Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dead code as well.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
s3c_hsotg_process_req_feature comments was not correct
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When clearing HALT on an endpoint, req->complete of in progress
requests must be called with locks off. New request should only be
started if there is not already a pending request on the endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb bus is reset without a physical disconnection, all endpoints
will remain open. Call s3c_hsotg_disconnect() from reset handler to
report a disconnect to gadget framework. hsotg->connected is checked
in s3c_hsotg_disconnect() before processing disconnect.
In some cases, USBRst is seen before EnumDone and after it as well.
So move setting of hsotg->connected to set-address to avoid reporting
extra disconnection in this case.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When booting with id pin grounded, dwc2 default to host mode.
Thus, force device mode prior initializing gadget part.
Else fifo init will fail since fifo values are not correct
in host mode.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This callback informs the driver about the total amount of current it
is allowed to draw. Share this information with the phy so that
current limits can be set for charging for example.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is
removed.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.
Moreover, only use signed variables when required.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Can't stay in the loop forever. Break it after timeout.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.
For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current code does not check endpoint 15 interrupt. Use number
of endpoint configured in hardware instead of the hardcoded value.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do a read-modify-write instead of only setting DMAEn bit.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst-
length at correct position.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the error path, s3c_hsotg_phy_disable should be called after a
call to s3c_hsotg_phy_enable is made.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can
occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs
with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled.
Moreover, ignore DOEPINT.XferCompl when it occurs with
DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to
continue.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, keep fifo empty interrupt disabled. Otherwise
core is flooded by interrupts.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bind peripheral controller to the phy on udc_start. Unbind on
udc_stop.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes in simpler way the bug described in [1] and [2]. It
looks like DWC2 is the only UDC driver that doesn't force usb requests
to complete in ep_disable() function. This causes described problem,
because we have no guarantee that all requests will be completed before
unbind of usb function.
To fix this problem we force all requests of disabled endpoint to complete.
Also currently running request is not handled. This allowed to simplify
code of kill_all_requests() function, because 'force' parameter is always
set to true, so we don't need it anymore.
In s3c_hsotg_rx_data() we change function used to print message when active
request is NULL from dev_warn() to dev_dbg(), because such situation is
harmless for driver and now it can take place during normal endpoint
disabling.
[1] https://lkml.org/lkml/2014/12/9/283
[2] https://lkml.org/lkml/2014/12/12/360
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes us sure that all requests are completed before we unbind
gadget. There are assumptions in gadget API that all requests have to
be completed and leak of complete can break some usb function drivers.
For example unbind of ECM function can cause NULL pointer dereference:
[ 26.396595] configfs-gadget gadget: unbind function
'cdc_ethernet'/e79c4c00
[ 26.414999] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
(...)
[ 26.452223] PC is at ecm_unbind+0x6c/0x9c
[ 26.456209] LR is at ecm_unbind+0x68/0x9c
(...)
[ 26.603696] [<c033fdb4>] (ecm_unbind) from [<c033661c>]
(purge_configs_funcs+0x94/0xd8)
[ 26.611674] [<c033661c>] (purge_configs_funcs) from [<c0336674>]
(configfs_composite_unbind+0x14/0x34)
[ 26.620961] [<c0336674>] (configfs_composite_unbind) from
[<c0337124>] (usb_gadget_remove_driver+0x68/0x9c)
[ 26.630683] [<c0337124>] (usb_gadget_remove_driver) from [<c03376c8>]
(usb_gadget_unregister_driver+0x64/0x94)
[ 26.640664] [<c03376c8>] (usb_gadget_unregister_driver) from
[<c0336be8>] (unregister_gadget+0x20/0x3c)
[ 26.650038] [<c0336be8>] (unregister_gadget) from [<c0336c84>]
(gadget_dev_desc_UDC_store+0x80/0xb8)
[ 26.659152] [<c0336c84>] (gadget_dev_desc_UDC_store) from
[<c0335120>] (gadget_info_attr_store+0x1c/0x28)
[ 26.668703] [<c0335120>] (gadget_info_attr_store) from [<c012135c>]
(configfs_write_file+0xe8/0x148)
[ 26.677818] [<c012135c>] (configfs_write_file) from [<c00c8dd4>]
(vfs_write+0xb0/0x1a0)
[ 26.685801] [<c00c8dd4>] (vfs_write) from [<c00c91b8>]
(SyS_write+0x44/0x84)
[ 26.692834] [<c00c91b8>] (SyS_write) from [<c000e560>]
(ret_fast_syscall+0x0/0x30)
[ 26.700381] Code: e30409f8 e34c0069 eb07b88d e59430a8 (e5930000)
[ 26.706485] ---[ end trace f62a082b323838a2 ]---
It's because in some cases request is still running on endpoint during
unbind and kill_all_requests() called from s3c_hsotg_udc_stop() function
doesn't cause call of complete() of request. Missing complete() call
causes ecm->notify_req equals NULL in ecm_unbind() function, and this
is reason of this bug.
