison for the
snapshot counter.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't have the driver flush received echoes if no echoes were
actually output.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Byte-by-byte echo output is painfully slow, requiring a lock/unlock
cycle for every input byte.
Instead, perform the echo output in blocks of 256 characters, and
at least once per flip buffer receive. Enough space is reserved in
the echo buffer to guarantee a full block can be saved without
overrunning the echo output. Overrun is prevented by discarding
the oldest echoes until enough space exists in the echo buffer
to receive at least a full block of new echoes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use output_lock mutex as a memory barrier when storing echo_commit.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding data to echo_buf (via add_echo_byte()) is guaranteed to be
single-threaded, since all callers are from the n_tty_receive_buf()
path. Processing the echo_buf can be called from either the
n_tty_receive_buf() path or the n_tty_write() path; however, these
callers are already serialized by output_lock.
Publish cumulative echo_head changes to echo_commit; process echo_buf
from echo_tail to echo_commit; remove echo_lock.
On echo_buf overrun, claim output_lock to serialize changes to
echo_tail.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for lockless echo_buf handling; compute current byte count
of echo_buf from head and tail indices.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a single index to track the current echo_buf position,
use a head index when adding to the buffer and a tail index when
consuming from the buffer. Allow these head and tail indices to wrap
at max representable value; perform modulo reduction via helper
functions when accessing the buffer.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The echo_overrun field is only assigned and never tested; remove it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_BUFFER_PAGE is only used within drivers/tty/tty_buffer.c;
relocate to that file scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the tty_buffer_flush() exclusion mechanism to a
public interface - tty_buffer_lock/unlock_exclusive() - and use
the interface to safely write the paste selection to the line
discipline.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__tty_flush_buffer() is now only called by tty_flush_buffer();
merge functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ruchika Kharwar