Similar breaks can be observed in another usb function drivers.
This patch fixes this bug forcing usb request completion in when
s3c_hsotg_ep_disable() is called from s3c_hsotg_udc_stop().
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUdJoNAAoJEIaOsuA1yqREqDoP/iwVojhk1qb2PQAJvLkl8To4
R34RM8zt8IRhE+yWIW8hm8xvsLiwvujBMgsphUmyu2k0X/NtPl1ElrDvObWwO0N8
ouyLISRw/wLUs8hJwsNVhIX0VjPxDQ6648C3OZYjySTtNtsh0rBw84ALX+IWkDye
Thb823xEunGYVwjhq8WrfT94q6LjyPp00XHlA4mf3XgSpXC2tKBFGmIcfmwObzYI
LkON7kJTp14XEeIYGYJO+7MBpo8s7YFmnpsDOV2QYlz/i0pRdjLwaKMN5T7D7DO5
YdvcQFQUM53dvq+tiw2k2iW4gmn9ktHHlckn8W5hhQZCs4ujSzYy/vP4GcbNEaTf
CuDocJGTr7ieU2IqYiTM+wRYavBoHLq9V5AHZmgsZ/pVF8lvG0hcX0fmd7XXScjv
GaKJqyQMaKZ9tRF9RZdMZeOrICp1X1X+KcqdG7yXoOtsVdn0O3zHdxYcZcVa29X/
cXuttoTywQgfrlI/uWWwpkYlqiHeawK1EooZ/6fYQDviLm4lrLPp94vF/5MqGM1j
f2tNpG63iOzLUUYJa+YgPqs6RrZLM3soZcf3bFAEt9sA99gc3ExwCYXurBEnTONr
XUowTfNKxPaVjNPZ1evGwF5F+WLEK4s88weB9lArd2S3NFP3DQV1cRpWj8rLYE72
lX6aWEWUDqnUHmwJUgIb
=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we have assigned clk=NULL, which is a valid clk, we should not
be returning when a clock node is not provide. Instead, we should return
only when we cannot enable the clock.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Suspend/resume code assumed that the gadget was always started and
enabled to connect to usb bus. This means that the actual state of the
gadget (started/stopped or connected/disconnected) was not correctly
preserved on suspend/resume cycle. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds mutex, which protects initialization and
deinitialization procedures against suspend/resume methods. This mutex
will be needed by the updated suspend/resume calls, which tracks gadget
state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a call to s3c_hsotg_disconnect() from 'end session'
interrupt (GOTGINT_SES_END_DET) to correctly notify gadget subsystem
about unplugged usb cable. DISCONNINT interrupt cannot be used for this
purpose, because it is asserted only in host mode.
To avoid reporting disconnect event more than once, a disconnect call has
been moved from USB_REQ_SET_ADDRESS handling function to SESSREQINT
interrupt. This way driver ensures that disconnect event is reported
either when usb cable is unplugged or every time the host starts a new
session. To handle devices which has been synthesized without
SRP support, connected state is set in ENUMDONE interrupt.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the dwc2 hcd driver is currently not looking for a clock node during
init, we should not completely fail if there isn't a clock provided.
By assigning clk = NULL, this allows the driver, when configured for dual-role
mode, to be able to continue loading the host portion of the driver when
a clock node is not specified.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc2_handle_common_intr call the gadget interrupt function when operating
in peripheral mode. Remove the spinlock functions in s3c_hsotg_irq as
dwc2_handle_common_intr() already has the spinlocks.
Move the registeration of the IRQ to common code for platform and PCI.
Remove duplicate interrupt conditions that was in gadget, as those are handled
by dwc2 common interrupt handler.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds the gadget data structure and appropriate data structure pointers
to the common dwc2_hsotg data structure. To keep the driver data
dereference code looking clean, the gadget variable declares are only available
for peripheral and dual-role mode. This is needed so that the dwc2_hsotg data
structure can be used by the hcd and gadget drivers.
Updates gadget.c to use the dwc2_hsotg data structure and gadget pointers
that have been moved into the common dwc2_hsotg structure.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves calls to phy enable/disable out of spinlock protected
blocks in device suspend/resume to fix incorrect caller context. Phy
related functions must not be called from atomic context. To protect
device internal state from a race during suspend, a call to
s3c_hsotg_core_disconnect() is added under a spinlock, what prevents any
further activity on the usb bus.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves udc initialization from pullup() method to
s3c_hsotg_udc_start(), so that method ends with hardware fully
initialized and left in soft-disconnected state. After this change, the
pullup() method simply clears soft-disconnect start() when called with
is_on=1. For completeness, a call to s3c_hsotg_core_disconnect() has
been added when pullup() method is called with is_on=0, what puts the
udc hardware back to soft-disconnected state.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves phy enable/disable calls from pullup() method to
udc_start/stop functions. This solves the issue related to limited caller
context for PHY functions, because they cannot be called from non-sleeping
context. This is also a preparation for using soft-disconnect feature of
udc controller in pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch changes s3c_hsotg_core_init function to leave hardware in
soft disconnect mode, so the moment of coupling the hardware to the usb
bus can be later controlled by the separate functions for enabling and
disabling soft disconnect mode. This patch is a preparation to rework
pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes duplicated code and sets last_rst variable in the
function which does the hardware reset.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Excessive debug messages might cause timing issues that prevent correct
usb enumeration. This patch hides information about USB bus reset to let
driver enumerate fast enough to avoid making host angry. This fixes
endless enumeration and usb reset loop observed with some Linux hosts.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes probe function to match the pattern used elsewhere in
the driver, where power regulators are turned off as the last element in
the device shutdown procedure.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_stop() should clear ->driver pointer unconditionally to let the UDC
framework to work correctly with both registering/unregistering gadgets
and enabling/disabling gadgets by writing to
/sys/class/udc/*hsotg/soft_connect interface.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse was giving the following warning:
warning: context imbalance in 's3c_hsotg_ep_enable'
- different lock contexts for basic block
we were returning ENOMEM while still holding the spinlock.
The sparse warning was fixed by releasing the spinlock before return.
Cc: <stable@vger.kernel.org> # v3.17
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the part of code that initializes the PHY bus width.
This results in simpler code and removes the need to check whether
the Generic PHY Framework is used.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is stopped or suspended clock is not needed so we
can disable it for this time.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.
Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.
It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DWC2/s3c-hsotg debug messages are really useless for typical user,
so hide them behind dev_dbg().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the debug text to the name of the printed variable.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/dwc2/gadget.c: In function 's3c_hsotg_irq_enumdone':
linux-2.6/drivers/usb/dwc2/gadget.c:1904: warning: 'ep_mps' may be used uninitialized in this function
Acked-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file and folder movements resulted in the incorrect reference.
So for better code maintainability, let's remove it.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch errors as belows.
ERROR: open brace '{' following function declarations go on the next line
ERROR: space required before the open parenthesis '('
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
%pad notation automatically prints in hexadecimal format (with '0x'), so remove
the unneeded '0x' to avoid a '0x0x' string.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse warns about the __le16 wValue from the USB SetAddress
command being used without converting it to CPU endianness. Fix
that, and also add a bit of defensive masking of the received
wValue before using it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the data structures that are in the s3c-hsotg
source into core.h. This is a necessary step towards unifying
the s3c-hsotg and dwc2 into a single DRD.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb,fb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[ pz - Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moves the s3c-hsotg driver into the dwc2 directory and uses the
dwc2 defines in hw.h. Renames s3c-hsotg.c to gadget.c.
NOTE: You can build both host and peripheral as a dynamically
linked module, but be aware that if you insmod dwc2_gadget, then
rmmod it, then insmod dwc2 and dwc2_platform for host mode, this
will not work. As the step to rmmod dwc2_gadget.ko will turn off
the clock to the USB IP. The dwc2 host driver currently does not
look to turn on a clock yet. A patch to fix that will be coming
soon.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
[ pz: Folded Kconfig/Makefile changes, which were originally in
a separate patch, into this one, to avoid a build breakage.
Modified Kconfig/Makefile changes a bit. Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gregory Herrero